Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c fixes from Wolfram Sang:
 "A couple of bugfixes for I2C drivers.

  Because the changes for the piix4 driver are larger than usual, the
  patches have been in linux-next for more than a week with no reports
  coming in. The rest is usual stuff"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: omap: Fix error handling for clk_get()
  i2c: piix4: Disable completely the IMC during SMBUS_BLOCK_DATA
  i2c: piix4: Fix SMBus port selection for AMD Family 17h chips
  i2c: imx: fix misleading bus recovery debug message
  i2c: imx: use IRQF_SHARED mode to request IRQ
  i2c: ismt: Separate I2C block read from SMBus block read

drivers/i2c/busses/i2c-imx.c

@@ -1021,7 +1021,7 @@ static int i2c_imx_init_recovery_info(struct imx_i2c_struct *i2c_imx,
 	}
 
 	dev_dbg(&pdev->dev, "using scl-gpio %d and sda-gpio %d for recovery\n",
-			rinfo->sda_gpio, rinfo->scl_gpio);
+			rinfo->scl_gpio, rinfo->sda_gpio);
 
 	rinfo->prepare_recovery = i2c_imx_prepare_recovery;
 	rinfo->unprepare_recovery = i2c_imx_unprepare_recovery;
@@ -1100,7 +1100,7 @@ static int i2c_imx_probe(struct platform_device *pdev)
 	}
 
 	/* Request IRQ */
-	ret = devm_request_irq(&pdev->dev, irq, i2c_imx_isr, 0,
+	ret = devm_request_irq(&pdev->dev, irq, i2c_imx_isr, IRQF_SHARED,
 				pdev->name, i2c_imx);
 	if (ret) {
 		dev_err(&pdev->dev, "can't claim irq %d\n", irq);

drivers/i2c/busses/i2c-ismt.c

@@ -340,12 +340,15 @@ static int ismt_process_desc(const struct ismt_desc *desc,
 			data->word = dma_buffer[0] | (dma_buffer[1] << 8);
 			break;
 		case I2C_SMBUS_BLOCK_DATA:
-		case I2C_SMBUS_I2C_BLOCK_DATA:
 			if (desc->rxbytes != dma_buffer[0] + 1)
 				return -EMSGSIZE;
 
 			memcpy(data->block, dma_buffer, desc->rxbytes);
 			break;
+		case I2C_SMBUS_I2C_BLOCK_DATA:
+			memcpy(&data->block[1], dma_buffer, desc->rxbytes);
+			data->block[0] = desc->rxbytes;
+			break;
 		}
 		return 0;
 	}

drivers/i2c/busses/i2c-omap.c

@@ -360,6 +360,7 @@ static int omap_i2c_init(struct omap_i2c_dev *omap)
 	unsigned long fclk_rate = 12000000;
 	unsigned long internal_clk = 0;
 	struct clk *fclk;
+	int error;
 
 	if (omap->rev >= OMAP_I2C_REV_ON_3430_3530) {
 		/*
@@ -378,6 +379,13 @@ static int omap_i2c_init(struct omap_i2c_dev *omap)
 		 * do this bit unconditionally.
 		 */
 		fclk = clk_get(omap->dev, "fck");
+		if (IS_ERR(fclk)) {
+			error = PTR_ERR(fclk);
+			dev_err(omap->dev, "could not get fck: %i\n", error);
+
+			return error;
+		}
+
 		fclk_rate = clk_get_rate(fclk);
 		clk_put(fclk);
 
@@ -410,6 +418,12 @@ static int omap_i2c_init(struct omap_i2c_dev *omap)
 		else
 			internal_clk = 4000;
 		fclk = clk_get(omap->dev, "fck");
+		if (IS_ERR(fclk)) {
+			error = PTR_ERR(fclk);
+			dev_err(omap->dev, "could not get fck: %i\n", error);
+
+			return error;
+		}
 		fclk_rate = clk_get_rate(fclk) / 1000;
 		clk_put(fclk);
 

