[PATCH] ide: CS5535 driver

Signed-off-by: NJaya Kumar <jayakumar.ide@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

drivers/ide/Kconfig

@@ -539,6 +539,15 @@ config BLK_DEV_CS5530
 
 	  It is safe to say Y to this question.
 
+config BLK_DEV_CS5535
+	tristate "AMD CS5535 chipset support"
+	depends on X86 && !X86_64
+	help
+	  Include support for UDMA on the NSC/AMD CS5535 companion chipset.
+	  This will automatically be detected and configured if found.
+
+	  It is safe to say Y to this question.
+
 config BLK_DEV_HPT34X
 	tristate "HPT34X chipset support"
 	help

drivers/ide/pci/Makefile

@@ -6,6 +6,7 @@ obj-$(CONFIG_BLK_DEV_ATIIXP)		+= atiixp.o
 obj-$(CONFIG_BLK_DEV_CMD64X)		+= cmd64x.o
 obj-$(CONFIG_BLK_DEV_CS5520)		+= cs5520.o
 obj-$(CONFIG_BLK_DEV_CS5530)		+= cs5530.o
+obj-$(CONFIG_BLK_DEV_CS5535)		+= cs5535.o
 obj-$(CONFIG_BLK_DEV_SC1200)		+= sc1200.o
 obj-$(CONFIG_BLK_DEV_CY82C693)		+= cy82c693.o
 obj-$(CONFIG_BLK_DEV_HPT34X)		+= hpt34x.o

