The Generic Interrupt Controller (version 3) offers services that are
similar to GICv2, with a number of additional features:
- Affinity routing based on the CPU MPIDR (ARE)
- System register for the CPU interfaces (SRE)
- Support for more that 8 CPUs
- Locality-specific Peripheral Interrupts (LPIs)
- Interrupt Translation Services (ITS)

This patch adds preliminary support for GICv3 with ARE and SRE,
non-secure mode only. It relies on higher exception levels to grant ARE
and SRE access.

Support for LPI and ITS will be added at a later time.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: NZi Shen Lim <zlim@broadcom.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: NTirumalesh Chalamarla <tchalamarla@cavium.com>
Reviewed-by: NYun Wu <wuyun.wu@huawei.com>
Reviewed-by: NZhen Lei <thunder.leizhen@huawei.com>
Tested-by: Tirumalesh Chalamarla<tchalamarla@cavium.com>
Tested-by: NRadha Mohan Chintakuntla <rchintakuntla@cavium.com>
Acked-by: NRadha Mohan Chintakuntla <rchintakuntla@cavium.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Reviewed-by: NMark Rutland <mark.rutland@arm.com>
Link: https://lkml.kernel.org/r/1404140510-5382-3-git-send-email-marc.zyngier@arm.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Bit[9:0] is interrupt ID field in GICC_IAR. Bit[12:10] is CPU ID field,
and others are reserved.

So we should use GICC_IAR_INT_ID_MASK to get interrupt ID. It's not a good way
to use ~0x1c00 (CPU ID field) to get interrupt ID.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
Link: https://lkml.kernel.org/r/1399795571-17231-3-git-send-email-haojian.zhuang@linaro.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

This adds support for a VIC to be cascaded off another IRQ.
On the Integrator/AP logical module IM-PD1 there is a VIC
cascaded off the central FPGA IRQ controller so this is
needed for that to work out.

In order for the plug-in board to be able to register all
the devices with their IRQs relative to the offset of the
base obtained for the cascaded VIC, the base IRQ number
is passed back to the caller.

Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Some socs have a large number of interrupts requests to service
the needs of its many peripherals and subsystems. All of the
interrupt lines from the subsystems are not needed at the same
time, so they have to be muxed to the irq-controller appropriately.
In such places a interrupt controllers are preceded by an CROSSBAR
that provides flexibility in muxing the device requests to the controller
inputs.

This driver takes care a allocating a free irq and then configuring the
crossbar IP as a part of the mpu's irqchip callbacks. crossbar_init should
be called right before the irqchip_init, so that it is setup to handle the
irqchip callbacks.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: NSricharan R <r.sricharan@ti.com>
Acked-by: Kumar Gala <galak@codeaurora.org> (for DT binding portion)
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NThomas Gleixner <tglx@linutronix.de>

In some socs the gic can be preceded by a crossbar IP which
routes the peripheral interrupts to the gic inputs. The peripheral
interrupts are associated with a fixed crossbar input line and the
crossbar routes that to one of the free gic input line.

The DT entries for peripherals provides the fixed crossbar input line
as its interrupt number and the mapping code should associate this with
a free gic input line. This patch adds the support inside the gic irqchip
to handle such routable irqs. The routable irqs are registered in a linear
domain. The registered routable domain's callback should be implemented
to get a free irq and to configure the IP to route it.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: NSricharan R <r.sricharan@ti.com>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

MX is an interrupt distributor used in some SMP-capable xtensa
configurations.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

Extract xtensa built-in interrupt controller implementation from
xtensa/kernel/irq.c and move it to other irqchips, providing way to
instantiate it from the device tree.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

Define CPU interface offsets for the GICC_ABPR, GICC_APR, and GICC_IIDR
registers.  Define distributor registers for the GICD_SPENDSGIR and the
GICD_CPENDSGIR.  KVM/ARM needs to know about these definitions to fully
support save/restore of the VGIC.

Also define some masks and shifts for the various GICH_VMCR fields.

Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

This patch converts irq-bcm2835 driver to use the new IRQCHIP_DECLARE and
irqchip_init.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The regular gic_raise_softirq() takes as input a CPU mask which is not
adequate when we need to send an IPI to a CPU which is not represented
in the kernel to GIC mapping.  That is the case with the b.L switcher
when GIC migration to the inbound CPU has not yet occurred.
Signed-off-by: NNicolas Pitre <nico@linaro.org>

In order to have early assembly code signal other CPUs in the system,
we need to get the physical address for the SGIR register used to
send IPIs.  Because the register will be used with a precomputed CPU
interface ID number, there is no need for any locking in the assembly
code where this register is written to.
Signed-off-by: NNicolas Pitre <nico@linaro.org>

When processors are about to hit low power states, the assertion of
standbywfi signal, triggered by the wfi instruction, is essential to
entering low power modes. If an IRQ is pending on the processor at the
time wfi is issued, the wfi instruction completes and the processor
restarts execution without asserting the standbywfi signal. Depending
on the platform power controller HW this behaviour can be acceptable or
not; if this behaviour must be prevented software should be provided
with a way to disable the routing of interrupts to the core IRQ pins.

On systems where raw GIC distributor interrupts are connected to the power
controller as wake-up events (hence the power controller still senses
IRQs and can wake up cores upon IRQ pending), the GIC CPU interface can
be disabled on power down, so that the GIC CPU IF output is gated and wfi
cannot complete, thereby preventing the standbywfi issue.

