Merge branch 'next/dt' into next/multiplatform

* next/dt: (182 commits)
  ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
  ARM: tegra: Add Avionic Design Medcom-Wide support
  ARM: tegra: Add Avionic Design Plutux support
  ARM: tegra: Add Avionic Design Tamonten support
  ARM: tegra: dts: Add pwm label
  ARM: dt: tegra: whistler: configure power off
  ARM: mxs: m28evk: Disable OCOTP OUI loading
  ARM: imx6q: use pll2_pfd2_396m as the enfc_sel's parent
  ARM: dts: imx6q-sabrelite: add usbotg pinctrl support
  ARM: dts: imx23-olinuxino: Add USB host support
  ARM: dts: imx6q-sabrelite: add usbmisc device
  ARM: dts: mx23: Add USB resources
  ARM: dts: mxs: Add ethernetX to macX aliases
  ARM: msm: Remove non-DT targets from 8960
  ARM: msm: Add DT support for 8960
  ARM: msm: Move io mapping prototypes to common.h
  ARM: msm: Rename board-msm8x60 to signify its DT only status
  ARM: msm: Make 8660 a DT only target
  ARM: msm: Move 8660 to DT timer
  ARM: msm: Add DT support to msm_timer
  ...

Documentation/devicetree/bindings/arm/mrvl/tauros2.txt

+* Marvell Tauros2 Cache
+
+Required properties:
+- compatible : Should be "marvell,tauros2-cache".
+- marvell,tauros2-cache-features : Specify the features supported for the
+  tauros2 cache.
+  The features including
+    CACHE_TAUROS2_PREFETCH_ON       (1 << 0)
+    CACHE_TAUROS2_LINEFILL_BURST8   (1 << 1)
+  The definition can be found at
+  arch/arm/include/asm/hardware/cache-tauros2.h
+
+Example:
+	L2: l2-cache {
+		compatible = "marvell,tauros2-cache";
+		marvell,tauros2-cache-features = <0x3>;
+	};

Documentation/devicetree/bindings/arm/msm/timer.txt

+* MSM Timer
+
+Properties:
+
+- compatible : Should at least contain "qcom,msm-timer". More specific
+  properties such as "qcom,msm-gpt" and "qcom,msm-dgt" specify a general
+  purpose timer and a debug timer respectively.
+
+- interrupts : Interrupt indicating a match event.
+
+- reg : Specifies the base address of the timer registers. The second region
+  specifies an optional register used to configure the clock divider.
+
+- clock-frequency : The frequency of the timer in Hz.
+
+Optional:
+
+- cpu-offset : per-cpu offset used when the timer is accessed without the
+  CPU remapping facilities. The offset is cpu-offset * cpu-nr.
+
+Example:
+
+       timer@200a004 {
+               compatible = "qcom,msm-gpt", "qcom,msm-timer";
+               interrupts = <1 2 0x301>;
+               reg = <0x0200a004 0x10>;
+               clock-frequency = <32768>;
+               cpu-offset = <0x40000>;
+       };
+
+       timer@200a024 {
+               compatible = "qcom,msm-dgt", "qcom,msm-timer";
+               interrupts = <1 3 0x301>;
+               reg = <0x0200a024 0x10>,
+                     <0x0200a034 0x4>;
+               clock-frequency = <6750000>;
+               cpu-offset = <0x40000>;
+       };

Documentation/devicetree/bindings/arm/omap/omap.txt

@@ -36,6 +36,9 @@ Boards:
 - OMAP3 BeagleBoard : Low cost community board
   compatible = "ti,omap3-beagle", "ti,omap3"
 
+- OMAP3 Tobi with Overo : Commercial expansion board with daughter board
+  compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3"
+
 - OMAP4 SDP : Software Developement Board
   compatible = "ti,omap4-sdp", "ti,omap4430"
 

Documentation/devicetree/bindings/clock/imx23-clock.txt

+* Clock bindings for Freescale i.MX23
+
+Required properties:
+- compatible: Should be "fsl,imx23-clkctrl"
+- reg: Address and length of the register set
+- #clock-cells: Should be <1>
+
+The clock consumer should specify the desired clock by having the clock
+ID in its "clocks" phandle cell.  The following is a full list of i.MX23
+clocks and IDs.
+
+	Clock		ID
+	------------------
+	ref_xtal	0
+	pll		1
+	ref_cpu		2
+	ref_emi		3
+	ref_pix		4
+	ref_io		5
+	saif_sel	6
+	lcdif_sel	7
+	gpmi_sel	8
+	ssp_sel		9
+	emi_sel		10
+	cpu		11
+	etm_sel		12
+	cpu_pll		13
+	cpu_xtal	14
+	hbus		15
+	xbus		16
+	lcdif_div	17
+	ssp_div		18
+	gpmi_div	19
+	emi_pll		20
+	emi_xtal	21
+	etm_div		22
+	saif_div	23
+	clk32k_div	24
+	rtc		25
+	adc		26
+	spdif_div	27
+	clk32k		28
+	dri		29
+	pwm		30
+	filt		31
+	uart		32
+	ssp		33
+	gpmi		34
+	spdif		35
+	emi		36
+	saif		37
+	lcdif		38
+	etm		39
+	usb		40
+	usb_pwr		41
+
+Examples:
+
+clks: clkctrl@80040000 {
+	compatible = "fsl,imx23-clkctrl";
+	reg = <0x80040000 0x2000>;
+	#clock-cells = <1>;
+	clock-output-names =
+		...
+		"uart",		/* 32 */
+		...
+		"end_of_list";
+};
+
+auart0: serial@8006c000 {
+	compatible = "fsl,imx23-auart";
+	reg = <0x8006c000 0x2000>;
+	interrupts = <24 25 23>;
+	clocks = <&clks 32>;
+	status = "disabled";
+};

Documentation/devicetree/bindings/clock/imx28-clock.txt

+* Clock bindings for Freescale i.MX28
+
+Required properties:
+- compatible: Should be "fsl,imx28-clkctrl"
+- reg: Address and length of the register set
+- #clock-cells: Should be <1>
+
+The clock consumer should specify the desired clock by having the clock
+ID in its "clocks" phandle cell.  The following is a full list of i.MX28
+clocks and IDs.
+
+	Clock		ID
+	------------------
+	ref_xtal	0
+	pll0		1
+	pll1		2
+	pll2		3
+	ref_cpu		4
+	ref_emi		5
+	ref_io0		6
+	ref_io1		7
+	ref_pix		8
+	ref_hsadc	9
+	ref_gpmi	10
+	saif0_sel	11
+	saif1_sel	12
+	gpmi_sel	13
+	ssp0_sel	14
+	ssp1_sel	15
+	ssp2_sel	16
+	ssp3_sel	17
+	emi_sel		18
+	etm_sel		19
+	lcdif_sel	20
+	cpu		21
+	ptp_sel		22
+	cpu_pll		23
+	cpu_xtal	24
+	hbus		25
+	xbus		26
+	ssp0_div	27
+	ssp1_div	28
+	ssp2_div	29
+	ssp3_div	30
+	gpmi_div	31
+	emi_pll		32
+	emi_xtal	33
+	lcdif_div	34
+	etm_div		35
+	ptp		36
+	saif0_div	37
+	saif1_div	38
+	clk32k_div	39
+	rtc		40
+	lradc		41
+	spdif_div	42
+	clk32k		43
+	pwm		44
+	uart		45
+	ssp0		46
+	ssp1		47
+	ssp2		48
+	ssp3		49
+	gpmi		50
+	spdif		51
+	emi		52
+	saif0		53
+	saif1		54
+	lcdif		55
+	etm		56
+	fec		57
+	can0		58
+	can1		59
+	usb0		60
+	usb1		61
+	usb0_pwr	62
+	usb1_pwr	63
+	enet_out	64
+
+Examples:
+
+clks: clkctrl@80040000 {
+	compatible = "fsl,imx28-clkctrl";
+	reg = <0x80040000 0x2000>;
+	#clock-cells = <1>;
+	clock-output-names =
+		...
+		"uart",		/* 45 */
+		...
+		"end_of_list";
+};
+
+auart0: serial@8006a000 {
+	compatible = "fsl,imx28-auart", "fsl,imx23-auart";
+	reg = <0x8006a000 0x2000>;
+	interrupts = <112 70 71>;
+	clocks = <&clks 45>;
+	status = "disabled";
+};

Documentation/devicetree/bindings/clock/imx6q-clock.txt

+* Clock bindings for Freescale i.MX6 Quad
+
+Required properties:
+- compatible: Should be "fsl,imx6q-ccm"
+- reg: Address and length of the register set
+- interrupts: Should contain CCM interrupt
+- #clock-cells: Should be <1>
+
+The clock consumer should specify the desired clock by having the clock
+ID in its "clocks" phandle cell.  The following is a full list of i.MX6Q
+clocks and IDs.
+
+	Clock			ID
+	---------------------------
+	dummy			0
+	ckil			1
+	ckih			2
+	osc			3
+	pll2_pfd0_352m		4
+	pll2_pfd1_594m		5
+	pll2_pfd2_396m		6
+	pll3_pfd0_720m		7
+	pll3_pfd1_540m		8
+	pll3_pfd2_508m		9
+	pll3_pfd3_454m		10
+	pll2_198m		11
+	pll3_120m		12
+	pll3_80m		13
+	pll3_60m		14
+	twd			15
+	step			16
+	pll1_sw			17
+	periph_pre		18
+	periph2_pre		19
+	periph_clk2_sel		20
+	periph2_clk2_sel	21
+	axi_sel			22
+	esai_sel		23
+	asrc_sel		24
+	spdif_sel		25
+	gpu2d_axi		26
+	gpu3d_axi		27
+	gpu2d_core_sel		28
+	gpu3d_core_sel		29
+	gpu3d_shader_sel	30
+	ipu1_sel		31
+	ipu2_sel		32
+	ldb_di0_sel		33
+	ldb_di1_sel		34
+	ipu1_di0_pre_sel	35
+	ipu1_di1_pre_sel	36
+	ipu2_di0_pre_sel	37
+	ipu2_di1_pre_sel	38
+	ipu1_di0_sel		39
+	ipu1_di1_sel		40
+	ipu2_di0_sel		41
+	ipu2_di1_sel		42
+	hsi_tx_sel		43
+	pcie_axi_sel		44
+	ssi1_sel		45
+	ssi2_sel		46
+	ssi3_sel		47
+	usdhc1_sel		48
+	usdhc2_sel		49
+	usdhc3_sel		50
+	usdhc4_sel		51
+	enfc_sel		52
+	emi_sel			53
+	emi_slow_sel		54
+	vdo_axi_sel		55
+	vpu_axi_sel		56
+	cko1_sel		57
+	periph			58
+	periph2			59
+	periph_clk2		60
+	periph2_clk2		61
+	ipg			62
+	ipg_per			63
+	esai_pred		64
+	esai_podf		65
+	asrc_pred		66
+	asrc_podf		67
+	spdif_pred		68
+	spdif_podf		69
+	can_root		70
+	ecspi_root		71
+	gpu2d_core_podf		72
+	gpu3d_core_podf		73
+	gpu3d_shader		74
+	ipu1_podf		75
+	ipu2_podf		76
+	ldb_di0_podf		77
+	ldb_di1_podf		78
+	ipu1_di0_pre		79
+	ipu1_di1_pre		80
+	ipu2_di0_pre		81
+	ipu2_di1_pre		82
+	hsi_tx_podf		83
+	ssi1_pred		84
+	ssi1_podf		85
+	ssi2_pred		86
+	ssi2_podf		87
+	ssi3_pred		88
+	ssi3_podf		89
+	uart_serial_podf	90
+	usdhc1_podf		91
+	usdhc2_podf		92
+	usdhc3_podf		93
+	usdhc4_podf		94
+	enfc_pred		95
+	enfc_podf		96
+	emi_podf		97
+	emi_slow_podf		98
+	vpu_axi_podf		99
+	cko1_podf		100
+	axi			101
+	mmdc_ch0_axi_podf	102
+	mmdc_ch1_axi_podf	103
+	arm			104
+	ahb			105
+	apbh_dma		106
+	asrc			107
+	can1_ipg		108
+	can1_serial		109
+	can2_ipg		110
+	can2_serial		111
+	ecspi1			112
+	ecspi2			113
+	ecspi3			114
+	ecspi4			115
+	ecspi5			116
+	enet			117
+	esai			118
+	gpt_ipg			119
+	gpt_ipg_per		120
+	gpu2d_core		121
+	gpu3d_core		122
+	hdmi_iahb		123
+	hdmi_isfr		124
+	i2c1			125
+	i2c2			126
+	i2c3			127
+	iim			128
+	enfc			129
+	ipu1			130
+	ipu1_di0		131
+	ipu1_di1		132
+	ipu2			133
+	ipu2_di0		134
+	ldb_di0			135
+	ldb_di1			136
+	ipu2_di1		137
+	hsi_tx			138
+	mlb			139
+	mmdc_ch0_axi		140
+	mmdc_ch1_axi		141
+	ocram			142
+	openvg_axi		143
+	pcie_axi		144
+	pwm1			145
+	pwm2			146
+	pwm3			147
+	pwm4			148
+	per1_bch		149
+	gpmi_bch_apb		150
+	gpmi_bch		151
+	gpmi_io			152
+	gpmi_apb		153
+	sata			154
+	sdma			155
+	spba			156
+	ssi1			157
+	ssi2			158
+	ssi3			159
+	uart_ipg		160
+	uart_serial		161
+	usboh3			162
+	usdhc1			163
+	usdhc2			164
+	usdhc3			165
+	usdhc4			166
+	vdo_axi			167
+	vpu_axi			168
+	cko1			169
+	pll1_sys		170
+	pll2_bus		171
+	pll3_usb_otg		172
+	pll4_audio		173
+	pll5_video		174
+	pll6_mlb		175
+	pll7_usb_host		176
+	pll8_enet		177
+	ssi1_ipg		178
+	ssi2_ipg		179
+	ssi3_ipg		180
+	rom			181
+	usbphy1			182
+	usbphy2			183
+	ldb_di0_div_3_5		184
+	ldb_di1_div_3_5		185
+
+Examples:
+
+clks: ccm@020c4000 {
+	compatible = "fsl,imx6q-ccm";
+	reg = <0x020c4000 0x4000>;
+	interrupts = <0 87 0x04 0 88 0x04>;
+	#clock-cells = <1>;
+	clock-output-names = ...
+			     "uart_ipg",
+			     "uart_serial",
+			     ...;
+};
+
+uart1: serial@02020000 {
+	compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
+	reg = <0x02020000 0x4000>;
+	interrupts = <0 26 0x04>;
+	clocks = <&clks 160>, <&clks 161>;
+	clock-names = "ipg", "per";
+	status = "disabled";
+};

Documentation/devicetree/bindings/gpio/gpio-samsung.txt

@@ -39,3 +39,46 @@ Example:
 		#gpio-cells = <4>;
 		gpio-controller;
 	};
+
+
+Samsung S3C24XX GPIO Controller
+
+Required properties:
+- compatible: Compatible property value should be "samsung,s3c24xx-gpio".
+
+- reg: Physical base address of the controller and length of memory mapped
+  region.
+
+- #gpio-cells: Should be 3. The syntax of the gpio specifier used by client nodes
+  should be the following with values derived from the SoC user manual.
+     <[phandle of the gpio controller node]
+      [pin number within the gpio controller]
+      [mux function]
+      [flags and pull up/down]
+
+  Values for gpio specifier:
+  - Pin number: depending on the controller a number from 0 up to 15.
+  - Mux function: Depending on the SoC and the gpio bank the gpio can be set
+                  as input, output or a special function
+  - Flags and Pull Up/Down: the values to use differ for the individual SoCs
+                    example S3C2416/S3C2450:
+                            0 - Pull Up/Down Disabled.
+                            1 - Pull Down Enabled.
+                            2 - Pull Up Enabled.
+          Bit 16 (0x00010000) - Input is active low.
+  Consult the user manual for the correct values of Mux and Pull Up/Down.
+
+- gpio-controller: Specifies that the node is a gpio controller.
+- #address-cells: should be 1.
+- #size-cells: should be 1.
+
+Example:
+
+	gpa: gpio-controller@56000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "samsung,s3c24xx-gpio";
+		reg = <0x56000000 0x10>;
+		#gpio-cells = <3>;
+		gpio-controller;
+	};

Documentation/devicetree/bindings/gpio/gpio-twl4030.txt

@@ -11,6 +11,11 @@ Required properties:
 - interrupt-controller: Mark the device node as an interrupt controller
   The first cell is the GPIO number.
   The second cell is not used.
+- ti,use-leds : Enables LEDA and LEDB outputs if set
+- ti,debounce : if n-th bit is set, debounces GPIO-n
+- ti,mmc-cd : if n-th bit is set, GPIO-n controls VMMC(n+1)
+- ti,pullups : if n-th bit is set, set a pullup on GPIO-n
+- ti,pulldowns : if n-th bit is set, set a pulldown on GPIO-n
 
 Example:
 
@@ -20,4 +25,5 @@ twl_gpio: gpio {
     gpio-controller;
     #interrupt-cells = <2>;
     interrupt-controller;
+    ti,use-leds;
 };

Documentation/devicetree/bindings/i2c/trivial-devices.txt

@@ -56,3 +56,4 @@ stm,m41t00		Serial Access TIMEKEEPER
 stm,m41t62		Serial real-time clock (RTC) with alarm
 stm,m41t80		M41T80 - SERIAL ACCESS RTC WITH ALARMS
 ti,tsc2003		I2C Touch-Screen Controller
+ti,tmp102		Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface

Documentation/devicetree/bindings/lpddr2/lpddr2-timings.txt

+* AC timing parameters of LPDDR2(JESD209-2) memories for a given speed-bin
+
+Required properties:
+- compatible : Should be "jedec,lpddr2-timings"
+- min-freq : minimum DDR clock frequency for the speed-bin. Type is <u32>
+- max-freq : maximum DDR clock frequency for the speed-bin. Type is <u32>
+
+Optional properties:
+
+The following properties represent AC timing parameters from the memory
+data-sheet of the device for a given speed-bin. All these properties are
+of type <u32> and the default unit is ps (pico seconds). Parameters with
+a different unit have a suffix indicating the unit such as 'tRAS-max-ns'
+- tRCD
+- tWR
+- tRAS-min
+- tRRD
+- tWTR
+- tXP
+- tRTP
+- tDQSCK-max
+- tFAW
+- tZQCS
+- tZQinit
+- tRPab
+- tZQCL
+- tCKESR
+- tRAS-max-ns
+- tDQSCK-max-derated
+
+Example:
+
+timings_elpida_ECB240ABACN_400mhz: lpddr2-timings@0 {
+	compatible	= "jedec,lpddr2-timings";
+	min-freq	= <10000000>;
+	max-freq	= <400000000>;
+	tRPab		= <21000>;
+	tRCD		= <18000>;
+	tWR		= <15000>;
+	tRAS-min	= <42000>;
+	tRRD		= <10000>;
+	tWTR		= <7500>;
+	tXP		= <7500>;
+	tRTP		= <7500>;
+	tCKESR		= <15000>;
+	tDQSCK-max	= <5500>;
+	tFAW		= <50000>;
+	tZQCS		= <90000>;
+	tZQCL		= <360000>;
+	tZQinit		= <1000000>;
+	tRAS-max-ns	= <70000>;
+};

Documentation/devicetree/bindings/lpddr2/lpddr2.txt

+* LPDDR2 SDRAM memories compliant to JEDEC JESD209-2
+
+Required properties:
+- compatible : Should be one of - "jedec,lpddr2-nvm", "jedec,lpddr2-s2",
+  "jedec,lpddr2-s4"
+
+  "ti,jedec-lpddr2-s2" should be listed if the memory part is LPDDR2-S2 type
+
+  "ti,jedec-lpddr2-s4" should be listed if the memory part is LPDDR2-S4 type
+
+  "ti,jedec-lpddr2-nvm" should be listed if the memory part is LPDDR2-NVM type
+
+- density  : <u32> representing density in Mb (Mega bits)
+
+- io-width : <u32> representing bus width. Possible values are 8, 16, and 32
+
+Optional properties:
+
+The following optional properties represent the minimum value of some AC
+timing parameters of the DDR device in terms of number of clock cycles.
+These values shall be obtained from the device data-sheet.
+- tRRD-min-tck
+- tWTR-min-tck
+- tXP-min-tck
+- tRTP-min-tck
+- tCKE-min-tck
+- tRPab-min-tck
+- tRCD-min-tck
+- tWR-min-tck
+- tRASmin-min-tck
+- tCKESR-min-tck
+- tFAW-min-tck
+
+Child nodes:
+- The lpddr2 node may have one or more child nodes of type "lpddr2-timings".
+  "lpddr2-timings" provides AC timing parameters of the device for
+  a given speed-bin. The user may provide the timings for as many
+  speed-bins as is required. Please see Documentation/devicetree/
+  bindings/lpddr2/lpddr2-timings.txt for more information on "lpddr2-timings"
+
+Example:
+
+elpida_ECB240ABACN : lpddr2 {
+	compatible	= "Elpida,ECB240ABACN","jedec,lpddr2-s4";
+	density		= <2048>;
+	io-width	= <32>;
+
+	tRPab-min-tck	= <3>;
+	tRCD-min-tck	= <3>;
+	tWR-min-tck	= <3>;
+	tRASmin-min-tck	= <3>;
+	tRRD-min-tck	= <2>;
+	tWTR-min-tck	= <2>;
+	tXP-min-tck	= <2>;
+	tRTP-min-tck	= <2>;
+	tCKE-min-tck	= <3>;
+	tCKESR-min-tck	= <3>;
+	tFAW-min-tck	= <8>;
+
+	timings_elpida_ECB240ABACN_400mhz: lpddr2-timings@0 {
+		compatible	= "jedec,lpddr2-timings";
+		min-freq	= <10000000>;
+		max-freq	= <400000000>;
+		tRPab		= <21000>;
+		tRCD		= <18000>;
+		tWR		= <15000>;
+		tRAS-min	= <42000>;
+		tRRD		= <10000>;
+		tWTR		= <7500>;
+		tXP		= <7500>;
+		tRTP		= <7500>;
+		tCKESR		= <15000>;
+		tDQSCK-max	= <5500>;
+		tFAW		= <50000>;
+		tZQCS		= <90000>;
+		tZQCL		= <360000>;
+		tZQinit		= <1000000>;
+		tRAS-max-ns	= <70000>;
+	};
+
+	timings_elpida_ECB240ABACN_200mhz: lpddr2-timings@1 {
+		compatible	= "jedec,lpddr2-timings";
+		min-freq	= <10000000>;
+		max-freq	= <200000000>;
+		tRPab		= <21000>;
+		tRCD		= <18000>;
+		tWR		= <15000>;
+		tRAS-min	= <42000>;
+		tRRD		= <10000>;
+		tWTR		= <10000>;
+		tXP		= <7500>;
+		tRTP		= <7500>;
+		tCKESR		= <15000>;
+		tDQSCK-max	= <5500>;
+		tFAW		= <50000>;
+		tZQCS		= <90000>;
+		tZQCL		= <360000>;
+		tZQinit		= <1000000>;
+		tRAS-max-ns	= <70000>;
+	};
+
+}

