brcm80211: fmac: change function bus_start parameter

Change parameter to device pointer for bus layer interface function
brcmf_bus_start. This is part of the fullmac bus interface
refactoring.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/brcm80211/brcmfmac/dhd.h

@@ -752,7 +752,7 @@ extern void brcmf_del_if(struct brcmf_pub *drvr, int ifidx);
 extern int brcmf_sendpkt(struct brcmf_pub *drvr, int ifidx,\
 			 struct sk_buff *pkt);
 
-extern int brcmf_bus_start(struct brcmf_pub *drvr);
+extern int brcmf_bus_start(struct device *dev);
 
 extern void brcmf_c_pktfilter_offload_set(struct brcmf_pub *drvr, char *arg);
 extern void brcmf_c_pktfilter_offload_enable(struct brcmf_pub *drvr, char *arg,

drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c

@@ -800,7 +800,7 @@ static int brcmf_netdev_open(struct net_device *ndev)
 
 	if (ifp->idx == 0) {	/* do it only for primary eth0 */
 		/* try to bring up bus */
-		ret = brcmf_bus_start(drvr);
+		ret = brcmf_bus_start(drvr->dev);
 		if (ret != 0) {
 			brcmf_dbg(ERROR, "failed with code %d\n", ret);
 			return -1;
@@ -960,23 +960,25 @@ struct brcmf_pub *brcmf_attach(struct brcmf_sdio *bus, uint bus_hdrlen,
 	return NULL;
 }
 
-int brcmf_bus_start(struct brcmf_pub *drvr)
+int brcmf_bus_start(struct device *dev)
 {
 	int ret = -1;
 	/* Room for "event_msgs" + '\0' + bitvec */
 	char iovbuf[BRCMF_EVENTING_MASK_LEN + 12];
+	struct brcmf_bus *bus_if = dev_get_drvdata(dev);
+	struct brcmf_pub *drvr = bus_if->drvr;
 
 	brcmf_dbg(TRACE, "\n");
 
 	/* Bring up the bus */
-	ret = brcmf_sdbrcm_bus_init(drvr->dev);
+	ret = brcmf_sdbrcm_bus_init(dev);
 	if (ret != 0) {
 		brcmf_dbg(ERROR, "brcmf_sdbrcm_bus_init failed %d\n", ret);
 		return ret;
 	}
 
 	/* If bus is not ready, can't come up */
-	if (drvr->bus_if->state != BRCMF_BUS_DATA) {
+	if (bus_if->state != BRCMF_BUS_DATA) {
 		brcmf_dbg(ERROR, "failed bus is not ready\n");
 		return -ENODEV;
 	}

drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c

@@ -3971,7 +3971,7 @@ void *brcmf_sdbrcm_probe(u32 regsva, struct brcmf_sdio_dev *sdiodev)
 	brcmf_dbg(INFO, "completed!!\n");
 
 	/* if firmware path present try to download and bring up bus */
-	ret = brcmf_bus_start(bus->drvr);
+	ret = brcmf_bus_start(bus->sdiodev->dev);
 	if (ret != 0) {
 		if (ret == -ENOLINK) {
 			brcmf_dbg(ERROR, "dongle is not responding\n");