Currently the firmware is handling this, but that is wrong as it then
needs to assume a certain command queue, therefore this should be in
the driver; add it here so it can be removed from the firmware in the
future.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently a valid sta_id is assumed to mean that the queue is
meant to also be aggregated, but that assumption will not be
true in the future, so don't make it in the lower level but
only in the inline wrapper.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In a later patch, the hardware configuration will be moved to
firmware. Prepare for this by allowing hardware configuration
in the transport to be skipped by not passing a configuration
on enable and passing configure_scd=false on disable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The tracepoints that are only used in code linked with iwlwifi.ko,
as are the tracepoints, don't need to be exported, so don't.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to follow more easily what's going on, add some
debug statements to the quota allocation algorithm.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enable fragmented scan that was diabled due to a FW bug.
New fixed FWs use a TLV bit to advertise fragmented scan support.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of having all arguments passed to the function,
add a struct to hold them and only pass some directly.

This will make future work in this area cleaner.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Configuring the hw scheduler during queue enablement is done by
writing the appropriate values to the scheduler peripherals, and
it is essentially the same for all buses.

Whenever writing is done via the standard iwl_write_prph, we can
avoid duplicating the code for each bus. Those operations are
queue deactivation, RA/TID mapping, chain-building settings,
enabling/disabling aggregations and activating/deactivating the
TX FIFOs.

Consolidate this code using static inlines in a new header file.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Make sure that when running the TDLS discovery session
protection - the time event that ensures we remain on channel
has been scheduled and started running before leaving.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We need to disable PS when a monitor vif is active or, in the future,
when a channel switch is happening.  Add a boolean to mvmvif that
allows PS to be disabled generically.  Additionally, make the monitor
interface use this new flag when it gets activated.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a new iwl_mvm_power_update_ps() function that allows only ps to be
updated according to changes in the vifs.  This allows us to disable
ps only without affecting the pm values of the vifs (and to avoid
sending unnecessary MAC_PM_POWER_TABLE commands to the firmware).
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Separate the ps part of iwl_mvm_power_set_pm() into a new
iwl_mvm_power_set_ps() function.  This will enable us to update the ps
part independently from the rest, which is needed by CSA (at least).

This required a bit of refactoring and the creation of a new iterator
function.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If a monitor interface is added and then removed, we don't reset the
mvm->ps_disabled flag, so we never re-enable power saving.  Fix that
and rearrange the code a bit.

Additionally, fix a small indentation mistake in the
iwl_mvm_power_set_pm() function declaration.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If recovery happened after mvm entered d0i3 (e.g.
due to sysassert when releasing the bus), the
mvm->state wasn't cleared properly, causing the
ongoing recovery to fail (due to iwl_mvm_ref_sync
failure).

This in turn fails the ongoing recovery, and triggers
a reprobe, which terminates any ongoing wifi activity.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Aggregations hit latency so disable it by default on
low latency vifs for now. Enable control over this behavior and
allow control over the max frames in an AMPDU in low latency
vifs via debugfs.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to make debugging easier, add an entry to export the
ps_disabled value via debugfs.  To make usage of the
debugfs_create_*() function easier, change the ps_disabled element to
u8.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

With a significant number of deployed APs, enabling uAPSD leads to the
AP never using aggregation sessions (likely due to the complexities
involved in handling uAPSD in those.) This obviously results in a large
drop in throughput with such APs.

On the other hand, uAPSD can result in some power consumption benefits,
but for now just disable it to get performance with affected APs back
up.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

1. the base_address limitation was wrong, address can be bigger than
0x80C000
2. the ucode data_struct changed.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add Marker command.
The marker command send the ucode the time of sending the command in
milliseconds since 1970-01-01 00:00:00 UTC, in addition to other metatdata.
The ucode inserts this information into the usniffer logs, and returns the GP2
time stamp inside the command response.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If we're manually testing the CT kill functionality via debugfs, we
shouldn't schedule the work to recheck the temperature after the
ct_kill_duration period has passed.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Since we can't read the actual temperature when the firmware is
running, just set the temperature to 0 when the test is disabled and
disable CT Kill if it was enabled.

