Merge tag 'spi-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into next

Pull spi updates from Mark Brown:
 "For this release SPI has been exceptionally quiet, all the work has
  been on improving drivers (including taking advantage of some of the
  recent framework updates):

   - DMA support for the rspi driver providing a nice performance boost
   - performance improvement for the SIRF controller in PIO mode
   - new support for the Cadence SPI IP and for pxa2xx on BayTrail"

* tag 'spi-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (59 commits)
  spi: rspi: Extract rspi_common_transfer()
  spi: rspi: Add DMA support for RSPI on RZ/A1H
  spi: rspi: Add DMA support for QSPI on R-Car Gen2
  spi: rspi: Absorb rspi_rz_transfer_out_in() into rspi_rz_transfer_one()
  spi: rspi: Merge rspi_*_dma() into rspi_dma_transfer()
  spi: rspi: Pass sg_tables instead of spi_tranfer to rspi_*_dma()
  spi: rspi: Move RSPI-specific setup out of DMA routines
  spi: rspi: Use SPI core DMA mapping framework
  spi: rspi: SPI DMA core needs both RX and TX DMA to function
  spi: rspi: Remove unneeded resource test in DMA setup
  spi: rspi: Extract rspi_request_dma_chan()
  spi: rspi: Don't consider DMA configuration failures fatal
  spi: rspi: Extract rspi_pio_transfer()
  spi: rspi: Use core SPI_MASTER_MUST_[RT]X handling
  spi: rspi: Remove unused 16-bit DMA support
  spi: rspi: Do not call rspi_receive_init() for TX-only
  spi: rspi: Extract rspi_wait_for_{tx_empty,rx_full}()
  spi/pxa2xx: fix runtime PM enabling order
  spi/fsl-espi: fix rx_buf in fsl_espi_cmd_trans()/fsl_espi_rw_trans()
  spi: core: Ignore unsupported spi-[tr]x-bus-width property values
  ...

Documentation/devicetree/bindings/spi/fsl-spi.txt

@@ -42,6 +42,10 @@ Required properties:
 - interrupts : should contain eSPI interrupt, the device has one interrupt.
 - fsl,espi-num-chipselects : the number of the chipselect signals.
 
+Optional properties:
+- fsl,csbef: chip select assertion time in bits before frame starts
+- fsl,csaft: chip select negation time in bits after frame ends
+
 Example:
 	spi@110000 {
 		#address-cells = <1>;
@@ -51,4 +55,6 @@ Example:
 		interrupts = <53 0x2>;
 		interrupt-parent = <&mpic>;
 		fsl,espi-num-chipselects = <4>;
+		fsl,csbef = <1>;
+		fsl,csaft = <1>;
 	};

Documentation/devicetree/bindings/spi/spi-bus.txt

@@ -55,6 +55,8 @@ contain the following properties.
     		chip select active high
 - spi-3wire       - (optional) Empty property indicating device requires
     		    3-wire mode.
+- spi-lsb-first   - (optional) Empty property indicating device requires
+		LSB first mode.
 - spi-tx-bus-width - (optional) The bus width(number of data wires) that
                       used for MOSI. Defaults to 1 if not present.
 - spi-rx-bus-width - (optional) The bus width(number of data wires) that

Documentation/devicetree/bindings/spi/spi-cadence.txt

+Cadence SPI controller Device Tree Bindings
+-------------------------------------------
+
+Required properties:
+- compatible		: Should be "cdns,spi-r1p6" or "xlnx,zynq-spi-r1p6".
+- reg			: Physical base address and size of SPI registers map.
+- interrupts		: Property with a value describing the interrupt
+			  number.
+- interrupt-parent	: Must be core interrupt controller
+- clock-names		: List of input clock names - "ref_clk", "pclk"
+			  (See clock bindings for details).
+- clocks		: Clock phandles (see clock bindings for details).
+
+Optional properties:
+- num-cs		: Number of chip selects used.
+			  If a decoder is used, this will be the number of
+			  chip selects after the decoder.
+- is-decoded-cs		: Flag to indicate whether decoder is used or not.
+
+Example:
+
+	spi@e0007000 {
+		compatible = "xlnx,zynq-spi-r1p6";
+		clock-names = "ref_clk", "pclk";
+		clocks = <&clkc 26>, <&clkc 35>;
+		interrupt-parent = <&intc>;
+		interrupts = <0 49 4>;
+		num-cs = <4>;
+		is-decoded-cs = <0>;
+		reg = <0xe0007000 0x1000>;
+	} ;

Documentation/devicetree/bindings/spi/spi-dw.txt

+Synopsys DesignWare SPI master
+
+Required properties:
+- compatible: should be "snps,designware-spi"
+- #address-cells: see spi-bus.txt
+- #size-cells: see spi-bus.txt
+- reg: address and length of the spi master registers
+- interrupts: should contain one interrupt
+- clocks: spi clock phandle
+- num-cs: see spi-bus.txt
+
+Optional properties:
+- cs-gpios: see spi-bus.txt
+
+Example:
+
+spi: spi@4020a000 {
+	compatible = "snps,designware-spi";
+	interrupts = <11 1>;
+	reg = <0x4020a000 0x1000>;
+	clocks = <&pclk>;
+	num-cs = <2>;
+	cs-gpios = <&banka 0 0>;
+};

arch/blackfin/mach-bf609/boards/ezkit.c

@@ -20,7 +20,7 @@
 #include <linux/pinctrl/machine.h>
 #include <linux/pinctrl/pinconf-generic.h>
 #include <linux/platform_data/pinctrl-adi2.h>
-#include <asm/bfin_spi3.h>
+#include <linux/spi/adi_spi3.h>
 #include <asm/dma.h>
 #include <asm/gpio.h>
 #include <asm/nand.h>
@@ -767,13 +767,13 @@ static struct flash_platform_data bfin_spi_flash_data = {
 	.type = "w25q32",
 };
 
-static struct bfin_spi3_chip spi_flash_chip_info = {
+static struct adi_spi3_chip spi_flash_chip_info = {
 	.enable_dma = true,         /* use dma transfer with this chip*/
 };
 #endif
 
 #if IS_ENABLED(CONFIG_SPI_SPIDEV)
-static struct bfin_spi3_chip spidev_chip_info = {
+static struct adi_spi3_chip spidev_chip_info = {
 	.enable_dma = true,
 };
 #endif
@@ -1736,7 +1736,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 };
-#if IS_ENABLED(CONFIG_SPI_BFIN_V3)
+#if IS_ENABLED(CONFIG_SPI_ADI_V3)
 /* SPI (0) */
 static struct resource bfin_spi0_resource[] = {
 	{
@@ -1777,13 +1777,13 @@ static struct resource bfin_spi1_resource[] = {
 };
 
 /* SPI controller data */
-static struct bfin_spi3_master bf60x_spi_master_info0 = {
+static struct adi_spi3_master bf60x_spi_master_info0 = {
 	.num_chipselect = MAX_CTRL_CS + MAX_BLACKFIN_GPIOS,
 	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 };
 
 static struct platform_device bf60x_spi_master0 = {
-	.name = "bfin-spi3",
+	.name = "adi-spi3",
 	.id = 0, /* Bus number */
 	.num_resources = ARRAY_SIZE(bfin_spi0_resource),
 	.resource = bfin_spi0_resource,
@@ -1792,13 +1792,13 @@ static struct platform_device bf60x_spi_master0 = {
 	},
 };
 
-static struct bfin_spi3_master bf60x_spi_master_info1 = {
+static struct adi_spi3_master bf60x_spi_master_info1 = {
 	.num_chipselect = MAX_CTRL_CS + MAX_BLACKFIN_GPIOS,
 	.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
 };
 
 static struct platform_device bf60x_spi_master1 = {
-	.name = "bfin-spi3",
+	.name = "adi-spi3",
 	.id = 1, /* Bus number */
 	.num_resources = ARRAY_SIZE(bfin_spi1_resource),
 	.resource = bfin_spi1_resource,
@@ -1990,7 +1990,7 @@ static struct platform_device *ezkit_devices[] __initdata = {
 	&bfin_sdh_device,
 #endif
 
-#if IS_ENABLED(CONFIG_SPI_BFIN_V3)
+#if IS_ENABLED(CONFIG_SPI_ADI_V3)
 	&bf60x_spi_master0,
 	&bf60x_spi_master1,
 #endif
@@ -2051,8 +2051,8 @@ static struct pinctrl_map __initdata bfin_pinmux_map[] = {
 	PIN_MAP_MUX_GROUP_DEFAULT("bfin_sir.1",  "pinctrl-adi2.0", NULL, "uart1"),
 	PIN_MAP_MUX_GROUP_DEFAULT("bfin-sdh.0",  "pinctrl-adi2.0", NULL, "rsi0"),
 	PIN_MAP_MUX_GROUP_DEFAULT("stmmaceth.0",  "pinctrl-adi2.0", NULL, "eth0"),
-	PIN_MAP_MUX_GROUP_DEFAULT("bfin-spi3.0",  "pinctrl-adi2.0", NULL, "spi0"),
-	PIN_MAP_MUX_GROUP_DEFAULT("bfin-spi3.1",  "pinctrl-adi2.0", NULL, "spi1"),
+	PIN_MAP_MUX_GROUP_DEFAULT("adi-spi3.0",  "pinctrl-adi2.0", NULL, "spi0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("adi-spi3.1",  "pinctrl-adi2.0", NULL, "spi1"),
 	PIN_MAP_MUX_GROUP_DEFAULT("i2c-bfin-twi.0",  "pinctrl-adi2.0", NULL, "twi0"),
 	PIN_MAP_MUX_GROUP_DEFAULT("i2c-bfin-twi.1",  "pinctrl-adi2.0", NULL, "twi1"),
 	PIN_MAP_MUX_GROUP_DEFAULT("bfin-rotary",  "pinctrl-adi2.0", NULL, "rotary"),

arch/blackfin/mach-bf609/clock.c

@@ -363,6 +363,12 @@ static struct clk ethclk = {
 	.ops	    = &dummy_clk_ops,
 };
 
+static struct clk spiclk = {
+	.name       = "spi",
+	.parent     = &sclk1,
+	.ops        = &dummy_clk_ops,
+};
+
 static struct clk_lookup bf609_clks[] = {
 	CLK(sys_clkin, NULL, "SYS_CLKIN"),
 	CLK(pll_clk, NULL, "PLLCLK"),
@@ -375,6 +381,7 @@ static struct clk_lookup bf609_clks[] = {
 	CLK(dclk, NULL, "DCLK"),
 	CLK(oclk, NULL, "OCLK"),
 	CLK(ethclk, NULL, "stmmaceth"),
+	CLK(spiclk, NULL, "spi"),
 };
 
 int __init clk_init(void)

drivers/spi/Kconfig

@@ -91,8 +91,8 @@ config SPI_BFIN5XX
 	help
 	  This is the SPI controller master driver for Blackfin 5xx processor.
 
