For Marvell SoC chips, the HDD LED does not blink when there is
disk I/O if NCQ is enabled. Add a quirk that enables blink mode for
the LED while NCQ is enabled on any port of a SoC host controller.
Normal LED function is restored when NCQ is not enabled on any port.

The code to enable the blink mode is based on earlier code
and suggestions from Frans Pop, Saeed Bishara, and possibly others.
Signed-off-by: NMark Lord <mlord@pobox.com>
Tested-by: NFrans Pop <elendil@planet.nl>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Enable use of the "all ports" IRQ coalescing optimization
for GEN_II / GEN_IIE chips that have dual host-controllers (8-ports).
Currently only the 6081 chip qualifies, but other chips may come along someday.

Rather than each half of the chip having to satisfy a local set of coalescing thresholds,
use of this feature groups all ports together under a single set of thresholds.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add IRQ coalescing to sata_mv (off by default).

This feature can reduce total interrupt overhead for RAID setups
in some situations, by deferring the interrupt signal until one or both of:

 a) a specified io_count (completed SATA commands) is achieved, or
 b) a specified time interval elapses after an IO completion.

For now, module parameters are used to set the irq_coalescing_io_count
and irq_coalescing_usecs (timeout) globally.  These may eventually
be supplemented with sysfs attributes, so that thresholds can be set
on-the-fly and on a per-chip (or even per-host_controller) basis.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Various cosmetic changes in preparation for the IRQ coalescing feature.

Note that the various MV_IRQ_COAL_* definitions are restored/renamed
in the folloup patch which adds IRQ coalescing to the driver.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

platform_get_irq() can return -ENXIO, but since 'irq' is an
unsigned int, it does not show when the IRQ resource wasn't found.
Make irq an int so that we can use a single variable to test the
platform_get_irq() return value.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NPhil Sutter <n0-1@freewrt.org>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

According to Alan:
>and yes the EFAR does UDMA66.

mwdma:
>Yep - wrong comment. The EFAR is a sort of clone of the PIIX and I
>copied the comment while EFAR don't appear to have copied the
>limitation
Signed-off-by: NErik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

As noted by Alan:
>Your suspicions are correct here btw - the device can only do MWDMA1 and
>MWDMA2 (much like some PIIX devices)
Signed-off-by: NErik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

No functional changes in this patch.
Signed-off-by: NErik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Blacklist HP Compaq 6720s so that it doesn't play a "spin down,
spin up, spin down" ping-pong with the hard disk during system
power off.
Signed-off-by: NMaciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This is initially needed to work around NCQ errata,
whereby the READ_LOG_EXT command sometimes fails
when issued in the traditional (sff) fashion.

Portions of this code will likely be reused for
implementation of the target mode feature later on.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This is necessary for use with the upcoming "mv_qc_issue_fis()" patch,
but is being added separately here for easier code review.

When using command issue via the "mv_qc_issue_fis()" mechanism,
the initial ATA_BUSY bit does not show in the ATA status (shadow) register.
This can confuse libata!  So here we add a hook to fake ATA_BUSY
for that situation, until the first time a BUSY, DRQ, or ERR bit is seen.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

so that it doesn't miss any protocols.  Handle future cases where a
qc is specially marked for polled issue or where a particular chip
version prefers interrupts over polling for PIO.

This mimics the polling decision logic from ata_sff_qc_issue().
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This also gets rid of any need for mv_mode_filter().

Using basic DMA on GEN_IIE requires setting an undocumented
bit in an undocumented register.  For safety, we clear that
bit again when switching back to EDMA mode.

To avoid a performance penalty when switching modes,
we cache the register in port_priv, as already done for other regs.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Maintain a local (mv_port_priv) cache of frequently accessed registers,
to avoid having to re-read them (very slow) on every transistion
between EDMA and non-EDMA modes.  This speeds up things like
flushing the drive write cache, and anything using basic DMA transfers.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

There's no need to turn off intx explicitly on msi enable.  This is
automatically handled by pci.  Drop it.

This might be needed on machines if the BIOS turns intx off during
boot.  However, there's no evidence of such behavior for ahci and
the only such case seems to be ICH5 PATA according to ata_piix.
Also, given the way ahci operates, it's highly unlikely BIOS ever
disables IRQ for the controller.  However, as this change has slight
possibility of introducing failure, please schedule it for #upstream.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

I'm not quite sure what freezing and thawing is used for. Tests showed
that the port is being frozen at initialisation state and thawed right
afterwards, then the functions were not called anymore. Dropping the
complete custom code for handling the frozen state seems to work at
least for a standard use case including mounting a partition, copying
some files in it (in parallel) and finally removing them and unmounting
the partition.
Signed-off-by: NPhil Sutter <n0-1@freewrt.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The biggest difference between rb532_pata_data_xfer() and
ata_sff_data_xfer32() is the call to ata_sff_pause() at the end of
rb532_pata_data_xfer() which I suppose to be unnecessary since it works
without. I've also tested using ata_sff_data_xfer() as replacement, but
since we know that the driver supports 32bit IO, using the optimised
version should be safe.
Signed-off-by: NPhil Sutter <n0-1@freewrt.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The only difference between rb532_pata_exec_command() and
ata_sff_exec_command() is added debugging output, so it can be dropped
and the standard op used instead.
Signed-off-by: NPhil Sutter <n0-1@freewrt.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Since the delay used internally is just the same as ata_sff_pause()
uses, rb532_pata_finish_io() does exactly the same as ata_sff_pause()
and thus can be replaced by the later one.
Signed-off-by: NPhil Sutter <n0-1@freewrt.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Remove redundant code left over from the earlier patch 04/07.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Try and avoid unnecessary reconfiguration of the EDMA config register
on every single non-EDMA I/O operation, by moving the call to
mv_edma_cfg() into mv_stop_edma().  It must then also be invoked
from mv_hardreset() and from mv_port_start().
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add ATAPI support to sata_mv, using sff DMA for GEN_II chipsets,
and plain old PIO for GEN_IIE.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix mv_fill_sg() to zero out the reserved word (required for ATAPI),
and to include a memory barrier.  This may also help with problems
reported by Jens on the PPC platform.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Update the logic in ata_qc_from_tag() to match that used
in similar places elsewhere in libata.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Rearrange logic in mv_qc_issue() to handle protocols
other than ATA_PROT_DMA, ATA_PROT_NCQ, and ATA_PROT_PIO.
This is in preparation for later enabling ATAPI support.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Rearrange mv_start_dma() and friends, in preparation for adding
non-EDMA DMA modes, and non-EDMA interrupts, to the driver.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Clean up the chipset GENeration FLAGS, and rename them
for consistency with other uses of GEN_XX within sata_mv.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

