ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts

This results in quite a nice cleanup for this dts file.

Note as a side-effect this also enables the on board speaker / headphones
out. I've tested that this works as advertised.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

arch/arm/boot/dts/sun5i-a13-difrnce-dit4350.dts

@@ -42,185 +42,9 @@
 
 /dts-v1/;
 #include "sun5i-a13.dtsi"
-#include "sunxi-common-regulators.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/pwm/pwm.h>
+#include "sun5i-reference-design-tablet.dtsi"
 
 / {
 	model = "Difrnce DIT4350";
 	compatible = "difrnce,dit4350", "allwinner,sun5i-a13";
-
-	aliases {
-		serial0 = &uart1;
-	};
-
-	backlight: backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
-		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
-		default-brightness-level = <8>;
-		/* TODO: backlight uses axp gpio1 as enable pin */
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-};
-
-&cpu0 {
-	cpu-supply = <&reg_dcdc2>;
-};
-
-&ehci0 {
-	status = "okay";
-};
-
-&i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
-	status = "okay";
-
-	axp209: pmic@34 {
-		reg = <0x34>;
-		interrupts = <0>;
-	};
-};
-
-#include "axp209.dtsi"
-
-&i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_a>;
-	status = "okay";
-
-	pcf8563: rtc@51 {
-		compatible = "nxp,pcf8563";
-		reg = <0x51>;
-	};
-};
-
-&lradc {
-	vref-supply = <&reg_ldo2>;
-	status = "okay";
-
-	button@200 {
-		label = "Volume Up";
-		linux,code = <KEY_VOLUMEUP>;
-		channel = <0>;
-		voltage = <200000>;
-	};
-
-	button@400 {
-		label = "Volume Down";
-		linux,code = <KEY_VOLUMEDOWN>;
-		channel = <0>;
-		voltage = <400000>;
-	};
-};
-
-&mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_d709>;
-	vmmc-supply = <&reg_vcc3v3>;
-	bus-width = <4>;
-	cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
-	cd-inverted;
-	status = "okay";
-};
-
-&otg_sram {
-	status = "okay";
-};
-
-&pio {
-	mmc0_cd_pin_d709: mmc0_cd_pin@0 {
-		allwinner,pins = "PG0";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-	};
-
-	usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
-		allwinner,pins = "PG1";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
-	};
-
-	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		allwinner,pins = "PG2";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-	};
-};
-
-&pwm {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pwm0_pins>;
-	status = "okay";
-};
-
-&reg_dcdc2 {
-	regulator-always-on;
-	regulator-min-microvolt = <1000000>;
-	regulator-max-microvolt = <1400000>;
-	regulator-name = "vdd-cpu";
-};
-
-&reg_dcdc3 {
-	regulator-always-on;
-	regulator-min-microvolt = <1250000>;
-	regulator-max-microvolt = <1250000>;
-	regulator-name = "vdd-int-pll";
-};
-
-&reg_ldo1 {
-	regulator-name = "vdd-rtc";
-};
-
-&reg_ldo2 {
-	regulator-always-on;
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
-	regulator-name = "avcc";
-};
-
-&reg_ldo3 {
-	regulator-min-microvolt = <3300000>;
-	regulator-max-microvolt = <3300000>;
-	regulator-name = "vcc-wifi";
-};
-
-&reg_usb0_vbus {
-	gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins_b>;
-	status = "okay";
-};
-
-&usb_otg {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&usb0_vbus_pin_a {
-	allwinner,pins = "PG12";
-};
-
-&usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
-	usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
-	usb0_vbus-supply = <&reg_usb0_vbus>;
-	usb1_vbus-supply = <&reg_ldo3>;
-	status = "okay";
 };