-config SPI_BFIN_V3
-	tristate "SPI controller v3 for Blackfin"
+config SPI_ADI_V3
+	tristate "SPI controller v3 for ADI"
 	depends on BF60x
 	help
 	  This is the SPI controller v3 master driver
@@ -148,6 +148,13 @@ config SPI_BUTTERFLY
 	  inexpensive battery powered microcontroller evaluation board.
 	  This same cable can be used to flash new firmware.
 
+config SPI_CADENCE
+	tristate "Cadence SPI controller"
+	depends on ARM
+	help
+	  This selects the Cadence SPI controller master driver
+	  used by Xilinx Zynq.
+
 config SPI_CLPS711X
 	tristate "CLPS711X host SPI controller"
 	depends on ARCH_CLPS711X || COMPILE_TEST
@@ -505,7 +512,7 @@ config SPI_TEGRA20_SLINK
 
 config SPI_TOPCLIFF_PCH
 	tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
-	depends on PCI
+	depends on PCI && (X86_32 || COMPILE_TEST)
 	help
 	  SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
 	  used in some x86 embedded processors.

drivers/spi/Makefile

@@ -18,10 +18,11 @@ obj-$(CONFIG_SPI_BCM2835)		+= spi-bcm2835.o
 obj-$(CONFIG_SPI_BCM63XX)		+= spi-bcm63xx.o
 obj-$(CONFIG_SPI_BCM63XX_HSSPI)		+= spi-bcm63xx-hsspi.o
 obj-$(CONFIG_SPI_BFIN5XX)		+= spi-bfin5xx.o
-obj-$(CONFIG_SPI_BFIN_V3)               += spi-bfin-v3.o
+obj-$(CONFIG_SPI_ADI_V3)                += spi-adi-v3.o
 obj-$(CONFIG_SPI_BFIN_SPORT)		+= spi-bfin-sport.o
 obj-$(CONFIG_SPI_BITBANG)		+= spi-bitbang.o
 obj-$(CONFIG_SPI_BUTTERFLY)		+= spi-butterfly.o
+obj-$(CONFIG_SPI_CADENCE)		+= spi-cadence.o
 obj-$(CONFIG_SPI_CLPS711X)		+= spi-clps711x.o
 obj-$(CONFIG_SPI_COLDFIRE_QSPI)		+= spi-coldfire-qspi.o
 obj-$(CONFIG_SPI_DAVINCI)		+= spi-davinci.o

drivers/spi/spi-ath79.c

@@ -16,7 +16,6 @@
 #include <linux/module.h>
 #include <linux/delay.h>
 #include <linux/spinlock.h>
-#include <linux/workqueue.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/spi/spi.h>

drivers/spi/spi-atmel.c

@@ -224,7 +224,7 @@ struct atmel_spi {
 	struct platform_device	*pdev;
 
 	struct spi_transfer	*current_transfer;
-	unsigned long		current_remaining_bytes;
+	int			current_remaining_bytes;
 	int			done_status;
 
 	struct completion	xfer_completion;
@@ -874,8 +874,9 @@ atmel_spi_pump_pio_data(struct atmel_spi *as, struct spi_transfer *xfer)
 		spi_readl(as, RDR);
 	}
 	if (xfer->bits_per_word > 8) {
-		as->current_remaining_bytes -= 2;
-		if (as->current_remaining_bytes < 0)
+		if (as->current_remaining_bytes > 2)
+			as->current_remaining_bytes -= 2;
+		else
 			as->current_remaining_bytes = 0;
 	} else {
 		as->current_remaining_bytes--;
@@ -1110,6 +1111,8 @@ static int atmel_spi_one_transfer(struct spi_master *master,
 				atmel_spi_next_xfer_pio(master, xfer);
 			} else {
 				as->current_remaining_bytes -= len;
+				if (as->current_remaining_bytes < 0)
+					as->current_remaining_bytes = 0;
 			}
 		} else {
 			atmel_spi_next_xfer_pio(master, xfer);

drivers/spi/spi-bcm63xx-hsspi.c

@@ -18,7 +18,6 @@
 #include <linux/err.h>
 #include <linux/interrupt.h>
 #include <linux/spi/spi.h>
-#include <linux/workqueue.h>
 #include <linux/mutex.h>
 
 #define HSSPI_GLOBAL_CTRL_REG			0x0

drivers/spi/spi-bcm63xx.c

@@ -29,7 +29,6 @@
 #include <linux/spi/spi.h>
 #include <linux/completion.h>
 #include <linux/err.h>
-#include <linux/workqueue.h>
 #include <linux/pm_runtime.h>
 
 #include <bcm63xx_dev_spi.h>

drivers/spi/spi-dw-mmio.c

@@ -16,6 +16,7 @@
 #include <linux/spi/spi.h>
 #include <linux/scatterlist.h>
 #include <linux/module.h>
+#include <linux/of_gpio.h>
 
 #include "spi-dw.h"
 
@@ -70,6 +71,27 @@ static int dw_spi_mmio_probe(struct platform_device *pdev)
 	dws->num_cs = 4;
 	dws->max_freq = clk_get_rate(dwsmmio->clk);
 
+	if (pdev->dev.of_node) {
+		int i;
+
+		for (i = 0; i < dws->num_cs; i++) {
+			int cs_gpio = of_get_named_gpio(pdev->dev.of_node,
+					"cs-gpios", i);
+
+			if (cs_gpio == -EPROBE_DEFER) {
+				ret = cs_gpio;
+				goto out;
+			}
+
+			if (gpio_is_valid(cs_gpio)) {
+				ret = devm_gpio_request(&pdev->dev, cs_gpio,
+						dev_name(&pdev->dev));
+				if (ret)
+					goto out;
+			}
+		}
+	}
+
 	ret = dw_spi_add_host(&pdev->dev, dws);
 	if (ret)
 		goto out;

drivers/spi/spi-dw.c

@@ -24,6 +24,7 @@
 #include <linux/delay.h>
 #include <linux/slab.h>
 #include <linux/spi/spi.h>
+#include <linux/gpio.h>
 
 #include "spi-dw.h"
 
@@ -36,12 +37,6 @@
 #define DONE_STATE	((void *)2)
 #define ERROR_STATE	((void *)-1)
 
-#define QUEUE_RUNNING	0
-#define QUEUE_STOPPED	1
-
-#define MRST_SPI_DEASSERT	0
-#define MRST_SPI_ASSERT		1
-
 /* Slave spi_dev related */
 struct chip_data {
 	u16 cr0;
@@ -263,28 +258,22 @@ static int map_dma_buffers(struct dw_spi *dws)
 static void giveback(struct dw_spi *dws)
 {
 	struct spi_transfer *last_transfer;
-	unsigned long flags;
 	struct spi_message *msg;
 
-	spin_lock_irqsave(&dws->lock, flags);
 	msg = dws->cur_msg;
 	dws->cur_msg = NULL;
 	dws->cur_transfer = NULL;
 	dws->prev_chip = dws->cur_chip;
 	dws->cur_chip = NULL;
 	dws->dma_mapped = 0;
-	queue_work(dws->workqueue, &dws->pump_messages);
-	spin_unlock_irqrestore(&dws->lock, flags);
 
 	last_transfer = list_last_entry(&msg->transfers, struct spi_transfer,
 					transfer_list);
 
-	if (!last_transfer->cs_change && dws->cs_control)
-		dws->cs_control(MRST_SPI_DEASSERT);
+	if (!last_transfer->cs_change)
+		spi_chip_sel(dws, dws->cur_msg->spi, 0);
 
-	msg->state = NULL;
-	if (msg->complete)
-		msg->complete(msg->context);
+	spi_finalize_current_message(dws->master);
 }
 
 static void int_error_stop(struct dw_spi *dws, const char *msg)
@@ -502,7 +491,7 @@ static void pump_transfers(unsigned long data)
 			dw_writew(dws, DW_SPI_CTRL0, cr0);
 
 		spi_set_clk(dws, clk_div ? clk_div : chip->clk_div);
-		spi_chip_sel(dws, spi->chip_select);
+		spi_chip_sel(dws, spi, 1);
 
 		/* Set the interrupt mask, for poll mode just disable all int */
 		spi_mask_intr(dws, 0xff);
@@ -529,30 +518,12 @@ static void pump_transfers(unsigned long data)
 	return;
 }
 
-static void pump_messages(struct work_struct *work)
+static int dw_spi_transfer_one_message(struct spi_master *master,
+		struct spi_message *msg)
 {
-	struct dw_spi *dws =
-		container_of(work, struct dw_spi, pump_messages);
-	unsigned long flags;
-
-	/* Lock queue and check for queue work */
-	spin_lock_irqsave(&dws->lock, flags);
-	if (list_empty(&dws->queue) || dws->run == QUEUE_STOPPED) {
-		dws->busy = 0;
-		spin_unlock_irqrestore(&dws->lock, flags);
-		return;
-	}
-
-	/* Make sure we are not already running a message */
-	if (dws->cur_msg) {
-		spin_unlock_irqrestore(&dws->lock, flags);
-		return;
-	}
-
-	/* Extract head of queue */
-	dws->cur_msg = list_entry(dws->queue.next, struct spi_message, queue);
-	list_del_init(&dws->cur_msg->queue);
+	struct dw_spi *dws = spi_master_get_devdata(master);
 
+	dws->cur_msg = msg;
 	/* Initial message state*/
 	dws->cur_msg->state = START_STATE;
 	dws->cur_transfer = list_entry(dws->cur_msg->transfers.next,
@@ -560,46 +531,9 @@ static void pump_messages(struct work_struct *work)
 						transfer_list);
 	dws->cur_chip = spi_get_ctldata(dws->cur_msg->spi);
 
-	/* Mark as busy and launch transfers */
+	/* Launch transfers */
 	tasklet_schedule(&dws->pump_transfers);
 
