Make pskb_expand_head() check ip_summed to make sure csum_start is really
csum_start and not csum before adjusting it.

This fixes a bug I encountered using a Sun Quad-Fast Ethernet card and VLANs.
On my configuration, the sunhme driver produces skbs with differing amounts
of headroom on receive depending on the packet size.  See line 2030 of
drivers/net/sunhme.c; packets smaller than RX_COPY_THRESHOLD have 52 bytes
of headroom but packets larger than that cutoff have only 20 bytes.

When these packets reach the VLAN driver, vlan_check_reorder_header()
calls skb_cow(), which, if the packet has less than NET_SKB_PAD (== 32) bytes
of headroom, uses pskb_expand_head() to make more.

Then, pskb_expand_head() needs to adjust a lot of offsets into the skb,
including csum_start.  Since csum_start is a union with csum, if the packet
has a valid csum value this will corrupt it, which was the effect I observed.
The sunhme hardware computes receive checksums, so the skbs would be created
by the driver with ip_summed == CHECKSUM_COMPLETE and a valid csum field, and
then pskb_expand_head() would corrupt the csum field, leading to an "hw csum
error" message later on, for example in icmp_rcv() for pings larger than the
sunhme RX_COPY_THRESHOLD.

On the basis of the comment at the beginning of include/linux/skbuff.h,
I believe that the csum_start skb field is only meaningful if ip_csummed is
CSUM_PARTIAL, so this patch makes pskb_expand_head() adjust it only in that
case to avoid corrupting a valid csum value.

Please see my more in-depth disucssion of tracking down this bug for
more details if you like:

http://puellavulnerata.livejournal.com/112186.html
http://puellavulnerata.livejournal.com/112567.html
http://puellavulnerata.livejournal.com/112891.html
http://puellavulnerata.livejournal.com/113096.html
http://puellavulnerata.livejournal.com/113591.html

I am not subscribed to this list, so please CC me on replies.
Signed-off-by: NAndrea Shepard <andrea@persephoneslair.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mark Wagner reported OOM symptoms when sending UDP traffic over
a macvtap link to a kvm receiver.

This appears to be caused by the fact that macvtap packet queues
are unlimited in length.  This means that if the receiver can't
keep up with the rate of flow, then we will hit OOM. Of course
it gets worse if the OOM killer then decides to kill the receiver.

This patch imposes a cap on the packet queue length, in the same
way as the tuntap driver, using the device TX queue length.

Please note that macvtap currently has no way of giving congestion
notification, that means the software device TX queue cannot be
used and packets will always be dropped once the macvtap driver
queue fills up.

This shouldn't be a great problem for the scenario where macvtap
is used to feed a kvm receiver, as the traffic is most likely
external in origin so congestion notification can't be applied
anyway.

Of course, if anybody decides to complain about guest-to-guest
UDP packet loss down the track, then we may have to revisit this.

Incidentally, this patch also fixes a real memory leak when
macvtap_get_queue fails.

Chris Wright noticed that for this patch to work, we need a
non-zero TX queue length.  This patch includes his work to change
the default macvtap TX queue length to 500.
Reported-by: NMark Wagner <mwagner@redhat.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Acked-by: NChris Wright <chrisw@sous-sol.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some ixgbe cards put an invalid VF device ID in the PCIe SR-IOV
capability.  The ixgbe driver is only valid for PFs or non SR-IOV
hardware.  It seems that the same problem could occur on igb hardware as
well, so if we discover we are trying to initialize a VF in ixbge_probe
or igb_probe, print an error and exit.

Based on a patch for ixgbe from Chris Wright <chrisw@sous-sol.org>.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Cc: Chris Wright <chrisw@sous-sol.org>
Acked-by: NChris Wright <chrisw@sous-sol.org>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Advance a module version to 1.52.53-2.
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bug fix: Protect statistics ramrod sending code and a statistics counter update
with a spinlock. Otherwise there was a race condition that would allow sending
a statistics ramrods with the same sequence number or with sequence numbers not
in a natural order, which would cause a FW assert.
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bug fix: Protect the statistics state machine state update with a
spinlock.  Otherwise there was a race condition that would cause the
statistics to stay enabled despite the fact that they were disabled in
the LINK_DOWN event handler.
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new netpoll code in bridging contains use-after-free bugs
that are non-trivial to fix.

