We expect to have firmware-first handling of RAS SErrors, with errors
notified via an APEI method. For systems without firmware-first, add
some minimal handling to KVM.

There are two ways KVM can take an SError due to a guest, either may be a
RAS error: we exit the guest due to an SError routed to EL2 by HCR_EL2.AMO,
or we take an SError from EL2 when we unmask PSTATE.A from __guest_exit.

The current SError from EL2 code unmasks SError and tries to fence any
pending SError into a single instruction window. It then leaves SError
unmasked.

With the v8.2 RAS Extensions we may take an SError for a 'corrected'
error, but KVM is only able to handle SError from EL2 if they occur
during this single instruction window...

The RAS Extensions give us a new instruction to synchronise and
consume SErrors. The RAS Extensions document (ARM DDI0587),
'2.4.1 ESB and Unrecoverable errors' describes ESB as synchronising
SError interrupts generated by 'instructions, translation table walks,
hardware updates to the translation tables, and instruction fetches on
the same PE'. This makes ESB equivalent to KVMs existing
'dsb, mrs-daifclr, isb' sequence.

Use the alternatives to synchronise and consume any SError using ESB
instead of unmasking and taking the SError. Set ARM_EXIT_WITH_SERROR_BIT
in the exit_code so that we can restart the vcpu if it turns out this
SError has no impact on the vcpu.
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

We expect to have firmware-first handling of RAS SErrors, with errors
notified via an APEI method. For systems without firmware-first, add
some minimal handling to KVM.

There are two ways KVM can take an SError due to a guest, either may be a
RAS error: we exit the guest due to an SError routed to EL2 by HCR_EL2.AMO,
or we take an SError from EL2 when we unmask PSTATE.A from __guest_exit.

For SError that interrupt a guest and are routed to EL2 the existing
behaviour is to inject an impdef SError into the guest.

Add code to handle RAS SError based on the ESR. For uncontained and
uncategorized errors arm64_is_fatal_ras_serror() will panic(), these
errors compromise the host too. All other error types are contained:
For the fatal errors the vCPU can't make progress, so we inject a virtual
SError. We ignore contained errors where we can make progress as if
we're lucky, we may not hit them again.

If only some of the CPUs support RAS the guest will see the cpufeature
sanitised version of the id registers, but we may still take RAS SError
on this CPU. Move the SError handling out of handle_exit() into a new
handler that runs before we can be preempted. This allows us to use
this_cpu_has_cap(), via arm64_is_ras_serror().
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

When we exit a guest due to an SError the vcpu fault info isn't updated
with the ESR. Today this is only done for traps.

The v8.2 RAS Extensions define ISS values for SError. Update the vcpu's
fault_info with the ESR on SError so that handle_exit() can determine
if this was a RAS SError and decode its severity.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

If we deliver a virtual SError to the guest, the guest may defer it
with an ESB instruction. The guest reads the deferred value via DISR_EL1,
but the guests view of DISR_EL1 is re-mapped to VDISR_EL2 when HCR_EL2.AMO
is set.

Add the KVM code to save/restore VDISR_EL2, and make it accessible to
userspace as DISR_EL1.
Signed-off-by: NJames Morse <james.morse@arm.com>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Prior to v8.2's RAS Extensions, the HCR_EL2.VSE 'virtual SError' feature
generated an SError with an implementation defined ESR_EL1.ISS, because we
had no mechanism to specify the ESR value.

On Juno this generates an all-zero ESR, the most significant bit 'ISV'
is clear indicating the remainder of the ISS field is invalid.

With the RAS Extensions we have a mechanism to specify this value, and the
most significant bit has a new meaning: 'IDS - Implementation Defined
Syndrome'. An all-zero SError ESR now means: 'RAS error: Uncategorized'
instead of 'no valid ISS'.

Add KVM support for the VSESR_EL2 register to specify an ESR value when
HCR_EL2.VSE generates a virtual SError. Change kvm_inject_vabt() to
specify an implementation-defined value.