-	dws->busy = 1;
-	spin_unlock_irqrestore(&dws->lock, flags);
-}
-
-/* spi_device use this to queue in their spi_msg */
-static int dw_spi_transfer(struct spi_device *spi, struct spi_message *msg)
-{
-	struct dw_spi *dws = spi_master_get_devdata(spi->master);
-	unsigned long flags;
-
-	spin_lock_irqsave(&dws->lock, flags);
-
-	if (dws->run == QUEUE_STOPPED) {
-		spin_unlock_irqrestore(&dws->lock, flags);
-		return -ESHUTDOWN;
-	}
-
-	msg->actual_length = 0;
-	msg->status = -EINPROGRESS;
-	msg->state = START_STATE;
-
-	list_add_tail(&msg->queue, &dws->queue);
-
-	if (dws->run == QUEUE_RUNNING && !dws->busy) {
-
-		if (dws->cur_transfer || dws->cur_msg)
-			queue_work(dws->workqueue,
-					&dws->pump_messages);
-		else {
-			/* If no other data transaction in air, just go */
-			spin_unlock_irqrestore(&dws->lock, flags);
-			pump_messages(&dws->pump_messages);
-			return 0;
-		}
-	}
-
-	spin_unlock_irqrestore(&dws->lock, flags);
 	return 0;
 }
 
@@ -608,6 +542,7 @@ static int dw_spi_setup(struct spi_device *spi)
 {
 	struct dw_spi_chip *chip_info = NULL;
 	struct chip_data *chip;
+	int ret;
 
 	/* Only alloc on first setup */
 	chip = spi_get_ctldata(spi);
@@ -661,81 +596,13 @@ static int dw_spi_setup(struct spi_device *spi)
 			| (spi->mode  << SPI_MODE_OFFSET)
 			| (chip->tmode << SPI_TMOD_OFFSET);
 
-	return 0;
-}
-
-static int init_queue(struct dw_spi *dws)
-{
-	INIT_LIST_HEAD(&dws->queue);
-	spin_lock_init(&dws->lock);
-
-	dws->run = QUEUE_STOPPED;
-	dws->busy = 0;
-
-	tasklet_init(&dws->pump_transfers,
-			pump_transfers,	(unsigned long)dws);
-
-	INIT_WORK(&dws->pump_messages, pump_messages);
-	dws->workqueue = create_singlethread_workqueue(
-					dev_name(dws->master->dev.parent));
-	if (dws->workqueue == NULL)
-		return -EBUSY;
-
-	return 0;
-}
-
-static int start_queue(struct dw_spi *dws)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&dws->lock, flags);
-
-	if (dws->run == QUEUE_RUNNING || dws->busy) {
-		spin_unlock_irqrestore(&dws->lock, flags);
-		return -EBUSY;
+	if (gpio_is_valid(spi->cs_gpio)) {
+		ret = gpio_direction_output(spi->cs_gpio,
+				!(spi->mode & SPI_CS_HIGH));
+		if (ret)
+			return ret;
 	}
 
-	dws->run = QUEUE_RUNNING;
-	dws->cur_msg = NULL;
-	dws->cur_transfer = NULL;
-	dws->cur_chip = NULL;
-	dws->prev_chip = NULL;
-	spin_unlock_irqrestore(&dws->lock, flags);
-
-	queue_work(dws->workqueue, &dws->pump_messages);
-
-	return 0;
-}
-
-static int stop_queue(struct dw_spi *dws)
-{
-	unsigned long flags;
-	unsigned limit = 50;
-	int status = 0;
-
-	spin_lock_irqsave(&dws->lock, flags);
-	dws->run = QUEUE_STOPPED;
-	while ((!list_empty(&dws->queue) || dws->busy) && limit--) {
-		spin_unlock_irqrestore(&dws->lock, flags);
-		msleep(10);
-		spin_lock_irqsave(&dws->lock, flags);
-	}
-
-	if (!list_empty(&dws->queue) || dws->busy)
-		status = -EBUSY;
-	spin_unlock_irqrestore(&dws->lock, flags);
-
-	return status;
-}
-
-static int destroy_queue(struct dw_spi *dws)
-{
-	int status;
-
-	status = stop_queue(dws);
-	if (status != 0)
-		return status;
-	destroy_workqueue(dws->workqueue);
 	return 0;
 }
 
@@ -794,7 +661,7 @@ int dw_spi_add_host(struct device *dev, struct dw_spi *dws)
 	master->bus_num = dws->bus_num;
 	master->num_chipselect = dws->num_cs;
 	master->setup = dw_spi_setup;
-	master->transfer = dw_spi_transfer;
+	master->transfer_one_message = dw_spi_transfer_one_message;
 	master->max_speed_hz = dws->max_freq;
 
 	/* Basic HW init */
@@ -808,33 +675,21 @@ int dw_spi_add_host(struct device *dev, struct dw_spi *dws)
 		}
 	}
 
-	/* Initial and start queue */
-	ret = init_queue(dws);
-	if (ret) {
-		dev_err(&master->dev, "problem initializing queue\n");
-		goto err_diable_hw;
-	}
-	ret = start_queue(dws);
-	if (ret) {
-		dev_err(&master->dev, "problem starting queue\n");
-		goto err_diable_hw;
-	}
+	tasklet_init(&dws->pump_transfers, pump_transfers, (unsigned long)dws);
 
 	spi_master_set_devdata(master, dws);
 	ret = devm_spi_register_master(dev, master);
 	if (ret) {
 		dev_err(&master->dev, "problem registering spi master\n");
-		goto err_queue_alloc;
+		goto err_dma_exit;
 	}
 
 	mrst_spi_debugfs_init(dws);
 	return 0;
 
-err_queue_alloc:
-	destroy_queue(dws);
+err_dma_exit:
 	if (dws->dma_ops && dws->dma_ops->dma_exit)
 		dws->dma_ops->dma_exit(dws);
-err_diable_hw:
 	spi_enable_chip(dws, 0);
 err_free_master:
 	spi_master_put(master);
@@ -844,18 +699,10 @@ EXPORT_SYMBOL_GPL(dw_spi_add_host);
 
 void dw_spi_remove_host(struct dw_spi *dws)
 {
-	int status = 0;
-
 	if (!dws)
 		return;
 	mrst_spi_debugfs_remove(dws);
 
-	/* Remove the queue */
-	status = destroy_queue(dws);
-	if (status != 0)
-		dev_err(&dws->master->dev,
-			"dw_spi_remove: workqueue will not complete, message memory not freed\n");
-
 	if (dws->dma_ops && dws->dma_ops->dma_exit)
 		dws->dma_ops->dma_exit(dws);
 	spi_enable_chip(dws, 0);
@@ -868,7 +715,7 @@ int dw_spi_suspend_host(struct dw_spi *dws)
 {
 	int ret = 0;
 
-	ret = stop_queue(dws);
+	ret = spi_master_suspend(dws->master);
 	if (ret)
 		return ret;
 	spi_enable_chip(dws, 0);
@@ -882,7 +729,7 @@ int dw_spi_resume_host(struct dw_spi *dws)
 	int ret;
 
 	spi_hw_init(dws);
-	ret = start_queue(dws);
+	ret = spi_master_resume(dws->master);
 	if (ret)
 		dev_err(&dws->master->dev, "fail to start queue (%d)\n", ret);
 	return ret;

drivers/spi/spi-dw.h

@@ -3,6 +3,7 @@
 
 #include <linux/io.h>
 #include <linux/scatterlist.h>
+#include <linux/gpio.h>
 
 /* Register offsets */
 #define DW_SPI_CTRL0			0x00
@@ -104,14 +105,6 @@ struct dw_spi {
 	u16			bus_num;
 	u16			num_cs;		/* supported slave numbers */
 
-	/* Driver message queue */
-	struct workqueue_struct	*workqueue;
-	struct work_struct	pump_messages;
-	spinlock_t		lock;
-	struct list_head	queue;
-	int			busy;
-	int			run;
-
 	/* Message Transfer pump */
 	struct tasklet_struct	pump_transfers;
 
@@ -186,15 +179,20 @@ static inline void spi_set_clk(struct dw_spi *dws, u16 div)
 	dw_writel(dws, DW_SPI_BAUDR, div);
 }
 
-static inline void spi_chip_sel(struct dw_spi *dws, u16 cs)
+static inline void spi_chip_sel(struct dw_spi *dws, struct spi_device *spi,
+		int active)
 {
-	if (cs > dws->num_cs)
-		return;
+	u16 cs = spi->chip_select;
+	int gpio_val = active ? (spi->mode & SPI_CS_HIGH) :
+		!(spi->mode & SPI_CS_HIGH);
 
 	if (dws->cs_control)
-		dws->cs_control(1);
+		dws->cs_control(active);
+	if (gpio_is_valid(spi->cs_gpio))
+		gpio_set_value(spi->cs_gpio, gpio_val);
 
-	dw_writel(dws, DW_SPI_SER, 1 << cs);
+	if (active)
+		dw_writel(dws, DW_SPI_SER, 1 << cs);
 }
 