Additionally, since we rely on iwl_mvm_tt_handler() to exit CT kill
when in test mode, call iwl_mvm_exit_ctkill() in that function if the
temperature is low again.  Also make the iwl_mvm_enter_ctkill() and
iwl_mvm_exit_ctkill() return if called when not necessary anymore
(e.g. when iwl_mvm_exit_ctkill() is called when we're not in CT-kill).
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Performance is less an issue in P2P and reliability
is critical. Enable protection always for P2P.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

By default, when uapsd is not used, the ucode uses
null data packet to exit power-save and get then
pending frames.

However, some tests require the explicit usage of ps-poll.
Allow setting use_ps_poll power option (through debugfs)
to configure the ucode to use ps-poll instead.

The ucode configuration is done by setting the advanced-pm
flag while setting all the ACs to non-upasd mode.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to force the GO to use protection and enhances
the reliability of the link.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to leave a frame in the Tx Fifo which allows
the firmware to try to enter burst mode.
The end result of this is a better latency since the
firmware utilises the TxOP better.

Also limit the AMPDU size to the limit set in the ADDBA
response. This doesn't change much since the AMPDU size
was limited by the configuration of the hardware scheduler,
but here we add a software limit by the mean of the link
quality command.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add ability to set the NIC's temperature and ignore the actual temperature
that the FW supplies.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Pull networking fixes from David Miller:
 "Here are some bug fixes that have piled up during ksummit/linuxcon.

   1) Fix endian problems in ibmveth, from Anton Blanchard.

   2) IPV6 routing code does GFP_KERNEL allocation in atomic, fix from
      Benjamin Block.

   3) SCTP association fixes from Daniel Borkmann.

   4) When multiple VLAN headers are present we have to make sure the
      second and subsequent ones are pullable in the SKB otherwise we
      blindly dereference garbage.  From Jiri Benc.

   5) The argument adjustment of the signature of hlist_add_after*()
      introduced a regression in the batman-adv code, fix from Sven
      Eckelmann.

   6) Fix TX hang handling to avoid a panic in i40e, from Anjali Singhai
      Jain.

   7) PTP flag test is inverted in i40e driver, from Jesse Brandeburg.

   8) ATM LEC driver needs to hold RTNL mutex over MTU changes, from
      Chas Williams.

   9) Truncate packets larger then the TPACKET_V3 format configured
      buffers, otherwise we overwrite past the end of said buffers.
      From Eric Dumazet.

  10) Fix endianness bugs in qlcnic firmware handling, from Rajesh
      Borundia and Shahed Shaikh.

  11) CXGB4 sometimes doesn't get all of the TX completion events it
      should resulting in SKBs getting stuck in the TX queue, from
      Hariprasad Shenai.

  12) When the FEC chip's PTP clock is disabled, you can't access the
      register.  Add necessary checks to avoid the resulting hang, from
      Fugang Duan"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
  drivers: isdn: eicon: xdi_msg.h: Fix typo in #ifndef
  net: sctp: fix suboptimal edge-case on non-active active/retrans path selection
  net: sctp: spare unnecessary comparison in sctp_trans_elect_best
  net: ethernet: broadcom: bnx2x: Remove redundant #ifdef
  ibmveth: Fix endian issues with rx_no_buffer statistic
  net: xgene: fix possible NULL dereference in xgene_enet_free_desc_rings()
  openvswitch: fix panic with multiple vlan headers
  net: ipv6: fib: don't sleep inside atomic lock
  net: fec: ptp: avoid register access when ipg clock is disabled
  cxgb4: Free completed tx skbs promptly
  cxgb4: Fix race condition in cleanup
  sctp: not send SCTP_PEER_ADDR_CHANGE notifications with failed probe
  bnx2x: Revert UNDI flushing mechanism
  qlcnic: Fix endianess issue in firmware load from file operation
  qlcnic: Fix endianess issue in FW dump template header
  qlcnic: Fix flash access interface to application
  MAINTAINERS: Add section for MRF24J40 IEEE 802.15.4 radio driver
  macvlan: Allow setting multicast filter on all macvlan types
  packet: handle too big packets for PACKET_V3
  MAINTAINERS: add entry for ec_bhf driver
  ...

Test for definedness of the macro which is actually defined (the
change is hard to see: it is s/SSS/SSA/).
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In SCTP, selection of active (T.ACT) and retransmission (T.RET)
transports is being done whenever transport control operations
(UP, DOWN, PF, ...) are engaged through sctp_assoc_control_transport().

