ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration

Hummingboard has no over current hardware, so disable the over current
detection for both ports.

Cubox-i has over current hardware, so appropriately configure this.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

arch/arm/boot/dts/imx6dl-hummingboard.dts

@@ -181,11 +181,13 @@
 };
 
 &usbh1 {
+	disable-over-current;
 	vbus-supply = <&reg_usbh1_vbus>;
 	status = "okay";
 };
 
 &usbotg {
+	disable-over-current;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hummingboard_usbotg_id>;
 	vbus-supply = <&reg_usbotg_vbus>;

arch/arm/boot/dts/imx6qdl-cubox-i.dtsi

@@ -130,16 +130,23 @@
 			fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
 		};
 
+		pinctrl_cubox_i_usbh1: cubox-i-usbh1 {
+			fsl,pins = <MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0>;
+		};
+
 		pinctrl_cubox_i_usbh1_vbus: cubox-i-usbh1-vbus {
 			fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x4001b0b0>;
 		};
 
-		pinctrl_cubox_i_usbotg_id: cubox-i-usbotg-id {
+		pinctrl_cubox_i_usbotg: cubox-i-usbotg {
 			/*
-			 * The Cubox-i pulls this low, but as it's pointless
+			 * The Cubox-i pulls ID low, but as it's pointless
 			 * leaving it as a pull-up, even if it is just 10uA.
 			 */
-			fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059
+				MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+			>;
 		};
 
 		pinctrl_cubox_i_usbotg_vbus: cubox-i-usbotg-vbus {
@@ -173,13 +180,15 @@
 };
 
 &usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cubox_i_usbh1>;
 	vbus-supply = <&reg_usbh1_vbus>;
 	status = "okay";
 };
 
 &usbotg {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_cubox_i_usbotg_id>;
+	pinctrl-0 = <&pinctrl_cubox_i_usbotg>;
 	vbus-supply = <&reg_usbotg_vbus>;
 	status = "okay";
 };