 /* Disable IRQ bits */

drivers/spi/spi-falcon.c

@@ -11,7 +11,6 @@
 #include <linux/platform_device.h>
 #include <linux/spi/spi.h>
 #include <linux/delay.h>
-#include <linux/workqueue.h>
 #include <linux/of.h>
 #include <linux/of_platform.h>
 

drivers/spi/spi-fsl-dspi.c

@@ -406,7 +406,7 @@ static irqreturn_t dspi_interrupt(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
-static struct of_device_id fsl_dspi_dt_ids[] = {
+static const struct of_device_id fsl_dspi_dt_ids[] = {
 	{ .compatible = "fsl,vf610-dspi", .data = NULL, },
 	{ /* sentinel */ }
 };

drivers/spi/spi-fsl-espi.c

@@ -348,7 +348,7 @@ static void fsl_espi_cmd_trans(struct spi_message *m,
 	}
 
 	espi_trans->tx_buf = local_buf;
-	espi_trans->rx_buf = local_buf + espi_trans->n_tx;
+	espi_trans->rx_buf = local_buf;
 	fsl_espi_do_trans(m, espi_trans);
 
 	espi_trans->actual_length = espi_trans->len;
@@ -397,7 +397,7 @@ static void fsl_espi_rw_trans(struct spi_message *m,
 		espi_trans->n_rx = trans_len;
 		espi_trans->len = trans_len + n_tx;
 		espi_trans->tx_buf = local_buf;
-		espi_trans->rx_buf = local_buf + n_tx;
+		espi_trans->rx_buf = local_buf;
 		fsl_espi_do_trans(m, espi_trans);
 
 		memcpy(rx_buf + pos, espi_trans->rx_buf + n_tx, trans_len);
@@ -458,7 +458,7 @@ static int fsl_espi_setup(struct spi_device *spi)
 		return -EINVAL;
 
 	if (!cs) {
-		cs = kzalloc(sizeof *cs, GFP_KERNEL);
+		cs = devm_kzalloc(&spi->dev, sizeof(*cs), GFP_KERNEL);
 		if (!cs)
 			return -ENOMEM;
 		spi->controller_state = cs;
@@ -586,8 +586,10 @@ static struct spi_master * fsl_espi_probe(struct device *dev,
 	struct spi_master *master;
 	struct mpc8xxx_spi *mpc8xxx_spi;
 	struct fsl_espi_reg *reg_base;
-	u32 regval;
-	int i, ret = 0;
+	struct device_node *nc;
+	const __be32 *prop;
+	u32 regval, csmode;
+	int i, len, ret = 0;
 
 	master = spi_alloc_master(dev, sizeof(struct mpc8xxx_spi));
 	if (!master) {
@@ -634,8 +636,32 @@ static struct spi_master * fsl_espi_probe(struct device *dev,
 	mpc8xxx_spi_write_reg(&reg_base->event, 0xffffffff);
 
 	/* Init eSPI CS mode register */
-	for (i = 0; i < pdata->max_chipselect; i++)
-		mpc8xxx_spi_write_reg(&reg_base->csmode[i], CSMODE_INIT_VAL);
+	for_each_available_child_of_node(master->dev.of_node, nc) {
+		/* get chip select */
+		prop = of_get_property(nc, "reg", &len);
+		if (!prop || len < sizeof(*prop))
+			continue;
+		i = be32_to_cpup(prop);
+		if (i < 0 || i >= pdata->max_chipselect)
+			continue;
+
+		csmode = CSMODE_INIT_VAL;
+		/* check if CSBEF is set in device tree */
+		prop = of_get_property(nc, "fsl,csbef", &len);
+		if (prop && len >= sizeof(*prop)) {
+			csmode &= ~(CSMODE_BEF(0xf));
+			csmode |= CSMODE_BEF(be32_to_cpup(prop));
+		}
+		/* check if CSAFT is set in device tree */
+		prop = of_get_property(nc, "fsl,csaft", &len);
+		if (prop && len >= sizeof(*prop)) {
+			csmode &= ~(CSMODE_AFT(0xf));
+			csmode |= CSMODE_AFT(be32_to_cpup(prop));
+		}
+		mpc8xxx_spi_write_reg(&reg_base->csmode[i], csmode);
+
+		dev_info(dev, "cs=%d, init_csmode=0x%x\n", i, csmode);
+	}
 
 	/* Enable SPI interface */
 	regval = pdata->initial_spmode | SPMODE_INIT_VAL | SPMODE_ENABLE;

drivers/spi/spi-fsl-lib.c

@@ -99,11 +99,6 @@ int mpc8xxx_spi_transfer(struct spi_device *spi,
 	return 0;
 }
 
-void mpc8xxx_spi_cleanup(struct spi_device *spi)
-{
-	kfree(spi->controller_state);
-}
-
 const char *mpc8xxx_spi_strmode(unsigned int flags)
 {
 	if (flags & SPI_QE_CPU_MODE) {
@@ -134,7 +129,6 @@ int mpc8xxx_spi_probe(struct device *dev, struct resource *mem,
 			| SPI_LSB_FIRST | SPI_LOOP;
 
 	master->transfer = mpc8xxx_spi_transfer;
-	master->cleanup = mpc8xxx_spi_cleanup;
 	master->dev.of_node = dev->of_node;
 
 	mpc8xxx_spi = spi_master_get_devdata(master);

drivers/spi/spi-fsl-lib.h

@@ -124,7 +124,6 @@ extern struct mpc8xxx_spi_probe_info *to_of_pinfo(
 extern int mpc8xxx_spi_bufs(struct mpc8xxx_spi *mspi,
 		struct spi_transfer *t, unsigned int len);
 extern int mpc8xxx_spi_transfer(struct spi_device *spi, struct spi_message *m);
-extern void mpc8xxx_spi_cleanup(struct spi_device *spi);
 extern const char *mpc8xxx_spi_strmode(unsigned int flags);
 extern int mpc8xxx_spi_probe(struct device *dev, struct resource *mem,
 		unsigned int irq);

drivers/spi/spi-fsl-spi.c

@@ -431,7 +431,7 @@ static int fsl_spi_setup(struct spi_device *spi)
 		return -EINVAL;
 
 	if (!cs) {
-		cs = kzalloc(sizeof *cs, GFP_KERNEL);
+		cs = devm_kzalloc(&spi->dev, sizeof(*cs), GFP_KERNEL);
 		if (!cs)
 			return -ENOMEM;
 		spi->controller_state = cs;

drivers/spi/spi-gpio.c

@@ -340,7 +340,7 @@ static int spi_gpio_request(struct spi_gpio_platform_data *pdata,
 }
 
 #ifdef CONFIG_OF
-static struct of_device_id spi_gpio_dt_ids[] = {
+static const struct of_device_id spi_gpio_dt_ids[] = {
 	{ .compatible = "spi-gpio" },
 	{}
 };

drivers/spi/spi-nuc900.c

@@ -10,7 +10,6 @@
 
 #include <linux/module.h>
 #include <linux/spinlock.h>
-#include <linux/workqueue.h>
 #include <linux/interrupt.h>
 #include <linux/delay.h>
 #include <linux/errno.h>

drivers/spi/spi-omap-uwire.c

@@ -37,7 +37,6 @@
 #include <linux/init.h>
 #include <linux/delay.h>
 #include <linux/platform_device.h>
-#include <linux/workqueue.h>
 #include <linux/interrupt.h>
 #include <linux/err.h>
 #include <linux/clk.h>

drivers/spi/spi-pl022.c

@@ -1111,10 +1111,8 @@ static int pl022_dma_probe(struct pl022 *pl022)
 	}
 
 	pl022->dummypage = kmalloc(PAGE_SIZE, GFP_KERNEL);
-	if (!pl022->dummypage) {
-		dev_dbg(&pl022->adev->dev, "no DMA dummypage!\n");
+	if (!pl022->dummypage)
 		goto err_no_dummypage;
-	}
 
 	dev_info(&pl022->adev->dev, "setup for DMA on RX %s, TX %s\n",
 		 dma_chan_name(pl022->dma_rx_channel),
@@ -1809,11 +1807,8 @@ static int pl022_setup(struct spi_device *spi)
 
 	if (chip == NULL) {
 		chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL);
-		if (!chip) {
-			dev_err(&spi->dev,
-				"cannot allocate controller state\n");
+		if (!chip)
 			return -ENOMEM;
-		}
 		dev_dbg(&spi->dev,
 			"allocated memory for controller's runtime state\n");
 	}
@@ -2050,10 +2045,8 @@ pl022_platform_data_dt_get(struct device *dev)
 	}
 
 	pd = devm_kzalloc(dev, sizeof(struct pl022_ssp_controller), GFP_KERNEL);
-	if (!pd) {
-		dev_err(dev, "cannot allocate platform data memory\n");
+	if (!pd)
 		return NULL;
-	}
 
 	pd->bus_id = -1;
 	pd->enable_dma = 1;

drivers/spi/spi-pxa2xx-pci.c

@@ -8,7 +8,43 @@
 #include <linux/module.h>
 #include <linux/spi/pxa2xx_spi.h>
 
-static int ce4100_spi_probe(struct pci_dev *dev,
+enum {
+	PORT_CE4100,
+	PORT_BYT,
+};
+
+struct pxa_spi_info {
+	enum pxa_ssp_type type;
+	int port_id;
+	int num_chipselect;
+	int tx_slave_id;
+	int tx_chan_id;
+	int rx_slave_id;
+	int rx_chan_id;
+};
+
+static struct pxa_spi_info spi_info_configs[] = {
+	[PORT_CE4100] = {
+		.type = PXA25x_SSP,
+		.port_id =  -1,
+		.num_chipselect = -1,
+		.tx_slave_id = -1,
+		.tx_chan_id = -1,
+		.rx_slave_id = -1,
+		.rx_chan_id = -1,
+	},
+	[PORT_BYT] = {
+		.type = LPSS_SSP,
+		.port_id = 0,
+		.num_chipselect = 1,
+		.tx_slave_id = 0,
+		.tx_chan_id = 0,
+		.rx_slave_id = 1,
+		.rx_chan_id = 1,
+	},
+};
+
+static int pxa2xx_spi_pci_probe(struct pci_dev *dev,
 		const struct pci_device_id *ent)
 {
 	struct platform_device_info pi;
@@ -16,6 +52,7 @@ static int ce4100_spi_probe(struct pci_dev *dev,
 	struct platform_device *pdev;
 	struct pxa2xx_spi_master spi_pdata;
 	struct ssp_device *ssp;
+	struct pxa_spi_info *c;
 
 	ret = pcim_enable_device(dev);
 	if (ret)
@@ -25,8 +62,16 @@ static int ce4100_spi_probe(struct pci_dev *dev,
 	if (ret)
 		return ret;
 
+	c = &spi_info_configs[ent->driver_data];
+
 	memset(&spi_pdata, 0, sizeof(spi_pdata));
-	spi_pdata.num_chipselect = dev->devfn;
+	spi_pdata.num_chipselect = (c->num_chipselect > 0) ?
+					c->num_chipselect : dev->devfn;
+	spi_pdata.tx_slave_id = c->tx_slave_id;
+	spi_pdata.tx_chan_id = c->tx_chan_id;
+	spi_pdata.rx_slave_id = c->rx_slave_id;
+	spi_pdata.rx_chan_id = c->rx_chan_id;
+	spi_pdata.enable_dma = c->rx_slave_id >= 0 && c->tx_slave_id >= 0;
 
 	ssp = &spi_pdata.ssp;
 	ssp->phys_base = pci_resource_start(dev, 0);
@@ -36,8 +81,8 @@ static int ce4100_spi_probe(struct pci_dev *dev,
 		return -EIO;
 	}
 	ssp->irq = dev->irq;
-	ssp->port_id = dev->devfn;
-	ssp->type = PXA25x_SSP;
+	ssp->port_id = (c->port_id >= 0) ? c->port_id : dev->devfn;
+	ssp->type = c->type;
 
 	memset(&pi, 0, sizeof(pi));
 	pi.parent = &dev->dev;
@@ -55,28 +100,29 @@ static int ce4100_spi_probe(struct pci_dev *dev,
 	return 0;
 }
 
