Merge branch 'davinci_mdio'

Grygorii Strashko says:

====================
net: davinci_mdio: reuse for keystone2 arch

The similar MDIO HW blocks is used by keystone 2 SoCs as
in Davinci SoCs:
- one in Gigabit Ethernet (GbE) Switch Subsystem
  See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
- one in 10 Gigabit Ethernet Subsystem
  See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf

Hence, reuse Davinci MDIO driver for Keystone 2 and
enable TI networking for Keystone 2 devices.

Also, as part of this series, enable PHY's creation from DT, because
Keystone 2 supports DT boot mode only.

Changes in v2:
- review comments applied.
  Keystone 2 compatibility string changed to "ti,keystone_mdio".
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/davinci-mdio.txt

-TI SoC Davinci MDIO Controller Device Tree Bindings
+TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings
 ---------------------------------------------------
 
 Required properties:
-- compatible		: Should be "ti,davinci_mdio"
+- compatible		: Should be "ti,davinci_mdio" or "ti,keystone_mdio"
 - reg			: physical base address and size of the davinci mdio
 			  registers map
 - bus_freq		: Mdio Bus frequency
@@ -19,7 +19,7 @@ file.
 Examples:
 
 	mdio: davinci_mdio@4A101000 {
-		compatible = "ti,cpsw";
+		compatible = "ti,davinci_mdio";
 		reg = <0x4A101000 0x1000>;
 		bus_freq = <1000000>;
 	};
@@ -27,7 +27,7 @@ Examples:
 (or)
 
 	mdio: davinci_mdio@4A101000 {
-		compatible = "ti,cpsw";
+		compatible = "ti,davinci_mdio";
 		ti,hwmods = "davinci_mdio";
 		bus_freq = <1000000>;
 	};

drivers/net/ethernet/ti/Kconfig

@@ -5,7 +5,7 @@
 config NET_VENDOR_TI
 	bool "Texas Instruments (TI) devices"
 	default y
-	depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX))
+	depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE))
 	---help---
 	  If you have a network (Ethernet) card belonging to this class, say Y
 	  and read the Ethernet-HOWTO, available from
@@ -32,7 +32,7 @@ config TI_DAVINCI_EMAC
 
 config TI_DAVINCI_MDIO
 	tristate "TI DaVinci MDIO Support"
-	depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX )
+	depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE )
 	select PHYLIB
 	---help---
 	  This driver supports TI's DaVinci MDIO module.

drivers/net/ethernet/ti/davinci_mdio.c

@@ -38,6 +38,7 @@
 #include <linux/davinci_emac.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_mdio.h>
 #include <linux/pinctrl/consumer.h>
 
 /*
@@ -95,6 +96,10 @@ struct davinci_mdio_data {
 	struct mii_bus	*bus;
 	bool		suspended;
 	unsigned long	access_time; /* jiffies */
+	/* Indicates that driver shouldn't modify phy_mask in case
+	 * if MDIO bus is registered from DT.
+	 */
+	bool		skip_scan;
 };
 
 static void __davinci_mdio_reset(struct davinci_mdio_data *data)
@@ -144,6 +149,9 @@ static int davinci_mdio_reset(struct mii_bus *bus)
 	dev_info(data->dev, "davinci mdio revision %d.%d\n",
 		 (ver >> 8) & 0xff, ver & 0xff);
 
+	if (data->skip_scan)
+		return 0;
+
 	/* get phy mask from the alive register */
 	phy_mask = __raw_readl(&data->regs->alive);
 	if (phy_mask) {
@@ -369,8 +377,17 @@ static int davinci_mdio_probe(struct platform_device *pdev)
 		goto bail_out;
 	}
 
-	/* register the mii bus */
-	ret = mdiobus_register(data->bus);
+	/* register the mii bus
+	 * Create PHYs from DT only in case if PHY child nodes are explicitly
+	 * defined to support backward compatibility with DTs which assume that
+	 * Davinci MDIO will always scan the bus for PHYs detection.
+	 */
+	if (dev->of_node && of_get_child_count(dev->of_node)) {
+		data->skip_scan = true;
+		ret = of_mdiobus_register(data->bus, dev->of_node);
+	} else {
+		ret = mdiobus_register(data->bus);
+	}
 	if (ret)
 		goto bail_out;