提交 f231ea44 编写于 作者: S Sascha Hauer

pcm038: Setup all iomux pins at once

Also, remove usage of set_irq_type after request_irq.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
上级 60c24dc7
......@@ -39,6 +39,63 @@
#include "devices.h"
static int pcm038_pins[] = {
/* UART1 */
PE12_PF_UART1_TXD,
PE13_PF_UART1_RXD,
PE14_PF_UART1_CTS,
PE15_PF_UART1_RTS,
/* UART2 */
PE3_PF_UART2_CTS,
PE4_PF_UART2_RTS,
PE6_PF_UART2_TXD,
PE7_PF_UART2_RXD,
/* UART3 */
PE8_PF_UART3_TXD,
PE9_PF_UART3_RXD,
PE10_PF_UART3_CTS,
PE11_PF_UART3_RTS,
/* FEC */
PD0_AIN_FEC_TXD0,
PD1_AIN_FEC_TXD1,
PD2_AIN_FEC_TXD2,
PD3_AIN_FEC_TXD3,
PD4_AOUT_FEC_RX_ER,
PD5_AOUT_FEC_RXD1,
PD6_AOUT_FEC_RXD2,
PD7_AOUT_FEC_RXD3,
PD8_AF_FEC_MDIO,
PD9_AIN_FEC_MDC,
PD10_AOUT_FEC_CRS,
PD11_AOUT_FEC_TX_CLK,
PD12_AOUT_FEC_RXD0,
PD13_AOUT_FEC_RX_DV,
PD14_AOUT_FEC_RX_CLK,
PD15_AOUT_FEC_COL,
PD16_AIN_FEC_TX_ER,
PF23_AIN_FEC_TX_EN,
/* I2C2 */
PC5_PF_I2C2_SDA,
PC6_PF_I2C2_SCL,
/* SPI1 */
PD25_PF_CSPI1_RDY,
PD27_PF_CSPI1_SS1,
PD28_PF_CSPI1_SS0,
PD29_PF_CSPI1_SCLK,
PD30_PF_CSPI1_MISO,
PD31_PF_CSPI1_MOSI,
/* SSI1 */
PC20_PF_SSI1_FS,
PC21_PF_SSI1_RXD,
PC22_PF_SSI1_TXD,
PC23_PF_SSI1_CLK,
/* SSI4 */
PC16_PF_SSI4_FS,
PC17_PF_SSI4_RXD,
PC18_PF_SSI4_TXD,
PC19_PF_SSI4_CLK,
};
/*
* Phytec's PCM038 comes with 2MiB battery buffered SRAM,
* 16 bit width
......@@ -88,104 +145,16 @@ static struct platform_device pcm038_nor_mtd_device = {
.resource = &pcm038_flash_resource,
};
static int mxc_uart0_pins[] = {
PE12_PF_UART1_TXD,
PE13_PF_UART1_RXD,
PE14_PF_UART1_CTS,
PE15_PF_UART1_RTS
};
static int uart_mxc_port0_init(struct platform_device *pdev)
{
return mxc_gpio_setup_multiple_pins(mxc_uart0_pins,
ARRAY_SIZE(mxc_uart0_pins), "UART0");
}
static void uart_mxc_port0_exit(struct platform_device *pdev)
{
mxc_gpio_release_multiple_pins(mxc_uart0_pins,
ARRAY_SIZE(mxc_uart0_pins));
}
static int mxc_uart1_pins[] = {
PE3_PF_UART2_CTS,
PE4_PF_UART2_RTS,
PE6_PF_UART2_TXD,
PE7_PF_UART2_RXD
};
static int uart_mxc_port1_init(struct platform_device *pdev)
{
return mxc_gpio_setup_multiple_pins(mxc_uart1_pins,
ARRAY_SIZE(mxc_uart1_pins), "UART1");
}
static void uart_mxc_port1_exit(struct platform_device *pdev)
{
mxc_gpio_release_multiple_pins(mxc_uart1_pins,
ARRAY_SIZE(mxc_uart1_pins));
}
static int mxc_uart2_pins[] = { PE8_PF_UART3_TXD,
PE9_PF_UART3_RXD,
PE10_PF_UART3_CTS,
PE11_PF_UART3_RTS };
static int uart_mxc_port2_init(struct platform_device *pdev)
{
return mxc_gpio_setup_multiple_pins(mxc_uart2_pins,
ARRAY_SIZE(mxc_uart2_pins), "UART2");
}
static void uart_mxc_port2_exit(struct platform_device *pdev)
{
mxc_gpio_release_multiple_pins(mxc_uart2_pins,
ARRAY_SIZE(mxc_uart2_pins));
}
static struct imxuart_platform_data uart_pdata[] = {
{
.init = uart_mxc_port0_init,
