x86: let 64 bit to use 32 bit calibrate_apic_clock

Use the 32-bit APIC calibration code - it's more mature.
Signed-of-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

arch/x86/kernel/apic.c

@@ -478,90 +478,6 @@ static void __cpuinit setup_APIC_timer(void)
 	clockevents_register_device(levt);
 }
 
-#ifdef CONFIG_X86_64
-/*
- * In this function we calibrate APIC bus clocks to the external
- * timer. Unfortunately we cannot use jiffies and the timer irq
- * to calibrate, since some later bootup code depends on getting
- * the first irq? Ugh.
- *
- * We want to do the calibration only once since we
- * want to have local timer irqs syncron. CPUs connected
- * by the same APIC bus have the very same bus frequency.
- * And we want to have irqs off anyways, no accidental
- * APIC irq that way.
- */
-
-#define TICK_COUNT 100000000
-
-static int __init calibrate_APIC_clock(void)
-{
-	unsigned apic, apic_start;
-	unsigned long tsc, tsc_start;
-	int result;
-
-	local_irq_disable();
-
-	/*
-	 * Put whatever arbitrary (but long enough) timeout
-	 * value into the APIC clock, we just want to get the
-	 * counter running for calibration.
-	 *
-	 * No interrupt enable !
-	 */
-	__setup_APIC_LVTT(250000000, 0, 0);
-
-	apic_start = apic_read(APIC_TMCCT);
-#ifdef CONFIG_X86_PM_TIMER
-	if (apic_calibrate_pmtmr && pmtmr_ioport) {
-		pmtimer_wait(5000);  /* 5ms wait */
-		apic = apic_read(APIC_TMCCT);
-		result = (apic_start - apic) * 1000L / 5;
-	} else
-#endif
-	{
-		rdtscll(tsc_start);
-
-		do {
-			apic = apic_read(APIC_TMCCT);
-			rdtscll(tsc);
-		} while ((tsc - tsc_start) < TICK_COUNT &&
-				(apic_start - apic) < TICK_COUNT);
-
-		result = (apic_start - apic) * 1000L * tsc_khz /
-					(tsc - tsc_start);
-	}
-
-	local_irq_enable();
-
-	printk(KERN_DEBUG "APIC timer calibration result %d\n", result);
-
-	printk(KERN_INFO "Detected %d.%03d MHz APIC timer.\n",
-		result / 1000 / 1000, result / 1000 % 1000);
-
-	/* Calculate the scaled math multiplication factor */
-	lapic_clockevent.mult = div_sc(result, NSEC_PER_SEC,
-				       lapic_clockevent.shift);
-	lapic_clockevent.max_delta_ns =
-		clockevent_delta2ns(0x7FFFFF, &lapic_clockevent);
-	lapic_clockevent.min_delta_ns =
-		clockevent_delta2ns(0xF, &lapic_clockevent);
-
-	calibration_result = (result * APIC_DIVISOR) / HZ;
-
-	/*
-	 * Do a sanity check on the APIC calibration result
-	 */
-	if (calibration_result < (1000000 / HZ)) {
-		printk(KERN_WARNING
-			"APIC frequency too slow, disabling apic timer\n");
-		return -1;
-	}
-
-	return 0;
-}
-
-#else
 /*
  * In this functions we calibrate APIC bus clocks to the external timer.
  *
@@ -659,6 +575,7 @@ static int __init calibrate_APIC_clock(void)
 	delta = lapic_cal_t1 - lapic_cal_t2;
 	apic_printk(APIC_VERBOSE, "... lapic delta = %ld\n", delta);
 
+#ifdef CONFIG_X86_PM_TIMER
 	/* Check, if the PM timer is available */
 	deltapm = lapic_cal_pm2 - lapic_cal_pm1;
 	apic_printk(APIC_VERBOSE, "... PM timer delta = %ld\n", deltapm);
@@ -687,6 +604,7 @@ static int __init calibrate_APIC_clock(void)
 		}
 		pm_referenced = 1;
 	}
+#endif
 
 	/* Calculate the scaled math multiplication factor */
 	lapic_clockevent.mult = div_sc(delta, TICK_NSEC * LAPIC_CAL_LOOPS,
@@ -773,8 +691,6 @@ static int __init calibrate_APIC_clock(void)
 	return 0;
 }
 
-#endif
-
 /*
  * Setup the boot APIC
  *