We only need to restore the VSESR_EL2 value when HCR_EL2.VSE is set, KVM
save/restores this bit during __{,de}activate_traps() and hardware clears the
bit once the guest has consumed the virtual-SError.

Future patches may add an API (or KVM CAP) to pend a virtual SError with
a specified ESR.

Cc: Dongjiu Geng <gengdongjiu@huawei.com>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJames Morse <james.morse@arm.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Non-VHE systems take an exception to EL2 in order to world-switch into the
guest. When returning from the guest KVM implicitly restores the DAIF
flags when it returns to the kernel at EL1.

With VHE none of this exception-level jumping happens, so KVMs
world-switch code is exposed to the host kernel's DAIF values, and KVM
spills the guest-exit DAIF values back into the host kernel.
On entry to a guest we have Debug and SError exceptions unmasked, KVM
has switched VBAR but isn't prepared to handle these. On guest exit
Debug exceptions are left disabled once we return to the host and will
stay this way until we enter user space.

Add a helper to mask/unmask DAIF around VHE guests. The unmask can only
happen after the hosts VBAR value has been synchronised by the isb in
__vhe_hyp_call (via kvm_call_hyp()). Masking could be as late as
setting KVMs VBAR value, but is kept here for symmetry.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJames Morse <james.morse@arm.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

KVM would like to consume any pending SError (or RAS error) after guest
exit. Today it has to unmask SError and use dsb+isb to synchronise the
CPU. With the RAS extensions we can use ESB to synchronise any pending
SError.

Add the necessary macros to allow DISR to be read and converted to an
ESR.

We clear the DISR register when we enable the RAS cpufeature, and the
kernel has not executed any ESB instructions. Any value we find in DISR
must have belonged to firmware. Executing an ESB instruction is the
only way to update DISR, so we can expect firmware to have handled
any deferred SError. By the same logic we clear DISR in the idle path.
Reviewed-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NJames Morse <james.morse@arm.com>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

ARM v8.2 has a feature to add implicit error synchronization barriers
whenever the CPU enters or returns from an exception level. Add this to the
features we always enable. CPUs that don't support this feature will treat
the bit as RES0.

This feature causes RAS errors that are not yet visible to software to
become pending SErrors. We expect to have firmware-first RAS support
so synchronised RAS errors will be take immediately to EL3.
Any system without firmware-first handling of errors will take the SError
either immediatly after exception return, or when we unmask SError after
entry.S's work.

Adding IESB to the ELx flags causes it to be enabled by KVM and kexec
too.

Platform level RAS support may require additional firmware support.

Cc: Christoffer Dall <christoffer.dall@linaro.org>
Suggested-by: NWill Deacon <will.deacon@arm.com>
Link: https://www.spinics.net/lists/kvm-arm/msg28192.htmlAcked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Prior to v8.2, SError is an uncontainable fatal exception. The v8.2 RAS
extensions use SError to notify software about RAS errors, these can be
contained by the Error Syncronization Barrier.

An ACPI system with firmware-first may use SError as its 'SEI'
notification. Future patches may add code to 'claim' this SError as a
notification.

Other systems can distinguish these RAS errors from the SError ESR and
use the AET bits and additional data from RAS-Error registers to handle
the error. Future patches may add this kernel-first handling.

Without support for either of these we will panic(), even if we received
a corrected error. Add code to decode the severity of RAS errors. We can
safely ignore contained errors where the CPU can continue to make
progress. For all other errors we continue to panic().
Signed-off-by: NJames Morse <james.morse@arm.com>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

ARM's v8.2 Extentions add support for Reliability, Availability and
Serviceability (RAS). On CPUs with these extensions system software
can use additional barriers to isolate errors and determine if faults
are pending. Add cpufeature detection.

Platform level RAS support may require additional firmware support.
Reviewed-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NXie XiuQi <xiexiuqi@huawei.com>
[Rebased added config option, reworded commit message]
Signed-off-by: NJames Morse <james.morse@arm.com>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

__cpu_setup() configures SCTLR_EL1 using some hard coded hex masks,
and el2_setup() duplicates some this when setting RES1 bits.