Documentation/devicetree/bindings/memory-controllers/ti/emif.txt

+* EMIF family of TI SDRAM controllers
+
+EMIF - External Memory Interface - is an SDRAM controller used in
+TI SoCs. EMIF supports, based on the IP revision, one or more of
+DDR2/DDR3/LPDDR2 protocols. This binding describes a given instance
+of the EMIF IP and memory parts attached to it.
+
+Required properties:
+- compatible	: Should be of the form "ti,emif-<ip-rev>" where <ip-rev>
+  is the IP revision of the specific EMIF instance.
+
+- phy-type	: <u32> indicating the DDR phy type. Following are the
+  allowed values
+  <1>	: Attila PHY
+  <2>	: Intelli PHY
+
+- device-handle	: phandle to a "lpddr2" node representing the memory part
+
+- ti,hwmods	: For TI hwmods processing and omap device creation
+  the value shall be "emif<n>" where <n> is the number of the EMIF
+  instance with base 1.
+
+Optional properties:
+- cs1-used		: Have this property if CS1 of this EMIF
+  instance has a memory part attached to it. If there is a memory
+  part attached to CS1, it should be the same type as the one on CS0,
+  so there is no need to give the details of this memory part.
+
+- cal-resistor-per-cs	: Have this property if the board has one
+  calibration resistor per chip-select.
+
+- hw-caps-read-idle-ctrl: Have this property if the controller
+  supports read idle window programming
+
+- hw-caps-dll-calib-ctrl: Have this property if the controller
+  supports dll calibration control
+
+- hw-caps-ll-interface	: Have this property if the controller
+  has a low latency interface and corresponding interrupt events
+
+- hw-caps-temp-alert	: Have this property if the controller
+  has capability for generating SDRAM temperature alerts
+
+Example:
+
+emif1: emif@0x4c000000 {
+	compatible	= "ti,emif-4d";
+	ti,hwmods	= "emif2";
+	phy-type	= <1>;
+	device-handle	= <&elpida_ECB240ABACN>;
+	cs1-used;
+	hw-caps-read-idle-ctrl;
+	hw-caps-ll-interface;
+	hw-caps-temp-alert;
+};

Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt

+PXA3xx NAND DT bindings
+
+Required properties:
+
+ - compatible:		Should be "marvell,pxa3xx-nand"
+ - reg: 		The register base for the controller
+ - interrupts:		The interrupt to map
+ - #address-cells:	Set to <1> if the node includes partitions
+
+Optional properties:
+
+ - marvell,nand-enable-arbiter:	Set to enable the bus arbiter
+ - marvell,nand-keep-config:	Set to keep the NAND controller config as set
+				by the bootloader
+ - num-cs:			Number of chipselect lines to usw
+
+Example:
+
+	nand0: nand@43100000 {
+		compatible = "marvell,pxa3xx-nand";
+		reg = <0x43100000 90>;
+		interrupts = <45>;
+		#address-cells = <1>;
+
+		marvell,nand-enable-arbiter;
+		marvell,nand-keep-config;
+		num-cs = <1>;
+
+		/* partitions (optional) */
+	};
+

Documentation/devicetree/bindings/rtc/pxa-rtc.txt

+* PXA RTC
+
+PXA specific RTC driver.
+
+Required properties:
+- compatible : Should be "marvell,pxa-rtc"
+
+Examples:
+
+rtc@40900000 {
+	compatible = "marvell,pxa-rtc";
+	reg = <0x40900000 0x3c>;
+	interrupts = <30 31>;
+};

arch/arm/Kconfig

@@ -273,7 +273,7 @@ config ARCH_INTEGRATOR
 	select ARM_AMBA
 	select ARCH_HAS_CPUFREQ
 	select COMMON_CLK
-	select CLK_VERSATILE
+	select COMMON_CLK_VERSATILE
 	select HAVE_TCM
 	select ICST
 	select GENERIC_CLOCKEVENTS
@@ -288,13 +288,12 @@ config ARCH_INTEGRATOR
 config ARCH_REALVIEW
 	bool "ARM Ltd. RealView family"
 	select ARM_AMBA
-	select CLKDEV_LOOKUP
-	select HAVE_MACH_CLKDEV
+	select COMMON_CLK
+	select COMMON_CLK_VERSATILE
 	select ICST
 	select GENERIC_CLOCKEVENTS
 	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select PLAT_VERSATILE
-	select PLAT_VERSATILE_CLOCK
 	select PLAT_VERSATILE_CLCD
 	select ARM_TIMER_SP804
 	select GPIO_PL061 if GPIOLIB

arch/arm/boot/dts/am335x-bone.dts

@@ -17,4 +17,64 @@
 		device_type = "memory";
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
+
+	ocp {
+		uart1: serial@44e09000 {
+			status = "okay";
+		};
+
+		i2c1: i2c@44e0b000 {
+			status = "okay";
+			clock-frequency = <400000>;
+
+			tps: tps@24 {
+				reg = <0x24>;
+			};
+
+		};
+	};
+};
+
+/include/ "tps65217.dtsi"
+
+&tps {
+	regulators {
+		dcdc1_reg: regulator@0 {
+			regulator-always-on;
+		};
+
+		dcdc2_reg: regulator@1 {
+			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+			regulator-name = "vdd_mpu";
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <1325000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		dcdc3_reg: regulator@2 {
+			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <1150000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		ldo1_reg: regulator@3 {
+			regulator-always-on;
+		};
+
+		ldo2_reg: regulator@4 {
+			regulator-always-on;
+		};
+
+		ldo3_reg: regulator@5 {
+			regulator-always-on;
+		};
+
+		ldo4_reg: regulator@6 {
+			regulator-always-on;
+		};
+	};
 };

arch/arm/boot/dts/am335x-evm.dts

@@ -17,4 +17,104 @@
 		device_type = "memory";
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
+
+	ocp {
+		uart1: serial@44e09000 {
+			status = "okay";
+		};
+
+		i2c1: i2c@44e0b000 {
+			status = "okay";
+			clock-frequency = <400000>;
+
+			tps: tps@2d {
+				reg = <0x2d>;
+			};
+		};
+	};
+
+	vbat: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
+};
+
+/include/ "tps65910.dtsi"
+
+&tps {
+	vcc1-supply = <&vbat>;
+	vcc2-supply = <&vbat>;
+	vcc3-supply = <&vbat>;
+	vcc4-supply = <&vbat>;
+	vcc5-supply = <&vbat>;
+	vcc6-supply = <&vbat>;
+	vcc7-supply = <&vbat>;
+	vccio-supply = <&vbat>;
+
+	regulators {
+		vrtc_reg: regulator@0 {
+			regulator-always-on;
+		};
+
+		vio_reg: regulator@1 {
+			regulator-always-on;
+		};
+
+		vdd1_reg: regulator@2 {
+			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+			regulator-name = "vdd_mpu";
+			regulator-min-microvolt = <912500>;
+			regulator-max-microvolt = <1312500>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd2_reg: regulator@3 {
+			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <912500>;
+			regulator-max-microvolt = <1150000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd3_reg: regulator@4 {
+			regulator-always-on;
+		};
+
+		vdig1_reg: regulator@5 {
+			regulator-always-on;
+		};
+
+		vdig2_reg: regulator@6 {
+			regulator-always-on;
+		};
+
+		vpll_reg: regulator@7 {
+			regulator-always-on;
+		};
+
+		vdac_reg: regulator@8 {
+			regulator-always-on;
+		};
+
+		vaux1_reg: regulator@9 {
+			regulator-always-on;
+		};
+
+		vaux2_reg: regulator@10 {
+			regulator-always-on;
+		};
+
+		vaux33_reg: regulator@11 {
+			regulator-always-on;
+		};
+
+		vmmc_reg: regulator@12 {
+			regulator-always-on;
+		};
+	};
 };

arch/arm/boot/dts/am33xx.dtsi

@@ -69,95 +69,146 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <1>;
+			reg = <0x44e07000 0x1000>;
+			interrupt-parent = <&intc>;
+			interrupts = <96>;
 		};
 
-		gpio2: gpio@4804C000 {
+		gpio2: gpio@4804c000 {
 			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio2";
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <1>;
+			reg = <0x4804c000 0x1000>;
+			interrupt-parent = <&intc>;
+			interrupts = <98>;
 		};
 
-		gpio3: gpio@481AC000 {
+		gpio3: gpio@481ac000 {
 			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio3";
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <1>;
+			reg = <0x481ac000 0x1000>;
+			interrupt-parent = <&intc>;
+			interrupts = <32>;
 		};
 
-		gpio4: gpio@481AE000 {
+		gpio4: gpio@481ae000 {
 			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio4";
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <1>;
+			reg = <0x481ae000 0x1000>;
+			interrupt-parent = <&intc>;
+			interrupts = <62>;
 		};
 
-		uart1: serial@44E09000 {
+		uart1: serial@44e09000 {
 			compatible = "ti,omap3-uart";
 			ti,hwmods = "uart1";
 			clock-frequency = <48000000>;
+			reg = <0x44e09000 0x2000>;
+			interrupt-parent = <&intc>;
+			interrupts = <72>;
+			status = "disabled";
 		};
 
 		uart2: serial@48022000 {
 			compatible = "ti,omap3-uart";
 			ti,hwmods = "uart2";
 			clock-frequency = <48000000>;
+			reg = <0x48022000 0x2000>;
+			interrupt-parent = <&intc>;
+			interrupts = <73>;
+			status = "disabled";
 		};
 
 		uart3: serial@48024000 {
 			compatible = "ti,omap3-uart";
 			ti,hwmods = "uart3";
 			clock-frequency = <48000000>;
+			reg = <0x48024000 0x2000>;
+			interrupt-parent = <&intc>;
+			interrupts = <74>;
+			status = "disabled";
 		};
 
-		uart4: serial@481A6000 {
+		uart4: serial@481a6000 {
 			compatible = "ti,omap3-uart";
 			ti,hwmods = "uart4";
 			clock-frequency = <48000000>;
+			reg = <0x481a6000 0x2000>;
+			interrupt-parent = <&intc>;
+			interrupts = <44>;
+			status = "disabled";
 		};
 
-		uart5: serial@481A8000 {
+		uart5: serial@481a8000 {
 			compatible = "ti,omap3-uart";
 			ti,hwmods = "uart5";
 			clock-frequency = <48000000>;
+			reg = <0x481a8000 0x2000>;
+			interrupt-parent = <&intc>;
+			interrupts = <45>;
+			status = "disabled";
 		};
 
-		uart6: serial@481AA000 {
+		uart6: serial@481aa000 {
 			compatible = "ti,omap3-uart";
 			ti,hwmods = "uart6";
 			clock-frequency = <48000000>;
+			reg = <0x481aa000 0x2000>;
+			interrupt-parent = <&intc>;
+			interrupts = <46>;
+			status = "disabled";
 		};
 
-		i2c1: i2c@44E0B000 {
+		i2c1: i2c@44e0b000 {
 			compatible = "ti,omap4-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c1";
+			reg = <0x44e0b000 0x1000>;
+			interrupt-parent = <&intc>;
+			interrupts = <70>;
+			status = "disabled";
 		};
 
-		i2c2: i2c@4802A000 {
+		i2c2: i2c@4802a000 {
 			compatible = "ti,omap4-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c2";
+			reg = <0x4802a000 0x1000>;
+			interrupt-parent = <&intc>;
+			interrupts = <71>;
+			status = "disabled";
 		};
 
-		i2c3: i2c@4819C000 {
+		i2c3: i2c@4819c000 {
 			compatible = "ti,omap4-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c3";
+			reg = <0x4819c000 0x1000>;
+			interrupt-parent = <&intc>;
+			interrupts = <30>;
+			status = "disabled";
 		};
 
 		wdt2: wdt@44e35000 {
 			compatible = "ti,omap3-wdt";
 			ti,hwmods = "wd_timer2";
+			reg = <0x44e35000 0x1000>;
+			interrupt-parent = <&intc>;
+			interrupts = <91>;
 		};
 	};
 };

arch/arm/boot/dts/ea3250.dts

@@ -166,9 +166,116 @@
 		#size-cells = <0>;
 		autorepeat;
 		button@21 {
-			label = "GPIO Key UP";
+			label = "Interrupt Key";
 			linux,code = <103>;
 			gpios = <&gpio 4 1 0>; /* GPI_P3 1 */
 		};
+		key1 {
+			label = "KEY1";
+			linux,code = <1>;
+			gpios = <&pca9532 0 0>;
+		};
+		key2 {
+			label = "KEY2";
+			linux,code = <2>;
+			gpios = <&pca9532 1 0>;
+		};
+		key3 {
+			label = "KEY3";
+			linux,code = <3>;
+			gpios = <&pca9532 2 0>;
+		};
+		key4 {
+			label = "KEY4";
+			linux,code = <4>;
+			gpios = <&pca9532 3 0>;
+		};
+		joy0 {
+			label = "Joystick Key 0";
+			linux,code = <10>;
+			gpios = <&gpio 2 0 0>; /* P2.0 */
+		};
+		joy1 {
+			label = "Joystick Key 1";
+			linux,code = <11>;
+			gpios = <&gpio 2 1 0>; /* P2.1 */
+		};
+		joy2 {
+			label = "Joystick Key 2";
+			linux,code = <12>;
+			gpios = <&gpio 2 2 0>; /* P2.2 */
+		};
+		joy3 {
+			label = "Joystick Key 3";
+			linux,code = <13>;
+			gpios = <&gpio 2 3 0>; /* P2.3 */
+		};
+		joy4 {
+			label = "Joystick Key 4";
+			linux,code = <14>;
+			gpios = <&gpio 2 4 0>; /* P2.4 */
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* LEDs on OEM Board */
+
+		led1 {
+			gpios = <&gpio 5 14 1>; /* GPO_P3 14, GPIO 93, active low */
+			linux,default-trigger = "timer";
+			default-state = "off";
+		};
+
+		led2 {
+			gpios = <&gpio 2 10 1>; /* P2.10, active low */
+			default-state = "off";
+		};
+
+		led3 {
+			gpios = <&gpio 2 11 1>; /* P2.11, active low */
+			default-state = "off";
+		};
+
+		led4 {
+			gpios = <&gpio 2 12 1>; /* P2.12, active low */
+			default-state = "off";
+		};
+
+		/* LEDs on Base Board */
+
+		lede1 {
+			gpios = <&pca9532 8 0>;
+			default-state = "off";
+		};
+		lede2 {
+			gpios = <&pca9532 9 0>;
+			default-state = "off";
+		};
+		lede3 {
+			gpios = <&pca9532 10 0>;
+			default-state = "off";
+		};
+		lede4 {
+			gpios = <&pca9532 11 0>;
+			default-state = "off";
+		};
+		lede5 {
+			gpios = <&pca9532 12 0>;
+			default-state = "off";
+		};
+		lede6 {
+			gpios = <&pca9532 13 0>;
+			default-state = "off";
+		};
+		lede7 {
+			gpios = <&pca9532 14 0>;
+			default-state = "off";
+		};
+		lede8 {
+			gpios = <&pca9532 15 0>;
+			default-state = "off";
+		};
 	};
 };

arch/arm/boot/dts/elpida_ecb240abacn.dtsi

+/*
+ * Common devices used in different OMAP boards
+ */
+
+/ {
+	elpida_ECB240ABACN: lpddr2 {
+		compatible	= "Elpida,ECB240ABACN","jedec,lpddr2-s4";
+		density		= <2048>;
+		io-width	= <32>;
+
+		tRPab-min-tck	= <3>;
+		tRCD-min-tck	= <3>;
+		tWR-min-tck	= <3>;
+		tRASmin-min-tck	= <3>;
+		tRRD-min-tck	= <2>;
+		tWTR-min-tck	= <2>;
+		tXP-min-tck	= <2>;
+		tRTP-min-tck	= <2>;
+		tCKE-min-tck	= <3>;
+		tCKESR-min-tck	= <3>;
+		tFAW-min-tck	= <8>;
+
+		timings_elpida_ECB240ABACN_400mhz: lpddr2-timings@0 {
+			compatible	= "jedec,lpddr2-timings";
+			min-freq	= <10000000>;
+			max-freq	= <400000000>;
+			tRPab		= <21000>;
+			tRCD		= <18000>;
+			tWR		= <15000>;
+			tRAS-min	= <42000>;
+			tRRD		= <10000>;
+			tWTR		= <7500>;
+			tXP		= <7500>;
+			tRTP		= <7500>;
+			tCKESR		= <15000>;
+			tDQSCK-max	= <5500>;
+			tFAW		= <50000>;
+			tZQCS		= <90000>;
+			tZQCL		= <360000>;
+			tZQinit		= <1000000>;
+			tRAS-max-ns	= <70000>;
+			tDQSCK-max-derated = <6000>;
+		};
+
+		timings_elpida_ECB240ABACN_200mhz: lpddr2-timings@1 {
+			compatible	= "jedec,lpddr2-timings";
+			min-freq	= <10000000>;
+			max-freq	= <200000000>;
+			tRPab		= <21000>;
+			tRCD		= <18000>;
+			tWR		= <15000>;
+			tRAS-min	= <42000>;
+			tRRD		= <10000>;
+			tWTR		= <10000>;
+			tXP		= <7500>;
+			tRTP		= <7500>;
+			tCKESR		= <15000>;
+			tDQSCK-max	= <5500>;
+			tFAW		= <50000>;
+			tZQCS		= <90000>;
+			tZQCL		= <360000>;
+			tZQinit		= <1000000>;
+			tRAS-max-ns	= <70000>;
+			tDQSCK-max-derated = <6000>;
+		};
+	};
+};

arch/arm/boot/dts/imx23-evk.dts

@@ -42,12 +42,13 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&hog_pins_a>;
 
-				hog_pins_a: hog-gpios@0 {
+				hog_pins_a: hog@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x1123 /* MX23_PAD_LCD_RESET__GPIO_1_18 */
 						0x11d3 /* MX23_PAD_PWM3__GPIO_1_29 */
 						0x11e3 /* MX23_PAD_PWM4__GPIO_1_30 */
+						0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */
 					>;
 					fsl,drive-strength = <0>;
 					fsl,voltage = <1>;

arch/arm/boot/dts/imx23-olinuxino.dts

@@ -31,6 +31,22 @@
 				bus-width = <4>;
 				status = "okay";
 			};
+
+			pinctrl@80018000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&hog_pins_a>;
+
+				hog_pins_a: hog@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x2013 /* MX23_PAD_SSP1_DETECT__GPIO_2_1 */
+						0x0113 /* MX23_PAD_GPMI_ALE__GPIO_0_17 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+			};
 		};
 
 		apbx@80040000 {
@@ -39,6 +55,47 @@
 				pinctrl-0 = <&duart_pins_a>;
 				status = "okay";
 			};
+
+			auart0: serial@8006c000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&auart0_2pins_a>;
+				status = "okay";
+			};
+
+			usbphy0: usbphy@8007c000 {
+				status = "okay";
+			};
+		};
+	};
+
+	ahb@80080000 {
+		usb0: usb@80080000 {
+			vbus-supply = <&reg_usb0_vbus>;
+			status = "okay";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_usb0_vbus: usb0_vbus {
+			compatible = "regulator-fixed";
+			regulator-name = "usb0_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			startup-delay-us = <300>; /* LAN9215 requires a POR of 200us minimum */
+			gpio = <&gpio0 17 0>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		user {
+			label = "green";
+			gpios = <&gpio2 1 0>;
+			linux,default-trigger = "default-on";
 		};
 	};
 };

arch/arm/boot/dts/imx23-stmp378x_devb.dts

@@ -36,7 +36,7 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&hog_pins_a>;
 
-				hog_pins_a: hog-gpios@0 {
+				hog_pins_a: hog@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x11d3 /* MX23_PAD_PWM3__GPIO_1_29 */

arch/arm/boot/dts/imx23.dtsi

@@ -52,6 +52,7 @@
 			dma-apbh@80004000 {
 				compatible = "fsl,imx23-dma-apbh";
 				reg = <0x80004000 0x2000>;
+				clocks = <&clks 15>;
 			};
 
 			ecc@80008000 {
@@ -67,6 +68,7 @@
 				reg-names = "gpmi-nand", "bch";
 				interrupts = <13>, <56>;
 				interrupt-names = "gpmi-dma", "bch";
+				clocks = <&clks 34>;
 				fsl,gpmi-dma-channel = <4>;
 				status = "disabled";
 			};
@@ -74,6 +76,7 @@
 			ssp0: ssp@80010000 {
 				reg = <0x80010000 0x2000>;
 				interrupts = <15 14>;
+				clocks = <&clks 33>;
 				fsl,ssp-dma-channel = <1>;
 				status = "disabled";
 			};
@@ -140,6 +143,17 @@
 					fsl,pull-up = <0>;
 				};
 