This patch fixes this by removing the code that uses skbs after
they're freed.

As a consequence, this means that we can no longer call bridge
from the netpoll path, so this patch also removes the controller
function in order to disable netpoll.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Thanks,
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It can happen that there are no packets in queue while calling
tcp_xmit_retransmit_queue(). tcp_write_queue_head() then returns
NULL and that gets deref'ed to get sacked into a local var.

There is no work to do if no packets are outstanding so we just
exit early.

This oops was introduced by 08ebd172 (tcp: remove tp->lost_out
guard to make joining diff nicer).
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Reported-by: NLennart Schulte <lennart.schulte@nets.rwth-aachen.de>
Tested-by: NLennart Schulte <lennart.schulte@nets.rwth-aachen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The input handler for Type 2 Routing Header (mip6_rthdr_input())
checks if the CoA in the packet matches the CoA in the XFRM state.

Current check is buggy: it compares the adddress in the Type 2
Routing Header, i.e. the HoA, against the expected CoA in the state.
The comparison should be made against the address in the destination
field of the IPv6 header.

The bug remained unnoticed because the main (and possibly only current)
user of the code (UMIP MIPv6 Daemon) initializes the XFRM state with the
unspecified address, i.e. explicitly allows everything.

Yoshifuji-san, can you ack that one?
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The order of freeing the IRQ and freeing the device in firmware
in ibmveth_close can cause the adapter to become unusable after a
subsequent ibmveth_open.  Only a reboot of the OS will make the
network device usable again. This is seen when cycling the adapter
up and down while there is network activity.

There is a window where an IRQ will be left unserviced (H_EOI will not
be called).  The solution is to make a VIO_IRQ_DISABLE h_call, free the
device with firmware, and then call free_irq.
Signed-off-by: NRobert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rt2x00dev->intf_work workqueue is never initialized when a driver is
probed for a non-existent device (in this case rt2500usb). On such a
path we call rt2x00lib_remove_dev() to free any resources initialized
during the probe before we use INIT_WORK to initialize the workqueue.
This causes lockdep to get confused since the lock used in the workqueue
hasn't been initialized yet but is now being acquired during
cancel_work_sync() called by rt2x00lib_remove_dev().

Fix this by initializing the workqueue first before we attempt to probe
the device. This should make lockdep happy and avoid breaking any
assumptions about how the library cleans up after a probe fails.

phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 2027, comm: modprobe Not tainted 2.6.35-rc5+ #60
Call Trace:
 [<ffffffff8105fe59>] register_lock_class+0x152/0x31f
 [<ffffffff81344a00>] ? usb_control_msg+0xd5/0x111
 [<ffffffff81061bde>] __lock_acquire+0xce/0xcf4
 [<ffffffff8105f6fd>] ? trace_hardirqs_off+0xd/0xf
 [<ffffffff81492aef>] ?  _raw_spin_unlock_irqrestore+0x33/0x41
 [<ffffffff810628d5>] lock_acquire+0xd1/0xf7
 [<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e
 [<ffffffff8104f06e>] __cancel_work_timer+0xd0/0x17e
 [<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e
 [<ffffffff8104f136>] cancel_work_sync+0xb/0xd
 [<ffffffffa0096675>] rt2x00lib_remove_dev+0x25/0xb0 [rt2x00lib]
 [<ffffffffa0096bf7>] rt2x00lib_probe_dev+0x380/0x3ed [rt2x00lib]
 [<ffffffff811d78a7>] ? __raw_spin_lock_init+0x31/0x52
 [<ffffffffa00bbd2c>] ? T.676+0xe/0x10 [rt2x00usb]
 [<ffffffffa00bbe4f>] rt2x00usb_probe+0x121/0x15e [rt2x00usb]
 [<ffffffff813468bd>] usb_probe_interface+0x151/0x19e
 [<ffffffff812ea08e>] driver_probe_device+0xa7/0x136
 [<ffffffff812ea167>] __driver_attach+0x4a/0x66
 [<ffffffff812ea11d>] ? __driver_attach+0x0/0x66
 [<ffffffff812e96ca>] bus_for_each_dev+0x54/0x89
 [<ffffffff812e9efd>] driver_attach+0x19/0x1b
 [<ffffffff812e9b64>] bus_add_driver+0xb4/0x204
 [<ffffffff812ea41b>] driver_register+0x98/0x109
 [<ffffffff813465dd>] usb_register_driver+0xb2/0x173
 [<ffffffffa00ca000>] ? rt2500usb_init+0x0/0x20 [rt2500usb]
 [<ffffffffa00ca01e>] rt2500usb_init+0x1e/0x20 [rt2500usb]
 [<ffffffff81000203>] do_one_initcall+0x6d/0x17a
 [<ffffffff8106cae8>] sys_init_module+0x9c/0x1e0
 [<ffffffff8100296b>] system_call_fastpath+0x16/0x1b
Signed-off-by: NStephen Boyd <bebarino@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Guest can trigger packet truncation by posting
a very short buffer and disabling buffer merging.
Convert pr_err to pr_debug to avoid log from filling
up when this happens.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