commit b1c4a9dd ("ucc_geth: Change
uec phy id to the same format as gianfar's") introduced a regression
in the ucc_geth driver that causes this oops when fixed-link is used:

Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc0151270
Oops: Kernel access of bad area, sig: 11 [#1]
TMCUTU
NIP: c0151270 LR: c0151270 CTR: c0017760
REGS: cf81fa60 TRAP: 0300   Not tainted  (2.6.29-rc8)
MSR: 00009032 <EE,ME,IR,DR>  CR: 24024042  XER: 20000000
DAR: 00000000, DSISR: 20000000
TASK = cf81cba0[1] 'swapper' THREAD: cf81e000
GPR00: c0151270 cf81fb10 cf81cba0 00000000 c0272e20 c025f354 00001e80
cf86b08c
GPR08: d1068200 cffffb74 06000000 d106c200 42024042 10085148 0fffd000
0ffc81a0
GPR16: 00000001 00000001 00000000 007ffeb0 00000000 0000c000 cf83f36c
cf83f000
GPR24: 00000030 cf83f360 cf81fb20 00000000 d106c200 20000000 00001e80
cf83f360
NIP [c0151270] ucc_geth_open+0x330/0x1efc
LR [c0151270] ucc_geth_open+0x330/0x1efc
Call Trace:
[cf81fb10] [c0151270] ucc_geth_open+0x330/0x1efc (unreliable)
[cf81fba0] [c0187638] dev_open+0xbc/0x12c
[cf81fbc0] [c0187e38] dev_change_flags+0x8c/0x1b0

This patch fixes the issue by removing offending (and somewhat
duplicate) code from init_phy() routine, and changes _probe()
function to use uec_mdio_bus_name().

Also, since we fully construct phy_bus_id in the _probe() routine,
we no longer need ->phy_address and ->mdio_bus fields in
ucc_geth_info structure.

I wish the patch would be a bit shorter, but it seems like the only
way to fix the issue in a sane way. Luckily, the patch has been
tested with real PHYs and fixed-link, so no further regressions
expected.
Reported-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a locking bug in the dm9000 driver.  It calls
request_irq() without setting IRQF_DISABLED ... which is
correct for handlers that support IRQ sharing, since that
behavior is not guaranteed for shared IRQs.  However, its
IRQ handler then wrongly assumes that IRQs are blocked.
So the fix just uses the right spinlock primitives in the
IRQ handler.

NOTE:  this is a classic example of the type of bug which
lockdep currently masks by forcibly setting IRQF_DISABLED
on IRQ handlers that did not request that flag.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a regression introduced when we switched to using the core
pci_set_power_state().  The chip seems to need the state to be written
over and over again until it sticks, so we do that.

Note that the code is a bit blunt, without timeout, etc...  but that's
pretty much because I put back in there the code exactly as it used to
be before the regression.  I still add a call to pci_set_power_state()
at the end so that ACPI gets called appropriately on x86.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: NRaymond Wooninck <tittiatcoke@gmail.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NIlya Yanok <yanok@emcraft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In two dca files copyright and license headers are missing.
This patch adds them there.
Signed-off-by: NMaciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sungem driver only got partially converted to net_device_ops.
Since this could cause bugs, please push this to 2.6.29
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a patch to reconfigure vlan-ids during an i/f down/up cycle
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a patch to replenish the rx-queue when it is in a starved
state (due to out-of-mem conditions)
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Every USB transfer buffer has to be allocated individually by kmalloc.

Impact: bugfix, no functional change
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Tested-by: NKolja Waschk <kawk@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smsc911x_phy_adjust_link is called periodically by the phy layer (as
it's run in polling mode), and it only updates the hardware when it sees
a change in duplex or carrier.  This patch clears the last known values
every time the interface is brought up, instead of only when the module
is loaded.

Without this patch the adjust_link function never updates the hardware
after an ifconfig down; ifconfig up.  On a full duplex link this causes
the tx error counter to increment, even though packets are correctly
transmitted, as the default MAC_CR register setting is for half duplex.

The tx errors are "no carrier" errors, which should be ignored in
full-duplex mode.  When MAC_CR is set to "full duplex" mode they are
correctly ignored by the hardware.

Note that even with this patch the tx error counter can increment if
packets are transmitted between "ifconfig up" and the first phy poll
interval.  An improved solution would use the phy interrupt with phylib,
but I haven't managed to make this work 100% robustly yet.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Address of SH_TSU_ADDR and ARSTR of SH7763 was wrong.
This revise it.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>