+				auart0_2pins_a: auart0-2pins@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x01e2 /* MX23_PAD_I2C_SCL__AUART1_TX */
+						0x01f2 /* MX23_PAD_I2C_SDA__AUART1_RX */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
 				gpmi_pins_a: gpmi-nand@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -183,7 +197,6 @@
 						0x2040 /* MX23_PAD_SSP1_DATA2__SSP1_DATA2 */
 						0x2050 /* MX23_PAD_SSP1_DATA3__SSP1_DATA3 */
 						0x2000 /* MX23_PAD_SSP1_CMD__SSP1_CMD */
-						0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */
 						0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */
 					>;
 					fsl,drive-strength = <1>;
@@ -280,6 +293,7 @@
 			dma-apbx@80024000 {
 				compatible = "fsl,imx23-dma-apbx";
 				reg = <0x80024000 0x2000>;
+				clocks = <&clks 16>;
 			};
 
 			dcp@80028000 {
@@ -306,12 +320,14 @@
 				compatible = "fsl,imx23-lcdif";
 				reg = <0x80030000 2000>;
 				interrupts = <46 45>;
+				clocks = <&clks 38>;
 				status = "disabled";
 			};
 
 			ssp1: ssp@80034000 {
 				reg = <0x80034000 0x2000>;
 				interrupts = <2 20>;
+				clocks = <&clks 33>;
 				fsl,ssp-dma-channel = <2>;
 				status = "disabled";
 			};
@@ -329,9 +345,10 @@
 			reg = <0x80040000 0x40000>;
 			ranges;
 
-			clkctl@80040000 {
+			clks: clkctrl@80040000 {
+				compatible = "fsl,imx23-clkctrl";
 				reg = <0x80040000 0x2000>;
-				status = "disabled";
+				#clock-cells = <1>;
 			};
 
 			saif0: saif@80042000 {
@@ -383,6 +400,7 @@
 			pwm: pwm@80064000 {
 				compatible = "fsl,imx23-pwm";
 				reg = <0x80064000 0x2000>;
+				clocks = <&clks 30>;
 				#pwm-cells = <2>;
 				fsl,pwm-number = <5>;
 				status = "disabled";
@@ -397,6 +415,7 @@
 				compatible = "fsl,imx23-auart";
 				reg = <0x8006c000 0x2000>;
 				interrupts = <24 25 23>;
+				clocks = <&clks 32>;
 				status = "disabled";
 			};
 
@@ -404,6 +423,7 @@
 				compatible = "fsl,imx23-auart";
 				reg = <0x8006e000 0x2000>;
 				interrupts = <59 60 58>;
+				clocks = <&clks 32>;
 				status = "disabled";
 			};
 
@@ -411,11 +431,15 @@
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x80070000 0x2000>;
 				interrupts = <0>;
+				clocks = <&clks 32>, <&clks 16>;
+				clock-names = "uart", "apb_pclk";
 				status = "disabled";
 			};
 
-			usbphy@8007c000 {
+			usbphy0: usbphy@8007c000 {
+				compatible = "fsl,imx23-usbphy";
 				reg = <0x8007c000 0x2000>;
+				clocks = <&clks 41>;
 				status = "disabled";
 			};
 		};
@@ -428,8 +452,12 @@
 		reg = <0x80080000 0x80000>;
 		ranges;
 
-		usbctrl@80080000 {
+		usb0: usb@80080000 {
+			compatible = "fsl,imx23-usb", "fsl,imx27-usb";
 			reg = <0x80080000 0x40000>;
+			interrupts = <11>;
+			fsl,usbphy = <&usbphy0>;
+			clocks = <&clks 40>;
 			status = "disabled";
 		};
 	};

arch/arm/boot/dts/imx27-phytec-phycore.dts

@@ -23,10 +23,6 @@
 	soc {
 		aipi@10000000 { /* aipi */
 
-			wdog@10002000 {
-				status = "okay";
-			};
-
 			serial@1000a000 {
 				fsl,uart-has-rtscts;
 				status = "okay";

arch/arm/boot/dts/imx27.dtsi

@@ -62,7 +62,6 @@
 				compatible = "fsl,imx27-wdt", "fsl,imx21-wdt";
 				reg = <0x10002000 0x4000>;
 				interrupts = <27>;
-				status = "disabled";
 			};
 
 			uart1: serial@1000a000 {

arch/arm/boot/dts/imx28-apx4devkit.dts

@@ -37,7 +37,7 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&hog_pins_a>;
 
-				hog_pins_a: hog-gpios@0 {
+				hog_pins_a: hog@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x0113 /* MX28_PAD_GPMI_CE1N__GPIO_0_17 */

arch/arm/boot/dts/imx28-cfa10049.dts

+/*
+ * Copyright 2012 Free Electrons
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/*
+ * The CFA-10049 is an expansion board for the CFA-10036 module, thus we
+ * need to include the CFA-10036 DTS.
+ */
+/include/ "imx28-cfa10036.dts"
+
+/ {
+	model = "Crystalfontz CFA-10049 Board";
+	compatible = "crystalfontz,cfa10049", "crystalfontz,cfa10036", "fsl,imx28";
+
+	apb@80000000 {
+		apbh@80000000 {
+			pinctrl@80018000 {
+				spi3_pins_cfa10049: spi3-cfa10049@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x0181 /* MX28_PAD_GPMI_RDN__SSP3_SCK */
+						0x01c1 /* MX28_PAD_GPMI_RESETN__SSP3_CMD */
+						0x0111 /* MX28_PAD_GPMI_CE1N__SSP3_D3 */
+						0x01a2 /* MX28_PAD_GPMI_ALE__SSP3_D4 */
+					>;
+					fsl,drive-strength = <1>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+			};
+
+			ssp3: ssp@80016000 {
+				compatible = "fsl,imx28-spi";
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi3_pins_cfa10049>;
+				status = "okay";
+
+				gpio5: gpio5@0 {
+					compatible = "fairchild,74hc595";
+					gpio-controller;
+					#gpio-cells = <2>;
+					reg = <0>;
+					registers-number = <2>;
+					spi-max-frequency = <100000>;
+				};
+
+				gpio6: gpio6@1 {
+					compatible = "fairchild,74hc595";
+					gpio-controller;
+					#gpio-cells = <2>;
+					reg = <1>;
+					registers-number = <4>;
+					spi-max-frequency = <100000>;
+				};
+
+			};
+		};
+
+		apbx@80040000 {
+			i2c1: i2c@8005a000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2c1_pins_a>;
+				status = "okay";
+			};
+
+			usbphy1: usbphy@8007e000 {
+				status = "okay";
+			};
+		};
+	};
+
+	ahb@80080000 {
+		usb1: usb@80090000 {
+			vbus-supply = <&reg_usb1_vbus>;
+			pinctrl-0 = <&usbphy1_pins_a>;
+			pinctrl-names = "default";
+			status = "okay";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_usb1_vbus: usb1_vbus {
+			compatible = "regulator-fixed";
+			regulator-name = "usb1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio0 7 1>;
+		};
+	};
+};

arch/arm/boot/dts/imx28-evk.dts

@@ -46,11 +46,28 @@
 				wp-gpios = <&gpio0 28 0>;
 			};
 
+			ssp2: ssp@80014000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx28-spi";
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi2_pins_a>;
+				status = "okay";
+
+				flash: m25p80@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "sst,sst25vf016b";
+					spi-max-frequency = <40000000>;
+					reg = <0>;
+				};
+			};
+
 			pinctrl@80018000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&hog_pins_a>;
 
-				hog_pins_a: hog-gpios@0 {
+				hog_pins_a: hog@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x20d3 /* MX28_PAD_SSP1_CMD__GPIO_2_13 */
@@ -128,6 +145,10 @@
 				status = "okay";
 			};
 
+			lradc@80050000 {
+				status = "okay";
+			};
+
 			i2c0: i2c@80058000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&i2c0_pins_a>;
@@ -140,6 +161,12 @@
 					VDDIO-supply = <&reg_3p3v>;
 
 				};
+
+				at24@51 {
+					compatible = "at24,24c32";
+					pagesize = <32>;
+					reg = <0x51>;
+				};
 			};
 
 			pwm: pwm@80064000 {

arch/arm/boot/dts/imx28-m28evk.dts

@@ -23,6 +23,8 @@
 	apb@80000000 {
 		apbh@80000000 {
 			gpmi-nand@8000c000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
 				status = "okay";
@@ -61,19 +63,40 @@
 					     &mmc0_cd_cfg
 					     &mmc0_sck_cfg>;
 				bus-width = <8>;
-				wp-gpios = <&gpio3 10 1>;
+				wp-gpios = <&gpio3 10 0>;
+				vmmc-supply = <&reg_vddio_sd0>;
 				status = "okay";
 			};
 
+			ssp2: ssp@80014000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx28-spi";
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi2_pins_a>;
+				status = "okay";
+
+				flash: m25p80@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "m25p80";
+					spi-max-frequency = <40000000>;
+					reg = <0>;
+				};
+			};
+
 			pinctrl@80018000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&hog_pins_a>;
 
-				hog_pins_a: hog-gpios@0 {
+				hog_pins_a: hog@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
+						0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
 						0x30a3 /* MX28_PAD_AUART2_CTS__GPIO_3_10 */
 						0x30b3 /* MX28_PAD_AUART2_RTS__GPIO_3_11 */
+						0x30c3 /* MX28_PAD_AUART3_RX__GPIO_3_12 */
+						0x30d3 /* MX28_PAD_AUART3_TX__GPIO_3_13 */
 					>;
 					fsl,drive-strength = <0>;
 					fsl,voltage = <1>;
@@ -129,6 +152,7 @@
 			i2c0: i2c@80058000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&i2c0_pins_a>;
+				clock-frequency = <400000>;
 				status = "okay";
 
 				sgtl5000: codec@0a {
@@ -151,32 +175,51 @@
 				};
 			};
 
+			lradc@80050000 {
+				status = "okay";
+			};
+
 			duart: serial@80074000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&duart_pins_a>;
 				status = "okay";
 			};
 
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
+			usbphy0: usbphy@8007c000 {
 				status = "okay";
 			};
 
-			auart3: serial@80070000 {
+			usbphy1: usbphy@8007e000 {
+				status = "okay";
+			};
+
+			auart0: serial@8006a000 {
 				pinctrl-names = "default";
-				pinctrl-0 = <&auart3_pins_a>;
+				pinctrl-0 = <&auart0_2pins_a>;
 				status = "okay";
 			};
 		};
 	};
 
 	ahb@80080000 {
+		usb0: usb@80080000 {
+			vbus-supply = <&reg_usb0_vbus>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&usbphy0_pins_a>;
+			status = "okay";
+		};
+
+		usb1: usb@80090000 {
+			vbus-supply = <&reg_usb1_vbus>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&usbphy1_pins_a>;
+			status = "okay";
+		};
+
 		mac0: ethernet@800f0000 {
 			phy-mode = "rmii";
 			pinctrl-names = "default";
 			pinctrl-0 = <&mac0_pins_a>;
-			phy-reset-gpios = <&gpio3 11 0>;
 			status = "okay";
 		};
 
@@ -198,6 +241,30 @@
 			regulator-max-microvolt = <3300000>;
 			regulator-always-on;
 		};
+
+		reg_vddio_sd0: vddio-sd0 {
+			compatible = "regulator-fixed";
+			regulator-name = "vddio-sd0";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio3 28 0>;
+		};
+
+		reg_usb0_vbus: usb0_vbus {
+			compatible = "regulator-fixed";
+			regulator-name = "usb0_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio3 12 0>;
+		};
+
+		reg_usb1_vbus: usb1_vbus {
+			compatible = "regulator-fixed";
+			regulator-name = "usb1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio3 13 0>;
+		};
 	};
 
 	sound {

arch/arm/boot/dts/imx28-tx28.dts

@@ -25,7 +25,7 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&hog_pins_a>;
 
-				hog_pins_a: hog-gpios@0 {
+				hog_pins_a: hog@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x40a3 /* MX28_PAD_ENET0_RXD3__GPIO_4_10 */
@@ -34,6 +34,24 @@
 					fsl,voltage = <1>;
 					fsl,pull-up = <0>;
 				};
+
+				mac0_pins_gpio: mac0-gpio-mode@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x4003 /* MX28_PAD_ENET0_MDC__GPIO_4_0 */
+						0x4013 /* MX28_PAD_ENET0_MDIO__GPIO_4_1 */
+						0x4023 /* MX28_PAD_ENET0_RX_EN__GPIO_4_2 */
+						0x4033 /* MX28_PAD_ENET0_RXD0__GPIO_4_3 */
+						0x4043 /* MX28_PAD_ENET0_RXD1__GPIO_4_4 */
+						0x4063 /* MX28_PAD_ENET0_TX_EN__GPIO_4_6 */
+						0x4073 /* MX28_PAD_ENET0_TXD0__GPIO_4_7 */
+						0x4083 /* MX28_PAD_ENET0_TXD1__GPIO_4_8 */
+						0x4103 /* MX28_PAD_ENET_CLK__GPIO_4_16 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
 			};
 		};
 
@@ -72,8 +90,9 @@
 	ahb@80080000 {
 		mac0: ethernet@800f0000 {
 			phy-mode = "rmii";
-			pinctrl-names = "default";
+			pinctrl-names = "default", "gpio_mode";
 			pinctrl-0 = <&mac0_pins_a>;
+			pinctrl-1 = <&mac0_pins_gpio>;
 			status = "okay";
 		};
 	};

arch/arm/boot/dts/imx28.dtsi

@@ -27,6 +27,8 @@
 		serial2 = &auart2;
 		serial3 = &auart3;
 		serial4 = &auart4;
+		ethernet0 = &mac0;
+		ethernet1 = &mac1;
 	};
 
 	cpus {
@@ -65,6 +67,7 @@
 			dma-apbh@80004000 {
 				compatible = "fsl,imx28-dma-apbh";
 				reg = <0x80004000 0x2000>;
+				clocks = <&clks 25>;
 			};
 
 			perfmon@80006000 {
@@ -81,34 +84,47 @@
 				reg-names = "gpmi-nand", "bch";
 				interrupts = <88>, <41>;
 				interrupt-names = "gpmi-dma", "bch";
+				clocks = <&clks 50>;
 				fsl,gpmi-dma-channel = <4>;
 				status = "disabled";
 			};
 
 			ssp0: ssp@80010000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0x80010000 0x2000>;
 				interrupts = <96 82>;
+				clocks = <&clks 46>;
 				fsl,ssp-dma-channel = <0>;
 				status = "disabled";
 			};
 
 			ssp1: ssp@80012000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0x80012000 0x2000>;
 				interrupts = <97 83>;
+				clocks = <&clks 47>;
 				fsl,ssp-dma-channel = <1>;
 				status = "disabled";
 			};
 
 			ssp2: ssp@80014000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0x80014000 0x2000>;
 				interrupts = <98 84>;
+				clocks = <&clks 48>;
 				fsl,ssp-dma-channel = <2>;
 				status = "disabled";
 			};
 
 			ssp3: ssp@80016000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0x80016000 0x2000>;
 				interrupts = <99 85>;
+				clocks = <&clks 49>;
 				fsl,ssp-dma-channel = <3>;
 				status = "disabled";
 			};
@@ -410,6 +426,28 @@
 					fsl,pull-up = <1>;
 				};
 
+				i2c0_pins_b: i2c0@1 {
+					reg = <1>;
+					fsl,pinmux-ids = <
+						0x3001 /* MX28_PAD_AUART0_RX__I2C0_SCL */
+						0x3011 /* MX28_PAD_AUART0_TX__I2C0_SDA */
+					>;
+					fsl,drive-strength = <1>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				i2c1_pins_a: i2c1@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x3101 /* MX28_PAD_PWM0__I2C1_SCL */
+						0x3111 /* MX28_PAD_PWM1__I2C1_SDA */
+					>;
+					fsl,drive-strength = <1>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
 				saif0_pins_a: saif0@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -453,6 +491,16 @@
 					fsl,pull-up = <0>;
 				};
 
+				pwm4_pins_a: pwm4@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x31d0 /* MX28_PAD_PWM4__PWM_4 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
 				lcdif_24bit_pins_a: lcdif-24bit@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -507,6 +555,49 @@
 					fsl,voltage = <1>;
 					fsl,pull-up = <0>;
 				};
+
+				spi2_pins_a: spi2@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x2100 /* MX28_PAD_SSP2_SCK__SSP2_SCK */
+						0x2110 /* MX28_PAD_SSP2_MOSI__SSP2_CMD */
+						0x2120 /* MX28_PAD_SSP2_MISO__SSP2_D0 */
+						0x2130 /* MX28_PAD_SSP2_SS0__SSP2_D3 */
+					>;
+					fsl,drive-strength = <1>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				usbphy0_pins_a: usbphy0@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x2152 /* MX28_PAD_SSP2_SS2__USB0_OVERCURRENT */
+					>;
+					fsl,drive-strength = <2>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				usbphy0_pins_b: usbphy0@1 {
+					reg = <1>;
+					fsl,pinmux-ids = <
+						0x3061 /* MX28_PAD_AUART1_CTS__USB0_OVERCURRENT */
+					>;
+					fsl,drive-strength = <2>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				usbphy1_pins_a: usbphy1@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x2142 /* MX28_PAD_SSP2_SS1__USB1_OVERCURRENT */
+					>;
+					fsl,drive-strength = <2>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
 			};
 
 			digctl@8001c000 {
@@ -523,6 +614,7 @@
 			dma-apbx@80024000 {
 				compatible = "fsl,imx28-dma-apbx";
 				reg = <0x80024000 0x2000>;
+				clocks = <&clks 26>;
 			};
 
 			dcp@80028000 {
@@ -551,6 +643,7 @@
 				compatible = "fsl,imx28-lcdif";
 				reg = <0x80030000 0x2000>;
 				interrupts = <38 86>;
+				clocks = <&clks 55>;
 				status = "disabled";
 			};
 
@@ -558,6 +651,8 @@
 				compatible = "fsl,imx28-flexcan", "fsl,p1010-flexcan";
 				reg = <0x80032000 0x2000>;
 				interrupts = <8>;
+				clocks = <&clks 58>, <&clks 58>;
+				clock-names = "ipg", "per";
 				status = "disabled";
 			};
 
@@ -565,6 +660,8 @@
 				compatible = "fsl,imx28-flexcan", "fsl,p1010-flexcan";
 				reg = <0x80034000 0x2000>;
 				interrupts = <9>;
+				clocks = <&clks 59>, <&clks 59>;
+				clock-names = "ipg", "per";
 				status = "disabled";
 			};
 
@@ -611,15 +708,17 @@
 			reg = <0x80040000 0x40000>;
 			ranges;
 
-			clkctl@80040000 {
+			clks: clkctrl@80040000 {
+				compatible = "fsl,imx28-clkctrl";
 				reg = <0x80040000 0x2000>;
-				status = "disabled";
+				#clock-cells = <1>;
 			};
 
 			saif0: saif@80042000 {
 				compatible = "fsl,imx28-saif";
 				reg = <0x80042000 0x2000>;
 				interrupts = <59 80>;
+				clocks = <&clks 53>;
 				fsl,saif-dma-channel = <4>;
 				status = "disabled";
 			};
@@ -633,12 +732,16 @@
 				compatible = "fsl,imx28-saif";
 				reg = <0x80046000 0x2000>;
 				interrupts = <58 81>;
+				clocks = <&clks 54>;
 				fsl,saif-dma-channel = <5>;
 				status = "disabled";
 			};
 
 			lradc@80050000 {
+				compatible = "fsl,imx28-lradc";
 				reg = <0x80050000 0x2000>;
+				interrupts = <10 14 15 16 17 18 19
+						20 21 22 23 24 25>;
 				status = "disabled";
 			};
 
@@ -677,6 +780,7 @@
 			pwm: pwm@80064000 {
 				compatible = "fsl,imx28-pwm", "fsl,imx23-pwm";
 				reg = <0x80064000 0x2000>;
+				clocks = <&clks 44>;
 				#pwm-cells = <2>;
 				fsl,pwm-number = <8>;
 				status = "disabled";
@@ -691,6 +795,7 @@
 				compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 				reg = <0x8006a000 0x2000>;
 				interrupts = <112 70 71>;
+				clocks = <&clks 45>;
 				status = "disabled";
 			};
 
@@ -698,6 +803,7 @@
 				compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 				reg = <0x8006c000 0x2000>;
 				interrupts = <113 72 73>;
+				clocks = <&clks 45>;
 				status = "disabled";
 			};
 
@@ -705,6 +811,7 @@
 				compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 				reg = <0x8006e000 0x2000>;
 				interrupts = <114 74 75>;
+				clocks = <&clks 45>;
 				status = "disabled";
 			};
 
@@ -712,6 +819,7 @@
 				compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 				reg = <0x80070000 0x2000>;
 				interrupts = <115 76 77>;
+				clocks = <&clks 45>;
 				status = "disabled";
 			};
 
@@ -719,6 +827,7 @@
 				compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 				reg = <0x80072000 0x2000>;
 				interrupts = <116 78 79>;
+				clocks = <&clks 45>;
 				status = "disabled";
 			};
 
@@ -726,18 +835,22 @@
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x80074000 0x1000>;
 				interrupts = <47>;
+				clocks = <&clks 45>, <&clks 26>;
+				clock-names = "uart", "apb_pclk";
 				status = "disabled";
 			};
 
 			usbphy0: usbphy@8007c000 {
 				compatible = "fsl,imx28-usbphy", "fsl,imx23-usbphy";
 				reg = <0x8007c000 0x2000>;
+				clocks = <&clks 62>;
 				status = "disabled";
 			};
 
 			usbphy1: usbphy@8007e000 {
 				compatible = "fsl,imx28-usbphy", "fsl,imx23-usbphy";
 				reg = <0x8007e000 0x2000>;
+				clocks = <&clks 63>;
 				status = "disabled";
 			};
 		};
@@ -754,6 +867,7 @@
 			compatible = "fsl,imx28-usb", "fsl,imx27-usb";
 			reg = <0x80080000 0x10000>;
 			interrupts = <93>;
+			clocks = <&clks 60>;
 			fsl,usbphy = <&usbphy0>;
 			status = "disabled";
 		};
@@ -762,6 +876,7 @@
 			compatible = "fsl,imx28-usb", "fsl,imx27-usb";
 			reg = <0x80090000 0x10000>;
 			interrupts = <92>;
+			clocks = <&clks 61>;
 			fsl,usbphy = <&usbphy1>;
 			status = "disabled";
 		};
@@ -775,6 +890,8 @@
 			compatible = "fsl,imx28-fec";
 			reg = <0x800f0000 0x4000>;
 			interrupts = <101>;
+			clocks = <&clks 57>, <&clks 57>;
+			clock-names = "ipg", "ahb";
 			status = "disabled";
 		};
 