This was detected using two mcast router tables.  The
pimreg for the second interface did not have a specific
mrule, so packets received by it were handled by the
default table, which had nothing configured.

This caused the ipmr_fib_lookup to fail, causing
the memory leak.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We flush under vq mutex when changing backends.
This creates a deadlock as workqueue being flushed
needs this lock as well.

https://bugzilla.redhat.com/show_bug.cgi?id=612421

Drop the vq mutex before flush: we have the device mutex
which is sufficient to prevent another ioctl from touching
the vq.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Fix problem in reading the tx_queue recorded in a socket.  In
dev_pick_tx, the TX queue is read by doing a check with
sk_tx_queue_recorded on the socket, followed by a sk_tx_queue_get.
The problem is that there is not mutual exclusion across these
calls in the socket so it it is possible that the queue in the
sock can be invalidated after sk_tx_queue_recorded is called so
that sk_tx_queue get returns -1, which sets 65535 in queue_index
and thus dev_pick_tx returns 65536 which is a bogus queue and
can cause crash in dev_queue_xmit.

We fix this by only calling sk_tx_queue_get which does the proper
checks.  The interface is that sk_tx_queue_get returns the TX queue
if the sock argument is non-NULL and TX queue is recorded, else it
returns -1.  sk_tx_queue_recorded is no longer used so it can be
completely removed.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When configuring DMVPN (GRE + openNHRP) and a GRE remote
address is configured a kernel Oops is observed.  The
obserseved Oops is caused by a NULL header_ops pointer
(neigh->dev->header_ops) in neigh_update_hhs() when

void (*update)(struct hh_cache*, const struct net_device*, const unsigned char *)
= neigh->dev->header_ops->cache_update;

is executed.  The dev associated with the NULL header_ops is
the GRE interface.  This patch guards against the
possibility that header_ops is NULL.

This Oops was first observed in kernel version 2.6.26.8.
Signed-off-by: NDoug Kehn <rdkehn@yahoo.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit fc6055a5 (net: Introduce skb_orphan_try()) added early
orphaning of skbs.

This unfortunately added a performance regression in skb_tx_hash() in
case of stacked devices (bonding, vlans, ...)

Since skb->sk is now NULL, we cannot access sk->sk_hash anymore to
spread tx packets to multiple NIC queues on multiqueue devices.

skb_tx_hash() in this case only uses skb->protocol, same value for all
flows.

skb_orphan_try() can copy sk->sk_hash into skb->rxhash and skb_tx_hash()
can use this saved sk_hash value to compute its internal hash value.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rfs: call sock_rps_record_flow() in tcp_splice_read()

call sock_rps_record_flow() in tcp_splice_read(), so the applications using
splice(2) or sendfile(2) can utilize RFS.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
----
 net/ipv4/tcp.c |    1 +
 1 file changed, 1 insertion(+)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

xfrm_resolve_and_create_bundle() assumed that, if policies indicated
presence of xfrms, bundle template resolution would always return
some xfrms. This is not true for 'use' level policies which can
result in no xfrm's being applied if there is no suitable xfrm states.
This fixes a crash by this incorrect assumption.
Reported-by: NGeorge Spelvin <linux@horizon.com>
Bisected-by: NGeorge Spelvin <linux@horizon.com>
Tested-by: NGeorge Spelvin <linux@horizon.com>
Signed-off-by: NTimo Teräs <timo.teras@iki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"hostap: Protect against initialization interrupt" (which reinstated
"wireless: hostap, fix oops due to early probing interrupt")
reintroduced Bug 16111.  This is because hostap_pci wasn't setting
dev->base_addr, which is now checked in prism2_interrupt.  As a result,
initialization was failing for PCI-based hostap devices.  This corrects
that oversight.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use spin_lock_irqsave instead of spin_lock in ax_interrupt because
the interrupt handler can also be invoked from ei_watchdog.
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based upon a report by Randy Dunlap.