-static void ce4100_spi_remove(struct pci_dev *dev)
+static void pxa2xx_spi_pci_remove(struct pci_dev *dev)
 {
 	struct platform_device *pdev = pci_get_drvdata(dev);
 
 	platform_device_unregister(pdev);
 }
 
-static const struct pci_device_id ce4100_spi_devices[] = {
-	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x2e6a) },
+static const struct pci_device_id pxa2xx_spi_pci_devices[] = {
+	{ PCI_VDEVICE(INTEL, 0x2e6a), PORT_CE4100 },
+	{ PCI_VDEVICE(INTEL, 0x0f0e), PORT_BYT },
 	{ },
 };
-MODULE_DEVICE_TABLE(pci, ce4100_spi_devices);
+MODULE_DEVICE_TABLE(pci, pxa2xx_spi_pci_devices);
 
-static struct pci_driver ce4100_spi_driver = {
-	.name           = "ce4100_spi",
-	.id_table       = ce4100_spi_devices,
-	.probe          = ce4100_spi_probe,
-	.remove         = ce4100_spi_remove,
+static struct pci_driver pxa2xx_spi_pci_driver = {
+	.name           = "pxa2xx_spi_pci",
+	.id_table       = pxa2xx_spi_pci_devices,
+	.probe          = pxa2xx_spi_pci_probe,
+	.remove         = pxa2xx_spi_pci_remove,
 };
 
-module_pci_driver(ce4100_spi_driver);
+module_pci_driver(pxa2xx_spi_pci_driver);
 
-MODULE_DESCRIPTION("CE4100 PCI-SPI glue code for PXA's driver");
+MODULE_DESCRIPTION("CE4100/LPSS PCI-SPI glue code for PXA's driver");
 MODULE_LICENSE("GPL v2");
 MODULE_AUTHOR("Sebastian Andrzej Siewior <bigeasy@linutronix.de>");

drivers/spi/spi-pxa2xx.c

@@ -27,7 +27,6 @@
 #include <linux/platform_device.h>
 #include <linux/spi/pxa2xx_spi.h>
 #include <linux/spi/spi.h>
-#include <linux/workqueue.h>
 #include <linux/delay.h>
 #include <linux/gpio.h>
 #include <linux/slab.h>
@@ -886,11 +885,8 @@ static int setup(struct spi_device *spi)
 	chip = spi_get_ctldata(spi);
 	if (!chip) {
 		chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL);
-		if (!chip) {
-			dev_err(&spi->dev,
-				"failed setup: can't allocate chip data\n");
+		if (!chip)
 			return -ENOMEM;
-		}
 
 		if (drv_data->ssp_type == CE4100_SSP) {
 			if (spi->chip_select > 4) {
@@ -1037,11 +1033,8 @@ pxa2xx_spi_acpi_get_pdata(struct platform_device *pdev)
 		return NULL;
 
 	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
-	if (!pdata) {
-		dev_err(&pdev->dev,
-			"failed to allocate memory for platform data\n");
+	if (!pdata)
 		return NULL;
-	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!res)
@@ -1202,6 +1195,11 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 	tasklet_init(&drv_data->pump_transfers, pump_transfers,
 		     (unsigned long)drv_data);
 
+	pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
+	pm_runtime_use_autosuspend(&pdev->dev);
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+
 	/* Register with the SPI framework */
 	platform_set_drvdata(pdev, drv_data);
 	status = devm_spi_register_master(&pdev->dev, master);
@@ -1210,11 +1208,6 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 		goto out_error_clock_enabled;
 	}
 
-	pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
-	pm_runtime_use_autosuspend(&pdev->dev);
-	pm_runtime_set_active(&pdev->dev);
-	pm_runtime_enable(&pdev->dev);
-
 	return status;
 
 out_error_clock_enabled:

drivers/spi/spi-qup.c

@@ -287,7 +287,7 @@ static irqreturn_t spi_qup_qup_irq(int irq, void *dev_id)
 	writel_relaxed(opflags, controller->base + QUP_OPERATIONAL);
 
 	if (!xfer) {
-		dev_err_ratelimited(controller->dev, "unexpected irq %x08 %x08 %x08\n",
+		dev_err_ratelimited(controller->dev, "unexpected irq %08x %08x %08x\n",
 				    qup_err, spi_err, opflags);
 		return IRQ_HANDLED;
 	}
@@ -366,7 +366,7 @@ static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
 	n_words = xfer->len / w_size;
 	controller->w_size = w_size;
 
-	if (n_words <= controller->in_fifo_sz) {
+	if (n_words <= (controller->in_fifo_sz / sizeof(u32))) {
 		mode = QUP_IO_M_MODE_FIFO;
 		writel_relaxed(n_words, controller->base + QUP_MX_READ_CNT);
 		writel_relaxed(n_words, controller->base + QUP_MX_WRITE_CNT);
@@ -749,7 +749,7 @@ static int spi_qup_remove(struct platform_device *pdev)
 	return 0;
 }
 
-static struct of_device_id spi_qup_dt_match[] = {
+static const struct of_device_id spi_qup_dt_match[] = {
 	{ .compatible = "qcom,spi-qup-v2.1.1", },
 	{ .compatible = "qcom,spi-qup-v2.2.1", },
 	{ }

drivers/spi/spi-s3c24xx.c

@@ -10,7 +10,6 @@
 */
 
 #include <linux/spinlock.h>
-#include <linux/workqueue.h>
 #include <linux/interrupt.h>
 #include <linux/delay.h>
 #include <linux/errno.h>
@@ -183,11 +182,11 @@ static int s3c24xx_spi_setup(struct spi_device *spi)
 
 	/* allocate settings on the first call */
 	if (!cs) {
-		cs = kzalloc(sizeof(struct s3c24xx_spi_devstate), GFP_KERNEL);
-		if (!cs) {
-			dev_err(&spi->dev, "no memory for controller state\n");
+		cs = devm_kzalloc(&spi->dev,
+				  sizeof(struct s3c24xx_spi_devstate),
+				  GFP_KERNEL);
+		if (!cs)
 			return -ENOMEM;
-		}
 
 		cs->spcon = SPCON_DEFAULT;
 		cs->hz = -1;
@@ -209,11 +208,6 @@ static int s3c24xx_spi_setup(struct spi_device *spi)
 	return 0;
 }
 
-static void s3c24xx_spi_cleanup(struct spi_device *spi)
-{
-	kfree(spi->controller_state);
-}
-
 static inline unsigned int hw_txbyte(struct s3c24xx_spi *hw, int count)
 {
 	return hw->tx ? hw->tx[count] : 0;
@@ -543,7 +537,6 @@ static int s3c24xx_spi_probe(struct platform_device *pdev)
 	hw->bitbang.txrx_bufs      = s3c24xx_spi_txrx;
 
 	hw->master->setup  = s3c24xx_spi_setup;
-	hw->master->cleanup = s3c24xx_spi_cleanup;
 
 	dev_dbg(hw->dev, "bitbang at %p\n", &hw->bitbang);
 

drivers/spi/spi-s3c64xx.c

@@ -19,7 +19,6 @@
 
 #include <linux/init.h>
 #include <linux/module.h>
-#include <linux/workqueue.h>
 #include <linux/interrupt.h>
 #include <linux/delay.h>
 #include <linux/clk.h>
@@ -773,7 +772,6 @@ static struct s3c64xx_spi_csinfo *s3c64xx_get_slave_ctrldata(
 
 	cs = kzalloc(sizeof(*cs), GFP_KERNEL);
 	if (!cs) {
-		dev_err(&spi->dev, "could not allocate memory for controller data\n");
 		of_node_put(data_np);
 		return ERR_PTR(-ENOMEM);
 	}
@@ -987,10 +985,8 @@ static struct s3c64xx_spi_info *s3c64xx_spi_parse_dt(struct device *dev)
 	u32 temp;
 
 	sci = devm_kzalloc(dev, sizeof(*sci), GFP_KERNEL);
-	if (!sci) {
-		dev_err(dev, "memory allocation for spi_info failed\n");
+	if (!sci)
 		return ERR_PTR(-ENOMEM);
-	}
 
 	if (of_property_read_u32(dev->of_node, "samsung,spi-src-clk", &temp)) {
 		dev_warn(dev, "spi bus clock parent not specified, using clock at index 0 as parent\n");

drivers/spi/spi-sh-msiof.c

@@ -642,10 +642,8 @@ static struct sh_msiof_spi_info *sh_msiof_spi_parse_dt(struct device *dev)
 	u32 num_cs = 1;
 
 	info = devm_kzalloc(dev, sizeof(struct sh_msiof_spi_info), GFP_KERNEL);
-	if (!info) {
-		dev_err(dev, "failed to allocate setup data\n");
+	if (!info)
 		return NULL;
-	}
 
 	/* Parse the MSIOF properties */
 	of_property_read_u32(np, "num-cs", &num_cs);

drivers/spi/spi-sh-sci.c

@@ -16,7 +16,6 @@
 #include <linux/kernel.h>
 #include <linux/delay.h>
 #include <linux/spinlock.h>
-#include <linux/workqueue.h>
 #include <linux/platform_device.h>
 
