提交 e307ff0f 编写于 作者: A Andy Shevchenko 提交者: Greg Kroah-Hartman

usb: host: pci_quirks: joing string literals

The patch joins the string literals for happy debugging. There is no functional
change.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <greg@kroah.com>
上级 074f9dd5
......@@ -603,9 +603,9 @@ static void quirk_usb_handoff_ohci(struct pci_dev *pdev)
msleep(10);
}
if (wait_time <= 0)
dev_warn(&pdev->dev, "OHCI: BIOS handoff failed"
" (BIOS bug?) %08x\n",
readl(base + OHCI_CONTROL));
dev_warn(&pdev->dev,
"OHCI: BIOS handoff failed (BIOS bug?) %08x\n",
readl(base + OHCI_CONTROL));
}
#endif
......@@ -733,8 +733,9 @@ static void ehci_bios_handoff(struct pci_dev *pdev,
* and hope nothing goes too wrong
*/
if (try_handoff)
dev_warn(&pdev->dev, "EHCI: BIOS handoff failed"
" (BIOS bug?) %08x\n", cap);
dev_warn(&pdev->dev,
"EHCI: BIOS handoff failed (BIOS bug?) %08x\n",
cap);
pci_write_config_byte(pdev, offset + 2, 0);
}
......@@ -781,8 +782,9 @@ static void quirk_usb_disable_ehci(struct pci_dev *pdev)
case 0: /* Illegal reserved cap, set cap=0 so we exit */
cap = 0; /* then fallthrough... */
default:
dev_warn(&pdev->dev, "EHCI: unrecognized capability "
"%02x\n", cap & 0xff);
dev_warn(&pdev->dev,
"EHCI: unrecognized capability %02x\n",
cap & 0xff);
}
offset = (cap >> 8) & 0xff;
}
......@@ -893,8 +895,7 @@ void usb_enable_intel_xhci_ports(struct pci_dev *xhci_pdev)
*/
if (!IS_ENABLED(CONFIG_USB_XHCI_HCD)) {
dev_warn(&xhci_pdev->dev,
"CONFIG_USB_XHCI_HCD is turned off, "
"defaulting to EHCI.\n");
"CONFIG_USB_XHCI_HCD is turned off, defaulting to EHCI.\n");
dev_warn(&xhci_pdev->dev,
"USB 3.0 devices will work at USB 2.0 speeds.\n");
usb_disable_xhci_ports(xhci_pdev);
......@@ -919,8 +920,9 @@ void usb_enable_intel_xhci_ports(struct pci_dev *xhci_pdev)
pci_read_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN,
&ports_available);
dev_dbg(&xhci_pdev->dev, "USB 3.0 ports that are now enabled "
"under xHCI: 0x%x\n", ports_available);
dev_dbg(&xhci_pdev->dev,
"USB 3.0 ports that are now enabled under xHCI: 0x%x\n",
ports_available);
/* Read XUSB2PRM, xHCI USB 2.0 Port Routing Mask Register
* Indicate the USB 2.0 ports to be controlled by the xHCI host.
......@@ -941,8 +943,9 @@ void usb_enable_intel_xhci_ports(struct pci_dev *xhci_pdev)
pci_read_config_dword(xhci_pdev, USB_INTEL_XUSB2PR,
&ports_available);
dev_dbg(&xhci_pdev->dev, "USB 2.0 ports that are now switched over "
"to xHCI: 0x%x\n", ports_available);
dev_dbg(&xhci_pdev->dev,
"USB 2.0 ports that are now switched over to xHCI: 0x%x\n",
ports_available);
}
EXPORT_SYMBOL_GPL(usb_enable_intel_xhci_ports);
......@@ -1010,8 +1013,9 @@ static void quirk_usb_handoff_xhci(struct pci_dev *pdev)
/* Assume a buggy BIOS and take HC ownership anyway */
if (timeout) {
dev_warn(&pdev->dev, "xHCI BIOS handoff failed"
" (BIOS bug ?) %08x\n", val);
dev_warn(&pdev->dev,
"xHCI BIOS handoff failed (BIOS bug ?) %08x\n",
val);
writel(val & ~XHCI_HC_BIOS_OWNED, base + ext_cap_offset);
}
}
......@@ -1039,8 +1043,8 @@ static void quirk_usb_handoff_xhci(struct pci_dev *pdev)
if (timeout) {
val = readl(op_reg_base + XHCI_STS_OFFSET);
dev_warn(&pdev->dev,
"xHCI HW not ready after 5 sec (HC bug?) "
"status = 0x%x\n", val);
"xHCI HW not ready after 5 sec (HC bug?) status = 0x%x\n",
val);
}
/* Send the halt and disable interrupts command */
......@@ -1054,8 +1058,8 @@ static void quirk_usb_handoff_xhci(struct pci_dev *pdev)
if (timeout) {
val = readl(op_reg_base + XHCI_STS_OFFSET);
dev_warn(&pdev->dev,
"xHCI HW did not halt within %d usec "
"status = 0x%x\n", XHCI_MAX_HALT_USEC, val);
"xHCI HW did not halt within %d usec status = 0x%x\n",
XHCI_MAX_HALT_USEC, val);
}
iounmap(base);
......@@ -1075,8 +1079,8 @@ static void quirk_usb_early_handoff(struct pci_dev *pdev)
return;
if (pci_enable_device(pdev) < 0) {
dev_warn(&pdev->dev, "Can't enable PCI device, "
"BIOS handoff failed.\n");
dev_warn(&pdev->dev,
"Can't enable PCI device, BIOS handoff failed.\n");
return;
}
if (pdev->class == PCI_CLASS_SERIAL_USB_UHCI)
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册