.exit = uart_mxc_port0_exit,
.flags = IMXUART_HAVE_RTSCTS,
}, {
.init = uart_mxc_port1_init,
.exit = uart_mxc_port1_exit,
.flags = IMXUART_HAVE_RTSCTS,
}, {
.init = uart_mxc_port2_init,
.exit = uart_mxc_port2_exit,
.flags = IMXUART_HAVE_RTSCTS,
},
};
static int mxc_fec_pins[] = {
PD0_AIN_FEC_TXD0,
PD1_AIN_FEC_TXD1,
PD2_AIN_FEC_TXD2,
PD3_AIN_FEC_TXD3,
PD4_AOUT_FEC_RX_ER,
PD5_AOUT_FEC_RXD1,
PD6_AOUT_FEC_RXD2,
PD7_AOUT_FEC_RXD3,
PD8_AF_FEC_MDIO,
PD9_AIN_FEC_MDC,
PD10_AOUT_FEC_CRS,
PD11_AOUT_FEC_TX_CLK,
PD12_AOUT_FEC_RXD0,
PD13_AOUT_FEC_RX_DV,
PD14_AOUT_FEC_RX_CLK,
PD15_AOUT_FEC_COL,
PD16_AIN_FEC_TX_ER,
PF23_AIN_FEC_TX_EN
};
static void gpio_fec_active(void)
{
mxc_gpio_setup_multiple_pins(mxc_fec_pins,
ARRAY_SIZE(mxc_fec_pins), "FEC");
}
static struct mxc_nand_platform_data pcm038_nand_board_info = {
.width = 1,
.hw_ecc = 1,
......@@ -208,26 +177,8 @@ static void __init pcm038_init_sram(void)
}
#ifdef CONFIG_I2C_IMX
static int mxc_i2c1_pins[] = {
PC5_PF_I2C2_SDA,
PC6_PF_I2C2_SCL
};
static int pcm038_i2c_1_init(struct device *dev)
{
return mxc_gpio_setup_multiple_pins(mxc_i2c1_pins, ARRAY_SIZE(mxc_i2c1_pins),
"I2C1");
}
static void pcm038_i2c_1_exit(struct device *dev)
{
mxc_gpio_release_multiple_pins(mxc_i2c1_pins, ARRAY_SIZE(mxc_i2c1_pins));
}
static struct imxi2c_platform_data pcm038_i2c_1_data = {
.bitrate = 100000,
.init = pcm038_i2c_1_init,
.exit = pcm038_i2c_1_exit,
};
static struct at24_platform_data board_eeprom = {
......@@ -254,7 +205,9 @@ static struct i2c_board_info pcm038_i2c_devices[] = {
static void __init pcm038_init(void)
{
gpio_fec_active();
mxc_gpio_setup_multiple_pins(pcm038_pins, ARRAY_SIZE(pcm038_pins),
"PCM038");
pcm038_init_sram();
mxc_register_device(&mxc_uart_device0, &uart_pdata[0]);
......
......@@ -30,57 +30,93 @@
#include "devices.h"
static int pcm970_sdhc2_get_ro(struct device *dev)
{
return gpio_get_value(GPIO_PORTC + 28);
}
static int pcm970_sdhc2_pins[] = {
static int pcm970_pins[] = {
/* SDHC */
PB4_PF_SD2_D0,
PB5_PF_SD2_D1,
PB6_PF_SD2_D2,
PB7_PF_SD2_D3,
PB8_PF_SD2_CMD,
PB9_PF_SD2_CLK,
GPIO_PORTC | 28 | GPIO_GPIO | GPIO_IN, /* card detect */
/* display */
PA5_PF_LSCLK,
PA6_PF_LD0,
PA7_PF_LD1,
PA8_PF_LD2,
PA9_PF_LD3,
PA10_PF_LD4,
PA11_PF_LD5,
PA12_PF_LD6,
PA13_PF_LD7,
PA14_PF_LD8,
PA15_PF_LD9,
PA16_PF_LD10,
PA17_PF_LD11,
PA18_PF_LD12,
PA19_PF_LD13,
PA20_PF_LD14,
PA21_PF_LD15,
PA22_PF_LD16,
PA23_PF_LD17,
PA24_PF_REV,
PA25_PF_CLS,
PA26_PF_PS,
PA27_PF_SPL_SPR,
PA28_PF_HSYNC,
PA29_PF_VSYNC,
PA30_PF_CONTRAST,
PA31_PF_OE_ACD,
/*
* it seems the data line misses a pullup, so we must enable
* the internal pullup as a local workaround
*/
PD17_PF_I2C_DATA | GPIO_PUEN,
PD18_PF_I2C_CLK,
/* Camera */
PB10_PF_CSI_D0,
PB11_PF_CSI_D1,
PB12_PF_CSI_D2,
PB13_PF_CSI_D3,