 #include <linux/spi/spi.h>

drivers/spi/spi-sirf.c

@@ -10,6 +10,7 @@
 #include <linux/kernel.h>
 #include <linux/slab.h>
 #include <linux/clk.h>
+#include <linux/completion.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/of.h>
@@ -85,6 +86,7 @@
 #define SIRFSOC_SPI_TX_DONE		BIT(1)
 #define SIRFSOC_SPI_RX_OFLOW		BIT(2)
 #define SIRFSOC_SPI_TX_UFLOW		BIT(3)
+#define SIRFSOC_SPI_RX_IO_DMA		BIT(4)
 #define SIRFSOC_SPI_RX_FIFO_FULL	BIT(6)
 #define SIRFSOC_SPI_TXFIFO_EMPTY	BIT(7)
 #define SIRFSOC_SPI_RXFIFO_THD_REACH	BIT(8)
@@ -264,41 +266,34 @@ static irqreturn_t spi_sirfsoc_irq(int irq, void *dev_id)
 {
 	struct sirfsoc_spi *sspi = dev_id;
 	u32 spi_stat = readl(sspi->base + SIRFSOC_SPI_INT_STATUS);
-
-	writel(spi_stat, sspi->base + SIRFSOC_SPI_INT_STATUS);
-
 	if (sspi->tx_by_cmd && (spi_stat & SIRFSOC_SPI_FRM_END)) {
 		complete(&sspi->tx_done);
 		writel(0x0, sspi->base + SIRFSOC_SPI_INT_EN);
+		writel(SIRFSOC_SPI_INT_MASK_ALL,
+				sspi->base + SIRFSOC_SPI_INT_STATUS);
 		return IRQ_HANDLED;
 	}
 
 	/* Error Conditions */
 	if (spi_stat & SIRFSOC_SPI_RX_OFLOW ||
 			spi_stat & SIRFSOC_SPI_TX_UFLOW) {
+		complete(&sspi->tx_done);
 		complete(&sspi->rx_done);
 		writel(0x0, sspi->base + SIRFSOC_SPI_INT_EN);
+		writel(SIRFSOC_SPI_INT_MASK_ALL,
+				sspi->base + SIRFSOC_SPI_INT_STATUS);
+		return IRQ_HANDLED;
 	}
+	if (spi_stat & SIRFSOC_SPI_TXFIFO_EMPTY)
+		complete(&sspi->tx_done);
+	while (!(readl(sspi->base + SIRFSOC_SPI_INT_STATUS) &
+		SIRFSOC_SPI_RX_IO_DMA))
+		cpu_relax();
+	complete(&sspi->rx_done);
+	writel(0x0, sspi->base + SIRFSOC_SPI_INT_EN);
+	writel(SIRFSOC_SPI_INT_MASK_ALL,
+			sspi->base + SIRFSOC_SPI_INT_STATUS);
 
-	if (spi_stat & (SIRFSOC_SPI_FRM_END
-			| SIRFSOC_SPI_RXFIFO_THD_REACH))
-		while (!((readl(sspi->base + SIRFSOC_SPI_RXFIFO_STATUS)
-				& SIRFSOC_SPI_FIFO_EMPTY)) &&
-				sspi->left_rx_word)
-			sspi->rx_word(sspi);
-
-	if (spi_stat & (SIRFSOC_SPI_TXFIFO_EMPTY |
-			SIRFSOC_SPI_TXFIFO_THD_REACH))
-		while (!((readl(sspi->base + SIRFSOC_SPI_TXFIFO_STATUS)
-				& SIRFSOC_SPI_FIFO_FULL)) &&
-				sspi->left_tx_word)
-			sspi->tx_word(sspi);
-
-	/* Received all words */
-	if ((sspi->left_rx_word == 0) && (sspi->left_tx_word == 0)) {
-		complete(&sspi->rx_done);
-		writel(0x0, sspi->base + SIRFSOC_SPI_INT_EN);
-	}
 	return IRQ_HANDLED;
 }
 
@@ -309,59 +304,51 @@ static void spi_sirfsoc_dma_fini_callback(void *data)
 	complete(dma_complete);
 }
 
-static int spi_sirfsoc_transfer(struct spi_device *spi, struct spi_transfer *t)
+static int spi_sirfsoc_cmd_transfer(struct spi_device *spi,
+	struct spi_transfer *t)
 {
 	struct sirfsoc_spi *sspi;
 	int timeout = t->len * 10;
-	sspi = spi_master_get_devdata(spi->master);
+	u32 cmd;
 
-	sspi->tx = t->tx_buf ? t->tx_buf : sspi->dummypage;
-	sspi->rx = t->rx_buf ? t->rx_buf : sspi->dummypage;
-	sspi->left_tx_word = sspi->left_rx_word = t->len / sspi->word_width;
-	reinit_completion(&sspi->rx_done);
-	reinit_completion(&sspi->tx_done);
-
-	writel(SIRFSOC_SPI_INT_MASK_ALL, sspi->base + SIRFSOC_SPI_INT_STATUS);
-
-	/*
-	 * fill tx_buf into command register and wait for its completion
-	 */
-	if (sspi->tx_by_cmd) {
-		u32 cmd;
-		memcpy(&cmd, sspi->tx, t->len);
-
-		if (sspi->word_width == 1 && !(spi->mode & SPI_LSB_FIRST))
-			cmd = cpu_to_be32(cmd) >>
-				((SIRFSOC_MAX_CMD_BYTES - t->len) * 8);
-		if (sspi->word_width == 2 && t->len == 4 &&
-				(!(spi->mode & SPI_LSB_FIRST)))
-			cmd = ((cmd & 0xffff) << 16) | (cmd >> 16);
-
-		writel(cmd, sspi->base + SIRFSOC_SPI_CMD);
-		writel(SIRFSOC_SPI_FRM_END_INT_EN,
-			sspi->base + SIRFSOC_SPI_INT_EN);
-		writel(SIRFSOC_SPI_CMD_TX_EN,
-			sspi->base + SIRFSOC_SPI_TX_RX_EN);
+	sspi = spi_master_get_devdata(spi->master);
+	memcpy(&cmd, sspi->tx, t->len);
+	if (sspi->word_width == 1 && !(spi->mode & SPI_LSB_FIRST))
+		cmd = cpu_to_be32(cmd) >>
+			((SIRFSOC_MAX_CMD_BYTES - t->len) * 8);
+	if (sspi->word_width == 2 && t->len == 4 &&
+			(!(spi->mode & SPI_LSB_FIRST)))
+		cmd = ((cmd & 0xffff) << 16) | (cmd >> 16);
+	writel(cmd, sspi->base + SIRFSOC_SPI_CMD);
+	writel(SIRFSOC_SPI_FRM_END_INT_EN,
+		sspi->base + SIRFSOC_SPI_INT_EN);
+	writel(SIRFSOC_SPI_CMD_TX_EN,
+		sspi->base + SIRFSOC_SPI_TX_RX_EN);
+	if (wait_for_completion_timeout(&sspi->tx_done, timeout) == 0) {
+		dev_err(&spi->dev, "cmd transfer timeout\n");
+		return 0;
+	}
 
-		if (wait_for_completion_timeout(&sspi->tx_done, timeout) == 0) {
-			dev_err(&spi->dev, "transfer timeout\n");
-			return 0;
-		}
+	return t->len;
+}
 
-		return t->len;
-	}
+static void spi_sirfsoc_dma_transfer(struct spi_device *spi,
+	struct spi_transfer *t)
+{
+	struct sirfsoc_spi *sspi;
+	struct dma_async_tx_descriptor *rx_desc, *tx_desc;
+	int timeout = t->len * 10;
 
