提交 e3e081e1 编写于 作者: S Santwona Behera 提交者: David S. Miller

NIU: Add Sun CP3260 ATCA blade support

This patch adds support for the Sun CP3260 ATCA blade which is
a N2 based ATCA blade with 2 NIU ports. The NIU ports do not
have on-board PHY.
Signed-off-by: NSantwona Behera <santwona.behera@sun.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 e8f6fbf6
......@@ -406,7 +406,7 @@ static int esr2_set_rx_cfg(struct niu *np, unsigned long channel, u32 val)
}
/* Mode is always 10G fiber. */
static int serdes_init_niu(struct niu *np)
static int serdes_init_niu_10g_fiber(struct niu *np)
{
struct niu_link_config *lp = &np->link_config;
u32 tx_cfg, rx_cfg;
......@@ -443,6 +443,223 @@ static int serdes_init_niu(struct niu *np)
return 0;
}
static int serdes_init_niu_1g_serdes(struct niu *np)
{
struct niu_link_config *lp = &np->link_config;
u16 pll_cfg, pll_sts;
int max_retry = 100;
u64 sig, mask, val;
u32 tx_cfg, rx_cfg;
unsigned long i;
int err;
tx_cfg = (PLL_TX_CFG_ENTX | PLL_TX_CFG_SWING_1375MV |
PLL_TX_CFG_RATE_HALF);
rx_cfg = (PLL_RX_CFG_ENRX | PLL_RX_CFG_TERM_0P8VDDT |
PLL_RX_CFG_ALIGN_ENA | PLL_RX_CFG_LOS_LTHRESH |
PLL_RX_CFG_RATE_HALF);
if (np->port == 0)
rx_cfg |= PLL_RX_CFG_EQ_LP_ADAPTIVE;
if (lp->loopback_mode == LOOPBACK_PHY) {
u16 test_cfg = PLL_TEST_CFG_LOOPBACK_CML_DIS;
mdio_write(np, np->port, NIU_ESR2_DEV_ADDR,
ESR2_TI_PLL_TEST_CFG_L, test_cfg);
tx_cfg |= PLL_TX_CFG_ENTEST;
rx_cfg |= PLL_RX_CFG_ENTEST;
}
/* Initialize PLL for 1G */
pll_cfg = (PLL_CFG_ENPLL | PLL_CFG_MPY_8X);
err = mdio_write(np, np->port, NIU_ESR2_DEV_ADDR,
ESR2_TI_PLL_CFG_L, pll_cfg);
if (err) {
dev_err(np->device, PFX "NIU Port %d "
"serdes_init_niu_1g_serdes: "
"mdio write to ESR2_TI_PLL_CFG_L failed", np->port);
return err;
}
pll_sts = PLL_CFG_ENPLL;
err = mdio_write(np, np->port, NIU_ESR2_DEV_ADDR,
ESR2_TI_PLL_STS_L, pll_sts);
if (err) {
dev_err(np->device, PFX "NIU Port %d "
"serdes_init_niu_1g_serdes: "
"mdio write to ESR2_TI_PLL_STS_L failed", np->port);
return err;
}
udelay(200);
/* Initialize all 4 lanes of the SERDES. */
for (i = 0; i < 4; i++) {
err = esr2_set_tx_cfg(np, i, tx_cfg);
if (err)
return err;
}
for (i = 0; i < 4; i++) {
err = esr2_set_rx_cfg(np, i, rx_cfg);
if (err)
return err;
}
switch (np->port) {
case 0:
val = (ESR_INT_SRDY0_P0 | ESR_INT_DET0_P0);
mask = val;
break;
case 1:
val = (ESR_INT_SRDY0_P1 | ESR_INT_DET0_P1);
mask = val;
break;
default:
return -EINVAL;
}
while (max_retry--) {
sig = nr64(ESR_INT_SIGNALS);
if ((sig & mask) == val)
break;
mdelay(500);
}
