ARM: S3C24XX: trim down debug uart handling

Using the lowlevel debug uart is a corner case - even more so in a
multiplatform environment. So it seems reasonable to simply let the
developer set the appropriate uart type for the debugged SoC.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

arch/arm/Kconfig.debug

@@ -670,6 +670,33 @@ choice
 		  The uncompressor code port configuration is now handled
 		  by CONFIG_S3C_LOWLEVEL_UART_PORT.
 
+	config DEBUG_S3C2410_UART0
+		depends on ARCH_S3C24XX
+		select DEBUG_S3C2410_UART
+		bool "Use S3C2410/S3C2412 UART 0 for low-level debug"
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to UART 0. The port must have been initialised
+		  by the boot-loader before use.
+
+	config DEBUG_S3C2410_UART1
+		depends on ARCH_S3C24XX
+		select DEBUG_S3C2410_UART
+		bool "Use S3C2410/S3C2412 UART 1 for low-level debug"
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to UART 1. The port must have been initialised
+		  by the boot-loader before use.
+
+	config DEBUG_S3C2410_UART2
+		depends on ARCH_S3C24XX
+		select DEBUG_S3C2410_UART
+		bool "Use S3C2410/S3C2412 UART 2 for low-level debug"
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to UART 2. The port must have been initialised
+		  by the boot-loader before use.
+
 	config DEBUG_SOCFPGA_UART
 		depends on ARCH_SOCFPGA
 		bool "Use SOCFPGA UART for low-level debug"
@@ -921,6 +948,9 @@ endchoice
 config DEBUG_EXYNOS_UART
 	bool
 
+config DEBUG_S3C2410_UART
+	bool
+
 config DEBUG_OMAP2PLUS_UART
 	bool
 	depends on ARCH_OMAP2PLUS

arch/arm/mach-s3c24xx/Kconfig

@@ -39,7 +39,6 @@ config CPU_S3C2410
 	default y
 	select COMMON_CLK
 	select CPU_ARM920T
-	select CPU_LLSERIAL_S3C2410
 	select S3C2410_COMMON_CLK
 	select S3C2410_DMA if S3C24XX_DMA
 	select ARM_S3C2410_CPUFREQ if ARM_S3C24XX_CPUFREQ
@@ -53,7 +52,6 @@ config CPU_S3C2412
 	bool "SAMSUNG S3C2412"
 	select COMMON_CLK
 	select CPU_ARM926T
-	select CPU_LLSERIAL_S3C2440
 	select S3C2412_COMMON_CLK
 	select S3C2412_DMA if S3C24XX_DMA
 	select S3C2412_PM if PM
@@ -64,7 +62,6 @@ config CPU_S3C2416
 	bool "SAMSUNG S3C2416/S3C2450"
 	select COMMON_CLK
 	select CPU_ARM926T
-	select CPU_LLSERIAL_S3C2440
 	select S3C2416_PM if PM
 	select S3C2443_COMMON_CLK
 	select S3C2443_DMA if S3C24XX_DMA
@@ -75,7 +72,6 @@ config CPU_S3C2440
 	bool "SAMSUNG S3C2440"
 	select COMMON_CLK
 	select CPU_ARM920T
-	select CPU_LLSERIAL_S3C2440
 	select S3C2410_COMMON_CLK
 	select S3C2410_PM if PM
 	select S3C2440_DMA if S3C24XX_DMA
@@ -86,7 +82,6 @@ config CPU_S3C2442
 	bool "SAMSUNG S3C2442"
 	select COMMON_CLK
 	select CPU_ARM920T
-	select CPU_LLSERIAL_S3C2440
 	select S3C2410_COMMON_CLK
 	select S3C2410_DMA if S3C24XX_DMA
 	select S3C2410_PM if PM
@@ -102,7 +97,6 @@ config CPU_S3C2443
 	bool "SAMSUNG S3C2443"
 	select COMMON_CLK
 	select CPU_ARM920T
-	select CPU_LLSERIAL_S3C2440
 	select S3C2443_COMMON_CLK
 	select S3C2443_DMA if S3C24XX_DMA
 	help
@@ -164,28 +158,6 @@ config S3C2410_PM
 	help
 	  Power Management code common to S3C2410 and better
 