Commits 4c47af4d ("net: sctp: rework multihoming retransmission
path selection to rfc4960") and a7288c4d ("net: sctp: improve
sctp_select_active_and_retran_path selection") have both improved
it towards a more fine-grained and optimal path selection.

Currently, the selection algorithm for T.ACT and T.RET is as follows:

1) Elect the two most recently used ACTIVE transports T1, T2 for
   T.ACT, T.RET, where T.ACT<-T1 and T1 is most recently used
2) In case primary path T.PRI not in {T1, T2} but ACTIVE, set
   T.ACT<-T.PRI and T.RET<-T1
3) If only T1 is ACTIVE from the set, set T.ACT<-T1 and T.RET<-T1
4) If none is ACTIVE, set T.ACT<-best(T.PRI, T.RET, T3) where
   T3 is the most recently used (if avail) in PF, set T.RET<-T.PRI

Prior to above commits, 4) was simply a camp on T.ACT<-T.PRI and
T.RET<-T.PRI, ignoring possible paths in PF. Camping on T.PRI is
still slightly suboptimal as it can lead to the following scenario:

Setup:
        <A>                                <B>
    T1: p1p1 (10.0.10.10) <==>  .'`)  <==> p1p1 (10.0.10.12)  <= T.PRI
    T2: p1p2 (10.0.10.20) <==> (_ . ) <==> p1p2 (10.0.10.22)

    net.sctp.rto_min = 1000
    net.sctp.path_max_retrans = 2
    net.sctp.pf_retrans = 0
    net.sctp.hb_interval = 1000

T.PRI is permanently down, T2 is put briefly into PF state (e.g. due to
link flapping). Here, the first time transmission is sent over PF path
T2 as it's the only non-INACTIVE path, but the retransmitted data-chunks
are sent over the INACTIVE path T1 (T.PRI), which is not good.

After the patch, it's choosing better transports in both cases by
modifying step 4):

4) If none is ACTIVE, set T.ACT_new<-best(T.ACT_old, T3) where T3 is
   the most recently used (if avail) in PF, set T.RET<-T.ACT_new

This will still select a best possible path in PF if available (which
can also include T.PRI/T.RET), and set both T.ACT/T.RET to it.

In case sctp_assoc_control_transport() *just* put T.ACT_old into INACTIVE
as it transitioned from ACTIVE->PF->INACTIVE and stays in INACTIVE just
for a very short while before going back ACTIVE, it will guarantee that
this path will be reselected for T.ACT/T.RET since T3 (PF) is not
available.

Previously, this was not possible, as we would only select between T.PRI
and T.RET, and a possible T3 would be NULL due to the fact that we have
just transitioned T3 in sctp_assoc_control_transport() from PF->INACTIVE
and would select a suboptimal path when T.PRI/T.RET have worse properties.

In the case that T.ACT_old permanently went to INACTIVE during this
transition and there's no PF path available, plus T.PRI and T.RET are
INACTIVE as well, we would now camp on T.ACT_old, but if everything is
being INACTIVE there's really not much we can do except hoping for a
successful HB to bring one of the transports back up again and, thus
cause a new selection through sctp_assoc_control_transport().

Now both tests work fine:

Case 1:

 1. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET

 2. T1 S(ACTIVE) T.ACT, T.RET
    T2 S(PF)

 3. T1 S(ACTIVE) T.ACT, T.RET
    T2 S(INACTIVE)

 5. T1 S(PF) T.ACT, T.RET
    T2 S(INACTIVE)

[ 5.1 T1 S(INACTIVE) T.ACT, T.RET
      T2 S(INACTIVE) ]

 6. T1 S(ACTIVE) T.ACT, T.RET
    T2 S(INACTIVE)

 7. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET

Case 2:

 1. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET

 2. T1 S(PF)
    T2 S(ACTIVE) T.ACT, T.RET

 3. T1 S(INACTIVE)
    T2 S(ACTIVE) T.ACT, T.RET

 5. T1 S(INACTIVE)
    T2 S(PF) T.ACT, T.RET

[ 5.1 T1 S(INACTIVE)
      T2 S(INACTIVE) T.ACT, T.RET ]

 6. T1 S(INACTIVE)
    T2 S(ACTIVE) T.ACT, T.RET

 7. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When both transports are the same, we don't have to go down that
road only to realize that we will return the very same transport.
We are guaranteed that curr is always non-NULL. Therefore, just
short-circuit this special case.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nothing defines _ASM_GENERIC_INT_L64_H, it is a weird way to check for
64 bit longs, and u64 should be printed using %llx anyway.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hidden away in the last 8 bytes of the buffer_list page is a solitary
statistic. It needs to be byte swapped or else ethtool -S will
produce numbers that terrify the user.