if ((sig & mask) != val) {
dev_err(np->device, PFX "Port %u signal bits [%08x] are not "
"[%08x]\n", np->port, (int) (sig & mask), (int) val);
return -ENODEV;
}
return 0;
}
static int serdes_init_niu_10g_serdes(struct niu *np)
{
struct niu_link_config *lp = &np->link_config;
u32 tx_cfg, rx_cfg, pll_cfg, pll_sts;
int max_retry = 100;
u64 sig, mask, val;
unsigned long i;
int err;
tx_cfg = (PLL_TX_CFG_ENTX | PLL_TX_CFG_SWING_1375MV);
rx_cfg = (PLL_RX_CFG_ENRX | PLL_RX_CFG_TERM_0P8VDDT |
PLL_RX_CFG_ALIGN_ENA | PLL_RX_CFG_LOS_LTHRESH |
PLL_RX_CFG_EQ_LP_ADAPTIVE);
if (lp->loopback_mode == LOOPBACK_PHY) {
u16 test_cfg = PLL_TEST_CFG_LOOPBACK_CML_DIS;
mdio_write(np, np->port, NIU_ESR2_DEV_ADDR,
ESR2_TI_PLL_TEST_CFG_L, test_cfg);
tx_cfg |= PLL_TX_CFG_ENTEST;
rx_cfg |= PLL_RX_CFG_ENTEST;
}
/* Initialize PLL for 10G */
pll_cfg = (PLL_CFG_ENPLL | PLL_CFG_MPY_10X);
err = mdio_write(np, np->port, NIU_ESR2_DEV_ADDR,
ESR2_TI_PLL_CFG_L, pll_cfg & 0xffff);
if (err) {
dev_err(np->device, PFX "NIU Port %d "
"serdes_init_niu_10g_serdes: "
"mdio write to ESR2_TI_PLL_CFG_L failed", np->port);
return err;
}
pll_sts = PLL_CFG_ENPLL;
err = mdio_write(np, np->port, NIU_ESR2_DEV_ADDR,
ESR2_TI_PLL_STS_L, pll_sts & 0xffff);
if (err) {
dev_err(np->device, PFX "NIU Port %d "
"serdes_init_niu_10g_serdes: "
"mdio write to ESR2_TI_PLL_STS_L failed", np->port);
return err;
}
udelay(200);
/* Initialize all 4 lanes of the SERDES. */
for (i = 0; i < 4; i++) {
err = esr2_set_tx_cfg(np, i, tx_cfg);
if (err)
return err;
}
for (i = 0; i < 4; i++) {
err = esr2_set_rx_cfg(np, i, rx_cfg);
if (err)
return err;
}
/* check if serdes is ready */
switch (np->port) {
case 0:
mask = ESR_INT_SIGNALS_P0_BITS;
val = (ESR_INT_SRDY0_P0 |
ESR_INT_DET0_P0 |
ESR_INT_XSRDY_P0 |
ESR_INT_XDP_P0_CH3 |
ESR_INT_XDP_P0_CH2 |
ESR_INT_XDP_P0_CH1 |
ESR_INT_XDP_P0_CH0);
break;
case 1:
mask = ESR_INT_SIGNALS_P1_BITS;
val = (ESR_INT_SRDY0_P1 |
ESR_INT_DET0_P1 |
ESR_INT_XSRDY_P1 |
ESR_INT_XDP_P1_CH3 |
ESR_INT_XDP_P1_CH2 |
ESR_INT_XDP_P1_CH1 |
ESR_INT_XDP_P1_CH0);
break;
default:
return -EINVAL;
}
while (max_retry--) {
sig = nr64(ESR_INT_SIGNALS);
if ((sig & mask) == val)
break;
mdelay(500);
}
if ((sig & mask) != val) {
pr_info(PFX "NIU Port %u signal bits [%08x] are not "
"[%08x] for 10G...trying 1G\n",
np->port, (int) (sig & mask), (int) val);
/* 10G failed, try initializing at 1G */
err = serdes_init_niu_1g_serdes(np);
if (!err) {
np->flags &= ~NIU_FLAGS_10G;
np->mac_xcvr = MAC_XCVR_PCS;
} else {
dev_err(np->device, PFX "Port %u 10G/1G SERDES "