This patch adds a simple function to the GIC driver that allows to
disable the GIC CPU IF from power down procedures.
Signed-off-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[rewrote commit log]
Signed-off-by: NOlof Johansson <olof@lixom.net>

pxa910_set_wake() & mmp2_set_wake() are both declared in head files
of arch/arm/mach-mmp/include/mach directory. If we include these
head files in irq-mmp driver, it blocks the multiplatform build.
So adjust the code.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@gmail.com>

Currently, GIC IDs are hardcoded making the code dependent on the 4+4 b.L
configuration.  Let's allow for GIC IDs to be discovered upon switcher
initialization to support other b.L configurations such as the 1+1 one,
or 2+3 as on the VExpress TC2.
Signed-off-by: NNicolas Pitre <nico@linaro.org>

This is required by the big.LITTLE switcher code.

The gic_migrate_target() changes the CPU interface mapping for the
current CPU to redirect SGIs to the specified interface, and it also
updates the target CPU for each interrupts to that CPU interface
if they were targeting the current interface.  Finally, pending
SGIs for the current CPU are forwarded to the new interface.

Because Linux does not use it, the SGI source information for the
forwarded SGIs is not preserved.  Neither is the source information
for the SGIs sent by the current CPU to other CPUs adjusted to match
the new CPU interface mapping.  The required registers are banked so
only the target CPU could do it.
Signed-off-by: NNicolas Pitre <nico@linaro.org>

This allows to remove some boilerplate code. At the same time, call the
set_handle_irq function in the initialization function of the irqchip,
so that we can remove it from the machine declaration.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Move icoll.c into drivers/irqchip as irq-mxs.c, and along with the
renaming, change the driver to use IRQCHIP_DECLARE.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

All the calls to gic_secondary_init() pass 0 as the first argument.
Since this function is called on each CPU when starting, it can be done
in a platform-independent way via a CPU notifier registered by the GIC
code.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Tested-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Tested-by: NDinh Nguyen <dinguyen@altera.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Tested-by: NMarc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Barry Song <baohua.song@csr.com>

These functions have been introduced by commit 10a8c383 (irq: introduce
entry and exit functions for chained handlers) in asm/mach/irq.h. This
patch moves them to linux/irqchip/chained_irq.h so that generic irqchip
drivers do not rely on architecture specific header files.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Tested-by: NMarc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>

Meta core internal interrupts (from HWSTATMETA and friends) are vectored
onto the TR1 core trigger for the current thread. This is demultiplexed
in irq-metag.c to individual Linux IRQs for each internal interrupt.

External SoC interrupts (from HWSTATEXT and friends) are vectored onto
the TR2 core trigger for the current thread. This is demultiplexed in
irq-metag-ext.c to individual Linux IRQs for each external SoC interrupt.
The external irqchip has devicetree bindings for configuring the number
of irq banks and the type of masking available.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Dom Cobley <popcornmix@gmail.com>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-doc@vger.kernel.org

The GIC include file being used by some of the KVM assembly code,
wrap the C definitions with a #ifdef __ASSEMBLY__ guard.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

The GICH_* constants are defined by the GIC HW spec, and even though
they only be used by KVM to begin with, define them generically in gic.h.
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NChristoffer Dall <c.dall@virtualopensystems.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Add missing register map offsets for the distributor and rename
GIC_DIST_ACTIVE_BIT to GIC_DIST_ACTIVE_SET to be consistent.
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NChristoffer Dall <c.dall@virtualopensystems.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Now that we have VIC moved to drivers/irqchip and all VIC DT init for
platforms using irqchip_init, move gic.h and update the remaining
includes.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org

Now that we have GIC moved to drivers/irqchip and all GIC DT init for
platforms using irqchip_init, move gic.h and update the remaining
includes.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>

This patch moves shirq interrupt controllers driver and header file out of
plat-spear directory. It is moved to drivers/irqchip/ directory.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
CC: Thomas Gleixner <tglx@linutronix.de>

This moves the Versatile FPGA interrupt controller driver, used in
the Integrator/AP, Integrator/CP and some Versatile boards, out
of arch/arm/plat-versatile and down to drivers/irqchip where we
have consensus that such drivers belong. The header file is
consequently moved to <linux/platform_data/irq-versatile-fpga.h>.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The BCM2835 contains a custom interrupt controller, which supports 72
interrupt sources using a 2-level register scheme. The interrupt
controller, or the HW block containing it, is referred to occasionally
as "armctrl" in the SoC documentation, hence the symbol naming in the
code.

This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split as of 2012/09/08, and modified as follows:

* s/bcm2708/bcm2835/.
* Modified device tree vendor prefix.
* Moved implementation to drivers/irchip/.
* Added devicetree documentation, and hence removed list of IRQs from
  bcm2835.dtsi.
* Changed shift in MAKE_HWIRQ() and HWIRQ_BANK() from 8 to 5 to reduce
  the size of the hwirq space, and pass the total size of the hwirq space
  to irq_domain_add_linear(), rather than just the number of valid hwirqs;
  the two are different due to the hwirq space being sparse.
* Added the interrupt controller DT node to the top-level of the DT,
  rather than nesting it inside a /axi node. Hence, changed the reg value
  since /axi had a ranges property. This seems simpler to me, but I'm not
  sure if everyone will like this change or not.
* Don't set struct irq_domain_ops.map = irq_domain_simple_map, hence
  removing the need to patch include/linux/irqdomain.h or
  kernel/irq/irqdomain.c.
* Simplified armctrl_of_init() using of_iomap().
* Removed unused IS_VALID_BANK()/IS_VALID_IRQ() macros.
* Renamed armctrl_handle_irq() to prevent possible symbol clashes.
* Made armctrl_of_init() static.
* Removed comment "Each bank is registered as a separate interrupt
  controller" since this is no longer true.
* Removed FSF address from license header.
* Added my name to copyright header.
Signed-off-by: NChris Boot <bootc@bootc.net>
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NDom Cobley <popcornmix@gmail.com>
Signed-off-by: NDom Cobley <dc4@broadcom.com>
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>