DSA needs PHYLIB, but PHYLIB needs NET_ETHERNET.  So, in order
to select PHYLIB we have to make DSA depend upon NET_ETHERNET.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

not all of the ICMP packets need an IP header payload, so we check the length
of the skbs only when the packets should have an IP header payload.

Based upon analysis and initial patch by Rodrigo Partearroyo González.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
----
 net/sched/act_nat.c |    5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge error.

See CFG_METHOD_8 (0x3c800000 + 0x00300000) since version 8.002.00
of Realtek's driver.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update auth level for already existing connections if it is lower
than required by new connection.
Signed-off-by: NVille Tervo <ville.tervo@nokia.com>
Reviewed-by: NEmeltchenko Andrei <andrei.emeltchenko@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When authentication fails for a connection the assumed security level
should be set back to BT_SECURITY_LOW so that subsequent connect
attempts over the same link don't falsely assume that security is
adequate enough.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Due to race condition in L2CAP state machine L2CAP Connection Request
may be sent twice for SDP with the same source channel id. Problems
reported connecting to Apple products, some carkit, Blackberry phones.

...
2010-06-07 21:18:03.651031 < ACL data: handle 1 flags 0x02 dlen 12
    L2CAP(s): Connect req: psm 1 scid 0x0040
2010-06-07 21:18:03.653473 > HCI Event: Number of Completed Packets (0x13) plen 5
    handle 1 packets 1
2010-06-07 21:18:03.653808 > HCI Event: Auth Complete (0x06) plen 3
    status 0x00 handle 1
2010-06-07 21:18:03.653869 < ACL data: handle 1 flags 0x02 dlen 12
    L2CAP(s): Connect req: psm 1 scid 0x0040
...

Patch uses L2CAP_CONF_CONNECT_PEND flag to mark that L2CAP Connection
Request has been sent already.

Modified version of patch from Ville Tervo.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/sb1250-mac.c |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original KERN_CRIT will mess up terminals.

CC: Sreenivasa Honnur <Sreenivasa.Honnur@neterion.com>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix missing iounmaps.
Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bridge protocol lives dangerously by having incestuous relations
with the IP stack.  In this instance an abomination has been created
where a bogus IPCB area from a bridged packet leads to a crash in
the IP stack because it's interpreted as IP options.

This patch papers over the problem by clearing the IPCB area in that
particular spot.  To fix this properly we'd also need to parse any
IP options if present but I'm way too lazy for that.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Cheers,
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Failure cases within ath9k_hif_usb_alloc_urbs are failed
to release allocated memory.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On Tue, Jul 06, 2010 at 08:48:35AM +0800, Herbert Xu wrote:
>
> bridge: Restore NULL check in br_mdb_ip_get

Resend with proper attribution.

bridge: Restore NULL check in br_mdb_ip_get

Somewhere along the line the NULL check in br_mdb_ip_get went
AWOL, causing crashes when we receive an IGMP packet with no
multicast table allocated.

This patch restores it and ensures all br_mdb_*_get functions
use it.
Reported-by: NFrank Arnold <frank.arnold@amd.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Thanks,
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netif_vdbg() was originally defined as entirely equivalent to
netdev_vdbg(), but I assume that it was intended to take the same
parameters as netif_dbg() etc.  (Currently it is only used by the
sfc driver, in which I worked on that assumption.)

In commit a4ed89cb I changed the definition used when VERBOSE_DEBUG is
not defined, but I failed to notice that the definition used when
VERBOSE_DEBUG is defined was also not as I expected.  Change that to
match netif_dbg() as well.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net_device allocated with alloc_eip_netdev() must be freed.
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While using xfrm by MARK feature in
2.6.34 - 2.6.35 kernels, the mark
is always cleared in flowi structure via memset in
_decode_session4 (net/ipv4/xfrm4_policy.c), so
the policy lookup fails.
IPv6 code is affected by this bug too.
Signed-off-by: NPeter Kosyh <p.kosyh@gmail.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>