-	if (sspi->left_tx_word == 1) {
-		writel(readl(sspi->base + SIRFSOC_SPI_CTRL) |
-			SIRFSOC_SPI_ENA_AUTO_CLR,
-			sspi->base + SIRFSOC_SPI_CTRL);
-		writel(0, sspi->base + SIRFSOC_SPI_TX_DMA_IO_LEN);
-		writel(0, sspi->base + SIRFSOC_SPI_RX_DMA_IO_LEN);
-	} else if ((sspi->left_tx_word > 1) && (sspi->left_tx_word <
-				SIRFSOC_SPI_DAT_FRM_LEN_MAX)) {
+	sspi = spi_master_get_devdata(spi->master);
+	writel(SIRFSOC_SPI_FIFO_RESET, sspi->base + SIRFSOC_SPI_RXFIFO_OP);
+	writel(SIRFSOC_SPI_FIFO_RESET, sspi->base + SIRFSOC_SPI_TXFIFO_OP);
+	writel(SIRFSOC_SPI_FIFO_START, sspi->base + SIRFSOC_SPI_RXFIFO_OP);
+	writel(SIRFSOC_SPI_FIFO_START, sspi->base + SIRFSOC_SPI_TXFIFO_OP);
+	writel(0, sspi->base + SIRFSOC_SPI_INT_EN);
+	writel(SIRFSOC_SPI_INT_MASK_ALL, sspi->base + SIRFSOC_SPI_INT_STATUS);
+	if (sspi->left_tx_word < SIRFSOC_SPI_DAT_FRM_LEN_MAX) {
 		writel(readl(sspi->base + SIRFSOC_SPI_CTRL) |
-				SIRFSOC_SPI_MUL_DAT_MODE |
-				SIRFSOC_SPI_ENA_AUTO_CLR,
+			SIRFSOC_SPI_ENA_AUTO_CLR | SIRFSOC_SPI_MUL_DAT_MODE,
 			sspi->base + SIRFSOC_SPI_CTRL);
 		writel(sspi->left_tx_word - 1,
 				sspi->base + SIRFSOC_SPI_TX_DMA_IO_LEN);
@@ -373,76 +360,122 @@ static int spi_sirfsoc_transfer(struct spi_device *spi, struct spi_transfer *t)
 		writel(0, sspi->base + SIRFSOC_SPI_TX_DMA_IO_LEN);
 		writel(0, sspi->base + SIRFSOC_SPI_RX_DMA_IO_LEN);
 	}
-
-	writel(SIRFSOC_SPI_FIFO_RESET, sspi->base + SIRFSOC_SPI_RXFIFO_OP);
-	writel(SIRFSOC_SPI_FIFO_RESET, sspi->base + SIRFSOC_SPI_TXFIFO_OP);
-	writel(SIRFSOC_SPI_FIFO_START, sspi->base + SIRFSOC_SPI_RXFIFO_OP);
-	writel(SIRFSOC_SPI_FIFO_START, sspi->base + SIRFSOC_SPI_TXFIFO_OP);
-
-	if (IS_DMA_VALID(t)) {
-		struct dma_async_tx_descriptor *rx_desc, *tx_desc;
-
-		sspi->dst_start = dma_map_single(&spi->dev, sspi->rx, t->len, DMA_FROM_DEVICE);
-		rx_desc = dmaengine_prep_slave_single(sspi->rx_chan,
-			sspi->dst_start, t->len, DMA_DEV_TO_MEM,
-			DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
-		rx_desc->callback = spi_sirfsoc_dma_fini_callback;
-		rx_desc->callback_param = &sspi->rx_done;
-
-		sspi->src_start = dma_map_single(&spi->dev, (void *)sspi->tx, t->len, DMA_TO_DEVICE);
-		tx_desc = dmaengine_prep_slave_single(sspi->tx_chan,
-			sspi->src_start, t->len, DMA_MEM_TO_DEV,
-			DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
-		tx_desc->callback = spi_sirfsoc_dma_fini_callback;
-		tx_desc->callback_param = &sspi->tx_done;
-
-		dmaengine_submit(tx_desc);
-		dmaengine_submit(rx_desc);
-		dma_async_issue_pending(sspi->tx_chan);
-		dma_async_issue_pending(sspi->rx_chan);
-	} else {
-		/* Send the first word to trigger the whole tx/rx process */
-		sspi->tx_word(sspi);
-
-		writel(SIRFSOC_SPI_RX_OFLOW_INT_EN | SIRFSOC_SPI_TX_UFLOW_INT_EN |
-			SIRFSOC_SPI_RXFIFO_THD_INT_EN | SIRFSOC_SPI_TXFIFO_THD_INT_EN |
-			SIRFSOC_SPI_FRM_END_INT_EN | SIRFSOC_SPI_RXFIFO_FULL_INT_EN |
-			SIRFSOC_SPI_TXFIFO_EMPTY_INT_EN, sspi->base + SIRFSOC_SPI_INT_EN);
-	}
-
-	writel(SIRFSOC_SPI_RX_EN | SIRFSOC_SPI_TX_EN, sspi->base + SIRFSOC_SPI_TX_RX_EN);
-
-	if (!IS_DMA_VALID(t)) { /* for PIO */
-		if (wait_for_completion_timeout(&sspi->rx_done, timeout) == 0)
-			dev_err(&spi->dev, "transfer timeout\n");
-	} else if (wait_for_completion_timeout(&sspi->rx_done, timeout) == 0) {
+	sspi->dst_start = dma_map_single(&spi->dev, sspi->rx, t->len,
+					(t->tx_buf != t->rx_buf) ?
+					DMA_FROM_DEVICE : DMA_BIDIRECTIONAL);
+	rx_desc = dmaengine_prep_slave_single(sspi->rx_chan,
+		sspi->dst_start, t->len, DMA_DEV_TO_MEM,
+		DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+	rx_desc->callback = spi_sirfsoc_dma_fini_callback;
+	rx_desc->callback_param = &sspi->rx_done;
+
+	sspi->src_start = dma_map_single(&spi->dev, (void *)sspi->tx, t->len,
+					(t->tx_buf != t->rx_buf) ?
+					DMA_TO_DEVICE : DMA_BIDIRECTIONAL);
+	tx_desc = dmaengine_prep_slave_single(sspi->tx_chan,
+		sspi->src_start, t->len, DMA_MEM_TO_DEV,
+		DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+	tx_desc->callback = spi_sirfsoc_dma_fini_callback;
+	tx_desc->callback_param = &sspi->tx_done;
+
+	dmaengine_submit(tx_desc);
+	dmaengine_submit(rx_desc);
+	dma_async_issue_pending(sspi->tx_chan);
+	dma_async_issue_pending(sspi->rx_chan);
+	writel(SIRFSOC_SPI_RX_EN | SIRFSOC_SPI_TX_EN,
+			sspi->base + SIRFSOC_SPI_TX_RX_EN);
+	if (wait_for_completion_timeout(&sspi->rx_done, timeout) == 0) {
 		dev_err(&spi->dev, "transfer timeout\n");
 		dmaengine_terminate_all(sspi->rx_chan);
 	} else
 		sspi->left_rx_word = 0;
-
 	/*
 	 * we only wait tx-done event if transferring by DMA. for PIO,
 	 * we get rx data by writing tx data, so if rx is done, tx has
 	 * done earlier
 	 */
-	if (IS_DMA_VALID(t)) {
-		if (wait_for_completion_timeout(&sspi->tx_done, timeout) == 0) {
-			dev_err(&spi->dev, "transfer timeout\n");
-			dmaengine_terminate_all(sspi->tx_chan);
-		}
-	}
-
-	if (IS_DMA_VALID(t)) {
-		dma_unmap_single(&spi->dev, sspi->src_start, t->len, DMA_TO_DEVICE);
-		dma_unmap_single(&spi->dev, sspi->dst_start, t->len, DMA_FROM_DEVICE);
+	if (wait_for_completion_timeout(&sspi->tx_done, timeout) == 0) {
+		dev_err(&spi->dev, "transfer timeout\n");
+		dmaengine_terminate_all(sspi->tx_chan);
 	}
-
+	dma_unmap_single(&spi->dev, sspi->src_start, t->len, DMA_TO_DEVICE);
+	dma_unmap_single(&spi->dev, sspi->dst_start, t->len, DMA_FROM_DEVICE);
 	/* TX, RX FIFO stop */
 	writel(0, sspi->base + SIRFSOC_SPI_RXFIFO_OP);
 	writel(0, sspi->base + SIRFSOC_SPI_TXFIFO_OP);
-	writel(0, sspi->base + SIRFSOC_SPI_TX_RX_EN);
-	writel(0, sspi->base + SIRFSOC_SPI_INT_EN);
+	if (sspi->left_tx_word >= SIRFSOC_SPI_DAT_FRM_LEN_MAX)
+		writel(0, sspi->base + SIRFSOC_SPI_TX_RX_EN);
+}
+
+static void spi_sirfsoc_pio_transfer(struct spi_device *spi,
+		struct spi_transfer *t)
+{
+	struct sirfsoc_spi *sspi;
+	int timeout = t->len * 10;
+
+	sspi = spi_master_get_devdata(spi->master);
+	do {
+		writel(SIRFSOC_SPI_FIFO_RESET,
+			sspi->base + SIRFSOC_SPI_RXFIFO_OP);
+		writel(SIRFSOC_SPI_FIFO_RESET,
+			sspi->base + SIRFSOC_SPI_TXFIFO_OP);
+		writel(SIRFSOC_SPI_FIFO_START,
+			sspi->base + SIRFSOC_SPI_RXFIFO_OP);
+		writel(SIRFSOC_SPI_FIFO_START,
+			sspi->base + SIRFSOC_SPI_TXFIFO_OP);
+		writel(0, sspi->base + SIRFSOC_SPI_INT_EN);
+		writel(SIRFSOC_SPI_INT_MASK_ALL,
+			sspi->base + SIRFSOC_SPI_INT_STATUS);
+		writel(readl(sspi->base + SIRFSOC_SPI_CTRL) |
+			SIRFSOC_SPI_MUL_DAT_MODE | SIRFSOC_SPI_ENA_AUTO_CLR,
+			sspi->base + SIRFSOC_SPI_CTRL);
+		writel(min(sspi->left_tx_word, (u32)(256 / sspi->word_width))
+				- 1, sspi->base + SIRFSOC_SPI_TX_DMA_IO_LEN);
+		writel(min(sspi->left_rx_word, (u32)(256 / sspi->word_width))
+				- 1, sspi->base + SIRFSOC_SPI_RX_DMA_IO_LEN);
+		while (!((readl(sspi->base + SIRFSOC_SPI_TXFIFO_STATUS)
+			& SIRFSOC_SPI_FIFO_FULL)) && sspi->left_tx_word)
+			sspi->tx_word(sspi);
+		writel(SIRFSOC_SPI_TXFIFO_EMPTY_INT_EN |
+			SIRFSOC_SPI_TX_UFLOW_INT_EN |
+			SIRFSOC_SPI_RX_OFLOW_INT_EN,
+			sspi->base + SIRFSOC_SPI_INT_EN);
+		writel(SIRFSOC_SPI_RX_EN | SIRFSOC_SPI_TX_EN,
+			sspi->base + SIRFSOC_SPI_TX_RX_EN);
+		if (!wait_for_completion_timeout(&sspi->tx_done, timeout) ||
+			!wait_for_completion_timeout(&sspi->rx_done, timeout)) {
+			dev_err(&spi->dev, "transfer timeout\n");
+			break;
+		}
+		while (!((readl(sspi->base + SIRFSOC_SPI_RXFIFO_STATUS)
+			& SIRFSOC_SPI_FIFO_EMPTY)) && sspi->left_rx_word)
+			sspi->rx_word(sspi);
+		writel(0, sspi->base + SIRFSOC_SPI_RXFIFO_OP);
+		writel(0, sspi->base + SIRFSOC_SPI_TXFIFO_OP);
+	} while (sspi->left_tx_word != 0 || sspi->left_rx_word != 0);
+}
+
+static int spi_sirfsoc_transfer(struct spi_device *spi, struct spi_transfer *t)
+{
+	struct sirfsoc_spi *sspi;
+	sspi = spi_master_get_devdata(spi->master);
+
+	sspi->tx = t->tx_buf ? t->tx_buf : sspi->dummypage;
+	sspi->rx = t->rx_buf ? t->rx_buf : sspi->dummypage;
+	sspi->left_tx_word = sspi->left_rx_word = t->len / sspi->word_width;
+	reinit_completion(&sspi->rx_done);
+	reinit_completion(&sspi->tx_done);
+	/*
+	 * in the transfer, if transfer data using command register with rx_buf
+	 * null, just fill command data into command register and wait for its
+	 * completion.
+	 */
+	if (sspi->tx_by_cmd)
+		spi_sirfsoc_cmd_transfer(spi, t);
+	else if (IS_DMA_VALID(t))
+		spi_sirfsoc_dma_transfer(spi, t);
+	else
+		spi_sirfsoc_pio_transfer(spi, t);
 
 	return t->len - sspi->left_rx_word * sspi->word_width;
 }
@@ -512,7 +545,8 @@ spi_sirfsoc_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
 		break;
 	case 12:
 	case 16:
-		regval |= (bits_per_word ==  12) ? SIRFSOC_SPI_TRAN_DAT_FORMAT_12 :
+		regval |= (bits_per_word ==  12) ?
+			SIRFSOC_SPI_TRAN_DAT_FORMAT_12 :
 			SIRFSOC_SPI_TRAN_DAT_FORMAT_16;
 		sspi->rx_word = spi_sirfsoc_rx_word_u16;
 		sspi->tx_word = spi_sirfsoc_tx_word_u16;
@@ -540,8 +574,8 @@ spi_sirfsoc_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
 		regval |= SIRFSOC_SPI_CLK_IDLE_STAT;
 