drivers/i2c/busses/i2c-piix4.c

@@ -85,6 +85,9 @@
 /* SB800 constants */
 #define SB800_PIIX4_SMB_IDX		0xcd6
 
+#define KERNCZ_IMC_IDX			0x3e
+#define KERNCZ_IMC_DATA			0x3f
+
 /*
  * SB800 port is selected by bits 2:1 of the smb_en register (0x2c)
  * or the smb_sel register (0x2e), depending on bit 0 of register 0x2f.
@@ -94,6 +97,12 @@
 #define SB800_PIIX4_PORT_IDX_ALT	0x2e
 #define SB800_PIIX4_PORT_IDX_SEL	0x2f
 #define SB800_PIIX4_PORT_IDX_MASK	0x06
+#define SB800_PIIX4_PORT_IDX_SHIFT	1
+
+/* On kerncz, SmBus0Sel is at bit 20:19 of PMx00 DecodeEn */
+#define SB800_PIIX4_PORT_IDX_KERNCZ		0x02
+#define SB800_PIIX4_PORT_IDX_MASK_KERNCZ	0x18
+#define SB800_PIIX4_PORT_IDX_SHIFT_KERNCZ	3
 
 /* insmod parameters */
 
@@ -149,6 +158,8 @@ static const struct dmi_system_id piix4_dmi_ibm[] = {
  */
 static DEFINE_MUTEX(piix4_mutex_sb800);
 static u8 piix4_port_sel_sb800;
+static u8 piix4_port_mask_sb800;
+static u8 piix4_port_shift_sb800;
 static const char *piix4_main_port_names_sb800[PIIX4_MAX_ADAPTERS] = {
 	" port 0", " port 2", " port 3", " port 4"
 };
@@ -159,6 +170,7 @@ struct i2c_piix4_adapdata {
 
 	/* SB800 */
 	bool sb800_main;
+	bool notify_imc;
 	u8 port;		/* Port number, shifted */
 };
 
@@ -347,7 +359,19 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 
 	/* Find which register is used for port selection */
 	if (PIIX4_dev->vendor == PCI_VENDOR_ID_AMD) {
-		piix4_port_sel_sb800 = SB800_PIIX4_PORT_IDX_ALT;
+		switch (PIIX4_dev->device) {
+		case PCI_DEVICE_ID_AMD_KERNCZ_SMBUS:
+			piix4_port_sel_sb800 = SB800_PIIX4_PORT_IDX_KERNCZ;
+			piix4_port_mask_sb800 = SB800_PIIX4_PORT_IDX_MASK_KERNCZ;
+			piix4_port_shift_sb800 = SB800_PIIX4_PORT_IDX_SHIFT_KERNCZ;
+			break;
+		case PCI_DEVICE_ID_AMD_HUDSON2_SMBUS:
+		default:
+			piix4_port_sel_sb800 = SB800_PIIX4_PORT_IDX_ALT;
+			piix4_port_mask_sb800 = SB800_PIIX4_PORT_IDX_MASK;
+			piix4_port_shift_sb800 = SB800_PIIX4_PORT_IDX_SHIFT;
+			break;
+		}
 	} else {
 		mutex_lock(&piix4_mutex_sb800);
 		outb_p(SB800_PIIX4_PORT_IDX_SEL, SB800_PIIX4_SMB_IDX);
@@ -355,6 +379,8 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 		piix4_port_sel_sb800 = (port_sel & 0x01) ?
 				       SB800_PIIX4_PORT_IDX_ALT :
 				       SB800_PIIX4_PORT_IDX;
+		piix4_port_mask_sb800 = SB800_PIIX4_PORT_IDX_MASK;
+		piix4_port_shift_sb800 = SB800_PIIX4_PORT_IDX_SHIFT;
 		mutex_unlock(&piix4_mutex_sb800);
 	}
 
@@ -572,6 +598,67 @@ static s32 piix4_access(struct i2c_adapter * adap, u16 addr,
 	return 0;
 }
 
