提交 e554840c 编写于 作者: M Moritz König 提交者: Greg Kroah-Hartman

STAGING: COMEDI: Fixed format of comments in plx9080.h

This patch fixes the format of comments in plx9080.h.
Signed-off-by: NMoritz König <moritz.koenig@fau.de>
Signed-off-by: NFabian Lang <fabian.lang@fau.de>
Reviewed-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
上级 2acc980b
/* plx9080.h
/*
* plx9080.h
*
* Copyright (C) 2002,2003 Frank Mori Hess <fmhess@users.sourceforge.net>
*
......@@ -33,8 +34,10 @@ struct plx_dma_desc {
__le32 local_start_addr;
/* transfer_size is in bytes, only first 23 bits of register are used */
__le32 transfer_size;
/* address of next descriptor (quad word aligned), plus some
* additional bits (see PLX_DMA0_DESCRIPTOR_REG) */
/*
* address of next descriptor (quad word aligned), plus some
* additional bits (see PLX_DMA0_DESCRIPTOR_REG)
*/
__le32 next;
};
......@@ -46,23 +49,31 @@ struct plx_dma_desc {
**
**********************************************************************/
#define PLX_LAS0RNG_REG 0x0000 /* L, Local Addr Space 0 Range Register */
#define PLX_LAS1RNG_REG 0x00f0 /* L, Local Addr Space 1 Range Register */
/* L, Local Addr Space 0 Range Register */
#define PLX_LAS0RNG_REG 0x0000
/* L, Local Addr Space 1 Range Register */
#define PLX_LAS1RNG_REG 0x00f0
#define LRNG_IO 0x00000001 /* Map to: 1=I/O, 0=Mem */
#define LRNG_ANY32 0x00000000 /* Locate anywhere in 32 bit */
#define LRNG_LT1MB 0x00000002 /* Locate in 1st meg */
#define LRNG_ANY64 0x00000004 /* Locate anywhere in 64 bit */
#define LRNG_MEM_MASK 0xfffffff0 /* bits that specify range for memory io */
#define LRNG_IO_MASK 0xfffffffa /* bits that specify range for normal io */
#define PLX_LAS0MAP_REG 0x0004 /* L, Local Addr Space 0 Remap Register */
#define PLX_LAS1MAP_REG 0x00f4 /* L, Local Addr Space 1 Remap Register */
/* bits that specify range for memory io */
#define LRNG_MEM_MASK 0xfffffff0
/* bits that specify range for normal io */
#define LRNG_IO_MASK 0xfffffffa
/* L, Local Addr Space 0 Remap Register */
#define PLX_LAS0MAP_REG 0x0004
/* L, Local Addr Space 1 Remap Register */
#define PLX_LAS1MAP_REG 0x00f4
#define LMAP_EN 0x00000001 /* Enable slave decode */
#define LMAP_MEM_MASK 0xfffffff0 /* bits that specify decode for memory io */
#define LMAP_IO_MASK 0xfffffffa /* bits that specify decode bits for normal io */
/* bits that specify decode for memory io */
#define LMAP_MEM_MASK 0xfffffff0
/* bits that specify decode bits for normal io */
#define LMAP_IO_MASK 0xfffffffa
/* Mode/Arbitration Register.
*/
/*
* Mode/Arbitration Register.