drivers/ide/pci/cs5535.c

+/*
+ * linux/drivers/ide/pci/cs5535.c
+ *
+ * Copyright (C) 2004-2005 Advanced Micro Devices, Inc.
+ *
+ * History:
+ * 09/20/2005 - Jaya Kumar <jayakumar.ide@gmail.com>
+ * - Reworked tuneproc, set_drive, misc mods to prep for mainline
+ * - Work was sponsored by CIS (M) Sdn Bhd.
+ * Ported to Kernel 2.6.11 on June 26, 2005 by
+ *   Wolfgang Zuleger <wolfgang.zuleger@gmx.de>
+ *   Alexander Kiausch <alex.kiausch@t-online.de>
+ * Originally developed by AMD for 2.4/2.6
+ *
+ * Development of this chipset driver was funded
+ * by the nice folks at National Semiconductor/AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * Documentation:
+ *  CS5535 documentation available from AMD
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/ide.h>
+
+#include "ide-timing.h"
+
+#define MSR_ATAC_BASE		0x51300000
+#define ATAC_GLD_MSR_CAP	(MSR_ATAC_BASE+0)
+#define ATAC_GLD_MSR_CONFIG	(MSR_ATAC_BASE+0x01)
+#define ATAC_GLD_MSR_SMI	(MSR_ATAC_BASE+0x02)
+#define ATAC_GLD_MSR_ERROR	(MSR_ATAC_BASE+0x03)
+#define ATAC_GLD_MSR_PM		(MSR_ATAC_BASE+0x04)
+#define ATAC_GLD_MSR_DIAG	(MSR_ATAC_BASE+0x05)
+#define ATAC_IO_BAR		(MSR_ATAC_BASE+0x08)
+#define ATAC_RESET		(MSR_ATAC_BASE+0x10)
+#define ATAC_CH0D0_PIO		(MSR_ATAC_BASE+0x20)
+#define ATAC_CH0D0_DMA		(MSR_ATAC_BASE+0x21)
+#define ATAC_CH0D1_PIO		(MSR_ATAC_BASE+0x22)
+#define ATAC_CH0D1_DMA		(MSR_ATAC_BASE+0x23)
+#define ATAC_PCI_ABRTERR	(MSR_ATAC_BASE+0x24)
+#define ATAC_BM0_CMD_PRIM	0x00
+#define ATAC_BM0_STS_PRIM	0x02
+#define ATAC_BM0_PRD		0x04
+#define CS5535_CABLE_DETECT	0x48
+
+/* Format I PIO settings. We seperate out cmd and data for safer timings */
+
+static unsigned int cs5535_pio_cmd_timings[5] =
+{ 0xF7F4, 0x53F3, 0x13F1, 0x5131, 0x1131 };
+static unsigned int cs5535_pio_dta_timings[5] =
+{ 0xF7F4, 0xF173, 0x8141, 0x5131, 0x1131 };
+
+static unsigned int cs5535_mwdma_timings[3] =
+{ 0x7F0FFFF3, 0x7F035352, 0x7f024241 };
+
+static unsigned int cs5535_udma_timings[5] =
+{ 0x7F7436A1, 0x7F733481, 0x7F723261, 0x7F713161, 0x7F703061 };
+
+/* Macros to check if the register is the reset value -  reset value is an
+   invalid timing and indicates the register has not been set previously */
+
+#define CS5535_BAD_PIO(timings) ( (timings&~0x80000000UL) == 0x00009172 )
+#define CS5535_BAD_DMA(timings) ( (timings & 0x000FFFFF) == 0x00077771 )
+
+/****
+ *	cs5535_set_speed         -     Configure the chipset to the new speed
+ *	@drive: Drive to set up
+ *	@speed: desired speed
+ *
+ *	cs5535_set_speed() configures the chipset to a new speed.
+ */
+static void cs5535_set_speed(ide_drive_t *drive, u8 speed)
+{
+
+	u32 reg = 0, dummy;
+	int unit = drive->select.b.unit;
+
+
+	/* Set the PIO timings */
+	if ((speed & XFER_MODE) == XFER_PIO) {
+		u8 pioa;
+		u8 piob;
+		u8 cmd;
+
+		pioa = speed - XFER_PIO_0;
+		piob = ide_get_best_pio_mode(&(drive->hwif->drives[!unit]),
+						255, 4, NULL);
+		cmd = pioa < piob ? pioa : piob;
+
+		/* Write the speed of the current drive */
+		reg = (cs5535_pio_cmd_timings[cmd] << 16) |
+			cs5535_pio_dta_timings[pioa];
+		wrmsr(unit ? ATAC_CH0D1_PIO : ATAC_CH0D0_PIO, reg, 0);
+
+		/* And if nessesary - change the speed of the other drive */
+		rdmsr(unit ?  ATAC_CH0D0_PIO : ATAC_CH0D1_PIO, reg, dummy);
+
+		if (((reg >> 16) & cs5535_pio_cmd_timings[cmd]) !=
+			cs5535_pio_cmd_timings[cmd]) {
+			reg &= 0x0000FFFF;
+			reg |= cs5535_pio_cmd_timings[cmd] << 16;
+			wrmsr(unit ? ATAC_CH0D0_PIO : ATAC_CH0D1_PIO, reg, 0);
+		}
+
+		/* Set bit 31 of the DMA register for PIO format 1 timings */
+		rdmsr(unit ?  ATAC_CH0D1_DMA : ATAC_CH0D0_DMA, reg, dummy);
+		wrmsr(unit ? ATAC_CH0D1_DMA : ATAC_CH0D0_DMA,
+					reg | 0x80000000UL, 0);
+	} else {
+		rdmsr(unit ? ATAC_CH0D1_DMA : ATAC_CH0D0_DMA, reg, dummy);
+
+		reg &= 0x80000000UL;  /* Preserve the PIO format bit */
+
+		if (speed >= XFER_UDMA_0 && speed <= XFER_UDMA_7)
+			reg |= cs5535_udma_timings[speed - XFER_UDMA_0];
+		else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
+			reg |= cs5535_mwdma_timings[speed - XFER_MW_DMA_0];
+		else
+			return;
+
+		wrmsr(unit ? ATAC_CH0D1_DMA : ATAC_CH0D0_DMA, reg, 0);
+	}
+}
+
+static u8 cs5535_ratemask(ide_drive_t *drive)
+{
+	/* eighty93 will return 1 if it's 80core and capable of
+	exceeding udma2, 0 otherwise. we need ratemask to set
+	the max speed and if we can > udma2 then we return 2
+	which selects speed_max as udma4 which is the 5535's max