@@ -782,6 +899,8 @@
 			compatible = "fsl,imx28-fec";
 			reg = <0x800f4000 0x4000>;
 			interrupts = <102>;
+			clocks = <&clks 57>, <&clks 57>;
+			clock-names = "ipg", "ahb";
 			status = "disabled";
 		};
 

arch/arm/boot/dts/imx51-babbage.dts

@@ -25,23 +25,31 @@
 		aips@70000000 { /* aips-1 */
 			spba@70000000 {
 				esdhc@70004000 { /* ESDHC1 */
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_esdhc1_1>;
 					fsl,cd-controller;
 					fsl,wp-controller;
 					status = "okay";
 				};
 
 				esdhc@70008000 { /* ESDHC2 */
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_esdhc2_1>;
 					cd-gpios = <&gpio1 6 0>;
 					wp-gpios = <&gpio1 5 0>;
 					status = "okay";
 				};
 
 				uart3: serial@7000c000 {
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_uart3_1>;
 					fsl,uart-has-rtscts;
 					status = "okay";
 				};
 
 				ecspi@70010000 { /* ECSPI1 */
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_ecspi1_1>;
 					fsl,spi-num-chipselects = <2>;
 					cs-gpios = <&gpio4 24 0>, <&gpio4 25 0>;
 					status = "okay";
@@ -169,31 +177,43 @@
 				};
 			};
 
-			wdog@73f98000 { /* WDOG1 */
-				status = "okay";
-			};
-
 			iomuxc@73fa8000 {
-				compatible = "fsl,imx51-iomuxc-babbage";
-				reg = <0x73fa8000 0x4000>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_hog>;
+
+				hog {
+					pinctrl_hog: hoggrp {
+						fsl,pins = <
+							694  0x20d5	/* MX51_PAD_GPIO1_0__SD1_CD */
+							697  0x20d5	/* MX51_PAD_GPIO1_1__SD1_WP */
+							737  0x100	/* MX51_PAD_GPIO1_5__GPIO1_5 */
+							740  0x100	/* MX51_PAD_GPIO1_6__GPIO1_6 */
+							121  0x5	/* MX51_PAD_EIM_A27__GPIO2_21 */
+							402  0x85	/* MX51_PAD_CSPI1_SS0__GPIO4_24 */
+							405  0x85	/* MX51_PAD_CSPI1_SS1__GPIO4_25 */
+						>;
+					};
+				};
 			};
 
 			uart1: serial@73fbc000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_1>;
 				fsl,uart-has-rtscts;
 				status = "okay";
 			};
 
 			uart2: serial@73fc0000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart2_1>;
 				status = "okay";
 			};
 		};
 
 		aips@80000000 {	/* aips-2 */
-			sdma@83fb0000 {
-				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx51.bin";
-			};
-
 			i2c@83fc4000 { /* I2C2 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c2_1>;
 				status = "okay";
 
 				sgtl5000: codec@0a {
@@ -206,10 +226,14 @@
 			};
 
 			audmux@83fd0000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_audmux_1>;
 				status = "okay";
 			};
 
 			ethernet@83fec000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_fec_1>;
 				phy-mode = "mii";
 				status = "okay";
 			};

arch/arm/boot/dts/imx51.dtsi

@@ -130,6 +130,34 @@
 				};
 			};
 
+			usb@73f80000 {
+				compatible = "fsl,imx51-usb", "fsl,imx27-usb";
+				reg = <0x73f80000 0x0200>;
+				interrupts = <18>;
+				status = "disabled";
+			};
+
+			usb@73f80200 {
+				compatible = "fsl,imx51-usb", "fsl,imx27-usb";
+				reg = <0x73f80200 0x0200>;
+				interrupts = <14>;
+				status = "disabled";
+			};
+
+			usb@73f80400 {
+				compatible = "fsl,imx51-usb", "fsl,imx27-usb";
+				reg = <0x73f80400 0x0200>;
+				interrupts = <16>;
+				status = "disabled";
+			};
+
+			usb@73f80600 {
+				compatible = "fsl,imx51-usb", "fsl,imx27-usb";
+				reg = <0x73f80600 0x0200>;
+				interrupts = <17>;
+				status = "disabled";
+			};
+
 			gpio1: gpio@73f84000 {
 				compatible = "fsl,imx51-gpio", "fsl,imx35-gpio";
 				reg = <0x73f84000 0x4000>;
@@ -174,7 +202,6 @@
 				compatible = "fsl,imx51-wdt", "fsl,imx21-wdt";
 				reg = <0x73f98000 0x4000>;
 				interrupts = <58>;
-				status = "disabled";
 			};
 
 			wdog@73f9c000 { /* WDOG2 */
@@ -184,6 +211,122 @@
 				status = "disabled";
 			};
 
+			iomuxc@73fa8000 {
+				compatible = "fsl,imx51-iomuxc";
+				reg = <0x73fa8000 0x4000>;
+
+				audmux {
+					pinctrl_audmux_1: audmuxgrp-1 {
+						fsl,pins = <
+							384 0x80000000	/* MX51_PAD_AUD3_BB_TXD__AUD3_TXD */
+							386 0x80000000	/* MX51_PAD_AUD3_BB_RXD__AUD3_RXD */
+							389 0x80000000	/* MX51_PAD_AUD3_BB_CK__AUD3_TXC */
+							391 0x80000000	/* MX51_PAD_AUD3_BB_FS__AUD3_TXFS */
+						>;
+					};
+				};
+
+				fec {
+					pinctrl_fec_1: fecgrp-1 {
+						fsl,pins = <
+							128 0x80000000	/* MX51_PAD_EIM_EB2__FEC_MDIO */
+							134 0x80000000	/* MX51_PAD_EIM_EB3__FEC_RDATA1 */
+							146 0x80000000	/* MX51_PAD_EIM_CS2__FEC_RDATA2 */
+							152 0x80000000	/* MX51_PAD_EIM_CS3__FEC_RDATA3 */
+							158 0x80000000	/* MX51_PAD_EIM_CS4__FEC_RX_ER */
+							165 0x80000000	/* MX51_PAD_EIM_CS5__FEC_CRS */
+							206 0x80000000	/* MX51_PAD_NANDF_RB2__FEC_COL */
+							213 0x80000000	/* MX51_PAD_NANDF_RB3__FEC_RX_CLK */
+							293 0x80000000	/* MX51_PAD_NANDF_D9__FEC_RDATA0 */
+							298 0x80000000	/* MX51_PAD_NANDF_D8__FEC_TDATA0 */
+							225 0x80000000	/* MX51_PAD_NANDF_CS2__FEC_TX_ER */
+							231 0x80000000	/* MX51_PAD_NANDF_CS3__FEC_MDC */
+							237 0x80000000	/* MX51_PAD_NANDF_CS4__FEC_TDATA1 */
+							243 0x80000000	/* MX51_PAD_NANDF_CS5__FEC_TDATA2 */
+							250 0x80000000	/* MX51_PAD_NANDF_CS6__FEC_TDATA3 */
+							255 0x80000000	/* MX51_PAD_NANDF_CS7__FEC_TX_EN */
+							260 0x80000000	/* MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK */
+						>;
+					};
+				};
+
+				ecspi1 {
+					pinctrl_ecspi1_1: ecspi1grp-1 {
+						fsl,pins = <
+							398 0x185	/* MX51_PAD_CSPI1_MISO__ECSPI1_MISO */
+							394 0x185	/* MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI */
+							409 0x185	/* MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK */
+						>;
+					};
+				};
+
+				esdhc1 {
+					pinctrl_esdhc1_1: esdhc1grp-1 {
+						fsl,pins = <
+							666 0x400020d5	/* MX51_PAD_SD1_CMD__SD1_CMD */
+							669 0x20d5	/* MX51_PAD_SD1_CLK__SD1_CLK */
+							672 0x20d5	/* MX51_PAD_SD1_DATA0__SD1_DATA0 */
+							678 0x20d5	/* MX51_PAD_SD1_DATA1__SD1_DATA1 */
+							684 0x20d5	/* MX51_PAD_SD1_DATA2__SD1_DATA2 */
+							691 0x20d5	/* MX51_PAD_SD1_DATA3__SD1_DATA3 */
+						>;
+					};
+				};
+
+				esdhc2 {
+					pinctrl_esdhc2_1: esdhc2grp-1 {
+						fsl,pins = <
+							704 0x400020d5	/* MX51_PAD_SD2_CMD__SD2_CMD */
+							707 0x20d5	/* MX51_PAD_SD2_CLK__SD2_CLK */
+							710 0x20d5	/* MX51_PAD_SD2_DATA0__SD2_DATA0 */
+							712 0x20d5	/* MX51_PAD_SD2_DATA1__SD2_DATA1 */
+							715 0x20d5	/* MX51_PAD_SD2_DATA2__SD2_DATA2 */
+							719 0x20d5	/* MX51_PAD_SD2_DATA3__SD2_DATA3 */
+						>;
+					};
+				};
+
+				i2c2 {
+					pinctrl_i2c2_1: i2c2grp-1 {
+						fsl,pins = <
+							449 0x400001ed	/* MX51_PAD_KEY_COL4__I2C2_SCL */
+							454 0x400001ed	/* MX51_PAD_KEY_COL5__I2C2_SDA */
+						>;
+					};
+				};
+
+				uart1 {
+					pinctrl_uart1_1: uart1grp-1 {
+						fsl,pins = <
+							413 0x1c5	/* MX51_PAD_UART1_RXD__UART1_RXD */
+							416 0x1c5	/* MX51_PAD_UART1_TXD__UART1_TXD */
+							418 0x1c5	/* MX51_PAD_UART1_RTS__UART1_RTS */
+							420 0x1c5	/* MX51_PAD_UART1_CTS__UART1_CTS */
+						>;
+					};
+				};
+
+				uart2 {
+					pinctrl_uart2_1: uart2grp-1 {
+						fsl,pins = <
+							423 0x1c5	/* MX51_PAD_UART2_RXD__UART2_RXD */
+							426 0x1c5	/* MX51_PAD_UART2_TXD__UART2_TXD */
+						>;
+					};
+				};
+
+				uart3 {
+					pinctrl_uart3_1: uart3grp-1 {
+						fsl,pins = <
+							54 0x1c5	/* MX51_PAD_EIM_D25__UART3_RXD */
+							59 0x1c5	/* MX51_PAD_EIM_D26__UART3_TXD */
+							65 0x1c5	/* MX51_PAD_EIM_D27__UART3_RTS */
+							49 0x1c5	/* MX51_PAD_EIM_D24__UART3_CTS */
+						>;
+					};
+				};
+			};
+
 			uart1: serial@73fbc000 {
 				compatible = "fsl,imx51-uart", "fsl,imx21-uart";
 				reg = <0x73fbc000 0x4000>;
@@ -219,6 +362,7 @@
 				compatible = "fsl,imx51-sdma", "fsl,imx35-sdma";
 				reg = <0x83fb0000 0x4000>;
 				interrupts = <6>;
+				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx51.bin";
 			};
 
 			cspi@83fc0000 {

arch/arm/boot/dts/imx53-ard.dts

@@ -25,31 +25,66 @@
 		aips@50000000 { /* AIPS1 */
 			spba@50000000 {
 				esdhc@50004000 { /* ESDHC1 */
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_esdhc1_2>;
 					cd-gpios = <&gpio1 1 0>;
 					wp-gpios = <&gpio1 9 0>;
 					status = "okay";
 				};
 			};
 
-			wdog@53f98000 { /* WDOG1 */
-				status = "okay";
-			};
-
 			iomuxc@53fa8000 {
-				compatible = "fsl,imx53-iomuxc-ard";
-				reg = <0x53fa8000 0x4000>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_hog>;
+
+				hog {
+					pinctrl_hog: hoggrp {
+						fsl,pins = <
+							1077 0x80000000	/* MX53_PAD_GPIO_1__GPIO1_1 */
+							1085 0x80000000	/* MX53_PAD_GPIO_9__GPIO1_9 */
+							486  0x80000000	/* MX53_PAD_EIM_EB3__GPIO2_31 */
+							739  0x80000000	/* MX53_PAD_GPIO_10__GPIO4_0 */
+							218  0x80000000	/* MX53_PAD_DISP0_DAT16__GPIO5_10 */
+							226  0x80000000	/* MX53_PAD_DISP0_DAT17__GPIO5_11 */
+							233  0x80000000	/* MX53_PAD_DISP0_DAT18__GPIO5_12 */
+							241  0x80000000	/* MX53_PAD_DISP0_DAT19__GPIO5_13 */
+							429  0x80000000	/* MX53_PAD_EIM_D16__EMI_WEIM_D_16 */
+							435  0x80000000	/* MX53_PAD_EIM_D17__EMI_WEIM_D_17 */
+							441  0x80000000	/* MX53_PAD_EIM_D18__EMI_WEIM_D_18 */
+							448  0x80000000	/* MX53_PAD_EIM_D19__EMI_WEIM_D_19 */
+							456  0x80000000	/* MX53_PAD_EIM_D20__EMI_WEIM_D_20 */
+							464  0x80000000	/* MX53_PAD_EIM_D21__EMI_WEIM_D_21 */
+							471  0x80000000	/* MX53_PAD_EIM_D22__EMI_WEIM_D_22 */
+							477  0x80000000	/* MX53_PAD_EIM_D23__EMI_WEIM_D_23 */
+							492  0x80000000	/* MX53_PAD_EIM_D24__EMI_WEIM_D_24 */
+							500  0x80000000	/* MX53_PAD_EIM_D25__EMI_WEIM_D_25 */
+							508  0x80000000	/* MX53_PAD_EIM_D26__EMI_WEIM_D_26 */
+							516  0x80000000	/* MX53_PAD_EIM_D27__EMI_WEIM_D_27 */
+							524  0x80000000	/* MX53_PAD_EIM_D28__EMI_WEIM_D_28 */
+							532  0x80000000	/* MX53_PAD_EIM_D29__EMI_WEIM_D_29 */
+							540  0x80000000	/* MX53_PAD_EIM_D30__EMI_WEIM_D_30 */
+							548  0x80000000	/* MX53_PAD_EIM_D31__EMI_WEIM_D_31 */
+							637  0x80000000	/* MX53_PAD_EIM_DA0__EMI_NAND_WEIM_DA_0 */
+							642  0x80000000	/* MX53_PAD_EIM_DA1__EMI_NAND_WEIM_DA_1 */
+							647  0x80000000	/* MX53_PAD_EIM_DA2__EMI_NAND_WEIM_DA_2 */
+							652  0x80000000	/* MX53_PAD_EIM_DA3__EMI_NAND_WEIM_DA_3 */
+							657  0x80000000	/* MX53_PAD_EIM_DA4__EMI_NAND_WEIM_DA_4 */
+							662  0x80000000	/* MX53_PAD_EIM_DA5__EMI_NAND_WEIM_DA_5 */
+							667  0x80000000	/* MX53_PAD_EIM_DA6__EMI_NAND_WEIM_DA_6 */
+							611  0x80000000	/* MX53_PAD_EIM_OE__EMI_WEIM_OE */
+							616  0x80000000	/* MX53_PAD_EIM_RW__EMI_WEIM_RW */
+							607  0x80000000	/* MX53_PAD_EIM_CS1__EMI_WEIM_CS_1 */
+						>;
+					};
+				};
 			};
 
 			uart1: serial@53fbc000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_2>;
 				status = "okay";
 			};
 		};
-
-		aips@60000000 {	/* AIPS2 */
-			sdma@63fb0000 {
-				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx53.bin";
-			};
-		};
 	};
 
 	eim-cs1@f4000000 {

arch/arm/boot/dts/imx53-evk.dts

@@ -25,12 +25,16 @@
 		aips@50000000 { /* AIPS1 */
 			spba@50000000 {
 				esdhc@50004000 { /* ESDHC1 */
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_esdhc1_1>;
 					cd-gpios = <&gpio3 13 0>;
 					wp-gpios = <&gpio3 14 0>;
 					status = "okay";
 				};
 
 				ecspi@50010000 { /* ECSPI1 */
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_ecspi1_1>;
 					fsl,spi-num-chipselects = <2>;
 					cs-gpios = <&gpio2 30 0>, <&gpio3 19 0>;
 					status = "okay";
@@ -56,32 +60,45 @@
 				};
 
 				esdhc@50020000 { /* ESDHC3 */
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_esdhc3_1>;
 					cd-gpios = <&gpio3 11 0>;
 					wp-gpios = <&gpio3 12 0>;
 					status = "okay";
 				};
 			};
 
-			wdog@53f98000 { /* WDOG1 */
-				status = "okay";
-			};
-
 			iomuxc@53fa8000 {
-				compatible = "fsl,imx53-iomuxc-evk";
-				reg = <0x53fa8000 0x4000>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_hog>;
+
+				hog {
+					pinctrl_hog: hoggrp {
+						fsl,pins = <
+							424  0x80000000	/* MX53_PAD_EIM_EB2__GPIO2_30 */
+							449  0x80000000	/* MX53_PAD_EIM_D19__GPIO3_19 */
+							693  0x80000000	/* MX53_PAD_EIM_DA11__GPIO3_11 */
+							697  0x80000000	/* MX53_PAD_EIM_DA12__GPIO3_12 */
+							701  0x80000000	/* MX53_PAD_EIM_DA13__GPIO3_13 */
+							705  0x80000000	/* MX53_PAD_EIM_DA14__GPIO3_14 */
+							868  0x80000000	/* MX53_PAD_PATA_DA_0__GPIO7_6 */
+							873  0x80000000	/* MX53_PAD_PATA_DA_1__GPIO7_7 */
+						>;
+					};
+				};
 			};
 
 			uart1: serial@53fbc000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_1>;
 				status = "okay";
 			};
 		};
 
 		aips@60000000 {	/* AIPS2 */
-			sdma@63fb0000 {
-				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx53.bin";
-			};
-
 			i2c@63fc4000 { /* I2C2 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c2_1>;
 				status = "okay";
 
 				pmic: mc13892@08 {
@@ -96,6 +113,8 @@
 			};
 
 			ethernet@63fec000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_fec_1>;
 				phy-mode = "rmii";
 				phy-reset-gpios = <&gpio7 6 0>;
 				status = "okay";

arch/arm/boot/dts/imx53-qsb.dts

@@ -25,6 +25,8 @@
 		aips@50000000 { /* AIPS1 */
 			spba@50000000 {
 				esdhc@50004000 { /* ESDHC1 */
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_esdhc1_1>;
 					cd-gpios = <&gpio3 13 0>;
 					status = "okay";
 				};
@@ -35,32 +37,46 @@
 				};
 
 				esdhc@50020000 { /* ESDHC3 */
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_esdhc3_1>;
 					cd-gpios = <&gpio3 11 0>;
 					wp-gpios = <&gpio3 12 0>;
 					status = "okay";
 				};
 			};
 
-			wdog@53f98000 { /* WDOG1 */
-				status = "okay";
-			};
-
 			iomuxc@53fa8000 {
-				compatible = "fsl,imx53-iomuxc-qsb";
-				reg = <0x53fa8000 0x4000>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_hog>;
+
+				hog {
+					pinctrl_hog: hoggrp {
+						fsl,pins = <
+							1071 0x80000000	/* MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK */
+							1141 0x80000000	/* MX53_PAD_GPIO_8__GPIO1_8 */
+							982  0x80000000	/* MX53_PAD_PATA_DATA14__GPIO2_14 */
+							989  0x80000000	/* MX53_PAD_PATA_DATA15__GPIO2_15 */
+							693  0x80000000	/* MX53_PAD_EIM_DA11__GPIO3_11 */
+							697  0x80000000	/* MX53_PAD_EIM_DA12__GPIO3_12 */
+							701  0x80000000	/* MX53_PAD_EIM_DA13__GPIO3_13 */
+							868  0x80000000	/* MX53_PAD_PATA_DA_0__GPIO7_6 */
+							873  0x80000000	/* MX53_PAD_PATA_DA_1__GPIO7_7 */
+						>;
+					};
+				};
 			};
 
 			uart1: serial@53fbc000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_1>;
 				status = "okay";
 			};
 		};
 
 		aips@60000000 {	/* AIPS2 */
-			sdma@63fb0000 {
-				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx53.bin";
-			};
-
 			i2c@63fc4000 { /* I2C2 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c2_1>;
 				status = "okay";
 
 				sgtl5000: codec@0a {
@@ -72,6 +88,8 @@
 			};
 
 			i2c@63fc8000 { /* I2C1 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1_1>;
 				status = "okay";
 
 				accelerometer: mma8450@1c {
@@ -158,10 +176,14 @@
 			};
 
 			audmux@63fd0000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_audmux_1>;
 				status = "okay";
 			};
 
 			ethernet@63fec000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_fec_1>;
 				phy-mode = "rmii";
 				phy-reset-gpios = <&gpio7 6 0>;
 				status = "okay";

arch/arm/boot/dts/imx53-smd.dts

@@ -25,22 +25,30 @@
 		aips@50000000 { /* AIPS1 */
 			spba@50000000 {
 				esdhc@50004000 { /* ESDHC1 */
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_esdhc1_1>;
 					cd-gpios = <&gpio3 13 0>;
 					wp-gpios = <&gpio4 11 0>;
 					status = "okay";
 				};
 
 				esdhc@50008000 { /* ESDHC2 */
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_esdhc2_1>;
 					non-removable;
 					status = "okay";
 				};
 
 				uart3: serial@5000c000 {
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_uart3_1>;
 					fsl,uart-has-rtscts;
 					status = "okay";
 				};
 
 				ecspi@50010000 { /* ECSPI1 */
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_ecspi1_1>;
 					fsl,spi-num-chipselects = <2>;
 					cs-gpios = <&gpio2 30 0>, <&gpio3 19 0>;
 					status = "okay";
@@ -72,35 +80,49 @@
 				};
 
 				esdhc@50020000 { /* ESDHC3 */
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_esdhc3_1>;
 					non-removable;
 					status = "okay";
 				};
 			};
 