PB14_PF_CSI_D4,
PB15_PF_CSI_MCLK,
PB16_PF_CSI_PIXCLK,
PB17_PF_CSI_D5,
PB18_PF_CSI_D6,
PB19_PF_CSI_D7,
PB20_PF_CSI_VSYNC,
PB21_PF_CSI_HSYNC,
};
static int pcm970_sdhc2_get_ro(struct device *dev)
{
return gpio_get_value(GPIO_PORTC + 28);
}
static int pcm970_sdhc2_init(struct device *dev, irq_handler_t detect_irq, void *data)
{
int ret;
ret = mxc_gpio_setup_multiple_pins(pcm970_sdhc2_pins,
ARRAY_SIZE(pcm970_sdhc2_pins), "sdhc2");
if(ret)
return ret;
ret = request_irq(IRQ_GPIOC(29), detect_irq, 0,
ret = request_irq(IRQ_GPIOC(29), detect_irq, IRQF_TRIGGER_FALLING,
"imx-mmc-detect", data);
if (ret)
goto out_release_gpio;
set_irq_type(IRQ_GPIOC(29), IRQF_TRIGGER_FALLING);
return ret;
ret = gpio_request(GPIO_PORTC + 28, "imx-mmc-ro");
if (ret)
goto out_release_gpio;
if (ret) {
free_irq(IRQ_GPIOC(29), data);
return ret;
}
mxc_gpio_mode((GPIO_PORTC | 28) | GPIO_GPIO | GPIO_IN);
gpio_direction_input(GPIO_PORTC + 28);
return 0;
out_release_gpio:
mxc_gpio_release_multiple_pins(pcm970_sdhc2_pins,
ARRAY_SIZE(pcm970_sdhc2_pins));
return ret;
}
static void pcm970_sdhc2_exit(struct device *dev, void *data)
{
free_irq(IRQ_GPIOC(29), data);
gpio_free(GPIO_PORTC + 28);
mxc_gpio_release_multiple_pins(pcm970_sdhc2_pins,
ARRAY_SIZE(pcm970_sdhc2_pins));
}
static struct imxmmc_platform_data sdhc_pdata = {
......@@ -89,27 +125,6 @@ static struct imxmmc_platform_data sdhc_pdata = {
.exit = pcm970_sdhc2_exit,
};
static int mxc_fb_pins[] = {
PA5_PF_LSCLK, PA6_PF_LD0, PA7_PF_LD1, PA8_PF_LD2,
PA9_PF_LD3, PA10_PF_LD4, PA11_PF_LD5, PA12_PF_LD6,
PA13_PF_LD7, PA14_PF_LD8, PA15_PF_LD9, PA16_PF_LD10,
PA17_PF_LD11, PA18_PF_LD12, PA19_PF_LD13, PA20_PF_LD14,
PA21_PF_LD15, PA22_PF_LD16, PA23_PF_LD17, PA24_PF_REV,
PA25_PF_CLS, PA26_PF_PS, PA27_PF_SPL_SPR, PA28_PF_HSYNC,
PA29_PF_VSYNC, PA30_PF_CONTRAST, PA31_PF_OE_ACD
};
static int pcm038_fb_init(struct platform_device *pdev)
{
return mxc_gpio_setup_multiple_pins(mxc_fb_pins,
ARRAY_SIZE(mxc_fb_pins), "FB");
}
static void pcm038_fb_exit(struct platform_device *pdev)
{
mxc_gpio_release_multiple_pins(mxc_fb_pins, ARRAY_SIZE(mxc_fb_pins));
}
/*
* Connected is a portrait Sharp-QVGA display
* of type: LQ035Q7DH06
......@@ -142,9 +157,6 @@ static struct imx_fb_platform_data pcm038_fb_data = {
.pwmr = 0x00A903FF,
.lscr1 = 0x00120300,
.dmacr = 0x00020010,
.init = pcm038_fb_init,
.exit = pcm038_fb_exit,
};
/*
......@@ -155,6 +167,9 @@ static struct imx_fb_platform_data pcm038_fb_data = {
*/
void __init pcm970_baseboard_init(void)
{
mxc_gpio_setup_multiple_pins(pcm970_pins, ARRAY_SIZE(pcm970_pins),
"PCM970");
mxc_register_device(&mxc_fb_device, &pcm038_fb_data);
mxc_register_device(&mxc_sdhc_device1, &sdhc_pdata);
}
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册