Since we do this in multiple places, create a helper function with a
comment explaining what is going on.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A NULL pointer dereference is possible for the argument ring->buf_pool
which is passed to xgene_enet_free_desc_ring(), as ring could be NULL.

And now since NULL pointers are being checked for before the calls to
xgene_enet_free_desc_ring(), might as well take advantage of them and
not call the function if the argument would be NULL.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there are multiple vlan headers present in a received frame, the first
one is put into vlan_tci and protocol is set to ETH_P_8021Q. Anything in the
skb beyond the VLAN TPID may be still non-linear, including the inner TCI
and ethertype. While ovs_flow_extract takes care of IP and IPv6 headers, it
does nothing with ETH_P_8021Q. Later, if OVS_ACTION_ATTR_POP_VLAN is
executed, __pop_vlan_tci pulls the next vlan header into vlan_tci.

This leads to two things:

1. Part of the resulting ethernet header is in the non-linear part of the
   skb. When eth_type_trans is called later as the result of
   OVS_ACTION_ATTR_OUTPUT, kernel BUGs in __skb_pull. Also, __pop_vlan_tci
   is in fact accessing random data when it reads past the TPID.

2. network_header points into the ethernet header instead of behind it.
   mac_len is set to a wrong value (10), too.
Reported-by: NYulong Pei <ypei@redhat.com>
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function fib6_commit_metrics() allocates a piece of memory in mode
GFP_KERNEL while holding an atomic lock from higher up in the stack, in
the function __ip6_ins_rt(). This produces the following BUG:

> BUG: sleeping function called from invalid context at mm/slub.c:1250
> in_atomic(): 1, irqs_disabled(): 0, pid: 2909, name: dhcpcd
> 2 locks held by dhcpcd/2909:
>  #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff81978e67>] rtnl_lock+0x17/0x20
>  #1:  (&tb->tb6_lock){++--+.}, at: [<ffffffff81a6951a>] ip6_route_add+0x65a/0x800
> CPU: 1 PID: 2909 Comm: dhcpcd Not tainted 3.17.0-rc1 #1
> Hardware name: ASUS All Series/Q87T, BIOS 0216 10/16/2013
>  0000000000000008 ffff8800c8f13858 ffffffff81af135a 0000000000000000
>  ffff880212202430 ffff8800c8f13878 ffffffff810f8d3a ffff880212202c98
>  0000000000000010 ffff8800c8f138c8 ffffffff8121ad0e 0000000000000001
> Call Trace:
>  [<ffffffff81af135a>] dump_stack+0x4e/0x68
>  [<ffffffff810f8d3a>] __might_sleep+0x10a/0x120
>  [<ffffffff8121ad0e>] kmem_cache_alloc_trace+0x4e/0x190
>  [<ffffffff81a6bcd6>] ? fib6_commit_metrics+0x66/0x110
>  [<ffffffff81a6bcd6>] fib6_commit_metrics+0x66/0x110
>  [<ffffffff81a6cbf3>] fib6_add+0x883/0xa80
>  [<ffffffff81a6951a>] ? ip6_route_add+0x65a/0x800
>  [<ffffffff81a69535>] ip6_route_add+0x675/0x800
>  [<ffffffff81a68f2a>] ? ip6_route_add+0x6a/0x800
>  [<ffffffff81a6990c>] inet6_rtm_newroute+0x5c/0x80
>  [<ffffffff8197cf01>] rtnetlink_rcv_msg+0x211/0x260
>  [<ffffffff81978e67>] ? rtnl_lock+0x17/0x20
>  [<ffffffff81119708>] ? lock_release_holdtime+0x28/0x180
>  [<ffffffff81978e67>] ? rtnl_lock+0x17/0x20
>  [<ffffffff8197ccf0>] ? __rtnl_unlock+0x20/0x20
>  [<ffffffff819a989e>] netlink_rcv_skb+0x6e/0xd0
>  [<ffffffff81978ee5>] rtnetlink_rcv+0x25/0x40
>  [<ffffffff819a8e59>] netlink_unicast+0xd9/0x180
>  [<ffffffff819a9600>] netlink_sendmsg+0x700/0x770
>  [<ffffffff81103735>] ? local_clock+0x25/0x30
>  [<ffffffff8194e83c>] sock_sendmsg+0x6c/0x90
>  [<ffffffff811f98e3>] ? might_fault+0xa3/0xb0
>  [<ffffffff8195ca6d>] ? verify_iovec+0x7d/0xf0
>  [<ffffffff8194ec3e>] ___sys_sendmsg+0x37e/0x3b0
>  [<ffffffff8111ef15>] ? trace_hardirqs_on_caller+0x185/0x220
>  [<ffffffff81af979e>] ? mutex_unlock+0xe/0x10
>  [<ffffffff819a55ec>] ? netlink_insert+0xbc/0xe0
>  [<ffffffff819a65e5>] ? netlink_autobind.isra.30+0x125/0x150
>  [<ffffffff819a6520>] ? netlink_autobind.isra.30+0x60/0x150
>  [<ffffffff819a84f9>] ? netlink_bind+0x159/0x230
>  [<ffffffff811f989a>] ? might_fault+0x5a/0xb0
>  [<ffffffff8194f25e>] ? SYSC_bind+0x7e/0xd0
>  [<ffffffff8194f8cd>] __sys_sendmsg+0x4d/0x80
>  [<ffffffff8194f912>] SyS_sendmsg+0x12/0x20
>  [<ffffffff81afc692>] system_call_fastpath+0x16/0x1b