Lets make this the same as KVM's hyp_init, which uses named bits.

First, we add definitions for all the SCTLR_EL{1,2} bits, the RES{1,0}
bits, and those we want to set or clear.

Add a build_bug checks to ensures all bits are either set or clear.
This means we don't need to preserve endian-ness configuration
generated elsewhere.

Finally, move the head.S and proc.S users of these hard-coded masks
over to the macro versions.
Signed-off-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

this_cpu_has_cap() tests caps->desc not caps->matches, so it stops
walking the list when it finds a 'silent' feature, instead of
walking to the end of the list.

Prior to v4.6's 644c2ae1 ("arm64: cpufeature: Test 'matches' pointer
to find the end of the list") we always tested desc to find the end of
a capability list. This was changed for dubious things like PAN_NOT_UAO.
v4.7's e3661b12 ("arm64: Allow a capability to be checked on
single CPU") added this_cpu_has_cap() using the old desc style test.

CC: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

When refactoring the sigreturn code to handle SVE, I changed the
sigreturn implementation to store the new FPSIMD state from the
user sigframe into task_struct before reloading the state into the
CPU regs.  This makes it easier to convert the data for SVE when
needed.

However, it turns out that the fpsimd_state structure passed into
fpsimd_update_current_state is not fully initialised, so assigning
the structure as a whole corrupts current->thread.fpsimd_state.cpu
with uninitialised data.

This means that if the garbage data written to .cpu happens to be a
valid cpu number, and the task is subsequently migrated to the cpu
identified by the that number, and then tries to enter userspace,
the CPU FPSIMD regs will be assumed to be correct for the task and
not reloaded as they should be.  This can result in returning to
userspace with the FPSIMD registers containing data that is stale or
that belongs to another task or to the kernel.

Knowingly handing around a kernel structure that is incompletely
initialised with user data is a potential source of mistakes,
especially across source file boundaries.  To help avoid a repeat
of this issue, this patch adapts the relevant internal API to hand
around the user-accessible subset only: struct user_fpsimd_state.

To avoid future surprises, this patch also converts all uses of
struct fpsimd_state that really only access the user subset, to use
struct user_fpsimd_state.  A few missing consts are added to
function prototypes for good measure.

Thanks to Will for spotting the cause of the bug here.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDave Martin <Dave.Martin@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The PUD macros (PUD_TABLE_BIT, PUD_TYPE_MASK, PUD_TYPE_SECT) use the
pgdval_t even when pudval_t is available. Even though the underlying
type for both (u64) is the same it is confusing and may lead to issues
in the future.

Fix this by using pudval_t to define the PUD_* macros.

Fixes: 084bd298 ("ARM64: mm: HugeTLB support.")
Fixes: 206a2a73 ("arm64: mm: Create gigabyte kernel logical mappings where possible")
Signed-off-by: NPunit Agrawal <punit.agrawal@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

It isn't entirely obvious if we're using software PAN because we
don't say anything about it in the boot log. But if we're using
hardware PAN we'll print a nice CPU feature message indicating
it. Add a print for software PAN too so we know if it's being
used or not.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The 'pos' argument is used to select where in TCR to write the value:
the IPS or PS bitfield.

Fixes: 787fd1d0 ("arm64: limit PA size to supported range")
Signed-off-by: NKristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Commit fa2a8445 incorrectly masks the index of the HYP ID map pgd
entry, causing a non-VHE kernel to hang during boot. This happens when
VA_BITS=48 and the ID map text is in 52-bit physical memory. In this
case we don't need an extra table level but need more entries in the
top-level table, so we need to map into hyp_pgd and need to use
__kvm_idmap_ptrs_per_pgd to mask in the extra bits. However,
__create_hyp_mappings currently masks by PTRS_PER_PGD instead.