"Link Failed \n", np->port);
return -ENODEV;
}
}
return 0;
}
static int esr_read_rxtx_ctrl(struct niu *np, unsigned long chan, u32 *val)
{
int err;
......@@ -1954,13 +2171,23 @@ static const struct niu_phy_ops phy_ops_10g_serdes = {
.link_status = link_status_10g_serdes,
};
static const struct niu_phy_ops phy_ops_10g_serdes_niu = {
.serdes_init = serdes_init_niu_10g_serdes,
.link_status = link_status_10g_serdes,
};
static const struct niu_phy_ops phy_ops_1g_serdes_niu = {
.serdes_init = serdes_init_niu_1g_serdes,
.link_status = link_status_1g_serdes,
};
static const struct niu_phy_ops phy_ops_1g_rgmii = {
.xcvr_init = xcvr_init_1g_rgmii,
.link_status = link_status_1g_rgmii,
};
static const struct niu_phy_ops phy_ops_10g_fiber_niu = {
.serdes_init = serdes_init_niu,
.serdes_init = serdes_init_niu_10g_fiber,
.xcvr_init = xcvr_init_10g,
.link_status = link_status_10g,
};
......@@ -1998,11 +2225,21 @@ struct niu_phy_template {
u32 phy_addr_base;
};
static const struct niu_phy_template phy_template_niu = {
static const struct niu_phy_template phy_template_niu_10g_fiber = {
.ops = &phy_ops_10g_fiber_niu,
.phy_addr_base = 16,
};
static const struct niu_phy_template phy_template_niu_10g_serdes = {
.ops = &phy_ops_10g_serdes_niu,
.phy_addr_base = 0,
};
static const struct niu_phy_template phy_template_niu_1g_serdes = {
.ops = &phy_ops_1g_serdes_niu,
.phy_addr_base = 0,
};
static const struct niu_phy_template phy_template_10g_fiber = {
.ops = &phy_ops_10g_fiber,
.phy_addr_base = 8,
......@@ -2182,8 +2419,25 @@ static int niu_determine_phy_disposition(struct niu *np)
u32 phy_addr_off = 0;
if (plat_type == PLAT_TYPE_NIU) {
tp = &phy_template_niu;
phy_addr_off += np->port;
switch (np->flags &
(NIU_FLAGS_10G |
NIU_FLAGS_FIBER |
NIU_FLAGS_XCVR_SERDES)) {
case NIU_FLAGS_10G | NIU_FLAGS_XCVR_SERDES:
/* 10G Serdes */
tp = &phy_template_niu_10g_serdes;
break;
case NIU_FLAGS_XCVR_SERDES:
/* 1G Serdes */
tp = &phy_template_niu_1g_serdes;
break;
case NIU_FLAGS_10G | NIU_FLAGS_FIBER:
/* 10G Fiber */
default:
tp = &phy_template_niu_10g_fiber;
phy_addr_off += np->port;
break;
}
} else {
switch (np->flags &
(NIU_FLAGS_10G |
......@@ -7213,6 +7467,12 @@ static int __devinit niu_phy_type_prop_decode(struct niu *np,
np->flags |= NIU_FLAGS_10G;
np->flags &= ~NIU_FLAGS_FIBER;
np->mac_xcvr = MAC_XCVR_XPCS;
} else if (!strcmp(phy_prop, "xgsd") || !strcmp(phy_prop, "gsd")) {
/* 10G Serdes or 1G Serdes, default to 10G */
np->flags |= NIU_FLAGS_10G;
np->flags &= ~NIU_FLAGS_FIBER;
np->flags |= NIU_FLAGS_XCVR_SERDES;
