This follows the sparc changes a439fe51.

Most of the moving about was done with Sam's directions at:

http://marc.info/?l=linux-sh&m=121724823706062&w=2

with subsequent hacking and fixups entirely my fault.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use clk_always_enable() in the sh7366 processor code.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use clk_always_enable() on the sh7343 processor and in the board code
for Solution Engine 7343. Remove duplicate MSTPCR register definitions.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use clk_always_enable() on the sh7722 processor and in the board code
for Migo-R and Solution Engine 7722. Remove duplicate MSTPCR register
definitions.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use clk_always_enable() on the sh7723 processor and in the ap325rxa
board code. Remove duplicate MSTPCR register definitions.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Show all clocks in /proc/clocks, and also show if they are enabled or
disabled. This is useful to show MSTPCR bits on SuperH Mobile processors.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This code makes sh7343 share the sh7722 clock code. Instead of just using
the good and very old sh7343 clock implmentation, switch to the new MSTPCR
enabled clock code. SIU clocks are disabled on sh7343 for now.

With this change all SuperH Mobile devices now use the same clock code.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Handle module stop clock bits in MSTPCRn through the clock framework.
The clocks are named after the bits in the data sheet. The association
between bit number and hardware block is processor specific.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Make use of arch_flags to simplify the SIU clock code.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds physically contiguous memory chunks to the UIO devices.
The same strategy can be used in the future for the CEU as well.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch exports the VPU, VEU(1) and VEU(2) blocks of the sh7366
to user space using the uio_pdrv_genirq platform driver.

While at it, fix up the VEU(2) interrupt vector.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch exports the VPU, VEU2H0 and VEU2H1 blocks of the sh7723
to user space using the uio_pdrv_genirq platform driver.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch exports the VPU and VEU blocks of the sh7722 to user space
using the uio_pdrv_genirq platform driver.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch exports the VPU and VEU blocks of the sh7343 to user space
using the uio_pdrv_genirq platform driver.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch is

By sh2
- Remove duplicate code
- Reduce stack usage
- Cleanup and little optimize

By sh2a
- Add missing handler(256 to 511)
- Use sh2a instructions handler
Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

updated the following codes for SH7343:
 - add register_intc_controller()
 - add EARLY_SCIF_CONSOLE_PORT
 - add define of CPG register
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds platform data for the single I2C channel on sh7366.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds platform data for the single I2C channel on sh7723.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds platform data for two I2C channels to the sh7343.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch is based on interrupt acknowledge code for external
interrupt sources on sh3 processors and adds on sh4a processors.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

- Add EtherC + PHY resource define.
Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch contains the following cleanups:
- make the following needlessly global code static:
  - cf-enabler.c: cf_init()
  - cpu/clock.c: __clk_enable()
  - cpu/clock.c: __clk_disable()
  - process_32.c: default_idle()
  - time_32.c: struct clocksource_sh
  - timers/timer-tmu.c: struct tmu_timer_ops
- remove the following unused functions (no CONFIG_BLK_DEV_FD on sh):
  - process_{32,64}.c: disable_hlt()
  - process_{32,64}.c: enable_hlt()
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

SH7763 has 3 SCIF device. Current code supports SCIF0 and 1.
SCIF0 and 1 are same register constitution, but only SCIF2 is different.
I added support of SCIF2.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

SH7763's setup code use old DECLARE_INTC_DESC.
There was a compile error because of this.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch fixes the following build error caused by
commit a1dc4b59
(sh: intc_sh5 depends on cayman board for IRQ priority table.):

<--  snip  -->

...
  CC      arch/sh/kernel/cpu/irq/intc-sh5.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/kernel/cpu/irq/intc-sh5.c: In function 'plat_irq_setup':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/kernel/cpu/irq/intc-sh5.c:257: error: expected declaration or statement at end of input
make[4]: *** [arch/sh/kernel/cpu/irq/intc-sh5.o] Error 1

<--  snip  -->
Reported-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This was copied over from the previous MobileR bits, which doesn't
apply to R2. The URAM block on R2 is recycled for the L2 instead.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds support for sh7723 silicon with a prr value of 0x51.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch fixes a VPU vector typo for sh7723. The correct value is 0x980,
the same as for sh7722.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The USBF function on sh7722 is currently not working with the m66592_udc
driver. The driver is using platform_get_resource_byname() so my commit
a0d29798 broke sh7722 support.

The long term fix is to replace platform_get_resource_byname() in the
driver with platform_get_resource(), but this helps until that happens.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

'ix' is unsigned but denormal_subf1() may return a negative int.
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Make sure register modifications stay atomic. Fixes processors with
shared priority register masking. Dual bitmap masking is unaffected.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The processor models sh7706, sh7707 and sh7709 don't support high
level trigger sense configuration. And the intc code looks like
crap these days so what's the difference.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Clean up the intc tables by removing unneeded #ifdefs. The vector
list is what selects which interrupt sources that should be added,
having unsupported bitfields listed is ok as long as the vector
is excluded from the list.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds interrupt acknowledge code for external interrupt
sources on sh3 processors. Only really required for edge triggered
interrupts, but we ack regardless of sense configuration.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>