Fixing this by replacing the mode GFP_KERNEL with GFP_ATOMIC.
Signed-off-by: NBenjamin Block <bebl@mageta.org>
Acked-by: NDavid Rientjes <rientjes@google.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current kernel hang on i.MX6SX with rootfs mount from MMC.
The root cause is that ptp uses a periodic timer to access enet register
even if ipg clock is disabled.

FEC ptp driver start one period timer to read 1588 counter register in the
ptp init function that is called after FEC driver is probed.

To save power, after FEC probe finish, FEC driver disable all clocks including
ipg clock that is needed for register access.

i.MX5x, i.MX6q/dl/sl FEC register access don't cause system hang when ipg clock
is disabled, just return zero value. But for i.MX6sx SOC, it cause system hang.

To avoid the issue, we need to check ptp clock status before ptp timer count access.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull arm64 fixes from Will Deacon:
 "This small set of fixes addresses a few issues introduced during the
  merge window, including:

   - fix typo in I-cache detection that was causing us to treat all
     I-caches as aliasing
   - hook up memfd_create and getrandom syscalls for native and compat
   - revert a temporary hack for defconfig builds in -next (the audit
     tree changes didn't make it in this merge window)
   - a couple of UEFI fixes for TEXT_OFFSET fuzzing and /memreserve/
   - a simple sparsemem fix for 48-bit physical addressing
   - small defconfig updates to get autotesters working with X-gene"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  Revert "arm64: Do not invoke audit_syscall_* functions if !CONFIG_AUDIT_SYSCALL"
  arm64: mm: update max pa bits to 48
  arm64: ignore DT memreserve entries when booting in UEFI mode
  arm64: configs: Enable X-Gene SATA and ethernet in defconfig
  arm64: align randomized TEXT_OFFSET on 4 kB boundary
  asm-generic: add memfd_create system call to unistd.h
  arm64: compat: wire up memfd_create and getrandom syscalls for aarch32
  arm64: fix typo in I-cache policy detection

Pull IOMMU fixes from Joerg Roedel:
 "The fixes include:

   - fix a crash in the VT-d driver when devices with a driver attached
     are hot-unplugged

   - fix a AMD IOMMU driver crash with device assignment of 32 bit PCI
     devices to KVM guests

   - fix for a copy&paste error in generic IOMMU code.  Now the right
     function pointer is checked before calling"

* tag 'iommu-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/core: Check for the right function pointer in iommu_map()
  iommu/amd: Fix cleanup_domain for mass device removal
  iommu/vt-d: Defer domain removal if device is assigned to a driver

Description of problem:
The NIC card is not reporting back to the driver the transmitted skbs,
so they get stuck in the TX ring causing issues with reference
counters in other kernel components.

Developed a new Automatic Egress Queue Update firmware facility to slowly tick
through Egress Queues and send back any outstanding CIDX Updates which are
laying around.

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>