提交 d532dbe2 编写于 作者: B bo yang 提交者: James Bottomley

[SCSI] megaraid_sas: Fix the frame count calculation

When Driver sent wrong frame count to firmware.  As this particular
command is sent to drive, FW is seeing continuous chip resets and so
the command will timeout.

Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
上级 b70a41e0
......@@ -488,12 +488,13 @@ megasas_make_sgl64(struct megasas_instance *instance, struct scsi_cmnd *scp,
/**
* megasas_get_frame_count - Computes the number of frames
* @frame_type : type of frame- io or pthru frame
* @sge_count : number of sg elements
*
* Returns the number of frames required for numnber of sge's (sge_count)
*/
static u32 megasas_get_frame_count(u8 sge_count)
static u32 megasas_get_frame_count(u8 sge_count, u8 frame_type)
{
int num_cnt;
int sge_bytes;
......@@ -504,13 +505,22 @@ static u32 megasas_get_frame_count(u8 sge_count)
sizeof(struct megasas_sge32);
/*
* Main frame can contain 2 SGEs for 64-bit SGLs and
* 3 SGEs for 32-bit SGLs
*/
if (IS_DMA64)
num_cnt = sge_count - 2;
else
num_cnt = sge_count - 3;
* Main frame can contain 2 SGEs for 64-bit SGLs and
* 3 SGEs for 32-bit SGLs for ldio &
* 1 SGEs for 64-bit SGLs and
* 2 SGEs for 32-bit SGLs for pthru frame
*/
if (unlikely(frame_type == PTHRU_FRAME)) {
if (IS_DMA64)
num_cnt = sge_count - 1;
else
num_cnt = sge_count - 2;
} else {
if (IS_DMA64)
num_cnt = sge_count - 2;
else
num_cnt = sge_count - 3;
}
if(num_cnt>0){
sge_bytes = sge_sz * num_cnt;
......@@ -592,7 +602,8 @@ megasas_build_dcdb(struct megasas_instance *instance, struct scsi_cmnd *scp,
* Compute the total number of frames this command consumes. FW uses
* this number to pull sufficient number of frames from host memory.
*/
cmd->frame_count = megasas_get_frame_count(pthru->sge_count);
cmd->frame_count = megasas_get_frame_count(pthru->sge_count,
PTHRU_FRAME);
return cmd->frame_count;
}
......@@ -709,7 +720,7 @@ megasas_build_ldio(struct megasas_instance *instance, struct scsi_cmnd *scp,
* Compute the total number of frames this command consumes. FW uses
* this number to pull sufficient number of frames from host memory.
*/
cmd->frame_count = megasas_get_frame_count(ldio->sge_count);
cmd->frame_count = megasas_get_frame_count(ldio->sge_count, IO_FRAME);
return cmd->frame_count;
}
......
......@@ -542,6 +542,10 @@ struct megasas_ctrl_info {
#define MEGASAS_FW_BUSY 1
/* Frame Type */
#define IO_FRAME 0
#define PTHRU_FRAME 1
/*
* When SCSI mid-layer calls driver's reset routine, driver waits for
* MEGASAS_RESET_WAIT_TIME seconds for all outstanding IO to complete. Note
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册