Davinci: generalized debug macros

This patch adopts a debug uart selection similar to the OMAP model.  During
the boot process, the uncompress code determines the physical and virtual base
addresses of the board-specific debug uart.  These addresses are then passed
on to the in-kernel debug macros through a small chunk of memory placed just
below the page tables (@0x80003ff8).
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

arch/arm/mach-davinci/include/mach/debug-macro.S

@@ -17,22 +17,50 @@
  */
 
 #include <linux/serial_reg.h>
+
+#include <asm/memory.h>
+
+#include <mach/serial.h>
+
 #define UART_SHIFT	2
 
+		.pushsection .data
+davinci_uart_phys:	.word	0
+davinci_uart_virt:	.word	0
+		.popsection
+
 		.macro addruart, rx, tmp
+
+		/* Use davinci_uart_phys/virt if already configured */
+10:		mrc	p15, 0, \rx, c1, c0
+		tst	\rx, #1			@ MMU enabled?
+		ldreq	\rx, =__virt_to_phys(davinci_uart_phys)
+		ldrne	\rx, =davinci_uart_virt
+		ldr	\rx, [\rx]
+		cmp	\rx, #0			@ is port configured?
+		bne	99f			@ already configured
+
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1			@ MMU enabled?
-		moveq	\rx, #0x01000000	@ physical base address
-		movne	\rx, #0xfe000000	@ virtual base
-#if defined(CONFIG_ARCH_DAVINCI_DA8XX) && defined(CONFIG_ARCH_DAVINCI_DMx)
-#error Cannot enable DaVinci and DA8XX platforms concurrently
-#elif defined(CONFIG_MACH_DAVINCI_DA830_EVM) || \
-	defined(CONFIG_MACH_DAVINCI_DA850_EVM)
-		orr	\rx, \rx, #0x00d00000	@ physical base address
-		orr	\rx, \rx, #0x0000d000	@ of UART 2
-#else
-		orr	\rx, \rx, #0x00c20000   @ UART 0
-#endif
+
+		/* Copy uart phys address from decompressor uart info */
+		ldreq	\tmp, =__virt_to_phys(davinci_uart_phys)
+		ldrne	\tmp, =davinci_uart_phys
+		ldreq	\rx, =DAVINCI_UART_INFO
+		ldrne	\rx, =__phys_to_virt(DAVINCI_UART_INFO)
+		ldr	\rx, [\rx, #0]
+		str	\rx, [\tmp]
+
+		/* Copy uart virt address from decompressor uart info */
+		ldreq	\tmp, =__virt_to_phys(davinci_uart_virt)
+		ldrne	\tmp, =davinci_uart_virt
+		ldreq	\rx, =DAVINCI_UART_INFO
+		ldrne	\rx, =__phys_to_virt(DAVINCI_UART_INFO)
+		ldr	\rx, [\rx, #4]
+		str	\rx, [\tmp]
+
+		b	10b
+99:
 		.endm
 
 		.macro	senduart,rd,rx

arch/arm/mach-davinci/include/mach/serial.h

@@ -11,8 +11,19 @@
 #ifndef __ASM_ARCH_SERIAL_H
 #define __ASM_ARCH_SERIAL_H
 
+#include <asm/memory.h>
+
 #include <mach/hardware.h>
 
+/*
+ * Stolen area that contains debug uart physical and virtual addresses.  These
+ * addresses are filled in by the uncompress.h code, and are used by the debug
+ * macros in debug-macro.S.
+ *
+ * This area sits just below the page tables (see arch/arm/kernel/head.S).
+ */
+#define DAVINCI_UART_INFO	(PHYS_OFFSET + 0x3ff8)
+
 #define DAVINCI_UART0_BASE	(IO_PHYS + 0x20000)
 #define DAVINCI_UART1_BASE	(IO_PHYS + 0x20400)
 #define DAVINCI_UART2_BASE	(IO_PHYS + 0x20800)
@@ -26,11 +37,13 @@
 #define UART_DM646X_SCR			0x10
 #define UART_DM646X_SCR_TX_WATERMARK	0x08
 
