UBI: add max_beb_per1024 to attach ioctl

This patch provides a possibility to set the "maximum expected number of
bad blocks per 1024 blocks" (max_beb_per1024) for each mtd device using
the UBI_IOCATT ioctl.
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

drivers/mtd/ubi/Kconfig

@@ -51,7 +51,8 @@ config MTD_UBI_BEB_LIMIT
 	  MTD partitions of the same size, UBI will reserve 40 eraseblocks when
 	  attaching a partition.
 
-	  This option can be overridden by the "mtd=" UBI module parameter.
+	  This option can be overridden by the "mtd=" UBI module parameter or
+	  by the "attach" ioctl.
 
 	  Leave the default value if unsure.
 

drivers/mtd/ubi/cdev.c

@@ -1011,7 +1011,7 @@ static long ctrl_cdev_ioctl(struct file *file, unsigned int cmd,
 		 */
 		mutex_lock(&ubi_devices_mutex);
 		err = ubi_attach_mtd_dev(mtd, req.ubi_num, req.vid_hdr_offset,
-					 CONFIG_MTD_UBI_BEB_LIMIT);
+					 req.max_beb_per1024);
 		mutex_unlock(&ubi_devices_mutex);
 		if (err < 0)
 			put_mtd_device(mtd);

include/mtd/ubi-user.h

@@ -222,6 +222,7 @@ enum {
  * @ubi_num: UBI device number to create
  * @mtd_num: MTD device number to attach
  * @vid_hdr_offset: VID header offset (use defaults if %0)
+ * @max_beb_per1024: maximum expected number of bad PEB per 1024 PEBs
  * @padding: reserved for future, not used, has to be zeroed
  *
  * This data structure is used to specify MTD device UBI has to attach and the
@@ -245,12 +246,25 @@ enum {
  * be 2KiB-64 bytes = 1984. Note, that this position is not even 512-bytes
  * aligned, which is OK, as UBI is clever enough to realize this is 4th
  * sub-page of the first page and add needed padding.
+ *
+ * The @max_beb_per1024 is the maximum amount of bad PEBs UBI expects on the
+ * UBI device per 1024 eraseblocks.  This value is often given in an other form
+ * in the NAND datasheet (min NVB i.e. minimal number of valid blocks). The
+ * maximum expected bad eraseblocks per 1024 is then:
+ *    1024 * (1 - MinNVB / MaxNVB)
+ * Which gives 20 for most NAND devices.  This limit is used in order to derive
+ * amount of eraseblock UBI reserves for handling new bad blocks. If the device
+ * has more bad eraseblocks than this limit, UBI does not reserve any physical
+ * eraseblocks for new bad eraseblocks, but attempts to use available
+ * eraseblocks (if any). The accepted range is 0-768. If 0 is given, the
+ * default kernel value of %CONFIG_MTD_UBI_BEB_LIMIT will be used.
  */
 struct ubi_attach_req {
 	__s32 ubi_num;
 	__s32 mtd_num;
 	__s32 vid_hdr_offset;
-	__s8 padding[12];
+	__s16 max_beb_per1024;
+	__s8 padding[10];
 };
 
 /**