usb: musb: set AUTOSET for full speed bulk DMA transfer in host mode

The "mult" factor is not updated properly for the can_bulk_split()
case.

The AUTOSET bit in the TXCSR is not being set if the "mult"
factor is greater than 1 for the High Bandwidth ISO case.
But the "mult" factor is also greater than 1 in case of Full speed
bulk transfers with the packet splitting in TXMAXP register
enabled with can_bulk_split().

Without the AUTOSET the DMA transfers will not progress in mode1

[ balbi@ti.com : fix braces placement ]
Signed-off-by: Nsupriya karanth <supriya.karanth@stericsson.com>
Signed-off-by: NPraveena NADAHALLY <praveen.nadahally@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

drivers/usb/musb/musb_host.c

@@ -634,7 +634,17 @@ static bool musb_tx_dma_program(struct dma_controller *dma,
 		mode = 1;
 		csr |= MUSB_TXCSR_DMAMODE | MUSB_TXCSR_DMAENAB;
 		/* autoset shouldn't be set in high bandwidth */
-		if (qh->hb_mult == 1)
+		/*
+		 * Enable Autoset according to table
+		 * below
+		 * bulk_split hb_mult	Autoset_Enable
+		 *	0	1	Yes(Normal)
+		 *	0	>1	No(High BW ISO)
+		 *	1	1	Yes(HS bulk)
+		 *	1	>1	Yes(FS bulk)
+		 */
+		if (qh->hb_mult == 1 || (qh->hb_mult > 1 &&
+					can_bulk_split(hw_ep->musb, qh->type)))
 			csr |= MUSB_TXCSR_AUTOSET;
 	} else {
 		mode = 0;
@@ -791,17 +801,19 @@ static void musb_ep_program(struct musb *musb, u8 epnum,
 		/* protocol/endpoint/interval/NAKlimit */
 		if (epnum) {
 			musb_writeb(epio, MUSB_TXTYPE, qh->type_reg);
-			if (musb->double_buffer_not_ok)
+			if (musb->double_buffer_not_ok) {
 				musb_writew(epio, MUSB_TXMAXP,
 						hw_ep->max_packet_sz_tx);
-			else if (can_bulk_split(musb, qh->type))
+			} else if (can_bulk_split(musb, qh->type)) {
+				qh->hb_mult = hw_ep->max_packet_sz_tx
+						/ packet_sz;
 				musb_writew(epio, MUSB_TXMAXP, packet_sz
-					| ((hw_ep->max_packet_sz_tx /
-						packet_sz) - 1) << 11);
-			else
+					| ((qh->hb_mult) - 1) << 11);
+			} else {
 				musb_writew(epio, MUSB_TXMAXP,
 						qh->maxpacket |
 						((qh->hb_mult - 1) << 11));
+			}
 			musb_writeb(epio, MUSB_TXINTERVAL, qh->intv_reg);
 		} else {
 			musb_writeb(epio, MUSB_NAKLIMIT0, qh->intv_reg);