-# low-level serial option nodes
-
-config CPU_LLSERIAL_S3C2410_ONLY
-	bool
-	default y if CPU_LLSERIAL_S3C2410 && !CPU_LLSERIAL_S3C2440
-
-config CPU_LLSERIAL_S3C2440_ONLY
-	bool
-	default y if CPU_LLSERIAL_S3C2440 && !CPU_LLSERIAL_S3C2410
-
-config CPU_LLSERIAL_S3C2410
-	bool
-	help
-	  Selected if there is an S3C2410 (or register compatible) serial
-	  low-level implementation needed
-
-config CPU_LLSERIAL_S3C2440
-	bool
-	help
-	  Selected if there is an S3C2440 (or register compatible) serial
-	  low-level implementation needed
-
 config S3C24XX_PLL
 	bool "Support CPUfreq changing of PLL frequency (EXPERIMENTAL)"
 	depends on ARM_S3C24XX_CPUFREQ

arch/arm/mach-s3c24xx/include/mach/debug-macro.S

@@ -13,11 +13,9 @@
 */
 
 #include <mach/map.h>
-#include <mach/regs-gpio.h>
 #include <linux/serial_s3c.h>
 
 #define S3C2410_UART1_OFF (0x4000)
-#define SHIFT_2440TXF (14-9)
 
 	.macro addruart, rp, rv, tmp
 		ldr	\rp, = S3C24XX_PA_UART
@@ -28,56 +26,11 @@
 #endif
 	.endm
 
-	.macro fifo_full_s3c24xx rd, rx
-		@ check for arm920 vs arm926. currently assume all arm926
-		@ devices have an 64 byte FIFO identical to the s3c2440
-		mrc	p15, 0, \rd, c0, c0
-		and	\rd, \rd, #0xff0
-		teq	\rd, #0x260
-		beq	1004f
-		mrc	p15, 0, \rd, c1, c0
-		tst	\rd, #1
-		addeq	\rd, \rx, #(S3C24XX_PA_GPIO - S3C24XX_PA_UART)
-		addne	\rd, \rx, #(S3C24XX_VA_GPIO - S3C24XX_VA_UART)
-		bic	\rd, \rd, #0xff000
-		ldr	\rd, [\rd, # S3C2410_GSTATUS1 - S3C2410_GPIOREG(0)]
-		and	\rd, \rd, #0x00ff0000
-		teq	\rd, #0x00440000		@ is it 2440?
-1004:
-		ldr	\rd, [\rx, # S3C2410_UFSTAT]
-		moveq	\rd, \rd, lsr #SHIFT_2440TXF
-		tst	\rd, #S3C2410_UFSTAT_TXFULL
-	.endm
-
 	.macro  fifo_full_s3c2410 rd, rx
 		ldr	\rd, [\rx, # S3C2410_UFSTAT]
 		tst	\rd, #S3C2410_UFSTAT_TXFULL
 	.endm
 
-/* fifo level reading */
-
-	.macro fifo_level_s3c24xx rd, rx
-		@ check for arm920 vs arm926. currently assume all arm926
-		@ devices have an 64 byte FIFO identical to the s3c2440
-		mrc	p15, 0, \rd, c0, c0
-		and	\rd, \rd, #0xff0
-		teq	\rd, #0x260
-		beq	10000f
-		mrc	p15, 0, \rd, c1, c0
-		tst	\rd, #1
-		addeq	\rd, \rx, #(S3C24XX_PA_GPIO - S3C24XX_PA_UART)
-		addne	\rd, \rx, #(S3C24XX_VA_GPIO - S3C24XX_VA_UART)
-		bic	\rd, \rd, #0xff000
-		ldr	\rd, [\rd, # S3C2410_GSTATUS1 - S3C2410_GPIOREG(0)]
-		and	\rd, \rd, #0x00ff0000
-		teq	\rd, #0x00440000		@ is it 2440?
-
-10000:
-		ldr	\rd, [\rx, # S3C2410_UFSTAT]
-		andne	\rd, \rd, #S3C2410_UFSTAT_TXMASK
-		andeq	\rd, \rd, #S3C2440_UFSTAT_TXMASK
-	.endm
-
 	.macro fifo_level_s3c2410 rd, rx
 		ldr	\rd, [\rx, # S3C2410_UFSTAT]
 		and	\rd, \rd, #S3C2410_UFSTAT_TXMASK
@@ -88,12 +41,9 @@
  * used variants of these
 */
 
-#if defined(CONFIG_CPU_LLSERIAL_S3C2410_ONLY)
+#if defined(CONFIG_DEBUG_S3C2410_UART)
 #define fifo_full  fifo_full_s3c2410
 #define fifo_level fifo_level_s3c2410
-#elif !defined(CONFIG_CPU_LLSERIAL_S3C2440_ONLY)
-#define fifo_full  fifo_full_s3c24xx
-#define fifo_level fifo_level_s3c24xx
 #endif
 
 /* include the reset of the code which will do the work */