 	/*
-	 * Data should be driven at least 1/2 cycle before the fetch edge to make
-	 * sure that data gets stable at the fetch edge.
+	 * Data should be driven at least 1/2 cycle before the fetch edge
+	 * to make sure that data gets stable at the fetch edge.
 	 */
 	if (((spi->mode & SPI_CPOL) && (spi->mode & SPI_CPHA)) ||
 	    (!(spi->mode & SPI_CPOL) && !(spi->mode & SPI_CPHA)))
@@ -578,11 +612,14 @@ spi_sirfsoc_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
 	if (IS_DMA_VALID(t)) {
 		/* Enable DMA mode for RX, TX */
 		writel(0, sspi->base + SIRFSOC_SPI_TX_DMA_IO_CTRL);
-		writel(SIRFSOC_SPI_RX_DMA_FLUSH, sspi->base + SIRFSOC_SPI_RX_DMA_IO_CTRL);
+		writel(SIRFSOC_SPI_RX_DMA_FLUSH,
+			sspi->base + SIRFSOC_SPI_RX_DMA_IO_CTRL);
 	} else {
 		/* Enable IO mode for RX, TX */
-		writel(SIRFSOC_SPI_IO_MODE_SEL, sspi->base + SIRFSOC_SPI_TX_DMA_IO_CTRL);
-		writel(SIRFSOC_SPI_IO_MODE_SEL, sspi->base + SIRFSOC_SPI_RX_DMA_IO_CTRL);
+		writel(SIRFSOC_SPI_IO_MODE_SEL,
+			sspi->base + SIRFSOC_SPI_TX_DMA_IO_CTRL);
+		writel(SIRFSOC_SPI_IO_MODE_SEL,
+			sspi->base + SIRFSOC_SPI_RX_DMA_IO_CTRL);
 	}
 
 	return 0;
@@ -612,7 +649,8 @@ static int spi_sirfsoc_probe(struct platform_device *pdev)
 		goto err_cs;
 	}
 
-	master = spi_alloc_master(&pdev->dev, sizeof(*sspi) + sizeof(int) * num_cs);
+	master = spi_alloc_master(&pdev->dev,
+			sizeof(*sspi) + sizeof(int) * num_cs);
 	if (!master) {
 		dev_err(&pdev->dev, "Unable to allocate SPI master\n");
 		return -ENOMEM;
@@ -808,8 +846,7 @@ static struct platform_driver spi_sirfsoc_driver = {
 	.remove = spi_sirfsoc_remove,
 };
 module_platform_driver(spi_sirfsoc_driver);
-
 MODULE_DESCRIPTION("SiRF SoC SPI master driver");
-MODULE_AUTHOR("Zhiwu Song <Zhiwu.Song@csr.com>, "
-		"Barry Song <Baohua.Song@csr.com>");
+MODULE_AUTHOR("Zhiwu Song <Zhiwu.Song@csr.com>");
+MODULE_AUTHOR("Barry Song <Baohua.Song@csr.com>");
 MODULE_LICENSE("GPL v2");

drivers/spi/spi-sun4i.c

@@ -19,7 +19,6 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
-#include <linux/workqueue.h>
 
 #include <linux/spi/spi.h>
 

drivers/spi/spi-sun6i.c

@@ -20,7 +20,6 @@
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/reset.h>
-#include <linux/workqueue.h>
 
 #include <linux/spi/spi.h>
 

drivers/spi/spi-tegra114.c

@@ -1012,7 +1012,7 @@ static irqreturn_t tegra_spi_isr(int irq, void *context_data)
 	return IRQ_WAKE_THREAD;
 }
 
-static struct of_device_id tegra_spi_of_match[] = {
+static const struct of_device_id tegra_spi_of_match[] = {
 	{ .compatible = "nvidia,tegra114-spi", },
 	{}
 };

drivers/spi/spi-tegra20-sflash.c

@@ -419,7 +419,7 @@ static irqreturn_t tegra_sflash_isr(int irq, void *context_data)
 	return handle_cpu_based_xfer(tsd);
 }
 
-static struct of_device_id tegra_sflash_of_match[] = {
+static const struct of_device_id tegra_sflash_of_match[] = {
 	{ .compatible = "nvidia,tegra20-sflash", },
 	{}
 };

drivers/spi/spi-tegra20-slink.c

@@ -1001,7 +1001,7 @@ static const struct tegra_slink_chip_data tegra20_spi_cdata = {
 	.cs_hold_time = false,
 };
 
-static struct of_device_id tegra_slink_of_match[] = {
+static const struct of_device_id tegra_slink_of_match[] = {
 	{ .compatible = "nvidia,tegra30-slink", .data = &tegra30_spi_cdata, },
 	{ .compatible = "nvidia,tegra20-slink", .data = &tegra20_spi_cdata, },
 	{}

drivers/spi/spi-tle62x0.c

@@ -253,10 +253,8 @@ static int tle62x0_probe(struct spi_device *spi)
 	}
 
 	st = kzalloc(sizeof(struct tle62x0_state), GFP_KERNEL);
-	if (st == NULL) {
-		dev_err(&spi->dev, "no memory for device state\n");
+	if (st == NULL)
 		return -ENOMEM;
-	}
 
 	st->us = spi;
 	st->nr_gpio = pdata->gpio_count;

drivers/spi/spi-topcliff-pch.c

@@ -1578,14 +1578,11 @@ static int pch_spi_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	struct pch_pd_dev_save *pd_dev_save;
 
 	pd_dev_save = kzalloc(sizeof(struct pch_pd_dev_save), GFP_KERNEL);
-	if (!pd_dev_save) {
-		dev_err(&pdev->dev, "%s Can't allocate pd_dev_sav\n", __func__);
+	if (!pd_dev_save)
 		return -ENOMEM;
-	}
 
 	board_dat = kzalloc(sizeof(struct pch_spi_board_data), GFP_KERNEL);
 	if (!board_dat) {
-		dev_err(&pdev->dev, "%s Can't allocate board_dat\n", __func__);
 		retval = -ENOMEM;
 		goto err_no_mem;
 	}

drivers/spi/spi.c

@@ -796,7 +796,7 @@ static int spi_transfer_one_message(struct spi_master *master,
 		if (ret > 0) {
 			ret = 0;
 			ms = xfer->len * 8 * 1000 / xfer->speed_hz;
-			ms += 10; /* some tolerance */
+			ms += ms + 100; /* some tolerance */
 
 			ms = wait_for_completion_timeout(&master->xfer_completion,
 							 msecs_to_jiffies(ms));
@@ -1255,6 +1255,8 @@ static void of_register_spi_devices(struct spi_master *master)
 			spi->mode |= SPI_CS_HIGH;
 		if (of_find_property(nc, "spi-3wire", NULL))
 			spi->mode |= SPI_3WIRE;
+		if (of_find_property(nc, "spi-lsb-first", NULL))
+			spi->mode |= SPI_LSB_FIRST;
 
 		/* Device DUAL/QUAD mode */
 		if (!of_property_read_u32(nc, "spi-tx-bus-width", &value)) {
@@ -1268,11 +1270,10 @@ static void of_register_spi_devices(struct spi_master *master)
 				spi->mode |= SPI_TX_QUAD;
 				break;
 			default:
-				dev_err(&master->dev,
-					"spi-tx-bus-width %d not supported\n",
-					value);
-				spi_dev_put(spi);
-				continue;
+				dev_warn(&master->dev,
+					 "spi-tx-bus-width %d not supported\n",
+					 value);
+				break;
 			}
 		}
 
@@ -1287,11 +1288,10 @@ static void of_register_spi_devices(struct spi_master *master)
 				spi->mode |= SPI_RX_QUAD;
 				break;
 			default:
-				dev_err(&master->dev,
-					"spi-rx-bus-width %d not supported\n",
-					value);
-				spi_dev_put(spi);
-				continue;
+				dev_warn(&master->dev,
+					 "spi-rx-bus-width %d not supported\n",
+					 value);
+				break;
 			}
 		}
 

arch/blackfin/include/asm/bfin_spi3.h → include/linux/spi/adi_spi3.h

 /*
  * Analog Devices SPI3 controller driver
  *
- * Copyright (c) 2011 Analog Devices Inc.
+ * Copyright (c) 2014 Analog Devices Inc.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -11,14 +11,10 @@
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  */
 
-#ifndef _SPI_CHANNEL_H_
-#define _SPI_CHANNEL_H_
+#ifndef _ADI_SPI3_H_
+#define _ADI_SPI3_H_
 
 #include <linux/types.h>
 
@@ -209,9 +205,9 @@
 #define SPI_ILAT_CLR_TFI            0x00000800    /* Transmit Finish Indication */
 
 /*
- * bfin spi3 registers layout
+ * adi spi3 registers layout
  */
-struct bfin_spi_regs {
+struct adi_spi_regs {
 	u32 revid;
 	u32 control;
 	u32 rx_control;
@@ -240,7 +236,7 @@ struct bfin_spi_regs {
 #define MAX_CTRL_CS          8  /* cs in spi controller */
 
 /* device.platform_data for SSP controller devices */
-struct bfin_spi3_master {
+struct adi_spi3_master {
 	u16 num_chipselect;
 	u16 pin_req[7];
 };
@@ -248,11 +244,11 @@ struct bfin_spi3_master {
 /* spi_board_info.controller_data for SPI slave devices,
  * copied to spi_device.platform_data ... mostly for dma tuning
  */
-struct bfin_spi3_chip {
+struct adi_spi3_chip {
 	u32 control;
 	u16 cs_chg_udelay; /* Some devices require 16-bit delays */
 	u32 tx_dummy_val; /* tx value for rx only transfer */
 	bool enable_dma;
 };
 
-#endif /* _SPI_CHANNEL_H_ */
+#endif /* _ADI_SPI3_H_ */

include/linux/spi/rspi.h

@@ -25,8 +25,6 @@ struct rspi_plat_data {
 	unsigned int dma_tx_id;
 	unsigned int dma_rx_id;
 
-	unsigned dma_width_16bit:1;	/* DMAC read/write width = 16-bit */
-
 	u16 num_chipselect;
 };