*/
#define PLX_MARB_REG 0x8 /* L, Local Arbitration Register */
#define PLX_DMAARB_REG 0xac
enum marb_bits {
......@@ -72,35 +83,45 @@ enum marb_bits {
MARB_LPEN = 0x00020000, /* Pause Timer Enable */
MARB_BREQ = 0x00040000, /* Local Bus BREQ Enable */
MARB_DMA_PRIORITY_MASK = 0x00180000,
MARB_LBDS_GIVE_UP_BUS_MODE = 0x00200000, /* local bus direct slave give up bus mode */
MARB_DS_LLOCK_ENABLE = 0x00400000, /* direct slave LLOCKo# enable */
/* local bus direct slave give up bus mode */
MARB_LBDS_GIVE_UP_BUS_MODE = 0x00200000,
/* direct slave LLOCKo# enable */
MARB_DS_LLOCK_ENABLE = 0x00400000,
MARB_PCI_REQUEST_MODE = 0x00800000,
MARB_PCIv21_MODE = 0x01000000, /* pci specification v2.1 mode */
MARB_PCI_READ_NO_WRITE_MODE = 0x02000000,
MARB_PCI_READ_WITH_WRITE_FLUSH_MODE = 0x04000000,
MARB_GATE_TIMER_WITH_BREQ = 0x08000000, /* gate local bus latency timer with BREQ */
/* gate local bus latency timer with BREQ */
MARB_GATE_TIMER_WITH_BREQ = 0x08000000,
MARB_PCI_READ_NO_FLUSH_MODE = 0x10000000,
MARB_USE_SUBSYSTEM_IDS = 0x20000000,
};
#define PLX_BIGEND_REG 0xc
enum bigend_bits {
BIGEND_CONFIG = 0x1, /* use big endian ordering for configuration register accesses */
/* use big endian ordering for configuration register accesses */
BIGEND_CONFIG = 0x1,
BIGEND_DIRECT_MASTER = 0x2,
BIGEND_DIRECT_SLAVE_LOCAL0 = 0x4,
BIGEND_ROM = 0x8,
BIGEND_BYTE_LANE = 0x10, /* use byte lane consisting of most significant bits instead of least significant */
/*
* use byte lane consisting of most significant bits instead of
* least significant
*/
BIGEND_BYTE_LANE = 0x10,
BIGEND_DIRECT_SLAVE_LOCAL1 = 0x20,
BIGEND_DMA1 = 0x40,
BIGEND_DMA0 = 0x80,
};
/* Note: The Expansion ROM stuff is only relevant to the PC environment.
/*
** Note: The Expansion ROM stuff is only relevant to the PC environment.
** This expansion ROM code is executed by the host CPU at boot time.
** For this reason no bit definitions are provided here.
*/
*/
#define PLX_ROMRNG_REG 0x0010 /* L, Expn ROM Space Range Register */
#define PLX_ROMMAP_REG 0x0014 /* L, Local Addr Space Range Register */
/* L, Local Addr Space Range Register */
#define PLX_ROMMAP_REG 0x0014
#define PLX_REGION0_REG 0x0018 /* L, Local Bus Region 0 Descriptor */
#define RGN_WIDTH 0x00000002 /* Local bus width bits */
......@@ -190,7 +211,8 @@ enum bigend_bits {
#define ICS_TA_DMA0 0x02000000 /* Target Abort - DMA #0 */
#define ICS_TA_DMA1 0x04000000 /* Target Abort - DMA #1 */
#define ICS_TA_RA 0x08000000 /* Target Abort - Retry Timeout */
#define ICS_MBIA(x) (0x10000000 << ((x) & 0x3)) /* mailbox x is active */
/* mailbox x is active */
#define ICS_MBIA(x) (0x10000000 << ((x) & 0x3))
#define PLX_CONTROL_REG 0x006C /* L, EEPROM Cntl & PCI Cmd Codes */
#define CTL_RDMA 0x0000000E /* DMA Read Command */
......@@ -221,28 +243,38 @@ enum bigend_bits {
#define PLX_EN_BTERM_BIT 0x80 /* enable BTERM# input */
#define PLX_DMA_LOCAL_BURST_EN_BIT 0x100 /* enable local burst mode */
#define PLX_EN_CHAIN_BIT 0x200 /* enables chaining */
#define PLX_EN_DMA_DONE_INTR_BIT 0x400 /* enables interrupt on dma done */
#define PLX_LOCAL_ADDR_CONST_BIT 0x800 /* hold local address constant (don't increment) */
#define PLX_DEMAND_MODE_BIT 0x1000 /* enables demand-mode for dma transfer */
/* enables interrupt on dma done */
#define PLX_EN_DMA_DONE_INTR_BIT 0x400
/* hold local address constant (don't increment) */
#define PLX_LOCAL_ADDR_CONST_BIT 0x800
/* enables demand-mode for dma transfer */
#define PLX_DEMAND_MODE_BIT 0x1000
#define PLX_EOT_ENABLE_BIT 0x4000
#define PLX_STOP_MODE_BIT 0x8000