+	speed, and 1 selects udma2 which is the max for 40c */
+	if (!eighty_ninty_three(drive))
+		return 1;
+
+	return 2;
+}
+
+
+/****
+ *	cs5535_set_drive         -     Configure the drive to the new speed
+ *	@drive: Drive to set up
+ *	@speed: desired speed
+ *
+ *	cs5535_set_drive() configures the drive and the chipset to a
+ *	new speed. It also can be called by upper layers.
+ */
+static int cs5535_set_drive(ide_drive_t *drive, u8 speed)
+{
+	speed = ide_rate_filter(cs5535_ratemask(drive), speed);
+	ide_config_drive_speed(drive, speed);
+	cs5535_set_speed(drive, speed);
+
+	return 0;
+}
+
+/****
+ *	cs5535_tuneproc    -       PIO setup
+ *	@drive: drive to set up
+ *	@pio: mode to use (255 for 'best possible')
+ *
+ *	A callback from the upper layers for PIO-only tuning.
+ */
+static void cs5535_tuneproc(ide_drive_t *drive, u8 xferspeed)
+{
+	u8 modes[] = {	XFER_PIO_0, XFER_PIO_1, XFER_PIO_2, XFER_PIO_3,
+			XFER_PIO_4 };
+
+	/* cs5535 max pio is pio 4, best_pio will check the blacklist.
+	i think we don't need to rate_filter the incoming xferspeed
+	since we know we're only going to choose pio */
+	xferspeed = ide_get_best_pio_mode(drive, xferspeed, 4, NULL);
+	ide_config_drive_speed(drive, modes[xferspeed]);
+	cs5535_set_speed(drive, xferspeed);
+}
+
+static int cs5535_config_drive_for_dma(ide_drive_t *drive)
+{
+	u8 speed;
+
+	speed = ide_dma_speed(drive, cs5535_ratemask(drive));
+
+	/* If no DMA speed was available then let dma_check hit pio */
+	if (!speed) {
+		return 0;
+	}
+
+	cs5535_set_drive(drive, speed);
+	return ide_dma_enable(drive);
+}
+
+static int cs5535_dma_check(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif	= drive->hwif;
+	struct hd_driveid *id	= drive->id;
+	u8 speed;
+
+	drive->init_speed = 0;
+
+	if ((id->capability & 1) && drive->autodma) {
+		if (ide_use_dma(drive)) {
+			if (cs5535_config_drive_for_dma(drive))
+				return hwif->ide_dma_on(drive);
+		}
+
+		goto fast_ata_pio;
+
+	} else if ((id->capability & 8) || (id->field_valid & 2)) {
+fast_ata_pio:
+		speed = ide_get_best_pio_mode(drive, 255, 4, NULL);
+		cs5535_set_drive(drive, speed);
+		return hwif->ide_dma_off_quietly(drive);
+	}
+	/* IORDY not supported */
+	return 0;
+}
+
+static u8 __devinit cs5535_cable_detect(struct pci_dev *dev)
+{
+	u8 bit;
+
+	/* if a 80 wire cable was detected */
+	pci_read_config_byte(dev, CS5535_CABLE_DETECT, &bit);
+	return (bit & 1);
+}
+
+/****
+ *	init_hwif_cs5535        -       Initialize one ide cannel
+ *	@hwif: Channel descriptor
+ *
+ *	This gets invoked by the IDE driver once for each channel. It
+ *	performs channel-specific pre-initialization before drive probing.
+ *
+ */
+static void __devinit init_hwif_cs5535(ide_hwif_t *hwif)
+{
+	int i;
+
+	hwif->autodma = 0;
+
+	hwif->tuneproc = &cs5535_tuneproc;
+	hwif->speedproc = &cs5535_set_drive;
+	hwif->ide_dma_check = &cs5535_dma_check;
+
+	hwif->atapi_dma = 1;
+	hwif->ultra_mask = 0x1F;
+	hwif->mwdma_mask = 0x07;
+
+
+	hwif->udma_four = cs5535_cable_detect(hwif->pci_dev);
+
+	if (!noautodma)
+		hwif->autodma = 1;
+
+	/* just setting autotune and not worrying about bios timings */
+	for (i = 0; i < 2; i++) {
+		hwif->drives[i].autotune = 1;
+		hwif->drives[i].autodma = hwif->autodma;
+	}
+}
+
+static ide_pci_device_t cs5535_chipset __devinitdata = {
+	.name		= "CS5535",
+	.init_hwif	= init_hwif_cs5535,
+	.channels	= 1,
+	.autodma	= AUTODMA,
+	.bootable	= ON_BOARD,
+};
+
+static int __devinit cs5535_init_one(struct pci_dev *dev,
+					const struct pci_device_id *id)
+{
+	return ide_setup_pci_device(dev, &cs5535_chipset);
+}
+
+static struct pci_device_id cs5535_pci_tbl[] =
+{
+	{ PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_CS5535_IDE, PCI_ANY_ID,
+		PCI_ANY_ID, 0, 0, 0},
+	{ 0, },
+};
+
+MODULE_DEVICE_TABLE(pci, cs5535_pci_tbl);
+
+static struct pci_driver driver = {
+	.name       = "CS5535_IDE",
+	.id_table   = cs5535_pci_tbl,
+	.probe      = cs5535_init_one,
+};
+
+static int __init cs5535_ide_init(void)
+{
+	return ide_pci_register_driver(&driver);
+}
+
+module_init(cs5535_ide_init);
+
+MODULE_AUTHOR("AMD");
+MODULE_DESCRIPTION("PCI driver module for AMD/NS CS5535 IDE");
+MODULE_LICENSE("GPL");

include/linux/pci_ids.h

@@ -387,6 +387,7 @@
 #define PCI_DEVICE_ID_NS_SC1100_SMI	0x0511
 #define PCI_DEVICE_ID_NS_SC1100_XBUS	0x0515
 #define PCI_DEVICE_ID_NS_87410		0xd001
+#define PCI_DEVICE_ID_NS_CS5535_IDE	0x002d
 
 #define PCI_VENDOR_ID_TSENG		0x100c
 #define PCI_DEVICE_ID_TSENG_W32P_2	0x3202