Also mark the LP-PHY driver "802.11a/g" instead of "802.11g",
as LP-PHY is capable of both 2GHz and 5GHz operation.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

-Make use of the b43_phy_set/mask/maskset helpers.
-Fix a few errors in the code.
-Make the code more readable.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Significant literature suggests users use debug flags 0x43fff - this causes
the debug flags to be set that causes information to be printed for every
received frame - including beacons. In the best case it fills up the logs,
at worst it slows driver down and causes failures due to timeouts.

In the RX handler, print debugging only if user requested RX debugging.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

3945 does not have update_chain_flags defined and because if this we always
see the debug message that does not apply to it. Add a check to be specific
about what is actually happening.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some concerns were raised about the automatic adjustment
of sleep intervals to all the same, potentially high,
value, and I can imagine the hardware behaving better
when we don't ask too much of it.

So let's convert to use a succession of sleep levels
when requesting to go to deeper sleeps (which can only
happen with large DTIM intervals), using the succession
values from power level three, which have the benefit of
also having been tested extensively already.

As a result, the automatic sleep level adjustment will
now be mostly equivalent to power level three, except
for the RX/TX timeouts and possibly using smaller sleep
vectors to account for networking latency.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For HT packets, mac80211 expects the rate_idx to be an MCS number, which is the
lower byte of rate_n_flags.  However, iwl_hwrate_to_plcp_idx takes the MCS
number and reduces it down to the range 0-8 (6 to 60 Mbps), removing the bits
that signify multiply streams, HT40 Duplicate mode, or unequal modulation.
This version is used for various internal purposes through the driver.

Add the function iwl_hwrate_get_mac80211_idx, an alternate version which takes
the rate and the band and returns the mac80211 index (MCS, for HT packets, and
PLCP rate, for legacy packets).
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Refactor and correct rate selection for outgoing transmitted
packets.

First, note that HT rates in the mac80211 rate table do not provide valid
indices when ieee80211_get_tx_rate is called; the check to see if we could to
abort a transmission early in iwl_tx_skb() would thus occasionally read invalid
memory and occasionally stall transmission (if the erroneous byte was 0xff).
We remove that code; the check wasn't valid anyway.

Second, iwl_tx_cmd_build_rate() also called ieee80211_get_tx_rate to be used
for sending management packets, which do not use the uCode station table.  This
patch refactors that function and adds comments to enhance legibility, replaces
the call to ieee80211_get_tx_rate() with a direct lookup, and adds error
handling in case the table entry is invalid.
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_supported_band is supposed to only contain legacy rates in the
bitrates table (HT rates go in the ieee80211_sta_ht_cap substruct).  Make
iwlwifi driver obey this restriction by removing the 60 Mbps rate. Also, clean
up a few pieces of other code that formerly relied on 60 Mbps being in
sband->bitrates.
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Most of the places in debugfs.c are missing a NULL check on the return value of
get_zeroed_page API call. Added required NULL check at appropriate places.
Signed-off-by: NKiran Divekar <kirandivekar@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that cfg80211 functions are added and wext converted to use wext-compat
functions, remove wext structures and disabled code.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Stats worker no longer poll stats from device anymore. It's still
needed to poll device control channel for connect/disconnect events,
so rename stats worker as device poller.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add cfg80211 get_station and convert SIOCGIWRATE and get_wireless_stats
to cfg80211.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add cfg80211 add_key/del_key/set_default_key and convert wext to use theim.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add cfg80211 set_channel and convert wext to use it.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add cfg80211 connect functions for station and ad-hoc modes and
convert wext to use theim.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Random essid must be set to turn on radio when not connected. If device is
in ad-hoc mode, this results 'media connect' indications with the random
essid which should be ignored.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use is_zero_ether_addr() and is_broadcast_ether_addr() instead of
memcmp against ffff_bssid/zero_bssid.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move link up/down work to separate functions and use local array
for allocating memory for info structure instead of kzmalloc.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Increase scan delay from 1 sec to 6 sec. Spec says that scan by
OID_802_11_BSSID_LIST_SCAN completes in 6 seconds.
Before rfkill patch too short delay was not problem as device was
always active (radio on) and performing background scanning.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Buffer used for bssid list might be too small. Change rndis_query_oid()
to return required buffer length to caller and make rndis_check_bssid_list()
resize buffer when needed.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

OID_802_11_BSSID_LIST_SCAN clears device's bssid list, so retrieve
current bssid list from device before issuing new scan.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Setting WPA keys with OID_802_11_ADD_KEY sometimes trigger
instant media connect indication. These indications are extranous and
should be ignored, as otherwise driver would send reassociation event to
userspace which in this case is not needed.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The A/G-PHY changes are fallout fixes from the enum change,
which in turn allows the LP-PHY code to be much simpler.
The antenna_to_phyctl change is a fix for a potential
existing bug that this patch may otherwise trigger.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The most common LP-PHY device, BCM4312, is now fully functional.
So, no need to say "probably won't work for you" anymore.
It's also not "for debuggers and developers only", as it is
perfectly usable for end-users now (at least for BCM4312).
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR5K_SREV is available even if the chip has been put to sleep.  Relying
on the chip register allows binding non-standard PCI IDs by

echo VENDOR_ID PRODUCT_ID >/sys/bus/pci/drivers/ath5k/new_id

without having to specify the driver data as well.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The `val' variable in ath5k_eeprom_read_turbo_modes() is used
uninitialized.  gcc 4.4.1 with -fno-inline-functions-called-once reports
it:

eeprom.c: In function 'ath5k_eeprom_read_turbo_modes':
eeprom.c:441: warning: 'val' may be used uninitialized in this function

Comparing the code to the Atheros HAL, it's clear that the split between
ath5k_eeprom_read_modes() and ath5k_eeprom_read_turbo_modes() was
incorrect.