#define PLX_DMA_INTR_PCI_BIT 0x20000 /* routes dma interrupt to pci bus (instead of local bus) */
/* routes dma interrupt to pci bus (instead of local bus) */
#define PLX_DMA_INTR_PCI_BIT 0x20000
#define PLX_DMA0_PCI_ADDRESS_REG 0x84 /* pci address that dma transfers start at */
/* pci address that dma transfers start at */
#define PLX_DMA0_PCI_ADDRESS_REG 0x84
#define PLX_DMA1_PCI_ADDRESS_REG 0x98
#define PLX_DMA0_LOCAL_ADDRESS_REG 0x88 /* local address that dma transfers start at */
/* local address that dma transfers start at */
#define PLX_DMA0_LOCAL_ADDRESS_REG 0x88
#define PLX_DMA1_LOCAL_ADDRESS_REG 0x9c
#define PLX_DMA0_TRANSFER_SIZE_REG 0x8c /* number of bytes to transfer (first 23 bits) */
/* number of bytes to transfer (first 23 bits) */
#define PLX_DMA0_TRANSFER_SIZE_REG 0x8c
#define PLX_DMA1_TRANSFER_SIZE_REG 0xa0
#define PLX_DMA0_DESCRIPTOR_REG 0x90 /* descriptor pointer register */
#define PLX_DMA1_DESCRIPTOR_REG 0xa4
#define PLX_DESC_IN_PCI_BIT 0x1 /* descriptor is located in pci space (not local space) */
/* descriptor is located in pci space (not local space) */
#define PLX_DESC_IN_PCI_BIT 0x1
#define PLX_END_OF_CHAIN_BIT 0x2 /* end of chain bit */
#define PLX_INTR_TERM_COUNT 0x4 /* interrupt when this descriptor's transfer is finished */
#define PLX_XFER_LOCAL_TO_PCI 0x8 /* transfer from local to pci bus (not pci to local) */
/* interrupt when this descriptor's transfer is finished */
#define PLX_INTR_TERM_COUNT 0x4
/* transfer from local to pci bus (not pci to local) */
#define PLX_XFER_LOCAL_TO_PCI 0x8
#define PLX_DMA0_CS_REG 0xa8 /* command status register */
#define PLX_DMA1_CS_REG 0xa9
......@@ -288,10 +320,11 @@ enum bigend_bits {
#define MBX_STS_PCIRESET 0x00000100 /* Host issued PCI reset request */
#define MBX_STS_BUSY 0x00000080 /* PUTS is in progress */
#define MBX_STS_ERROR 0x00000040 /* PUTS has failed */
#define MBX_STS_RESERVED 0x000000c0 /* Undefined -> status in transition.
We are in process of changing
bits; we SET Error bit before
RESET of Busy bit */
/*
* Undefined -> status in transition. We are in process of changing bits;
* we SET Error bit before RESET of Busy bit
*/
#define MBX_STS_RESERVED 0x000000c0
#define MBX_RESERVED_5 0x00000020 /* FYI: reserved/unused bit */
#define MBX_RESERVED_4 0x00000010 /* FYI: reserved/unused bit */
......@@ -320,12 +353,12 @@ enum bigend_bits {
#define MBX_CMD_BSWAP_0 0x8c000000 /* use scheme 0 */
#define MBX_CMD_BSWAP_1 0x8c000001 /* use scheme 1 */
#define MBX_CMD_SETHMS 0x8d000000 /* setup host memory access window
size */
#define MBX_CMD_SETHBA 0x8e000000 /* setup host memory access base
address */
#define MBX_CMD_MGO 0x8f000000 /* perform memory setup and continue
(IE. Done) */
/* setup host memory access window size */
#define MBX_CMD_SETHMS 0x8d000000
/* setup host memory access base address */
#define MBX_CMD_SETHBA 0x8e000000
/* perform memory setup and continue (IE. Done) */
#define MBX_CMD_MGO 0x8f000000
#define MBX_CMD_NOOP 0xFF000000 /* dummy, illegal command */
/*****************************************/
......@@ -348,7 +381,8 @@ enum bigend_bits {
/***************************************/
#define MBX_BTYPE_MASK 0x0000ffff /* PUTS Board Type Register */
#define MBX_BTYPE_FAMILY_MASK 0x0000ff00 /* PUTS Board Family Register */
/* PUTS Board Family Register */
#define MBX_BTYPE_FAMILY_MASK 0x0000ff00
#define MBX_BTYPE_SUBTYPE_MASK 0x000000ff /* PUTS Board Subtype */
#define MBX_BTYPE_PLX9060 0x00000100 /* PLX family type */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册