-			wdog@53f98000 { /* WDOG1 */
-				status = "okay";
-			};
-
 			iomuxc@53fa8000 {
-				compatible = "fsl,imx53-iomuxc-smd";
-				reg = <0x53fa8000 0x4000>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_hog>;
+
+				hog {
+					pinctrl_hog: hoggrp {
+						fsl,pins = <
+							982  0x80000000	/* MX53_PAD_PATA_DATA14__GPIO2_14 */
+							989  0x80000000	/* MX53_PAD_PATA_DATA15__GPIO2_15 */
+							424  0x80000000	/* MX53_PAD_EIM_EB2__GPIO2_30 */
+							701  0x80000000	/* MX53_PAD_EIM_DA13__GPIO3_13 */
+							449  0x80000000	/* MX53_PAD_EIM_D19__GPIO3_19 */
+							43   0x80000000	/* MX53_PAD_KEY_ROW2__GPIO4_11 */
+							868  0x80000000	/* MX53_PAD_PATA_DA_0__GPIO7_6 */
+						>;
+					};
+				};
 			};
 
 			uart1: serial@53fbc000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_1>;
 				status = "okay";
 			};
 
 			uart2: serial@53fc0000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart2_1>;
 				status = "okay";
 			};
 		};
 
 		aips@60000000 {	/* AIPS2 */
-			sdma@63fb0000 {
-				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx53.bin";
-			};
-
 			i2c@63fc4000 { /* I2C2 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c2_1>;
 				status = "okay";
 
 				codec: sgtl5000@0a {
@@ -120,6 +142,8 @@
 			};
 
 			i2c@63fc8000 { /* I2C1 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1_1>;
 				status = "okay";
 
 				accelerometer: mma8450@1c {
@@ -139,6 +163,8 @@
 			};
 
 			ethernet@63fec000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_fec_1>;
 				phy-mode = "rmii";
 				phy-reset-gpios = <&gpio7 6 0>;
 				status = "okay";

arch/arm/boot/dts/imx53.dtsi

@@ -135,6 +135,34 @@
 				};
 			};
 
+			usb@53f80000 {
+				compatible = "fsl,imx53-usb", "fsl,imx27-usb";
+				reg = <0x53f80000 0x0200>;
+				interrupts = <18>;
+				status = "disabled";
+			};
+
+			usb@53f80200 {
+				compatible = "fsl,imx53-usb", "fsl,imx27-usb";
+				reg = <0x53f80200 0x0200>;
+				interrupts = <14>;
+				status = "disabled";
+			};
+
+			usb@53f80400 {
+				compatible = "fsl,imx53-usb", "fsl,imx27-usb";
+				reg = <0x53f80400 0x0200>;
+				interrupts = <16>;
+				status = "disabled";
+			};
+
+			usb@53f80600 {
+				compatible = "fsl,imx53-usb", "fsl,imx27-usb";
+				reg = <0x53f80600 0x0200>;
+				interrupts = <17>;
+				status = "disabled";
+			};
+
 			gpio1: gpio@53f84000 {
 				compatible = "fsl,imx53-gpio", "fsl,imx35-gpio";
 				reg = <0x53f84000 0x4000>;
@@ -179,7 +207,6 @@
 				compatible = "fsl,imx53-wdt", "fsl,imx21-wdt";
 				reg = <0x53f98000 0x4000>;
 				interrupts = <58>;
-				status = "disabled";
 			};
 
 			wdog@53f9c000 { /* WDOG2 */
@@ -189,6 +216,161 @@
 				status = "disabled";
 			};
 
+			iomuxc@53fa8000 {
+				compatible = "fsl,imx53-iomuxc";
+				reg = <0x53fa8000 0x4000>;
+
+				audmux {
+					pinctrl_audmux_1: audmuxgrp-1 {
+						fsl,pins = <
+							10 0x80000000	/* MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC */
+							17 0x80000000	/* MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD */
+							23 0x80000000	/* MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS */
+							30 0x80000000	/* MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD */
+						>;
+					};
+				};
+
+				fec {
+					pinctrl_fec_1: fecgrp-1 {
+						fsl,pins = <
+							820 0x80000000	/* MX53_PAD_FEC_MDC__FEC_MDC */
+							779 0x80000000	/* MX53_PAD_FEC_MDIO__FEC_MDIO */
+							786 0x80000000	/* MX53_PAD_FEC_REF_CLK__FEC_TX_CLK */
+							791 0x80000000	/* MX53_PAD_FEC_RX_ER__FEC_RX_ER */
+							796 0x80000000	/* MX53_PAD_FEC_CRS_DV__FEC_RX_DV */
+							799 0x80000000	/* MX53_PAD_FEC_RXD1__FEC_RDATA_1 */
+							804 0x80000000	/* MX53_PAD_FEC_RXD0__FEC_RDATA_0 */
+							808 0x80000000	/* MX53_PAD_FEC_TX_EN__FEC_TX_EN */
+							811 0x80000000	/* MX53_PAD_FEC_TXD1__FEC_TDATA_1 */
+							816 0x80000000	/* MX53_PAD_FEC_TXD0__FEC_TDATA_0 */
+						>;
+					};
+				};
+
+				ecspi1 {
+					pinctrl_ecspi1_1: ecspi1grp-1 {
+						fsl,pins = <
+							433 0x80000000	/* MX53_PAD_EIM_D16__ECSPI1_SCLK */
+							439 0x80000000	/* MX53_PAD_EIM_D17__ECSPI1_MISO */
+							445 0x80000000	/* MX53_PAD_EIM_D18__ECSPI1_MOSI */
+						>;
+					};
+				};
+
+				esdhc1 {
+					pinctrl_esdhc1_1: esdhc1grp-1 {
+						fsl,pins = <
+							995  0x1d5	/* MX53_PAD_SD1_DATA0__ESDHC1_DAT0 */
+							1000 0x1d5	/* MX53_PAD_SD1_DATA1__ESDHC1_DAT1 */
+							1010 0x1d5	/* MX53_PAD_SD1_DATA2__ESDHC1_DAT2 */
+							1024 0x1d5	/* MX53_PAD_SD1_DATA3__ESDHC1_DAT3 */
+							1005 0x1d5	/* MX53_PAD_SD1_CMD__ESDHC1_CMD */
+							1018 0x1d5	/* MX53_PAD_SD1_CLK__ESDHC1_CLK */
+						>;
+					};
+
+					pinctrl_esdhc1_2: esdhc1grp-2 {
+						fsl,pins = <
+							995  0x1d5	/* MX53_PAD_SD1_DATA0__ESDHC1_DAT0 */
+							1000 0x1d5	/* MX53_PAD_SD1_DATA1__ESDHC1_DAT1 */
+							1010 0x1d5	/* MX53_PAD_SD1_DATA2__ESDHC1_DAT2 */
+							1024 0x1d5	/* MX53_PAD_SD1_DATA3__ESDHC1_DAT3 */
+							941  0x1d5	/* MX53_PAD_PATA_DATA8__ESDHC1_DAT4 */
+							948  0x1d5	/* MX53_PAD_PATA_DATA9__ESDHC1_DAT5 */
+							955  0x1d5	/* MX53_PAD_PATA_DATA10__ESDHC1_DAT6 */
+							962  0x1d5	/* MX53_PAD_PATA_DATA11__ESDHC1_DAT7 */
+							1005 0x1d5	/* MX53_PAD_SD1_CMD__ESDHC1_CMD */
+							1018 0x1d5	/* MX53_PAD_SD1_CLK__ESDHC1_CLK */
+						>;
+					};
+				};
+
+				esdhc2 {
+					pinctrl_esdhc2_1: esdhc2grp-1 {
+						fsl,pins = <
+							1038 0x1d5	/* MX53_PAD_SD2_CMD__ESDHC2_CMD */
+							1032 0x1d5	/* MX53_PAD_SD2_CLK__ESDHC2_CLK */
+							1062 0x1d5	/* MX53_PAD_SD2_DATA0__ESDHC2_DAT0 */
+							1056 0x1d5	/* MX53_PAD_SD2_DATA1__ESDHC2_DAT1 */
+							1050 0x1d5	/* MX53_PAD_SD2_DATA2__ESDHC2_DAT2 */
+							1044 0x1d5	/* MX53_PAD_SD2_DATA3__ESDHC2_DAT3 */
+						>;
+					};
+				};
+
+				esdhc3 {
+					pinctrl_esdhc3_1: esdhc3grp-1 {
+						fsl,pins = <
+							943 0x1d5	/* MX53_PAD_PATA_DATA8__ESDHC3_DAT0 */
+							950 0x1d5	/* MX53_PAD_PATA_DATA9__ESDHC3_DAT1 */
+							957 0x1d5	/* MX53_PAD_PATA_DATA10__ESDHC3_DAT2 */
+							964 0x1d5	/* MX53_PAD_PATA_DATA11__ESDHC3_DAT3 */
+							893 0x1d5	/* MX53_PAD_PATA_DATA0__ESDHC3_DAT4 */
+							900 0x1d5	/* MX53_PAD_PATA_DATA1__ESDHC3_DAT5 */
+							906 0x1d5	/* MX53_PAD_PATA_DATA2__ESDHC3_DAT6 */
+							912 0x1d5	/* MX53_PAD_PATA_DATA3__ESDHC3_DAT7 */
+							857 0x1d5	/* MX53_PAD_PATA_RESET_B__ESDHC3_CMD */
+							863 0x1d5	/* MX53_PAD_PATA_IORDY__ESDHC3_CLK */
+						>;
+					};
+				};
+
+				i2c1 {
+					pinctrl_i2c1_1: i2c1grp-1 {
+						fsl,pins = <
+							333 0xc0000000	/* MX53_PAD_CSI0_DAT8__I2C1_SDA */
+							341 0xc0000000	/* MX53_PAD_CSI0_DAT9__I2C1_SCL */
+						>;
+					};
+				};
+
+				i2c2 {
+					pinctrl_i2c2_1: i2c2grp-1 {
+						fsl,pins = <
+							61 0xc0000000	/* MX53_PAD_KEY_ROW3__I2C2_SDA */
+							53 0xc0000000	/* MX53_PAD_KEY_COL3__I2C2_SCL */
+						>;
+					};
+				};
+
+				uart1 {
+					pinctrl_uart1_1: uart1grp-1 {
+						fsl,pins = <
+							346 0x1c5	/* MX53_PAD_CSI0_DAT10__UART1_TXD_MUX */
+							354 0x1c5	/* MX53_PAD_CSI0_DAT11__UART1_RXD_MUX */
+						>;
+					};
+
+					pinctrl_uart1_2: uart1grp-2 {
+						fsl,pins = <
+							828 0x1c5	/* MX53_PAD_PATA_DIOW__UART1_TXD_MUX */
+							832 0x1c5	/* MX53_PAD_PATA_DMACK__UART1_RXD_MUX */
+						>;
+					};
+				};
+
+				uart2 {
+					pinctrl_uart2_1: uart2grp-1 {
+						fsl,pins = <
+							841 0x1c5	/* MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX */
+							836 0x1c5	/* MX53_PAD_PATA_DMARQ__UART2_TXD_MUX */
+						>;
+					};
+				};
+
+				uart3 {
+					pinctrl_uart3_1: uart3grp-1 {
+						fsl,pins = <
+							884 0x1c5	/* MX53_PAD_PATA_CS_0__UART3_TXD_MUX */
+							888 0x1c5	/* MX53_PAD_PATA_CS_1__UART3_RXD_MUX */
+							875 0x1c5	/* MX53_PAD_PATA_DA_1__UART3_CTS */
+							880 0x1c5	/* MX53_PAD_PATA_DA_2__UART3_RTS */
+						>;
+					};
+				};
+			};
+
 			uart1: serial@53fbc000 {
 				compatible = "fsl,imx53-uart", "fsl,imx21-uart";
 				reg = <0x53fbc000 0x4000>;
@@ -203,6 +385,20 @@
 				status = "disabled";
 			};
 
+			can1: can@53fc8000 {
+				compatible = "fsl,imx53-flexcan", "fsl,p1010-flexcan";
+				reg = <0x53fc8000 0x4000>;
+				interrupts = <82>;
+				status = "disabled";
+			};
+
+			can2: can@53fcc000 {
+				compatible = "fsl,imx53-flexcan", "fsl,p1010-flexcan";
+				reg = <0x53fcc000 0x4000>;
+				interrupts = <83>;
+				status = "disabled";
+			};
+
 			gpio5: gpio@53fdc000 {
 				compatible = "fsl,imx53-gpio", "fsl,imx35-gpio";
 				reg = <0x53fdc000 0x4000>;
@@ -277,6 +473,7 @@
 				compatible = "fsl,imx53-sdma", "fsl,imx35-sdma";
 				reg = <0x63fb0000 0x4000>;
 				interrupts = <6>;
+				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx53.bin";
 			};
 
 			cspi@63fc0000 {

arch/arm/boot/dts/imx6q-arm2.dts

@@ -28,8 +28,27 @@
 			status = "disabled"; /* gpmi nand conflicts with SD */
 		};
 
+		aips-bus@02000000 { /* AIPS1 */
+			iomuxc@020e0000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_hog>;
+
+				hog {
+					pinctrl_hog: hoggrp {
+						fsl,pins = <
+							176  0x80000000	/* MX6Q_PAD_EIM_D25__GPIO_3_25 */
+							1363 0x80000000	/* MX6Q_PAD_NANDF_CS0__GPIO_6_11 */
+							1369 0x80000000 /* MX6Q_PAD_NANDF_CS1__GPIO_6_14 */
+						>;
+					};
+				};
+			};
+		};
+
 		aips-bus@02100000 { /* AIPS2 */
 			ethernet@02188000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_enet_2>;
 				phy-mode = "rgmii";
 				status = "okay";
 			};
@@ -52,6 +71,8 @@
 			};
 
 			uart4: serial@021f0000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart4_1>;
 				status = "okay";
 			};
 		};

arch/arm/boot/dts/imx6q-sabrelite.dts

@@ -46,15 +46,20 @@
 
 			iomuxc@020e0000 {
 				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_gpio_hog>;
+				pinctrl-0 = <&pinctrl_hog>;
 
-				gpios {
-					pinctrl_gpio_hog: gpiohog {
+				hog {
+					pinctrl_hog: hoggrp {
 						fsl,pins = <
-							   144  0x80000000	/* MX6Q_PAD_EIM_D22__GPIO_3_22 */
-							   121  0x80000000	/* MX6Q_PAD_EIM_D19__GPIO_3_19 */
-							   953  0x80000000	/* MX6Q_PAD_GPIO_0__CCM_CLKO */
-							   >;
+							1450 0x80000000	/* MX6Q_PAD_NANDF_D6__GPIO_2_6 */
+							1458 0x80000000	/* MX6Q_PAD_NANDF_D7__GPIO_2_7 */
+							121  0x80000000	/* MX6Q_PAD_EIM_D19__GPIO_3_19 */
+							144  0x80000000	/* MX6Q_PAD_EIM_D22__GPIO_3_22 */
+							152  0x80000000	/* MX6Q_PAD_EIM_D23__GPIO_3_23 */
+							1262 0x80000000 /* MX6Q_PAD_SD3_DAT5__GPIO_7_0 */
+							1270 0x1f0b0	/* MX6Q_PAD_SD3_DAT4__GPIO_7_1 */
+							953  0x80000000	/* MX6Q_PAD_GPIO_0__CCM_CLKO */
+						>;
 					};
 				};
 			};
@@ -63,6 +68,9 @@
 		aips-bus@02100000 { /* AIPS2 */
 			usb@02184000 { /* USB OTG */
 				vbus-supply = <&reg_usb_otg_vbus>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_usbotg_1>;
+				disable-over-current;
 				status = "okay";
 			};
 
@@ -71,12 +79,16 @@
 			};
 
 			ethernet@02188000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_enet_1>;
 				phy-mode = "rgmii";
 				phy-reset-gpios = <&gpio3 23 0>;
 				status = "okay";
 			};
 
 			usdhc@02198000 { /* uSDHC3 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_usdhc3_2>;
 				cd-gpios = <&gpio7 0 0>;
 				wp-gpios = <&gpio7 1 0>;
 				vmmc-supply = <&reg_3p3v>;
@@ -84,6 +96,8 @@
 			};
 
 			usdhc@0219c000 { /* uSDHC4 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_usdhc4_2>;
 				cd-gpios = <&gpio2 6 0>;
 				wp-gpios = <&gpio2 7 0>;
 				vmmc-supply = <&reg_3p3v>;
@@ -99,7 +113,7 @@
 			uart2: serial@021e8000 {
 				status = "okay";
 				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_serial2_1>;
+				pinctrl-0 = <&pinctrl_uart2_1>;
 			};
 
 			i2c@021a0000 { /* I2C1 */
@@ -111,6 +125,7 @@
 				codec: sgtl5000@0a {
 					compatible = "fsl,sgtl5000";
 					reg = <0x0a>;
+					clocks = <&clks 169>;
 					VDDA-supply = <&reg_2p5v>;
 					VDDIO-supply = <&reg_3p3v>;
 				};

arch/arm/boot/dts/imx6q-sabresd.dts

@@ -22,28 +22,51 @@
 	};
 
 	soc {
-
 		aips-bus@02000000 { /* AIPS1 */
 			spba-bus@02000000 {
 				uart1: serial@02020000 {
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_uart1_1>;
 					status = "okay";
 				};
 			};
+
+			iomuxc@020e0000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_hog>;
+
+				hog {
+					pinctrl_hog: hoggrp {
+						fsl,pins = <
+							1402 0x80000000	/* MX6Q_PAD_NANDF_D0__GPIO_2_0 */
+							1410 0x80000000	/* MX6Q_PAD_NANDF_D1__GPIO_2_1 */
+							1418 0x80000000	/* MX6Q_PAD_NANDF_D2__GPIO_2_2 */
+							1426 0x80000000	/* MX6Q_PAD_NANDF_D3__GPIO_2_3 */
+						>;
+					};
+				};
+			};
 		};
 
 		aips-bus@02100000 { /* AIPS2 */
 			ethernet@02188000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_enet_1>;
 				phy-mode = "rgmii";
 				status = "okay";
 			};
 
 			usdhc@02194000 { /* uSDHC2 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_usdhc2_1>;
 				cd-gpios = <&gpio2 2 0>;
 				wp-gpios = <&gpio2 3 0>;
 				status = "okay";
 			};
 
 			usdhc@02198000 { /* uSDHC3 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_usdhc3_1>;
 				cd-gpios = <&gpio2 0 0>;
 				wp-gpios = <&gpio2 1 0>;
 				status = "okay";

arch/arm/boot/dts/imx6q.dtsi

@@ -97,18 +97,23 @@
 		dma-apbh@00110000 {
 			compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x00110000 0x2000>;
+			clocks = <&clks 106>;
 		};
 
 		gpmi-nand@00112000 {
-		       compatible = "fsl,imx6q-gpmi-nand";
-		       #address-cells = <1>;
-		       #size-cells = <1>;
-		       reg = <0x00112000 0x2000>, <0x00114000 0x2000>;
-		       reg-names = "gpmi-nand", "bch";
-		       interrupts = <0 13 0x04>, <0 15 0x04>;
-		       interrupt-names = "gpmi-dma", "bch";
-		       fsl,gpmi-dma-channel = <0>;
-		       status = "disabled";
+			compatible = "fsl,imx6q-gpmi-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x00112000 0x2000>, <0x00114000 0x2000>;
+			reg-names = "gpmi-nand", "bch";
+			interrupts = <0 13 0x04>, <0 15 0x04>;
+			interrupt-names = "gpmi-dma", "bch";
+			clocks = <&clks 152>, <&clks 153>, <&clks 151>,
+				 <&clks 150>, <&clks 149>;
+			clock-names = "gpmi_io", "gpmi_apb", "gpmi_bch",
+				      "gpmi_bch_apb", "per1_bch";
+			fsl,gpmi-dma-channel = <0>;
+			status = "disabled";
 		};
 
 		timer@00a00600 {
@@ -150,6 +155,8 @@
 					compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
 					reg = <0x02008000 0x4000>;
 					interrupts = <0 31 0x04>;
+					clocks = <&clks 112>, <&clks 112>;
+					clock-names = "ipg", "per";
 					status = "disabled";
 				};
 
@@ -159,6 +166,8 @@
 					compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
 					reg = <0x0200c000 0x4000>;
 					interrupts = <0 32 0x04>;
+					clocks = <&clks 113>, <&clks 113>;
+					clock-names = "ipg", "per";
 					status = "disabled";
 				};
 
@@ -168,6 +177,8 @@
 					compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
 					reg = <0x02010000 0x4000>;
 					interrupts = <0 33 0x04>;
+					clocks = <&clks 114>, <&clks 114>;
+					clock-names = "ipg", "per";
 					status = "disabled";
 				};
 
@@ -177,6 +188,8 @@
 					compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
 					reg = <0x02014000 0x4000>;
 					interrupts = <0 34 0x04>;
+					clocks = <&clks 115>, <&clks 115>;
+					clock-names = "ipg", "per";
 					status = "disabled";
 				};
 
@@ -186,6 +199,8 @@
 					compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
 					reg = <0x02018000 0x4000>;
 					interrupts = <0 35 0x04>;
+					clocks = <&clks 116>, <&clks 116>;
+					clock-names = "ipg", "per";
 					status = "disabled";
 				};
 
@@ -193,6 +208,8 @@
 					compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02020000 0x4000>;
 					interrupts = <0 26 0x04>;
+					clocks = <&clks 160>, <&clks 161>;
+					clock-names = "ipg", "per";
 					status = "disabled";
 				};
 