The Atheros HAL reads both turbo and non-turbo data from EEPROM in one
function.  Some turbo mode parameters are derived from the same EEPROM
values as non-turbo parameters, just from different bits.

Merge ath5k_eeprom_read_turbo_modes() into ath5k_eeprom_read_modes() to
fix the warning.  The actual values and offsets have been cross-checked
against Atheros HAL.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As Pavel Roskin noted, the check for mac version as copied from
legacy_hal made no sense.  This replaces it with the equivalent
and makes up a suitable #define for the mac version legacy_hal
checked.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After some discussion on IRC about the PHY register write change,
I am not sure anymore if this is the right thing to do.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ICT IRQ table is a set of __le32 values, not u32 values,
so when reading it we need to take into account that it has
to be converted to CPU endianness. This was causing a lot of
trouble on my powerpc box where various things would simply
not work for no apparent reason with 5xxx cards, but worked
with 4965 -- which doesn't use the ICT table.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since patch "rt2x00: bss_info_changed() callback is allowed to sleep" the
variable delayed wasn't used anymore. This means it can be removed
along with the call to schedule_work which depended on that variable.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement the "PMU LDO set voltage" and "PMU LDO PA ref enable"
functions, and use them during LP-PHY baseband init in b43.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

-Fix a few nasty typos (b43_phy_* operations instead of b43_radio_*)
 in the channel tune routines.
-Fix some typos & spec errors found by MMIO tracing.
-Optimize b43_phy_write & b43_phy_mask/set/maskset to use
 only the minimal number of MMIO accesses. (Write is possible
 using a single 32-bit MMIO write, while set/mask/maskset can
 be done in 3 16-bit MMIOs).
-Set the default channel back to 1, as the bug forcing us to use
 channel 7 is now fixed.

With this, the device comes up, scans, associates, transmits,
receives, monitors and injects on all channels - in other words,
it's fully functional. Sensitivity and TX power are still sub-optimal,
due to the lack of calibration (that's next on my list).
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Qdiv roundup routine is essentially a fixed-point
division algorithm, using only integer math.
However, the version in the specs had a major error
that has been recently fixed (a missing quotient++).

Replace Qdiv roundup with a rewritten, simplified version.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change implements rfkill support for RTL8187B and RTL8187L devices,
using new cfg80211 rfkill API.
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Larry Finger reports following lockdep warning:

[ INFO: possible circular locking dependency detected ]
2.6.31-rc6-wl #201
-------------------------------------------------------
rfkill/30578 is trying to acquire lock:
 (&(&priv->work)->work#2){+.+...}, at: [<ffffffff81051215>]
__cancel_work_timer+0xd9/0x222

but task is already holding lock:
 (&priv->conf_mutex#2){+.+.+.}, at: [<ffffffffa064a024>]
rtl8187_stop+0x31/0x364 [rtl8187]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (&priv->conf_mutex#2){+.+.+.}:
       [<ffffffff81065957>] __lock_acquire+0x12d0/0x1614
       [<ffffffff81065d54>] lock_acquire+0xb9/0xdd
       [<ffffffff8127c32f>] mutex_lock_nested+0x56/0x2a8
       [<ffffffffa064a392>] rtl8187_work+0x3b/0xf2 [rtl8187]
       [<ffffffff81050758>] worker_thread+0x1fa/0x30a
       [<ffffffff81054ca5>] kthread+0x8f/0x97
       [<ffffffff8100cb7a>] child_rip+0xa/0x20
       [<ffffffffffffffff>] 0xffffffffffffffff

-> #0 (&(&priv->work)->work#2){+.+...}:
       [<ffffffff8106568c>] __lock_acquire+0x1005/0x1614
       [<ffffffff81065d54>] lock_acquire+0xb9/0xdd
       [<ffffffff8105124e>] __cancel_work_timer+0x112/0x222
       [<ffffffff8105136b>] cancel_delayed_work_sync+0xd/0xf
       [<ffffffffa064a33f>] rtl8187_stop+0x34c/0x364 [rtl8187]
       [<ffffffffa0242866>] ieee80211_stop_device+0x29/0x61 [mac80211]
       [<ffffffffa0239194>] ieee80211_stop+0x476/0x530 [mac80211]
       [<ffffffff8120ce15>] dev_close+0x8a/0xac
       [<ffffffffa01d9fa7>] cfg80211_rfkill_set_block+0x4a/0x7a [cfg80211]
       [<ffffffffa01bf4f0>] rfkill_set_block+0x84/0xd9 [rfkill]
       [<ffffffffa01bfc31>] rfkill_fop_write+0xda/0x124 [rfkill]
       [<ffffffff810cf286>] vfs_write+0xae/0x14a
       [<ffffffff810cf3e6>] sys_write+0x47/0x6e
       [<ffffffff8100ba6b>] system_call_fastpath+0x16/0x1b
       [<ffffffffffffffff>] 0xffffffffffffffff

The problem here is that rtl8187_stop, while helding priv->conf_mutex,
runs cancel_delayed_work_sync on an workqueue that runs rtl8187_work,
which also takes priv->conf_mutex lock. Move cancel_delayed_work_sync
out of rtl8187_stop priv->conf_mutex locking region.
Reported-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>