np->mac_xcvr = MAC_XCVR_XPCS;
} else {
return -EINVAL;
}
......@@ -7741,6 +8001,8 @@ static int __devinit walk_phys(struct niu *np, struct niu_parent *parent)
u32 val;
int err;
num_10g = num_1g = 0;
if (!strcmp(np->vpd.model, NIU_ALONSO_MDL_STR) ||
!strcmp(np->vpd.model, NIU_KIMI_MDL_STR)) {
num_10g = 0;
......@@ -7757,6 +8019,16 @@ static int __devinit walk_phys(struct niu *np, struct niu_parent *parent)
parent->num_ports = 2;
val = (phy_encode(PORT_TYPE_10G, 0) |
phy_encode(PORT_TYPE_10G, 1));
} else if ((np->flags & NIU_FLAGS_XCVR_SERDES) &&
(parent->plat_type == PLAT_TYPE_NIU)) {
/* this is the Monza case */
if (np->flags & NIU_FLAGS_10G) {
val = (phy_encode(PORT_TYPE_10G, 0) |
phy_encode(PORT_TYPE_10G, 1));
} else {
val = (phy_encode(PORT_TYPE_1G, 0) |
phy_encode(PORT_TYPE_1G, 1));
}
} else {
err = fill_phy_probe_info(np, parent, info);
if (err)
......@@ -8656,7 +8928,9 @@ static void __devinit niu_device_announce(struct niu *np)
dev->name,
(np->flags & NIU_FLAGS_XMAC ? "XMAC" : "BMAC"),
(np->flags & NIU_FLAGS_10G ? "10G" : "1G"),
(np->flags & NIU_FLAGS_FIBER ? "FIBER" : "COPPER"),
(np->flags & NIU_FLAGS_FIBER ? "FIBER" :
(np->flags & NIU_FLAGS_XCVR_SERDES ? "SERDES" :
"COPPER")),
(np->mac_xcvr == MAC_XCVR_MII ? "MII" :
(np->mac_xcvr == MAC_XCVR_PCS ? "PCS" : "XPCS")),
np->vpd.phy_type);
......
......@@ -1048,6 +1048,13 @@
#define PLL_CFG_LD_SHIFT 8
#define PLL_CFG_MPY 0x0000001e
#define PLL_CFG_MPY_SHIFT 1
#define PLL_CFG_MPY_4X 0x0
#define PLL_CFG_MPY_5X 0x00000002
#define PLL_CFG_MPY_6X 0x00000004
#define PLL_CFG_MPY_8X 0x00000008
#define PLL_CFG_MPY_10X 0x0000000a
#define PLL_CFG_MPY_12X 0x0000000c
#define PLL_CFG_MPY_12P5X 0x0000000e
#define PLL_CFG_ENPLL 0x00000001
#define ESR2_TI_PLL_STS_L (ESR2_BASE + 0x002)
......@@ -1093,6 +1100,9 @@
#define PLL_TX_CFG_INVPAIR 0x00000080
#define PLL_TX_CFG_RATE 0x00000060
#define PLL_TX_CFG_RATE_SHIFT 5
#define PLL_TX_CFG_RATE_FULL 0x0
#define PLL_TX_CFG_RATE_HALF 0x20
#define PLL_TX_CFG_RATE_QUAD 0x40
#define PLL_TX_CFG_BUSWIDTH 0x0000001c
#define PLL_TX_CFG_BUSWIDTH_SHIFT 2
#define PLL_TX_CFG_ENTEST 0x00000002
......@@ -1132,6 +1142,9 @@
#define PLL_RX_CFG_INVPAIR 0x00000080
#define PLL_RX_CFG_RATE 0x00000060
#define PLL_RX_CFG_RATE_SHIFT 5
#define PLL_RX_CFG_RATE_FULL 0x0
#define PLL_RX_CFG_RATE_HALF 0x20
#define PLL_RX_CFG_RATE_QUAD 0x40
#define PLL_RX_CFG_BUSWIDTH 0x0000001c
#define PLL_RX_CFG_BUSWIDTH_SHIFT 2
#define PLL_RX_CFG_ENTEST 0x00000002
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册