@@ -205,6 +222,7 @@
 					compatible = "fsl,imx6q-ssi","fsl,imx21-ssi";
 					reg = <0x02028000 0x4000>;
 					interrupts = <0 46 0x04>;
+					clocks = <&clks 178>;
 					fsl,fifo-depth = <15>;
 					fsl,ssi-dma-events = <38 37>;
 					status = "disabled";
@@ -214,6 +232,7 @@
 					compatible = "fsl,imx6q-ssi","fsl,imx21-ssi";
 					reg = <0x0202c000 0x4000>;
 					interrupts = <0 47 0x04>;
+					clocks = <&clks 179>;
 					fsl,fifo-depth = <15>;
 					fsl,ssi-dma-events = <42 41>;
 					status = "disabled";
@@ -223,6 +242,7 @@
 					compatible = "fsl,imx6q-ssi","fsl,imx21-ssi";
 					reg = <0x02030000 0x4000>;
 					interrupts = <0 48 0x04>;
+					clocks = <&clks 180>;
 					fsl,fifo-depth = <15>;
 					fsl,ssi-dma-events = <46 45>;
 					status = "disabled";
@@ -362,20 +382,22 @@
 				compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt";
 				reg = <0x020bc000 0x4000>;
 				interrupts = <0 80 0x04>;
-				status = "disabled";
+				clocks = <&clks 0>;
 			};
 
 			wdog@020c0000 { /* WDOG2 */
 				compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt";
 				reg = <0x020c0000 0x4000>;
 				interrupts = <0 81 0x04>;
+				clocks = <&clks 0>;
 				status = "disabled";
 			};
 
-			ccm@020c4000 {
+			clks: ccm@020c4000 {
 				compatible = "fsl,imx6q-ccm";
 				reg = <0x020c4000 0x4000>;
 				interrupts = <0 87 0x04 0 88 0x04>;
+				#clock-cells = <1>;
 			};
 
 			anatop@020c8000 {
@@ -472,12 +494,14 @@
 				compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy";
 				reg = <0x020c9000 0x1000>;
 				interrupts = <0 44 0x04>;
+				clocks = <&clks 182>;
 			};
 
 			usbphy2: usbphy@020ca000 {
 				compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy";
 				reg = <0x020ca000 0x1000>;
 				interrupts = <0 45 0x04>;
+				clocks = <&clks 183>;
 			};
 
 			snvs@020cc000 {
@@ -514,86 +538,207 @@
 				/* shared pinctrl settings */
 				audmux {
 					pinctrl_audmux_1: audmux-1 {
-						fsl,pins = <18   0x80000000	/* MX6Q_PAD_SD2_DAT0__AUDMUX_AUD4_RXD */
-							    1586 0x80000000	/* MX6Q_PAD_SD2_DAT3__AUDMUX_AUD4_TXC */
-							    11   0x80000000	/* MX6Q_PAD_SD2_DAT2__AUDMUX_AUD4_TXD */
-							    3    0x80000000>;	/* MX6Q_PAD_SD2_DAT1__AUDMUX_AUD4_TXFS */
+						fsl,pins = <
+							18   0x80000000	/* MX6Q_PAD_SD2_DAT0__AUDMUX_AUD4_RXD */
+							1586 0x80000000	/* MX6Q_PAD_SD2_DAT3__AUDMUX_AUD4_TXC */
+							11   0x80000000	/* MX6Q_PAD_SD2_DAT2__AUDMUX_AUD4_TXD */
+							3    0x80000000	/* MX6Q_PAD_SD2_DAT1__AUDMUX_AUD4_TXFS */
+						>;
+					};
+				};
+
+				ecspi1 {
+					pinctrl_ecspi1_1: ecspi1grp-1 {
+						fsl,pins = <
+							101 0x100b1	/* MX6Q_PAD_EIM_D17__ECSPI1_MISO */
+							109 0x100b1	/* MX6Q_PAD_EIM_D18__ECSPI1_MOSI */
+							94  0x100b1	/* MX6Q_PAD_EIM_D16__ECSPI1_SCLK */
+						>;
+					};
+				};
+
+				enet {
+					pinctrl_enet_1: enetgrp-1 {
+						fsl,pins = <
+							695 0x1b0b0	/* MX6Q_PAD_ENET_MDIO__ENET_MDIO */
+							756 0x1b0b0	/* MX6Q_PAD_ENET_MDC__ENET_MDC */
+							24  0x1b0b0	/* MX6Q_PAD_RGMII_TXC__ENET_RGMII_TXC */
+							30  0x1b0b0	/* MX6Q_PAD_RGMII_TD0__ENET_RGMII_TD0 */
+							34  0x1b0b0	/* MX6Q_PAD_RGMII_TD1__ENET_RGMII_TD1 */
+							39  0x1b0b0	/* MX6Q_PAD_RGMII_TD2__ENET_RGMII_TD2 */
+							44  0x1b0b0	/* MX6Q_PAD_RGMII_TD3__ENET_RGMII_TD3 */
+							56  0x1b0b0	/* MX6Q_PAD_RGMII_TX_CTL__RGMII_TX_CTL */
+							702 0x1b0b0	/* MX6Q_PAD_ENET_REF_CLK__ENET_TX_CLK */
+							74  0x1b0b0	/* MX6Q_PAD_RGMII_RXC__ENET_RGMII_RXC */
+							52  0x1b0b0	/* MX6Q_PAD_RGMII_RD0__ENET_RGMII_RD0 */
+							61  0x1b0b0	/* MX6Q_PAD_RGMII_RD1__ENET_RGMII_RD1 */
+							66  0x1b0b0	/* MX6Q_PAD_RGMII_RD2__ENET_RGMII_RD2 */
+							70  0x1b0b0	/* MX6Q_PAD_RGMII_RD3__ENET_RGMII_RD3 */
+							48  0x1b0b0	/* MX6Q_PAD_RGMII_RX_CTL__RGMII_RX_CTL */
+						>;
+					};
+
+					pinctrl_enet_2: enetgrp-2 {
+						fsl,pins = <
+							890 0x1b0b0	/* MX6Q_PAD_KEY_COL1__ENET_MDIO */
+							909 0x1b0b0	/* MX6Q_PAD_KEY_COL2__ENET_MDC */
+							24  0x1b0b0	/* MX6Q_PAD_RGMII_TXC__ENET_RGMII_TXC */
+							30  0x1b0b0	/* MX6Q_PAD_RGMII_TD0__ENET_RGMII_TD0 */
+							34  0x1b0b0	/* MX6Q_PAD_RGMII_TD1__ENET_RGMII_TD1 */
+							39  0x1b0b0	/* MX6Q_PAD_RGMII_TD2__ENET_RGMII_TD2 */
+							44  0x1b0b0	/* MX6Q_PAD_RGMII_TD3__ENET_RGMII_TD3 */
+							56  0x1b0b0	/* MX6Q_PAD_RGMII_TX_CTL__RGMII_TX_CTL */
+							702 0x1b0b0	/* MX6Q_PAD_ENET_REF_CLK__ENET_TX_CLK */
+							74  0x1b0b0	/* MX6Q_PAD_RGMII_RXC__ENET_RGMII_RXC */
+							52  0x1b0b0	/* MX6Q_PAD_RGMII_RD0__ENET_RGMII_RD0 */
+							61  0x1b0b0	/* MX6Q_PAD_RGMII_RD1__ENET_RGMII_RD1 */
+							66  0x1b0b0	/* MX6Q_PAD_RGMII_RD2__ENET_RGMII_RD2 */
+							70  0x1b0b0	/* MX6Q_PAD_RGMII_RD3__ENET_RGMII_RD3 */
+							48  0x1b0b0	/* MX6Q_PAD_RGMII_RX_CTL__RGMII_RX_CTL */
+						>;
 					};
 				};
 
 				gpmi-nand {
 					pinctrl_gpmi_nand_1: gpmi-nand-1 {
-						fsl,pins = <1328 0xb0b1		/* MX6Q_PAD_NANDF_CLE__RAWNAND_CLE */
-							    1336 0xb0b1		/* MX6Q_PAD_NANDF_ALE__RAWNAND_ALE */
-							    1344 0xb0b1		/* MX6Q_PAD_NANDF_WP_B__RAWNAND_RESETN */
-							    1352 0xb000		/* MX6Q_PAD_NANDF_RB0__RAWNAND_READY0 */
-							    1360 0xb0b1		/* MX6Q_PAD_NANDF_CS0__RAWNAND_CE0N */
-							    1365 0xb0b1		/* MX6Q_PAD_NANDF_CS1__RAWNAND_CE1N */
-							    1371 0xb0b1		/* MX6Q_PAD_NANDF_CS2__RAWNAND_CE2N */
-							    1378 0xb0b1		/* MX6Q_PAD_NANDF_CS3__RAWNAND_CE3N */
-							    1387 0xb0b1		/* MX6Q_PAD_SD4_CMD__RAWNAND_RDN */
-							    1393 0xb0b1		/* MX6Q_PAD_SD4_CLK__RAWNAND_WRN */
-							    1397 0xb0b1		/* MX6Q_PAD_NANDF_D0__RAWNAND_D0 */
-							    1405 0xb0b1		/* MX6Q_PAD_NANDF_D1__RAWNAND_D1 */
-							    1413 0xb0b1		/* MX6Q_PAD_NANDF_D2__RAWNAND_D2 */
-							    1421 0xb0b1		/* MX6Q_PAD_NANDF_D3__RAWNAND_D3 */
-							    1429 0xb0b1		/* MX6Q_PAD_NANDF_D4__RAWNAND_D4 */
-							    1437 0xb0b1		/* MX6Q_PAD_NANDF_D5__RAWNAND_D5 */
-							    1445 0xb0b1		/* MX6Q_PAD_NANDF_D6__RAWNAND_D6 */
-							    1453 0xb0b1		/* MX6Q_PAD_NANDF_D7__RAWNAND_D7 */
-							    1463 0x00b1>;	/* MX6Q_PAD_SD4_DAT0__RAWNAND_DQS */
+						fsl,pins = <
+							1328 0xb0b1	/* MX6Q_PAD_NANDF_CLE__RAWNAND_CLE */
+							1336 0xb0b1	/* MX6Q_PAD_NANDF_ALE__RAWNAND_ALE */
+							1344 0xb0b1	/* MX6Q_PAD_NANDF_WP_B__RAWNAND_RESETN */
+							1352 0xb000	/* MX6Q_PAD_NANDF_RB0__RAWNAND_READY0 */
+							1360 0xb0b1	/* MX6Q_PAD_NANDF_CS0__RAWNAND_CE0N */
+							1365 0xb0b1	/* MX6Q_PAD_NANDF_CS1__RAWNAND_CE1N */
+							1371 0xb0b1	/* MX6Q_PAD_NANDF_CS2__RAWNAND_CE2N */
+							1378 0xb0b1	/* MX6Q_PAD_NANDF_CS3__RAWNAND_CE3N */
+							1387 0xb0b1	/* MX6Q_PAD_SD4_CMD__RAWNAND_RDN */
+							1393 0xb0b1	/* MX6Q_PAD_SD4_CLK__RAWNAND_WRN */
+							1397 0xb0b1	/* MX6Q_PAD_NANDF_D0__RAWNAND_D0 */
+							1405 0xb0b1	/* MX6Q_PAD_NANDF_D1__RAWNAND_D1 */
+							1413 0xb0b1	/* MX6Q_PAD_NANDF_D2__RAWNAND_D2 */
+							1421 0xb0b1	/* MX6Q_PAD_NANDF_D3__RAWNAND_D3 */
+							1429 0xb0b1	/* MX6Q_PAD_NANDF_D4__RAWNAND_D4 */
+							1437 0xb0b1	/* MX6Q_PAD_NANDF_D5__RAWNAND_D5 */
+							1445 0xb0b1	/* MX6Q_PAD_NANDF_D6__RAWNAND_D6 */
+							1453 0xb0b1	/* MX6Q_PAD_NANDF_D7__RAWNAND_D7 */
+							1463 0x00b1	/* MX6Q_PAD_SD4_DAT0__RAWNAND_DQS */
+						>;
 					};
 				};
 
 				i2c1 {
 					pinctrl_i2c1_1: i2c1grp-1 {
-						fsl,pins = <137 0x4001b8b1	/* MX6Q_PAD_EIM_D21__I2C1_SCL */
-							    196 0x4001b8b1>;	/* MX6Q_PAD_EIM_D28__I2C1_SDA */
+						fsl,pins = <
+							137 0x4001b8b1	/* MX6Q_PAD_EIM_D21__I2C1_SCL */
+							196 0x4001b8b1	/* MX6Q_PAD_EIM_D28__I2C1_SDA */
+						>;
+					};
+				};
+
+				uart1 {
+					pinctrl_uart1_1: uart1grp-1 {
+						fsl,pins = <
+							1140 0x1b0b1	/* MX6Q_PAD_CSI0_DAT10__UART1_TXD */
+							1148 0x1b0b1	/* MX6Q_PAD_CSI0_DAT11__UART1_RXD */
+						>;
 					};
 				};
 
-				serial2 {
-					pinctrl_serial2_1: serial2grp-1 {
-						fsl,pins = <183 0x1b0b1		/* MX6Q_PAD_EIM_D26__UART2_TXD */
-							    191 0x1b0b1>;	/* MX6Q_PAD_EIM_D27__UART2_RXD */
+				uart2 {
+					pinctrl_uart2_1: uart2grp-1 {
+						fsl,pins = <
+							183 0x1b0b1	/* MX6Q_PAD_EIM_D26__UART2_TXD */
+							191 0x1b0b1	/* MX6Q_PAD_EIM_D27__UART2_RXD */
+						>;
+					};
+				};
+
+				uart4 {
+					pinctrl_uart4_1: uart4grp-1 {
+						fsl,pins = <
+							877 0x1b0b1	/* MX6Q_PAD_KEY_COL0__UART4_TXD */
+							885 0x1b0b1	/* MX6Q_PAD_KEY_ROW0__UART4_RXD */
+						>;
+					};
+				};
+
+				usbotg {
+					pinctrl_usbotg_1: usbotggrp-1 {
+						fsl,pins = <
+							1592 0x17059	/* MX6Q_PAD_GPIO_1__ANATOP_USBOTG_ID */
+						>;
+					};
+				};
+
+				usdhc2 {
+					pinctrl_usdhc2_1: usdhc2grp-1 {
+						fsl,pins = <
+							1577 0x17059	/* MX6Q_PAD_SD2_CMD__USDHC2_CMD */
+							1569 0x10059	/* MX6Q_PAD_SD2_CLK__USDHC2_CLK */
+							16   0x17059	/* MX6Q_PAD_SD2_DAT0__USDHC2_DAT0 */
+							0    0x17059	/* MX6Q_PAD_SD2_DAT1__USDHC2_DAT1 */
+							8    0x17059	/* MX6Q_PAD_SD2_DAT2__USDHC2_DAT2 */
+							1583 0x17059	/* MX6Q_PAD_SD2_DAT3__USDHC2_DAT3 */
+							1430 0x17059	/* MX6Q_PAD_NANDF_D4__USDHC2_DAT4 */
+							1438 0x17059	/* MX6Q_PAD_NANDF_D5__USDHC2_DAT5 */
+							1446 0x17059	/* MX6Q_PAD_NANDF_D6__USDHC2_DAT6 */
+							1454 0x17059	/* MX6Q_PAD_NANDF_D7__USDHC2_DAT7 */
+						>;
 					};
 				};
 
 				usdhc3 {
 					pinctrl_usdhc3_1: usdhc3grp-1 {
-						fsl,pins = <1273 0x17059	/* MX6Q_PAD_SD3_CMD__USDHC3_CMD */
-							    1281 0x10059	/* MX6Q_PAD_SD3_CLK__USDHC3_CLK	*/
-							    1289 0x17059	/* MX6Q_PAD_SD3_DAT0__USDHC3_DAT0 */
-							    1297 0x17059	/* MX6Q_PAD_SD3_DAT1__USDHC3_DAT1 */
-							    1305 0x17059	/* MX6Q_PAD_SD3_DAT2__USDHC3_DAT2 */
-							    1312 0x17059	/* MX6Q_PAD_SD3_DAT3__USDHC3_DAT3 */
-							    1265 0x17059	/* MX6Q_PAD_SD3_DAT4__USDHC3_DAT4 */
-							    1257 0x17059	/* MX6Q_PAD_SD3_DAT5__USDHC3_DAT5 */
-							    1249 0x17059	/* MX6Q_PAD_SD3_DAT6__USDHC3_DAT6 */
-							    1241 0x17059>;	/* MX6Q_PAD_SD3_DAT7__USDHC3_DAT7 */
+						fsl,pins = <
+							1273 0x17059	/* MX6Q_PAD_SD3_CMD__USDHC3_CMD */
+							1281 0x10059	/* MX6Q_PAD_SD3_CLK__USDHC3_CLK	*/
+							1289 0x17059	/* MX6Q_PAD_SD3_DAT0__USDHC3_DAT0 */
+							1297 0x17059	/* MX6Q_PAD_SD3_DAT1__USDHC3_DAT1 */
+							1305 0x17059	/* MX6Q_PAD_SD3_DAT2__USDHC3_DAT2 */
+							1312 0x17059	/* MX6Q_PAD_SD3_DAT3__USDHC3_DAT3 */
+							1265 0x17059	/* MX6Q_PAD_SD3_DAT4__USDHC3_DAT4 */
+							1257 0x17059	/* MX6Q_PAD_SD3_DAT5__USDHC3_DAT5 */
+							1249 0x17059	/* MX6Q_PAD_SD3_DAT6__USDHC3_DAT6 */
+							1241 0x17059	/* MX6Q_PAD_SD3_DAT7__USDHC3_DAT7 */
+						>;
+					};
+
+					pinctrl_usdhc3_2: usdhc3grp-2 {
+						fsl,pins = <
+							1273 0x17059	/* MX6Q_PAD_SD3_CMD__USDHC3_CMD */
+							1281 0x10059	/* MX6Q_PAD_SD3_CLK__USDHC3_CLK	*/
+							1289 0x17059	/* MX6Q_PAD_SD3_DAT0__USDHC3_DAT0 */
+							1297 0x17059	/* MX6Q_PAD_SD3_DAT1__USDHC3_DAT1 */
+							1305 0x17059	/* MX6Q_PAD_SD3_DAT2__USDHC3_DAT2 */
+							1312 0x17059	/* MX6Q_PAD_SD3_DAT3__USDHC3_DAT3 */
+						>;
 					};
 				};
 
 				usdhc4 {
 					pinctrl_usdhc4_1: usdhc4grp-1 {
-						fsl,pins = <1386 0x17059	/* MX6Q_PAD_SD4_CMD__USDHC4_CMD */
-							    1392 0x10059	/* MX6Q_PAD_SD4_CLK__USDHC4_CLK	*/
-							    1462 0x17059	/* MX6Q_PAD_SD4_DAT0__USDHC4_DAT0 */
-							    1470 0x17059	/* MX6Q_PAD_SD4_DAT1__USDHC4_DAT1 */
-							    1478 0x17059	/* MX6Q_PAD_SD4_DAT2__USDHC4_DAT2 */
-							    1486 0x17059	/* MX6Q_PAD_SD4_DAT3__USDHC4_DAT3 */
-							    1493 0x17059	/* MX6Q_PAD_SD4_DAT4__USDHC4_DAT4 */
-							    1501 0x17059	/* MX6Q_PAD_SD4_DAT5__USDHC4_DAT5 */
-							    1509 0x17059	/* MX6Q_PAD_SD4_DAT6__USDHC4_DAT6 */
-							    1517 0x17059>;	/* MX6Q_PAD_SD4_DAT7__USDHC4_DAT7 */
+						fsl,pins = <
+							1386 0x17059	/* MX6Q_PAD_SD4_CMD__USDHC4_CMD */
+							1392 0x10059	/* MX6Q_PAD_SD4_CLK__USDHC4_CLK	*/
+							1462 0x17059	/* MX6Q_PAD_SD4_DAT0__USDHC4_DAT0 */
+							1470 0x17059	/* MX6Q_PAD_SD4_DAT1__USDHC4_DAT1 */
+							1478 0x17059	/* MX6Q_PAD_SD4_DAT2__USDHC4_DAT2 */
+							1486 0x17059	/* MX6Q_PAD_SD4_DAT3__USDHC4_DAT3 */
+							1493 0x17059	/* MX6Q_PAD_SD4_DAT4__USDHC4_DAT4 */
+							1501 0x17059	/* MX6Q_PAD_SD4_DAT5__USDHC4_DAT5 */
+							1509 0x17059	/* MX6Q_PAD_SD4_DAT6__USDHC4_DAT6 */
+							1517 0x17059	/* MX6Q_PAD_SD4_DAT7__USDHC4_DAT7 */
+						>;
 					};
-				};
 
-				ecspi1 {
-					pinctrl_ecspi1_1: ecspi1grp-1 {
-						fsl,pins = <101 0x100b1		/* MX6Q_PAD_EIM_D17__ECSPI1_MISO */
-							    109 0x100b1		/* MX6Q_PAD_EIM_D18__ECSPI1_MOSI */
-							    94  0x100b1>;	/* MX6Q_PAD_EIM_D16__ECSPI1_SCLK */
+					pinctrl_usdhc4_2: usdhc4grp-2 {
+						fsl,pins = <
+							1386 0x17059	/* MX6Q_PAD_SD4_CMD__USDHC4_CMD */
+							1392 0x10059	/* MX6Q_PAD_SD4_CLK__USDHC4_CLK	*/
+							1462 0x17059	/* MX6Q_PAD_SD4_DAT0__USDHC4_DAT0 */
+							1470 0x17059	/* MX6Q_PAD_SD4_DAT1__USDHC4_DAT1 */
+							1478 0x17059	/* MX6Q_PAD_SD4_DAT2__USDHC4_DAT2 */
+							1486 0x17059	/* MX6Q_PAD_SD4_DAT3__USDHC4_DAT3 */
+						>;
 					};
 				};
 			};
@@ -612,6 +757,9 @@
 				compatible = "fsl,imx6q-sdma", "fsl,imx35-sdma";
 				reg = <0x020ec000 0x4000>;
 				interrupts = <0 2 0x04>;
+				clocks = <&clks 155>, <&clks 155>;
+				clock-names = "ipg", "ahb";
+				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6q-to1.bin";
 			};
 		};
 