+#ifndef __ASSEMBLY__
 struct davinci_uart_config {
 	/* Bit field of UARTs present; bit 0 --> UART1 */
 	unsigned int enabled_uarts;
 };
 
 extern int davinci_serial_init(struct davinci_uart_config *);
+#endif
 
 #endif /* __ASM_ARCH_SERIAL_H */

arch/arm/mach-davinci/include/mach/uncompress.h

 /*
  * Serial port stubs for kernel decompress status messages
  *
- *  Author:     Anant Gole
- * (C) Copyright (C) 2006, Texas Instruments, Inc
+ * Initially based on:
+ * arch/arm/plat-omap/include/mach/uncompress.h
+ *
+ * Original copyrights follow.
+ *
+ * Copyright (C) 2000 RidgeRun, Inc.
+ * Author: Greg Lonnon <glonnon@ridgerun.com>
+ *
+ * Rewritten by:
+ * Author: <source@mvista.com>
+ * 2004 (c) MontaVista Software, Inc.
  *
  * This file is licensed under the terms of the GNU General Public License
  * version 2. This program is licensed "as is" without any warranty of any
@@ -11,30 +20,17 @@
 
 #include <linux/types.h>
 #include <linux/serial_reg.h>
-#include <mach/serial.h>
 
 #include <asm/mach-types.h>
 
-extern unsigned int __machine_arch_type;
+#include <mach/serial.h>
 
 static u32 *uart;
-
-static u32 *get_uart_base(void)
-{
-	if (__machine_arch_type == MACH_TYPE_DAVINCI_DA830_EVM ||
-		__machine_arch_type == MACH_TYPE_DAVINCI_DA850_EVM)
-		return (u32 *)DA8XX_UART2_BASE;
-	else
-		return (u32 *)DAVINCI_UART0_BASE;
-}
+static u32 *uart_info = (u32 *)(DAVINCI_UART_INFO);
 
 /* PORT_16C550A, in polled non-fifo mode */
-
 static void putc(char c)
 {
-	if (!uart)
-		uart = get_uart_base();
-
 	while (!(uart[UART_LSR] & UART_LSR_THRE))
 		barrier();
 	uart[UART_TX] = c;
@@ -42,12 +38,54 @@ static void putc(char c)
 
 static inline void flush(void)
 {
-	if (!uart)
-		uart = get_uart_base();
-
 	while (!(uart[UART_LSR] & UART_LSR_THRE))
 		barrier();
 }
 
-#define arch_decomp_setup()
+static inline void set_uart_info(u32 phys, void * __iomem virt)
+{
+	uart = (u32 *)phys;
+	uart_info[0] = phys;
+	uart_info[1] = (u32)virt;
+}
+
+#define _DEBUG_LL_ENTRY(machine, phys, virt)			\
+	if (machine_is_##machine()) {				\
+		set_uart_info(phys, virt);			\
+		break;						\
+	}
+
+#define DEBUG_LL_DAVINCI(machine, port)				\
+	_DEBUG_LL_ENTRY(machine, DAVINCI_UART##port##_BASE,	\
+			IO_ADDRESS(DAVINCI_UART##port##_BASE))
+
+#define DEBUG_LL_DA8XX(machine, port)				\
+	_DEBUG_LL_ENTRY(machine, DA8XX_UART##port##_BASE,	\
+			IO_ADDRESS(DA8XX_UART##port##_BASE))
+
+static inline void __arch_decomp_setup(unsigned long arch_id)
+{
+	/*
+	 * Initialize the port based on the machine ID from the bootloader.
+	 * Note that we're using macros here instead of switch statement
+	 * as machine_is functions are optimized out for the boards that
+	 * are not selected.
+	 */
+	do {
+		/* Davinci boards */
+		DEBUG_LL_DAVINCI(davinci_evm,		0);
+		DEBUG_LL_DAVINCI(sffsdr,		0);
+		DEBUG_LL_DAVINCI(neuros_osd2,		0);
+		DEBUG_LL_DAVINCI(davinci_dm355_evm,	0);
+		DEBUG_LL_DAVINCI(dm355_leopard,		0);
+		DEBUG_LL_DAVINCI(davinci_dm6467_evm,	0);
+		DEBUG_LL_DAVINCI(davinci_dm365_evm,	0);
+
+		/* DA8xx boards */
+		DEBUG_LL_DA8XX(davinci_da830_evm,	2);
+		DEBUG_LL_DA8XX(davinci_da850_evm,	2);
+	} while (0);
+}
+
+#define arch_decomp_setup()	__arch_decomp_setup(arch_id)
 #define arch_decomp_wdog()