[POWERPC] 83xx: Add MPC837x USB platform support

Add chip specific and board specific initialization for MPC837x USB.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

arch/powerpc/platforms/83xx/mpc837x_mds.c

@@ -22,6 +22,56 @@
 
 #include "mpc83xx.h"
 
+#define BCSR12_USB_SER_MASK	0x8a
+#define BCSR12_USB_SER_PIN	0x80
+#define BCSR12_USB_SER_DEVICE	0x02
+extern int mpc837x_usb_cfg(void);
+
+static int mpc837xmds_usb_cfg(void)
+{
+	struct device_node *np;
+	const void *phy_type, *mode;
+	void __iomem *bcsr_regs = NULL;
+	u8 bcsr12;
+	int ret;
+
+	ret = mpc837x_usb_cfg();
+	if (ret)
+		return ret;
+	/* Map BCSR area */
+	np = of_find_node_by_name(NULL, "bcsr");
+	if (np) {
+		struct resource res;
+
+		of_address_to_resource(np, 0, &res);
+		bcsr_regs = ioremap(res.start, res.end - res.start + 1);
+		of_node_put(np);
+	}
+	if (!bcsr_regs)
+		return -1;
+
+	np = of_find_node_by_name(NULL, "usb");
+	if (!np)
+		return -ENODEV;
+	phy_type = of_get_property(np, "phy_type", NULL);
+	if (phy_type && !strcmp(phy_type, "ulpi")) {
+		clrbits8(bcsr_regs + 12, BCSR12_USB_SER_PIN);
+	} else if (phy_type && !strcmp(phy_type, "serial")) {
+		mode = of_get_property(np, "dr_mode", NULL);
+		bcsr12 = in_8(bcsr_regs + 12) & ~BCSR12_USB_SER_MASK;
+		bcsr12 |= BCSR12_USB_SER_PIN;
+		if (mode && !strcmp(mode, "peripheral"))
+			bcsr12 |= BCSR12_USB_SER_DEVICE;
+		out_8(bcsr_regs + 12, bcsr12);
+	} else {
+		printk(KERN_ERR "USB DR: unsupported PHY\n");
+	}
+
+	of_node_put(np);
+	iounmap(bcsr_regs);
+	return 0;
+}
+
 /* ************************************************************************
  *
  * Setup the architecture
@@ -40,6 +90,7 @@ static void __init mpc837x_mds_setup_arch(void)
 	for_each_compatible_node(np, "pci", "fsl,mpc8349-pci")
 		mpc83xx_add_bridge(np);
 #endif
+	mpc837xmds_usb_cfg();
 }
 
 static struct of_device_id mpc837x_ids[] = {

arch/powerpc/platforms/83xx/mpc83xx.h

@@ -14,6 +14,7 @@
 #define MPC83XX_SCCR_USB_DRCM_11   0x00300000
 #define MPC83XX_SCCR_USB_DRCM_01   0x00100000
 #define MPC83XX_SCCR_USB_DRCM_10   0x00200000
+#define MPC837X_SCCR_USB_DRCM_11   0x00c00000
 
 /* system i/o configuration register low */
 #define MPC83XX_SICRL_OFFS         0x114
@@ -22,6 +23,8 @@
 #define MPC834X_SICRL_USB1         0x20000000
 #define MPC831X_SICRL_USB_MASK     0x00000c00
 #define MPC831X_SICRL_USB_ULPI     0x00000800
+#define MPC837X_SICRL_USB_MASK     0xf0000000
+#define MPC837X_SICRL_USB_ULPI     0x50000000
 
 /* system i/o configuration register high */
 #define MPC83XX_SICRH_OFFS         0x118

arch/powerpc/platforms/83xx/usb.c

@@ -179,3 +179,43 @@ int mpc831x_usb_cfg(void)
 	return ret;
 }
 #endif /* CONFIG_PPC_MPC831x */
+
+#ifdef CONFIG_PPC_MPC837x
+int mpc837x_usb_cfg(void)
+{
+	void __iomem *immap;
+	struct device_node *np = NULL;
+	const void *prop;
+	int ret = 0;
+
+	np = of_find_compatible_node(NULL, "usb", "fsl-usb2-dr");
+	if (!np)
+		return -ENODEV;
+	prop = of_get_property(np, "phy_type", NULL);
+
+	if (!prop || (strcmp(prop, "ulpi") && strcmp(prop, "serial"))) {
+		printk(KERN_WARNING "837x USB PHY type not supported\n");
+		of_node_put(np);
+		return -EINVAL;
+	}
+
+	/* Map IMMR space for pin and clock settings */
+	immap = ioremap(get_immrbase(), 0x1000);
+	if (!immap) {
+		of_node_put(np);
+		return -ENOMEM;
+	}
+
+	/* Configure clock */
+	clrsetbits_be32(immap + MPC83XX_SCCR_OFFS, MPC837X_SCCR_USB_DRCM_11,
+			MPC837X_SCCR_USB_DRCM_11);
+
+	/* Configure pin mux for ULPI/serial */
+	clrsetbits_be32(immap + MPC83XX_SICRL_OFFS, MPC837X_SICRL_USB_MASK,
+			MPC837X_SICRL_USB_ULPI);
+
+	iounmap(immap);
+	of_node_put(np);
+	return ret;
+}
+#endif /* CONFIG_PPC_MPC837x */