Fix it so that we always use __kvm_idmap_ptrs_per_pgd for the HYP ID
map. This ensures that we use the larger mask for the top-level ID map
table when it has more entries. In all other cases, PTRS_PER_PGD is used
as normal.

Fixes: fa2a8445 ("arm64: allow ID map to be extended to 52 bits")
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NKristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Commit fa2a8445 added support for extending the ID map to 52 bits,
but accidentally dropped a required change to __cpu_uses_extended_idmap.
As a result, the kernel fails to boot when VA_BITS = 48 and the ID map
text is in 52-bit physical memory, because we reduce TCR.T0SZ to cover
the ID map, but then never set it back to VA_BITS.

Add back the change, and also clean up some double parentheses.

Fixes: fa2a8445 ("arm64: allow ID map to be extended to 52 bits")
Reviewed-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NKristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Printing kernel addresses should be done in limited circumstances, mostly
for debugging purposes. Printing out the virtual memory layout at every
kernel bootup doesn't really fall into this category so delete the prints.
There are other ways to get the same information.
Acked-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NLaura Abbott <labbott@redhat.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

In case of error, the function of_platform_device_create() returns
NULL pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.

Fixes: 677a60bd ("firmware: arm_sdei: Discover SDEI support via ACPI")
Acked-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

We set dsu_pmu->num_counters to -1, when the DSU is allocated
but not initialised when none of the CPUs are active in the DSU.
However, we use an unsigned field for num_counters. Switch this
to a signed field.

Fixes: 7520fa99 ("perf: ARM DynamIQ Shared Unit PMU support")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Sometimes a single capability could be listed multiple times with
differing matches(), e.g, CPU errata for different MIDR versions.
This breaks verify_local_cpu_feature() and this_cpu_has_cap() as
we stop checking for a capability on a CPU with the first
entry in the given table, which is not sufficient. Make sure we
run the checks for all entries of the same capability. We do
this by fixing __this_cpu_has_cap() to run through all the
entries in the given table for a match and reuse it for
verify_local_cpu_feature().

Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The Kryo CPUs are also affected by the Falkor 1003 errata, so
we need to do the same workaround on Kryo CPUs. The MIDR is
slightly more complicated here, where the PART number is not
always the same when looking at all the bits from 15 to 4. Drop
the lower 8 bits and just look at the top 4 to see if it's '2'
and then consider those as Kryo CPUs. This covers all the
combinations without having to list them all out.

Fixes: 38fd94b0 ("arm64: Work around Falkor erratum 1003")
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Currently the early assembler page table code assumes that precisely
1xpgd, 1xpud, 1xpmd are sufficient to represent the early kernel text
mappings.

Unfortunately this is rarely the case when running with a 16KB granule,
and we also run into limits with 4KB granule when building much larger
kernels.

This patch re-writes the early page table logic to compute indices of
mappings for each level of page table, and if multiple indices are
required, the next-level page table is scaled up accordingly.

Also the required size of the swapper_pg_dir is computed at link time
to cover the mapping [KIMAGE_ADDR + VOFFSET, _end]. When KASLR is
enabled, an extra page is set aside for each level that may require extra
entries at runtime.
Tested-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NSteve Capper <steve.capper@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The trampoline page tables are positioned after the early page tables in
the kernel linker script.

As we are about to change the early page table logic to resolve the
swapper size at link time as opposed to compile time, the
SWAPPER_DIR_SIZE variable (currently used to locate the trampline)
will be rendered unsuitable for low level assembler.

This patch solves this issue by moving the trampoline before the PAN
page tables. The offset to the trampoline from ttbr1 can then be
expressed by: PAGE_SIZE + RESERVED_TTBR0_SIZE, which is available to the
entry assembler.
Tested-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NSteve Capper <steve.capper@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Currently one resolves the location of the reserved_ttbr0 for PAN by
taking a positive offset from swapper_pg_dir. In a future patch we wish
to extend the swapper s.t. its size is determined at link time rather
than comile time, rendering SWAPPER_DIR_SIZE unsuitable for such a low
level calculation.