@@ -635,7 +783,9 @@
 				compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
 				reg = <0x02184000 0x200>;
 				interrupts = <0 43 0x04>;
+				clocks = <&clks 162>;
 				fsl,usbphy = <&usbphy1>;
+				fsl,usbmisc = <&usbmisc 0>;
 				status = "disabled";
 			};
 
@@ -643,7 +793,9 @@
 				compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
 				reg = <0x02184200 0x200>;
 				interrupts = <0 40 0x04>;
+				clocks = <&clks 162>;
 				fsl,usbphy = <&usbphy2>;
+				fsl,usbmisc = <&usbmisc 1>;
 				status = "disabled";
 			};
 
@@ -651,6 +803,8 @@
 				compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
 				reg = <0x02184400 0x200>;
 				interrupts = <0 41 0x04>;
+				clocks = <&clks 162>;
+				fsl,usbmisc = <&usbmisc 2>;
 				status = "disabled";
 			};
 
@@ -658,13 +812,24 @@
 				compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
 				reg = <0x02184600 0x200>;
 				interrupts = <0 42 0x04>;
+				clocks = <&clks 162>;
+				fsl,usbmisc = <&usbmisc 3>;
 				status = "disabled";
 			};
 
+			usbmisc: usbmisc@02184800 {
+				#index-cells = <1>;
+				compatible = "fsl,imx6q-usbmisc";
+				reg = <0x02184800 0x200>;
+				clocks = <&clks 162>;
+			};
+
 			ethernet@02188000 {
 				compatible = "fsl,imx6q-fec";
 				reg = <0x02188000 0x4000>;
 				interrupts = <0 118 0x04 0 119 0x04>;
+				clocks = <&clks 117>, <&clks 117>;
+				clock-names = "ipg", "ahb";
 				status = "disabled";
 			};
 
@@ -677,6 +842,8 @@
 				compatible = "fsl,imx6q-usdhc";
 				reg = <0x02190000 0x4000>;
 				interrupts = <0 22 0x04>;
+				clocks = <&clks 163>, <&clks 163>, <&clks 163>;
+				clock-names = "ipg", "ahb", "per";
 				status = "disabled";
 			};
 
@@ -684,6 +851,8 @@
 				compatible = "fsl,imx6q-usdhc";
 				reg = <0x02194000 0x4000>;
 				interrupts = <0 23 0x04>;
+				clocks = <&clks 164>, <&clks 164>, <&clks 164>;
+				clock-names = "ipg", "ahb", "per";
 				status = "disabled";
 			};
 
@@ -691,6 +860,8 @@
 				compatible = "fsl,imx6q-usdhc";
 				reg = <0x02198000 0x4000>;
 				interrupts = <0 24 0x04>;
+				clocks = <&clks 165>, <&clks 165>, <&clks 165>;
+				clock-names = "ipg", "ahb", "per";
 				status = "disabled";
 			};
 
@@ -698,6 +869,8 @@
 				compatible = "fsl,imx6q-usdhc";
 				reg = <0x0219c000 0x4000>;
 				interrupts = <0 25 0x04>;
+				clocks = <&clks 166>, <&clks 166>, <&clks 166>;
+				clock-names = "ipg", "ahb", "per";
 				status = "disabled";
 			};
 
@@ -707,6 +880,7 @@
 				compatible = "fsl,imx6q-i2c", "fsl,imx1-i2c";
 				reg = <0x021a0000 0x4000>;
 				interrupts = <0 36 0x04>;
+				clocks = <&clks 125>;
 				status = "disabled";
 			};
 
@@ -716,6 +890,7 @@
 				compatible = "fsl,imx6q-i2c", "fsl,imx1-i2c";
 				reg = <0x021a4000 0x4000>;
 				interrupts = <0 37 0x04>;
+				clocks = <&clks 126>;
 				status = "disabled";
 			};
 
@@ -725,6 +900,7 @@
 				compatible = "fsl,imx6q-i2c", "fsl,imx1-i2c";
 				reg = <0x021a8000 0x4000>;
 				interrupts = <0 38 0x04>;
+				clocks = <&clks 127>;
 				status = "disabled";
 			};
 
@@ -788,6 +964,8 @@
 				compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
 				reg = <0x021e8000 0x4000>;
 				interrupts = <0 27 0x04>;
+				clocks = <&clks 160>, <&clks 161>;
+				clock-names = "ipg", "per";
 				status = "disabled";
 			};
 
@@ -795,6 +973,8 @@
 				compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
 				reg = <0x021ec000 0x4000>;
 				interrupts = <0 28 0x04>;
+				clocks = <&clks 160>, <&clks 161>;
+				clock-names = "ipg", "per";
 				status = "disabled";
 			};
 
@@ -802,6 +982,8 @@
 				compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
 				reg = <0x021f0000 0x4000>;
 				interrupts = <0 29 0x04>;
+				clocks = <&clks 160>, <&clks 161>;
+				clock-names = "ipg", "per";
 				status = "disabled";
 			};
 
@@ -809,6 +991,8 @@
 				compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
 				reg = <0x021f4000 0x4000>;
 				interrupts = <0 30 0x04>;
+				clocks = <&clks 160>, <&clks 161>;
+				clock-names = "ipg", "per";
 				status = "disabled";
 			};
 		};

arch/arm/boot/dts/mmp2.dtsi

@@ -26,6 +26,11 @@
 		interrupt-parent = <&intc>;
 		ranges;
 
+		L2: l2-cache {
+			compatible = "marvell,tauros2-cache";
+			marvell,tauros2-cache-features = <0x3>;
+		};
+
 		axi@d4200000 {	/* AXI */
 			compatible = "mrvl,axi-bus", "simple-bus";
 			#address-cells = <1>;

arch/arm/boot/dts/msm8660-surf.dts

@@ -7,7 +7,7 @@
 	compatible = "qcom,msm8660-surf", "qcom,msm8660";
 	interrupt-parent = <&intc>;
 
-	intc: interrupt-controller@02080000 {
+	intc: interrupt-controller@2080000 {
 		compatible = "qcom,msm-8660-qgic";
 		interrupt-controller;
 		#interrupt-cells = <3>;
@@ -15,6 +15,23 @@
 		      < 0x02081000 0x1000 >;
 	};
 
+	timer@2000004 {
+		compatible = "qcom,msm-gpt", "qcom,msm-timer";
+		interrupts = <1 1 0x301>;
+		reg = <0x02000004 0x10>;
+		clock-frequency = <32768>;
+		cpu-offset = <0x40000>;
+	};
+
+	timer@2000024 {
+		compatible = "qcom,msm-dgt", "qcom,msm-timer";
+		interrupts = <1 0 0x301>;
+		reg = <0x02000024 0x10>,
+		      <0x02000034 0x4>;
+		clock-frequency = <6750000>;
+		cpu-offset = <0x40000>;
+	};
+
 	serial@19c400000 {
 		compatible = "qcom,msm-hsuart", "qcom,msm-uart";
 		reg = <0x19c40000 0x1000>,

arch/arm/boot/dts/msm8960-cdp.dts

+/dts-v1/;
+
+/include/ "skeleton.dtsi"
+
+/ {
+	model = "Qualcomm MSM8960 CDP";
+	compatible = "qcom,msm8960-cdp", "qcom,msm8960";
+	interrupt-parent = <&intc>;
+
+	intc: interrupt-controller@2000000 {
+		compatible = "qcom,msm-qgic2";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = < 0x02000000 0x1000 >,
+		      < 0x02002000 0x1000 >;
+	};
+
+	timer@200a004 {
+		compatible = "qcom,msm-gpt", "qcom,msm-timer";
+		interrupts = <1 2 0x301>;
+		reg = <0x0200a004 0x10>;
+		clock-frequency = <32768>;
+		cpu-offset = <0x80000>;
+	};
+
+	timer@200a024 {
+		compatible = "qcom,msm-dgt", "qcom,msm-timer";
+		interrupts = <1 1 0x301>;
+		reg = <0x0200a024 0x10>,
+		      <0x0200a034 0x4>;
+		clock-frequency = <6750000>;
+		cpu-offset = <0x80000>;
+	};
+
+	serial@19c400000 {
+		compatible = "qcom,msm-hsuart", "qcom,msm-uart";
+		reg = <0x16440000 0x1000>,
+		      <0x16400000 0x1000>;
+		interrupts = <0 154 0x0>;
+	};
+};

arch/arm/boot/dts/omap2420-h4.dts

@@ -7,7 +7,7 @@
  */
 /dts-v1/;
 
-/include/ "omap2.dtsi"
+/include/ "omap2420.dtsi"
 
 / {
 	model = "TI OMAP2420 H4 board";

arch/arm/boot/dts/omap2420.dtsi

+/*
+ * Device Tree Source for OMAP2420 SoC
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/include/ "omap2.dtsi"
+
+/ {
+	compatible = "ti,omap2420", "ti,omap2";
+
+	ocp {
+		omap2420_pmx: pinmux@48000030 {
+			compatible = "ti,omap2420-padconf", "pinctrl-single";
+			reg = <0x48000030 0x0113>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-single,register-width = <8>;
+			pinctrl-single,function-mask = <0x3f>;
+		};
+
+		mcbsp1: mcbsp@48074000 {
+			compatible = "ti,omap2420-mcbsp";
+			reg = <0x48074000 0xff>;
+			reg-names = "mpu";
+			interrupts = <59>, /* TX interrupt */
+				     <60>; /* RX interrupt */
+			interrupt-names = "tx", "rx";
+			interrupt-parent = <&intc>;
+			ti,hwmods = "mcbsp1";
+		};
+
+		mcbsp2: mcbsp@48076000 {
+			compatible = "ti,omap2420-mcbsp";
+			reg = <0x48076000 0xff>;
+			reg-names = "mpu";
+			interrupts = <62>, /* TX interrupt */
+				     <63>; /* RX interrupt */
+			interrupt-names = "tx", "rx";
+			interrupt-parent = <&intc>;
+			ti,hwmods = "mcbsp2";
+		};
+	};
+};

arch/arm/boot/dts/omap2430.dtsi

+/*
+ * Device Tree Source for OMAP243x SoC
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/include/ "omap2.dtsi"
+
+/ {
+	compatible = "ti,omap2430", "ti,omap2";
+
+	ocp {
+		omap2430_pmx: pinmux@49002030 {
+			compatible = "ti,omap2430-padconf", "pinctrl-single";
+			reg = <0x49002030 0x0154>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-single,register-width = <8>;
+			pinctrl-single,function-mask = <0x3f>;
+		};
+
+		mcbsp1: mcbsp@48074000 {
+			compatible = "ti,omap2430-mcbsp";
+			reg = <0x48074000 0xff>;
+			reg-names = "mpu";
+			interrupts = <64>, /* OCP compliant interrupt */
+				     <59>, /* TX interrupt */
+				     <60>, /* RX interrupt */
+				     <61>; /* RX overflow interrupt */
+			interrupt-names = "common", "tx", "rx", "rx_overflow";
+			interrupt-parent = <&intc>;
+			ti,buffer-size = <128>;
+			ti,hwmods = "mcbsp1";
+		};
+
+		mcbsp2: mcbsp@48076000 {
+			compatible = "ti,omap2430-mcbsp";
+			reg = <0x48076000 0xff>;
+			reg-names = "mpu";
+			interrupts = <16>, /* OCP compliant interrupt */
+				     <62>, /* TX interrupt */
+				     <63>; /* RX interrupt */
+			interrupt-names = "common", "tx", "rx";
+			interrupt-parent = <&intc>;
+			ti,buffer-size = <128>;
+			ti,hwmods = "mcbsp2";
+		};
+
+		mcbsp3: mcbsp@4808c000 {
+			compatible = "ti,omap2430-mcbsp";
+			reg = <0x4808c000 0xff>;
+			reg-names = "mpu";
+			interrupts = <17>, /* OCP compliant interrupt */
+				     <89>, /* TX interrupt */
+				     <90>; /* RX interrupt */
+			interrupt-names = "common", "tx", "rx";
+			interrupt-parent = <&intc>;
+			ti,buffer-size = <128>;
+			ti,hwmods = "mcbsp3";
+		};
+
+		mcbsp4: mcbsp@4808e000 {
+			compatible = "ti,omap2430-mcbsp";
+			reg = <0x4808e000 0xff>;
+			reg-names = "mpu";
+			interrupts = <18>, /* OCP compliant interrupt */
+				     <54>, /* TX interrupt */
+				     <55>; /* RX interrupt */
+			interrupt-names = "common", "tx", "rx";
+			interrupt-parent = <&intc>;
+			ti,buffer-size = <128>;
+			ti,hwmods = "mcbsp4";
+		};
+
+		mcbsp5: mcbsp@48096000 {
+			compatible = "ti,omap2430-mcbsp";
+			reg = <0x48096000 0xff>;
+			reg-names = "mpu";
+			interrupts = <19>, /* OCP compliant interrupt */
+				     <81>, /* TX interrupt */
+				     <82>; /* RX interrupt */
+			interrupt-names = "common", "tx", "rx";
+			interrupt-parent = <&intc>;
+			ti,buffer-size = <128>;
+			ti,hwmods = "mcbsp5";
+		};
+	};
+};

arch/arm/boot/dts/omap3-beagle.dts → arch/arm/boot/dts/omap3-beagle-xm.dts

@@ -7,16 +7,44 @@
  */
 /dts-v1/;
 
-/include/ "omap3.dtsi"
+/include/ "omap36xx.dtsi"
 
 / {
-	model = "TI OMAP3 BeagleBoard";
-	compatible = "ti,omap3-beagle", "ti,omap3";
+	model = "TI OMAP3 BeagleBoard xM";
+	compatible = "ti,omap3-beagle-xm, ti,omap3-beagle", "ti,omap3";
 
 	memory {
 		device_type = "memory";
 		reg = <0x80000000 0x20000000>; /* 512 MB */
 	};
+
+	leds {
+		compatible = "gpio-leds";
+		pmu_stat {
+			label = "beagleboard::pmu_stat";
+			gpios = <&twl_gpio 19 0>; /* LEDB */
+		};
+
+		heartbeat {
+			label = "beagleboard::usr0";
+			gpios = <&gpio5 22 0>; /* 150 -> D6 LED */
+			linux,default-trigger = "heartbeat";
+		};
+
+		mmc {
+			label = "beagleboard::usr1";
+			gpios = <&gpio5 21 0>; /* 149 -> D7 LED */
+			linux,default-trigger = "mmc0";
+		};
+	};
+
+	sound {
+		compatible = "ti,omap-twl4030";
+		ti,model = "omap3beagle";
+
+		ti,mcbsp = <&mcbsp2>;
+		ti,codec = <&twl_audio>;
+	};
 };
 
 &i2c1 {
@@ -27,11 +55,17 @@
 		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
 		interrupt-parent = <&intc>;
 
-		vsim: regulator@10 {
+		vsim: regulator-vsim {
 			compatible = "ti,twl4030-vsim";
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <3000000>;
 		};
+
+		twl_audio: audio {
+			compatible = "ti,twl4030-audio";
+			codec {
+			};
+		};
 	};
 };
 
@@ -67,3 +101,15 @@
 &mmc3 {
 	status = "disabled";
 };
+
+&twl_gpio {
+	ti,use-leds;
+	/* pullups: BIT(1) */
+	ti,pullups = <0x000002>;
+	/*
+	 * pulldowns:
+	 * BIT(2), BIT(6), BIT(7), BIT(8), BIT(13)
+	 * BIT(15), BIT(16), BIT(17)
+	 */
+	ti,pulldowns = <0x03a1c4>;
+};

arch/arm/boot/dts/omap3-evm.dts

@@ -17,6 +17,15 @@
 		device_type = "memory";
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
+
+	leds {
+		compatible = "gpio-leds";
+		ledb {
+			label = "omap3evm::ledb";
+			gpios = <&twl_gpio 19 0>; /* LEDB */
+			linux,default-trigger = "default-on";
+		};
+	};
 };
 
 &i2c1 {
@@ -46,3 +55,7 @@
 		reg = <0x5c>;
 	};
 };
+
+&twl_gpio {
+	ti,use-leds;
+};

arch/arm/boot/dts/omap3-overo.dtsi

+/*
+ * Copyright (C) 2012 Florian Vaussard, EPFL Mobots group
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * The Gumstix Overo must be combined with an expansion board.
+ */
+/dts-v1/;
+
+/include/ "omap3.dtsi"
+
+/ {
+	leds {
+		compatible = "gpio-leds";
+		overo {
+			label = "overo:blue:COM";
+			gpios = <&twl_gpio 19 0>;
+			linux,default-trigger = "mmc0";
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+	};
+};
+
+/include/ "twl4030.dtsi"
+
+/* i2c2 pins are used for gpio */
+&i2c2 {
+	status = "disabled";
+};
+
+/* on board microSD slot */
+&mmc1 {
+	vmmc-supply = <&vmmc1>;
+	bus-width = <4>;
+};
+
+/* optional on board WiFi */
+&mmc2 {
+	bus-width = <4>;
+};
+
+&twl_gpio {
+	ti,use-leds;
+};

arch/arm/boot/dts/omap3-tobi.dts

+/*
+ * Copyright (C) 2012 Florian Vaussard, EPFL Mobots group
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Tobi expansion board is manufactured by Gumstix Inc.
+ */
+
+/include/ "omap3-overo.dtsi"
+
+/ {
+	model = "TI OMAP3 Gumstix Overo on Tobi";
+	compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3";
+
+	leds {
+		compatible = "gpio-leds";
+		heartbeat {
+			label = "overo:red:gpio21";
+			gpios = <&gpio1 21 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+};
+
+&mmc3 {
+	status = "disabled";
+};

arch/arm/boot/dts/omap3.dtsi

@@ -17,7 +17,6 @@
 		serial0 = &uart1;
 		serial1 = &uart2;
 		serial2 = &uart3;
-		serial3 = &uart4;
 	};
 
 	cpus {
@@ -69,6 +68,24 @@
 			reg = <0x48200000 0x1000>;
 		};
 
+		omap3_pmx_core: pinmux@48002030 {
+			compatible = "ti,omap3-padconf", "pinctrl-single";
+			reg = <0x48002030 0x05cc>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-single,register-width = <16>;
+			pinctrl-single,function-mask = <0x7fff>;
+		};
+
+		omap3_pmx_wkup: pinmux@0x48002a58 {
+			compatible = "ti,omap3-padconf", "pinctrl-single";
+			reg = <0x48002a58 0x5c>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-single,register-width = <16>;
+			pinctrl-single,function-mask = <0x7fff>;
+		};
+
 		gpio1: gpio@48310000 {
 			compatible = "ti,omap3-gpio";
 			ti,hwmods = "gpio1";
@@ -141,12 +158,6 @@
 			clock-frequency = <48000000>;
 		};
 
-		uart4: serial@49042000 {
-			compatible = "ti,omap3-uart";
-			ti,hwmods = "uart4";
-			clock-frequency = <48000000>;
-		};
-
 		i2c1: i2c@48070000 {
 			compatible = "ti,omap3-i2c";
 			#address-cells = <1>;
@@ -220,5 +231,74 @@
 			compatible = "ti,omap3-wdt";
 			ti,hwmods = "wd_timer2";
 		};
+
+		mcbsp1: mcbsp@48074000 {
+			compatible = "ti,omap3-mcbsp";
+			reg = <0x48074000 0xff>;
+			reg-names = "mpu";
+			interrupts = <16>, /* OCP compliant interrupt */
+				     <59>, /* TX interrupt */
+				     <60>; /* RX interrupt */
+			interrupt-names = "common", "tx", "rx";
+			interrupt-parent = <&intc>;
+			ti,buffer-size = <128>;
+			ti,hwmods = "mcbsp1";
+		};
+
+		mcbsp2: mcbsp@49022000 {
+			compatible = "ti,omap3-mcbsp";
+			reg = <0x49022000 0xff>,
+			      <0x49028000 0xff>;
+			reg-names = "mpu", "sidetone";
+			interrupts = <17>, /* OCP compliant interrupt */
+				     <62>, /* TX interrupt */
+				     <63>, /* RX interrupt */
+				     <4>;  /* Sidetone */
+			interrupt-names = "common", "tx", "rx", "sidetone";
+			interrupt-parent = <&intc>;
+			ti,buffer-size = <1280>;
+			ti,hwmods = "mcbsp2";
+		};
+
+		mcbsp3: mcbsp@49024000 {
+			compatible = "ti,omap3-mcbsp";
+			reg = <0x49024000 0xff>,
+			      <0x4902a000 0xff>;
+			reg-names = "mpu", "sidetone";
+			interrupts = <22>, /* OCP compliant interrupt */
+				     <89>, /* TX interrupt */
+				     <90>, /* RX interrupt */
+				     <5>;  /* Sidetone */
+			interrupt-names = "common", "tx", "rx", "sidetone";
+			interrupt-parent = <&intc>;
+			ti,buffer-size = <128>;
+			ti,hwmods = "mcbsp3";
+		};
+
+		mcbsp4: mcbsp@49026000 {
+			compatible = "ti,omap3-mcbsp";
+			reg = <0x49026000 0xff>;
+			reg-names = "mpu";
+			interrupts = <23>, /* OCP compliant interrupt */
+				     <54>, /* TX interrupt */
+				     <55>; /* RX interrupt */
+			interrupt-names = "common", "tx", "rx";
+			interrupt-parent = <&intc>;
+			ti,buffer-size = <128>;
+			ti,hwmods = "mcbsp4";
+		};
+
+		mcbsp5: mcbsp@48096000 {
+			compatible = "ti,omap3-mcbsp";
+			reg = <0x48096000 0xff>;
+			reg-names = "mpu";
+			interrupts = <27>, /* OCP compliant interrupt */
+				     <81>, /* TX interrupt */
+				     <82>; /* RX interrupt */
+			interrupt-names = "common", "tx", "rx";
+			interrupt-parent = <&intc>;
+			ti,buffer-size = <128>;
+			ti,hwmods = "mcbsp5";
+		};
 	};
 };

arch/arm/boot/dts/omap36xx.dtsi

+/*
+ * Device Tree Source for OMAP3 SoC
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/include/ "omap3.dtsi"
+
+/ {
+	aliases {
+		serial3 = &uart4;
+	};
+
+	ocp {
+		uart4: serial@49042000 {
+			compatible = "ti,omap3-uart";
+			ti,hwmods = "uart4";
+			clock-frequency = <48000000>;
+		};
+	};
+};

arch/arm/boot/dts/omap4-panda.dts

@@ -8,6 +8,7 @@
 /dts-v1/;
 
