mtd: nand: Request strength instead of bytes for soft BCH

Previously, we requested that drivers pass ecc.size and ecc.bytes when
using NAND_ECC_SOFT_BCH. However, a driver is likely to only know the ECC
strength required for its NAND, so each driver would need to perform a
strength-to-bytes calculation.

Avoid duplicating this calculation in each driver by asking drivers to
pass ecc.size and ecc.strength so that the strength-to-bytes calculation
need only be implemented once.

This reverts/generalizes this commit:
    mtd: nand: Base BCH ECC bytes on required strength
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

drivers/mtd/nand/nand_base.c

@@ -4037,22 +4037,24 @@ int nand_scan_tail(struct mtd_info *mtd)
 		ecc->read_oob = nand_read_oob_std;
 		ecc->write_oob = nand_write_oob_std;
 		/*
-		 * Board driver should supply ecc.size and ecc.bytes values to
-		 * select how many bits are correctable; see nand_bch_init()
-		 * for details. Otherwise, default to 4 bits for large page
-		 * devices.
+		 * Board driver should supply ecc.size and ecc.strength values
+		 * to select how many bits are correctable. Otherwise, default
+		 * to 4 bits for large page devices.
 		 */
 		if (!ecc->size && (mtd->oobsize >= 64)) {
 			ecc->size = 512;
-			ecc->bytes = DIV_ROUND_UP(13 * ecc->strength, 8);
+			ecc->strength = 4;
 		}
+
+		/* See nand_bch_init() for details. */
+		ecc->bytes = DIV_ROUND_UP(
+				ecc->strength * fls(8 * ecc->size), 8);
 		ecc->priv = nand_bch_init(mtd, ecc->size, ecc->bytes,
 					       &ecc->layout);
 		if (!ecc->priv) {
 			pr_warn("BCH ECC initialization failed!\n");
 			BUG();
 		}
-		ecc->strength = ecc->bytes * 8 / fls(8 * ecc->size);
 		break;
 
 	case NAND_ECC_NONE:

drivers/mtd/nand/nandsim.c

@@ -2337,6 +2337,7 @@ static int __init ns_init_module(void)
 		}
 		chip->ecc.mode = NAND_ECC_SOFT_BCH;
 		chip->ecc.size = 512;
+		chip->ecc.strength = bch;
 		chip->ecc.bytes = eccbytes;
 		NS_INFO("using %u-bit/%u bytes BCH ECC\n", bch, chip->ecc.size);
 	}

drivers/mtd/nand/sunxi_nand.c

@@ -1110,8 +1110,6 @@ static int sunxi_nand_ecc_init(struct mtd_info *mtd, struct nand_ecc_ctrl *ecc,
 
 	switch (ecc->mode) {
 	case NAND_ECC_SOFT_BCH:
-		ecc->bytes = DIV_ROUND_UP(ecc->strength * fls(8 * ecc->size),
-					  8);
 		break;
 	case NAND_ECC_HW:
 		ret = sunxi_nand_hw_ecc_ctrl_init(mtd, ecc, np);