In this patch we re-arrange the order of the linker script s.t. instead
one computes reserved_ttbr0 by subtracting RESERVED_TTBR0_SIZE from
swapper_pg_dir.
Tested-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NSteve Capper <steve.capper@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

When CONFIG_UNMAP_KERNEL_AT_EL0 is set the SDEI entry point and the rest
of the kernel may be unmapped when we take an event. If this may be the
case, use an entry trampoline that can switch to the kernel page tables.

We can't use the provided PSTATE to determine whether to switch page
tables as we may have interrupted the kernel's entry trampoline, (or a
normal-priority event that interrupted the kernel's entry trampoline).
Instead test for a user ASID in ttbr1_el1.

Save a value in regs->addr_limit to indicate whether we need to restore
the original ASID when returning from this event. This value is only used
by do_page_fault(), which we don't call with the SDEI regs.
Signed-off-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

SDEI needs to calculate an offset in the trampoline page too. Move
the extern char[] to sections.h.

This patch just moves code around.
Signed-off-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

SDEI defines a new ACPI table to indicate the presence of the interface.
The conduit is discovered in the same way as PSCI.

For ACPI we need to create the platform device ourselves as SDEI doesn't
have an entry in the DSDT.

The SDEI platform device should be created after ACPI has been initialised
so that we can parse the table, but before GHES devices are created, which
may register SDE events if they use SDEI as their notification type.
Reviewed-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NJames Morse <james.morse@arm.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

SDEI inherits the 'use hvc' bit that is also used by PSCI. PSCI does all
its initialisation early, SDEI does its late.

Remove the __init annotation from acpi_psci_use_hvc().
Acked-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NJames Morse <james.morse@arm.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Private SDE events are per-cpu, and need to be registered and enabled
on each CPU.

Hide this detail from the caller by adapting our {,un}register and
{en,dis}able calls to send an IPI to each CPU if the event is private.

CPU private events are unregistered when the CPU is powered-off, and
re-registered when the CPU is brought back online. This saves bringing
secondary cores back online to call private_reset() on shutdown, kexec
and resume from hibernate.
Signed-off-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

When a CPU enters an idle lower-power state or is powering off, we
need to mask SDE events so that no events can be delivered while we
are messing with the MMU as the registered entry points won't be valid.

If the system reboots, we want to unregister all events and mask the CPUs.
For kexec this allows us to hand a clean slate to the next kernel
instead of relying on it to call sdei_{private,system}_data_reset().

For hibernate we unregister all events and re-register them on restore,
in case we restored with the SDE code loaded at a different address.
(e.g. KASLR).

Add all the notifiers necessary to do this. We only support shared events
so all events are left registered and enabled over CPU hotplug.
Reviewed-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NJames Morse <james.morse@arm.com>
[catalin.marinas@arm.com: added CPU_PM_ENTER_FAILED case]
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The Software Delegated Exception Interface (SDEI) is an ARM standard
for registering callbacks from the platform firmware into the OS.
This is typically used to implement RAS notifications.

Such notifications enter the kernel at the registered entry-point
with the register values of the interrupted CPU context. Because this
is not a CPU exception, it cannot reuse the existing entry code.
(crucially we don't implicitly know which exception level we interrupted),

Add the entry point to entry.S to set us up for calling into C code. If
the event interrupted code that had interrupts masked, we always return
to that location. Otherwise we pretend this was an IRQ, and use SDEI's
complete_and_resume call to return to vbar_el1 + offset.

This allows the kernel to deliver signals to user space processes. For
KVM this triggers the world switch, a quick spin round vcpu_run, then
back into the guest, unless there are pending signals.

Add sdei_mask_local_cpu() calls to the smp_send_stop() code, this covers
the panic() code-path, which doesn't invoke cpuhotplug notifiers.

Because we can interrupt entry-from/exit-to another EL, we can't trust the
value in sp_el0 or x29, even if we interrupted the kernel, in this case
the code in entry.S will save/restore sp_el0 and use the value in
__entry_task.