+static uint8_t piix4_imc_read(uint8_t idx)
+{
+	outb_p(idx, KERNCZ_IMC_IDX);
+	return inb_p(KERNCZ_IMC_DATA);
+}
+
+static void piix4_imc_write(uint8_t idx, uint8_t value)
+{
+	outb_p(idx, KERNCZ_IMC_IDX);
+	outb_p(value, KERNCZ_IMC_DATA);
+}
+
+static int piix4_imc_sleep(void)
+{
+	int timeout = MAX_TIMEOUT;
+
+	if (!request_muxed_region(KERNCZ_IMC_IDX, 2, "smbus_kerncz_imc"))
+		return -EBUSY;
+
+	/* clear response register */
+	piix4_imc_write(0x82, 0x00);
+	/* request ownership flag */
+	piix4_imc_write(0x83, 0xB4);
+	/* kick off IMC Mailbox command 96 */
+	piix4_imc_write(0x80, 0x96);
+
+	while (timeout--) {
+		if (piix4_imc_read(0x82) == 0xfa) {
+			release_region(KERNCZ_IMC_IDX, 2);
+			return 0;
+		}
+		usleep_range(1000, 2000);
+	}
+
+	release_region(KERNCZ_IMC_IDX, 2);
+	return -ETIMEDOUT;
+}
+
+static void piix4_imc_wakeup(void)
+{
+	int timeout = MAX_TIMEOUT;
+
+	if (!request_muxed_region(KERNCZ_IMC_IDX, 2, "smbus_kerncz_imc"))
+		return;
+
+	/* clear response register */
+	piix4_imc_write(0x82, 0x00);
+	/* release ownership flag */
+	piix4_imc_write(0x83, 0xB5);
+	/* kick off IMC Mailbox command 96 */
+	piix4_imc_write(0x80, 0x96);
+
+	while (timeout--) {
+		if (piix4_imc_read(0x82) == 0xfa)
+			break;
+		usleep_range(1000, 2000);
+	}
+
+	release_region(KERNCZ_IMC_IDX, 2);
+}
+
 /*
  * Handles access to multiple SMBus ports on the SB800.
  * The port is selected by bits 2:1 of the smb_en register (0x2c).
@@ -612,12 +699,47 @@ static s32 piix4_access_sb800(struct i2c_adapter *adap, u16 addr,
 		return -EBUSY;
 	}
 
+	/*
+	 * Notify the IMC (Integrated Micro Controller) if required.
+	 * Among other responsibilities, the IMC is in charge of monitoring
+	 * the System fans and temperature sensors, and act accordingly.
+	 * All this is done through SMBus and can/will collide
+	 * with our transactions if they are long (BLOCK_DATA).
+	 * Therefore we need to request the ownership flag during those
+	 * transactions.
+	 */
+	if ((size == I2C_SMBUS_BLOCK_DATA) && adapdata->notify_imc) {
+		int ret;
+
+		ret = piix4_imc_sleep();
+		switch (ret) {
+		case -EBUSY:
+			dev_warn(&adap->dev,
+				 "IMC base address index region 0x%x already in use.\n",
+				 KERNCZ_IMC_IDX);
+			break;
+		case -ETIMEDOUT:
+			dev_warn(&adap->dev,
+				 "Failed to communicate with the IMC.\n");
+			break;
+		default:
+			break;
+		}
+
+		/* If IMC communication fails do not retry */
+		if (ret) {
+			dev_warn(&adap->dev,
+				 "Continuing without IMC notification.\n");
+			adapdata->notify_imc = false;
+		}
+	}
+
 	outb_p(piix4_port_sel_sb800, SB800_PIIX4_SMB_IDX);
 	smba_en_lo = inb_p(SB800_PIIX4_SMB_IDX + 1);
 
 	port = adapdata->port;
-	if ((smba_en_lo & SB800_PIIX4_PORT_IDX_MASK) != port)
-		outb_p((smba_en_lo & ~SB800_PIIX4_PORT_IDX_MASK) | port,
+	if ((smba_en_lo & piix4_port_mask_sb800) != port)
+		outb_p((smba_en_lo & ~piix4_port_mask_sb800) | port,
 		       SB800_PIIX4_SMB_IDX + 1);
 
 	retval = piix4_access(adap, addr, flags, read_write,
@@ -628,6 +750,9 @@ static s32 piix4_access_sb800(struct i2c_adapter *adap, u16 addr,
 	/* Release the semaphore */
 	outb_p(smbslvcnt | 0x20, SMBSLVCNT);
 