 /include/ "omap4.dtsi"
+/include/ "elpida_ecb240abacn.dtsi"
 
 / {
 	model = "TI OMAP4 PandaBoard";
@@ -126,3 +127,13 @@
 	ti,non-removable;
 	bus-width = <4>;
 };
+
+&emif1 {
+	cs1-used;
+	device-handle = <&elpida_ECB240ABACN>;
+};
+
+&emif2 {
+	cs1-used;
+	device-handle = <&elpida_ECB240ABACN>;
+};

arch/arm/boot/dts/omap4-sdp.dts

@@ -8,6 +8,7 @@
 /dts-v1/;
 
 /include/ "omap4.dtsi"
+/include/ "elpida_ecb240abacn.dtsi"
 
 / {
 	model = "TI OMAP4 SDP board";
@@ -18,7 +19,7 @@
 		reg = <0x80000000 0x40000000>; /* 1 GB */
 	};
 
-	vdd_eth: fixedregulator@0 {
+	vdd_eth: fixedregulator-vdd-eth {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_ETH";
 		regulator-min-microvolt = <3300000>;
@@ -28,7 +29,7 @@
 		regulator-boot-on;
 	};
 
-	vbat: fixedregulator@2 {
+	vbat: fixedregulator-vbat {
 		compatible = "regulator-fixed";
 		regulator-name = "VBAT";
 		regulator-min-microvolt = <3750000>;
@@ -115,6 +116,33 @@
 	};
 };
 
+&omap4_pmx_core {
+	uart2_pins: pinmux_uart2_pins {
+		pinctrl-single,pins = <
+			0xd8 0x118	/* uart2_cts.uart2_cts INPUT_PULLUP | MODE0 */
+			0xda 0		/* uart2_rts.uart2_rts OUTPUT | MODE0 */
+			0xdc 0x118	/* uart2_rx.uart2_rx INPUT_PULLUP | MODE0 */
+			0xde 0		/* uart2_tx.uart2_tx OUTPUT | MODE0 */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			0x100 0x118	/* uart3_cts_rctx.uart3_cts_rctx INPUT_PULLUP | MODE0 */
+			0x102 0		/* uart3_rts_sd.uart3_rts_sd OUTPUT | MODE0 */
+			0x104 0x100	/* uart3_rx_irrx.uart3_rx_irrx INPUT | MODE0 */
+			0x106 0		/* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
+		>;
+	};
+
+	uart4_pins: pinmux_uart4_pins {
+		pinctrl-single,pins = <
+			0x11c 0x100	/* uart4_rx.uart4_rx INPUT | MODE0 */
+			0x11e 0		/* uart4_tx.uart4_tx OUTPUT | MODE0 */
+		>;
+	};
+};
+
 &i2c1 {
 	clock-frequency = <400000>;
 
@@ -226,3 +254,98 @@
 	bus-width = <4>;
 	ti,non-removable;
 };
+
+&emif1 {
+	cs1-used;
+	device-handle = <&elpida_ECB240ABACN>;
+};
+
+&emif2 {
+	cs1-used;
+	device-handle = <&elpida_ECB240ABACN>;
+};
+
+&keypad {
+	keypad,num-rows = <8>;
+	keypad,num-columns = <8>;
+	linux,keymap = <0x00000012	/* KEY_E */
+			0x00010013	/* KEY_R */
+			0x00020014	/* KEY_T */
+			0x00030066	/* KEY_HOME */
+			0x0004003f	/* KEY_F5 */
+			0x000500f0	/* KEY_UNKNOWN */
+			0x00060017	/* KEY_I */
+			0x0007002a	/* KEY_LEFTSHIFT */
+			0x01000020	/* KEY_D*/
+			0x01010021	/* KEY_F */
+			0x01020022	/* KEY_G */
+			0x010300e7	/* KEY_SEND */
+			0x01040040	/* KEY_F6 */
+			0x010500f0	/* KEY_UNKNOWN */
+			0x01060025	/* KEY_K */
+			0x0107001c	/* KEY_ENTER */
+			0x0200002d	/* KEY_X */
+			0x0201002e	/* KEY_C */
+			0x0202002f	/* KEY_V */
+			0x0203006b	/* KEY_END */
+			0x02040041	/* KEY_F7 */
+			0x020500f0	/* KEY_UNKNOWN */
+			0x02060034	/* KEY_DOT */
+			0x0207003a	/* KEY_CAPSLOCK */
+			0x0300002c	/* KEY_Z */
+			0x0301004e	/* KEY_KPLUS */
+			0x03020030	/* KEY_B */
+			0x0303003b	/* KEY_F1 */
+			0x03040042	/* KEY_F8 */
+			0x030500f0	/* KEY_UNKNOWN */
+			0x03060018	/* KEY_O */
+			0x03070039	/* KEY_SPACE */
+			0x04000011	/* KEY_W */
+			0x04010015	/* KEY_Y */
+			0x04020016	/* KEY_U */
+			0x0403003c	/* KEY_F2 */
+			0x04040073	/* KEY_VOLUMEUP */
+			0x040500f0	/* KEY_UNKNOWN */
+			0x04060026	/* KEY_L */
+			0x04070069	/* KEY_LEFT */
+			0x0500001f	/* KEY_S */
+			0x05010023	/* KEY_H */
+			0x05020024	/* KEY_J */
+			0x0503003d	/* KEY_F3 */
+			0x05040043	/* KEY_F9 */
+			0x05050072	/* KEY_VOLUMEDOWN */
+			0x05060032	/* KEY_M */
+			0x0507006a	/* KEY_RIGHT */
+			0x06000010	/* KEY_Q */
+			0x0601001e	/* KEY_A */
+			0x06020031	/* KEY_N */
+			0x0603009e	/* KEY_BACK */
+			0x0604000e	/* KEY_BACKSPACE */
+			0x060500f0	/* KEY_UNKNOWN */
+			0x06060019	/* KEY_P */
+			0x06070067	/* KEY_UP */
+			0x07000094	/* KEY_PROG1 */
+			0x07010095	/* KEY_PROG2 */
+			0x070200ca	/* KEY_PROG3 */
+			0x070300cb	/* KEY_PROG4 */
+			0x0704003e	/* KEY_F4 */
+			0x070500f0	/* KEY_UNKNOWN */
+			0x07060160	/* KEY_OK */
+			0x0707006c>;	/* KEY_DOWN */
+	linux,input-no-autorepeat;
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins>;
+};

arch/arm/boot/dts/omap4.dtsi

@@ -30,12 +30,35 @@
 	cpus {
 		cpu@0 {
 			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
 		};
 		cpu@1 {
 			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
 		};
 	};
 
+	gic: interrupt-controller@48241000 {
+		compatible = "arm,cortex-a9-gic";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0x48241000 0x1000>,
+		      <0x48240100 0x0100>;
+	};
+
+	L2: l2-cache-controller@48242000 {
+		compatible = "arm,pl310-cache";
+		reg = <0x48242000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+	};
+
+	local-timer@0x48240600 {
+		compatible = "arm,cortex-a9-twd-timer";
+		reg = <0x48240600 0x20>;
+		interrupts = <1 13 0x304>;
+	};
+
 	/*
 	 * The soc node represents the soc top level view. It is uses for IPs
 	 * that are not memory mapped in the MPU view or for the MPU itself.
@@ -61,30 +84,6 @@
 	/*
 	 * XXX: Use a flat representation of the OMAP4 interconnect.
 	 * The real OMAP interconnect network is quite complex.
-	 *
-	 * MPU -+-- MPU_PRIVATE - GIC, L2
-	 *      |
-	 *      +----------------+----------+
-	 *      |                |          |
-	 *      +            +- EMIF - DDR  |
-	 *      |            |              |
-	 *      |            +     +--------+
-	 *      |            |     |
-	 *      |            +- L4_ABE - AESS, MCBSP, TIMERs...
-	 *      |            |
-	 *      +- L3_MAIN --+- L4_CORE - IPs...
-	 *                   |
-	 *                   +- L4_PER - IPs...
-	 *                   |
-	 *                   +- L4_CFG -+- L4_WKUP - IPs...
-	 *                   |          |
-	 *                   |          +- IPs...
-	 *                   +- IPU ----+
-	 *                   |          |
-	 *                   +- DSP ----+
-	 *                   |          |
-	 *                   +- DSS ----+
-	 *
 	 * Since that will not bring real advantage to represent that in DT for
 	 * the moment, just use a fake OCP bus entry to represent the whole bus
 	 * hierarchy.
@@ -96,16 +95,27 @@
 		ranges;
 		ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
 
-		gic: interrupt-controller@48241000 {
-			compatible = "arm,cortex-a9-gic";
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			reg = <0x48241000 0x1000>,
-			      <0x48240100 0x0100>;
+		omap4_pmx_core: pinmux@4a100040 {
+			compatible = "ti,omap4-padconf", "pinctrl-single";
+			reg = <0x4a100040 0x0196>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-single,register-width = <16>;
+			pinctrl-single,function-mask = <0x7fff>;
+		};
+		omap4_pmx_wkup: pinmux@4a31e040 {
+			compatible = "ti,omap4-padconf", "pinctrl-single";
+			reg = <0x4a31e040 0x0038>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-single,register-width = <16>;
+			pinctrl-single,function-mask = <0x7fff>;
 		};
 
 		gpio1: gpio@4a310000 {
 			compatible = "ti,omap4-gpio";
+			reg = <0x4a310000 0x200>;
+			interrupts = <0 29 0x4>;
 			ti,hwmods = "gpio1";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -115,6 +125,8 @@
 
 		gpio2: gpio@48055000 {
 			compatible = "ti,omap4-gpio";
+			reg = <0x48055000 0x200>;
+			interrupts = <0 30 0x4>;
 			ti,hwmods = "gpio2";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -124,6 +136,8 @@
 
 		gpio3: gpio@48057000 {
 			compatible = "ti,omap4-gpio";
+			reg = <0x48057000 0x200>;
+			interrupts = <0 31 0x4>;
 			ti,hwmods = "gpio3";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -133,6 +147,8 @@
 
 		gpio4: gpio@48059000 {
 			compatible = "ti,omap4-gpio";
+			reg = <0x48059000 0x200>;
+			interrupts = <0 32 0x4>;
 			ti,hwmods = "gpio4";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -142,6 +158,8 @@
 
 		gpio5: gpio@4805b000 {
 			compatible = "ti,omap4-gpio";
+			reg = <0x4805b000 0x200>;
+			interrupts = <0 33 0x4>;
 			ti,hwmods = "gpio5";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -151,6 +169,8 @@
 
 		gpio6: gpio@4805d000 {
 			compatible = "ti,omap4-gpio";
+			reg = <0x4805d000 0x200>;
+			interrupts = <0 34 0x4>;
 			ti,hwmods = "gpio6";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -160,30 +180,40 @@
 
 		uart1: serial@4806a000 {
 			compatible = "ti,omap4-uart";
+			reg = <0x4806a000 0x100>;
+			interrupts = <0 72 0x4>;
 			ti,hwmods = "uart1";
 			clock-frequency = <48000000>;
 		};
 
 		uart2: serial@4806c000 {
 			compatible = "ti,omap4-uart";
+			reg = <0x4806c000 0x100>;
+			interrupts = <0 73 0x4>;
 			ti,hwmods = "uart2";
 			clock-frequency = <48000000>;
 		};
 
 		uart3: serial@48020000 {
 			compatible = "ti,omap4-uart";
+			reg = <0x48020000 0x100>;
+			interrupts = <0 74 0x4>;
 			ti,hwmods = "uart3";
 			clock-frequency = <48000000>;
 		};
 
 		uart4: serial@4806e000 {
 			compatible = "ti,omap4-uart";
+			reg = <0x4806e000 0x100>;
+			interrupts = <0 70 0x4>;
 			ti,hwmods = "uart4";
 			clock-frequency = <48000000>;
 		};
 
 		i2c1: i2c@48070000 {
 			compatible = "ti,omap4-i2c";
+			reg = <0x48070000 0x100>;
+			interrupts = <0 56 0x4>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c1";
@@ -191,6 +221,8 @@
 
 		i2c2: i2c@48072000 {
 			compatible = "ti,omap4-i2c";
+			reg = <0x48072000 0x100>;
+			interrupts = <0 57 0x4>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c2";
@@ -198,6 +230,8 @@
 
 		i2c3: i2c@48060000 {
 			compatible = "ti,omap4-i2c";
+			reg = <0x48060000 0x100>;
+			interrupts = <0 61 0x4>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c3";
@@ -205,6 +239,8 @@
 
 		i2c4: i2c@48350000 {
 			compatible = "ti,omap4-i2c";
+			reg = <0x48350000 0x100>;
+			interrupts = <0 62 0x4>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c4";
@@ -212,6 +248,8 @@
 
 		mcspi1: spi@48098000 {
 			compatible = "ti,omap4-mcspi";
+			reg = <0x48098000 0x200>;
+			interrupts = <0 65 0x4>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "mcspi1";
@@ -220,6 +258,8 @@
 
 		mcspi2: spi@4809a000 {
 			compatible = "ti,omap4-mcspi";
+			reg = <0x4809a000 0x200>;
+			interrupts = <0 66 0x4>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "mcspi2";
@@ -228,6 +268,8 @@
 
 		mcspi3: spi@480b8000 {
 			compatible = "ti,omap4-mcspi";
+			reg = <0x480b8000 0x200>;
+			interrupts = <0 91 0x4>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "mcspi3";
@@ -236,6 +278,8 @@
 
 		mcspi4: spi@480ba000 {
 			compatible = "ti,omap4-mcspi";
+			reg = <0x480ba000 0x200>;
+			interrupts = <0 48 0x4>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "mcspi4";
@@ -244,6 +288,8 @@
 
 		mmc1: mmc@4809c000 {
 			compatible = "ti,omap4-hsmmc";
+			reg = <0x4809c000 0x400>;
+			interrupts = <0 83 0x4>;
 			ti,hwmods = "mmc1";
 			ti,dual-volt;
 			ti,needs-special-reset;
@@ -251,30 +297,40 @@
 
 		mmc2: mmc@480b4000 {
 			compatible = "ti,omap4-hsmmc";
+			reg = <0x480b4000 0x400>;
+			interrupts = <0 86 0x4>;
 			ti,hwmods = "mmc2";
 			ti,needs-special-reset;
 		};
 
 		mmc3: mmc@480ad000 {
 			compatible = "ti,omap4-hsmmc";
+			reg = <0x480ad000 0x400>;
+			interrupts = <0 94 0x4>;
 			ti,hwmods = "mmc3";
 			ti,needs-special-reset;
 		};
 
 		mmc4: mmc@480d1000 {
 			compatible = "ti,omap4-hsmmc";
+			reg = <0x480d1000 0x400>;
+			interrupts = <0 96 0x4>;
 			ti,hwmods = "mmc4";
 			ti,needs-special-reset;
 		};
 
 		mmc5: mmc@480d5000 {
 			compatible = "ti,omap4-hsmmc";
+			reg = <0x480d5000 0x400>;
+			interrupts = <0 59 0x4>;
 			ti,hwmods = "mmc5";
 			ti,needs-special-reset;
 		};
 
 		wdt2: wdt@4a314000 {
 			compatible = "ti,omap4-wdt", "ti,omap3-wdt";
+			reg = <0x4a314000 0x80>;
+			interrupts = <0 80 0x4>;
 			ti,hwmods = "wd_timer2";
 		};
 
@@ -282,6 +338,7 @@
 			compatible = "ti,omap4-mcpdm";
 			reg = <0x40132000 0x7f>, /* MPU private access */
 			      <0x49032000 0x7f>; /* L3 Interconnect */
+			reg-names = "mpu", "dma";
 			interrupts = <0 112 0x4>;
 			interrupt-parent = <&gic>;
 			ti,hwmods = "mcpdm";
@@ -291,9 +348,87 @@
 			compatible = "ti,omap4-dmic";
 			reg = <0x4012e000 0x7f>, /* MPU private access */
 			      <0x4902e000 0x7f>; /* L3 Interconnect */
+			reg-names = "mpu", "dma";
 			interrupts = <0 114 0x4>;
 			interrupt-parent = <&gic>;
 			ti,hwmods = "dmic";
 		};
+
+		mcbsp1: mcbsp@40122000 {
+			compatible = "ti,omap4-mcbsp";
+			reg = <0x40122000 0xff>, /* MPU private access */
+			      <0x49022000 0xff>; /* L3 Interconnect */
+			reg-names = "mpu", "dma";
+			interrupts = <0 17 0x4>;
+			interrupt-names = "common";
+			interrupt-parent = <&gic>;
+			ti,buffer-size = <128>;
+			ti,hwmods = "mcbsp1";
+		};
+
+		mcbsp2: mcbsp@40124000 {
+			compatible = "ti,omap4-mcbsp";
+			reg = <0x40124000 0xff>, /* MPU private access */
+			      <0x49024000 0xff>; /* L3 Interconnect */
+			reg-names = "mpu", "dma";
+			interrupts = <0 22 0x4>;
+			interrupt-names = "common";
+			interrupt-parent = <&gic>;
+			ti,buffer-size = <128>;
+			ti,hwmods = "mcbsp2";
+		};
+
+		mcbsp3: mcbsp@40126000 {
+			compatible = "ti,omap4-mcbsp";
+			reg = <0x40126000 0xff>, /* MPU private access */
+			      <0x49026000 0xff>; /* L3 Interconnect */
+			reg-names = "mpu", "dma";
+			interrupts = <0 23 0x4>;
+			interrupt-names = "common";
+			interrupt-parent = <&gic>;
+			ti,buffer-size = <128>;
+			ti,hwmods = "mcbsp3";
+		};
+
+		mcbsp4: mcbsp@48096000 {
+			compatible = "ti,omap4-mcbsp";
+			reg = <0x48096000 0xff>; /* L4 Interconnect */
+			reg-names = "mpu";
+			interrupts = <0 16 0x4>;
+			interrupt-names = "common";
+			interrupt-parent = <&gic>;
+			ti,buffer-size = <128>;
+			ti,hwmods = "mcbsp4";
+		};
+
+		keypad: keypad@4a31c000 {
+			compatible = "ti,omap4-keypad";
+			reg = <0x4a31c000 0x80>;
+			interrupts = <0 120 0x4>;
+			reg-names = "mpu";
+			ti,hwmods = "kbd";
+		};
+
+		emif1: emif@4c000000 {
+			compatible = "ti,emif-4d";
+			reg = <0x4c000000 0x100>;
+			interrupts = <0 110 0x4>;
+			ti,hwmods = "emif1";
+			phy-type = <1>;
+			hw-caps-read-idle-ctrl;
+			hw-caps-ll-interface;
+			hw-caps-temp-alert;
+		};
+
+		emif2: emif@4d000000 {
+			compatible = "ti,emif-4d";
+			reg = <0x4d000000 0x100>;
+			interrupts = <0 111 0x4>;
+			ti,hwmods = "emif2";
+			phy-type = <1>;
+			hw-caps-read-idle-ctrl;
+			hw-caps-ll-interface;
+			hw-caps-temp-alert;
+		};
 	};
 };

arch/arm/boot/dts/omap5-evm.dts

@@ -17,4 +17,68 @@
 		device_type = "memory";
 		reg = <0x80000000 0x40000000>; /* 1 GB */
 	};
+
+	vmmcsd_fixed: fixedregulator-mmcsd {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+	};
+
+};
+
+&mmc1 {
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <4>;
+};
+
+&mmc2 {
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <8>;
+	ti,non-removable;
+};
+
+&mmc3 {
+	bus-width = <4>;
+	ti,non-removable;
+};
+
+&mmc4 {
+	status = "disabled";
+};
+
+&mmc5 {
+	status = "disabled";
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+
+	/* Pressure Sensor */
+	bmp085@77 {
+		compatible = "bosch,bmp085";
+		reg = <0x77>;
+	};
+};
+
+&i2c4 {
+	clock-frequency = <400000>;
+
+	/* Temperature Sensor */
+	tmp102@48{
+		compatible = "ti,tmp102";
+		reg = <0x48>;
+	};
+};
+
+&keypad {
+	keypad,num-rows = <8>;
+	keypad,num-columns = <8>;
+	linux,keymap = <0x02020073	/* VOLUP */
+			0x02030072	/* VOLDOWM */
+			0x020400e7	/* SEND */
+			0x02050066	/* HOME */
+			0x0206006b	/* END */
+			0x020700d9>;	/* SEARCH */
+	linux,input-no-autorepeat;
 };

arch/arm/boot/dts/phy3250.dts

@@ -135,13 +135,11 @@
 			ssp0: ssp@20084000 {
 				#address-cells = <1>;
 				#size-cells = <0>;
-				pl022,num-chipselects = <1>;
+				num-cs = <1>;
 				cs-gpios = <&gpio 3 5 0>;
 
 				eeprom: at25@0 {
-					pl022,hierarchy = <0>;
 					pl022,interface = <0>;
-					pl022,slave-tx-disable = <0>;
 					pl022,com-mode = <0>;
 					pl022,rx-level-trig = <1>;
 					pl022,tx-level-trig = <1>;

arch/arm/boot/dts/prima2-evb.dts

+/*
+ * DTS file for CSR SiRFprimaII Evaluation Board
+ *
+ * Copyright (c) 2012 Cambridge Silicon Radio Limited, a CSR plc group company.
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/dts-v1/;
+
+/include/ "prima2.dtsi"
+
+/ {
+	model = "CSR SiRFprimaII Evaluation Board";
+	compatible = "sirf,prima2", "sirf,prima2-cb";
+
+	memory {
+		reg = <0x00000000 0x20000000>;
+	};
+
+	axi {
+		peri-iobg {
+			uart@b0060000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart1_pins_a>;
+			};
+			spi@b00d0000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi0_pins_a>;
+			};
+			spi@b0170000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi1_pins_a>;
+			};
+		};
+	};
+};