When we have VMAP stacks we can interrupt the stack-overflow test, which
stirs x0 into sp, meaning we have to have our own VMAP stacks. For now
these are allocated when we probe the interface. Future patches will add
refcounting hooks to allow the arch code to allocate them lazily.
Signed-off-by: NJames Morse <james.morse@arm.com>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Add __uaccess_{en,dis}able_hw_pan() helpers to set/clear the PSTATE.PAN
bit.
Signed-off-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Today the arm64 arch code allocates an extra IRQ stack per-cpu. If we
also have SDEI and VMAP stacks we need two extra per-cpu VMAP stacks.

Move the VMAP stack allocation out to a helper in a new header file.
This avoids missing THREADINFO_GFP, or getting the all-important alignment
wrong.
Signed-off-by: NJames Morse <james.morse@arm.com>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Reviewed-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The Software Delegated Exception Interface (SDEI) is an ARM standard
for registering callbacks from the platform firmware into the OS.
This is typically used to implement firmware notifications (such as
firmware-first RAS) or promote an IRQ that has been promoted to a
firmware-assisted NMI.

Add the code for detecting the SDEI version and the framework for
registering and unregistering events. Subsequent patches will add the
arch-specific backend code and the necessary power management hooks.

Only shared events are supported, power management, private events and
discovery for ACPI systems will be added by later patches.
Signed-off-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The Software Delegated Exception Interface (SDEI) is an ARM standard
for registering callbacks from the platform firmware into the OS.
This is typically used to implement RAS notifications, or from an
IRQ that has been promoted to a firmware-assisted NMI.

Add a new devicetree binding to describe the SDE firmware interface.
Signed-off-by: NJames Morse <james.morse@arm.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Now that a VHE host uses tpidr_el2 for the cpu offset we no longer
need KVM to save/restore tpidr_el1. Move this from the 'common' code
into the non-vhe code. While we're at it, on VHE we don't need to
save the ELR or SPSR as kernel_entry in entry.S will have pushed these
onto the kernel stack, and will restore them from there. Move these
to the non-vhe code as we need them to get back to the host.

Finally remove the always-copy-tpidr we hid in the stage2 setup
code, cpufeature's enable callback will do this for VHE, we only
need KVM to do it for non-vhe. Add the copy into kvm-init instead.
Signed-off-by: NJames Morse <james.morse@arm.com>
Reviewed-by: NChristoffer Dall <cdall@linaro.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Now that KVM uses tpidr_el2 in the same way as Linux's cpu_offset in
tpidr_el1, merge the two. This saves KVM from save/restoring tpidr_el1
on VHE hosts, and allows future code to blindly access per-cpu variables
without triggering world-switch.
Signed-off-by: NJames Morse <james.morse@arm.com>
Reviewed-by: NChristoffer Dall <cdall@linaro.org>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Make tpidr_el2 a cpu-offset for per-cpu variables in the same way the
host uses tpidr_el1. This lets tpidr_el{1,2} have the same value, and
on VHE they can be the same register.

KVM calls hyp_panic() when anything unexpected happens. This may occur
while a guest owns the EL1 registers. KVM stashes the vcpu pointer in
tpidr_el2, which it uses to find the host context in order to restore
the host EL1 registers before parachuting into the host's panic().

The host context is a struct kvm_cpu_context allocated in the per-cpu
area, and mapped to hyp. Given the per-cpu offset for this CPU, this is
easy to find. Change hyp_panic() to take a pointer to the
struct kvm_cpu_context. Wrap these calls with an asm function that
retrieves the struct kvm_cpu_context from the host's per-cpu area.

Copy the per-cpu offset from the hosts tpidr_el1 into tpidr_el2 during
kvm init. (Later patches will make this unnecessary for VHE hosts)

We print out the vcpu pointer as part of the panic message. Add a back
reference to the 'running vcpu' in the host cpu context to preserve this.
Signed-off-by: NJames Morse <james.morse@arm.com>
Reviewed-by: NChristoffer Dall <cdall@linaro.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>