+	if ((size == I2C_SMBUS_BLOCK_DATA) && adapdata->notify_imc)
+		piix4_imc_wakeup();
+
 	mutex_unlock(&piix4_mutex_sb800);
 
 	return retval;
@@ -679,7 +804,7 @@ static struct i2c_adapter *piix4_main_adapters[PIIX4_MAX_ADAPTERS];
 static struct i2c_adapter *piix4_aux_adapter;
 
 static int piix4_add_adapter(struct pci_dev *dev, unsigned short smba,
-			     bool sb800_main, u8 port,
+			     bool sb800_main, u8 port, bool notify_imc,
 			     const char *name, struct i2c_adapter **padap)
 {
 	struct i2c_adapter *adap;
@@ -706,7 +831,8 @@ static int piix4_add_adapter(struct pci_dev *dev, unsigned short smba,
 
 	adapdata->smba = smba;
 	adapdata->sb800_main = sb800_main;
-	adapdata->port = port << 1;
+	adapdata->port = port << piix4_port_shift_sb800;
+	adapdata->notify_imc = notify_imc;
 
 	/* set up the sysfs linkage to our parent device */
 	adap->dev.parent = &dev->dev;
@@ -728,14 +854,15 @@ static int piix4_add_adapter(struct pci_dev *dev, unsigned short smba,
 	return 0;
 }
 
-static int piix4_add_adapters_sb800(struct pci_dev *dev, unsigned short smba)
+static int piix4_add_adapters_sb800(struct pci_dev *dev, unsigned short smba,
+				    bool notify_imc)
 {
 	struct i2c_piix4_adapdata *adapdata;
 	int port;
 	int retval;
 
 	for (port = 0; port < PIIX4_MAX_ADAPTERS; port++) {
-		retval = piix4_add_adapter(dev, smba, true, port,
+		retval = piix4_add_adapter(dev, smba, true, port, notify_imc,
 					   piix4_main_port_names_sb800[port],
 					   &piix4_main_adapters[port]);
 		if (retval < 0)
@@ -769,6 +896,7 @@ static int piix4_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	     dev->device == PCI_DEVICE_ID_ATI_SBX00_SMBUS &&
 	     dev->revision >= 0x40) ||
 	    dev->vendor == PCI_VENDOR_ID_AMD) {
+		bool notify_imc = false;
 		is_sb800 = true;
 
 		if (!request_region(SB800_PIIX4_SMB_IDX, 2, "smba_idx")) {
@@ -778,6 +906,20 @@ static int piix4_probe(struct pci_dev *dev, const struct pci_device_id *id)
 			return -EBUSY;
 		}
 
+		if (dev->vendor == PCI_VENDOR_ID_AMD &&
+		    dev->device == PCI_DEVICE_ID_AMD_KERNCZ_SMBUS) {
+			u8 imc;
+
+			/*
+			 * Detect if IMC is active or not, this method is
+			 * described on coreboot's AMD IMC notes
+			 */
+			pci_bus_read_config_byte(dev->bus, PCI_DEVFN(0x14, 3),
+						 0x40, &imc);
+			if (imc & 0x80)
+				notify_imc = true;
+		}
+
 		/* base address location etc changed in SB800 */
 		retval = piix4_setup_sb800(dev, id, 0);
 		if (retval < 0) {
@@ -789,7 +931,7 @@ static int piix4_probe(struct pci_dev *dev, const struct pci_device_id *id)
 		 * Try to register multiplexed main SMBus adapter,
 		 * give up if we can't
 		 */
-		retval = piix4_add_adapters_sb800(dev, retval);
+		retval = piix4_add_adapters_sb800(dev, retval, notify_imc);
 		if (retval < 0) {
 			release_region(SB800_PIIX4_SMB_IDX, 2);
 			return retval;
@@ -800,7 +942,7 @@ static int piix4_probe(struct pci_dev *dev, const struct pci_device_id *id)
 			return retval;
 
 		/* Try to register main SMBus adapter, give up if we can't */
-		retval = piix4_add_adapter(dev, retval, false, 0, "",
+		retval = piix4_add_adapter(dev, retval, false, 0, false, "",
 					   &piix4_main_adapters[0]);
 		if (retval < 0)
 			return retval;
@@ -827,7 +969,7 @@ static int piix4_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	if (retval > 0) {
 		/* Try to add the aux adapter if it exists,
 		 * piix4_add_adapter will clean up if this fails */
-		piix4_add_adapter(dev, retval, false, 0,
+		piix4_add_adapter(dev, retval, false, 0, false,
 				  is_sb800 ? piix4_aux_port_name_sb800 : "",
 				  &piix4_aux_adapter);
 	}