Merge branch 'drm-next-analogix-dp-v2' of github.com:yakir-Yang/linux into drm-next

This pull request want to land the analogix_dp driver into drm/bridge directory,
which reused the Exynos DP code, and add Rockchip DP support. And those
patches have been:

* 'drm-next-analogix-dp-v2' of github.com:yakir-Yang/linux:
  drm: bridge: analogix/dp: Fix the possible dead lock in bridge disable time
  drm: bridge: analogix/dp: add panel prepare/unprepare in suspend/resume time
  drm: bridge: analogix/dp: add edid modes parse in get_modes method
  drm: bridge: analogix/dp: move hpd detect to connector detect function
  drm: bridge: analogix/dp: try force hpd after plug in lookup failed
  drm: bridge: analogix/dp: add max link rate and lane count limit for RK3288
  drm: bridge: analogix/dp: add some rk3288 special registers setting
  dt-bindings: add document for rockchip variant of analogix_dp
  drm: rockchip: dp: add rockchip platform dp driver
  ARM: dts: exynos/dp: remove some properties that deprecated by analogix_dp driver
  dt-bindings: add document for analogix display port driver
  drm: bridge: analogix/dp: dynamic parse sync_pol & interlace & dynamic_range
  drm: bridge: analogix/dp: remove duplicate configuration of link rate and link count
  drm: bridge: analogix/dp: fix some obvious code style
  drm: bridge: analogix/dp: rename register constants
  drm/exynos: dp: rename implementation specific driver part
  drm: bridge: analogix/dp: split exynos dp driver to bridge directory

Documentation/devicetree/bindings/display/bridge/analogix_dp.txt

+Analogix Display Port bridge bindings
+
+Required properties for dp-controller:
+	-compatible:
+		platform specific such as:
+		 * "samsung,exynos5-dp"
+		 * "rockchip,rk3288-dp"
+	-reg:
+		physical base address of the controller and length
+		of memory mapped region.
+	-interrupts:
+		interrupt combiner values.
+	-clocks:
+		from common clock binding: handle to dp clock.
+	-clock-names:
+		from common clock binding: Shall be "dp".
+	-interrupt-parent:
+		phandle to Interrupt combiner node.
+	-phys:
+		from general PHY binding: the phandle for the PHY device.
+	-phy-names:
+		from general PHY binding: Should be "dp".
+
+Optional properties for dp-controller:
+	-force-hpd:
+		Indicate driver need force hpd when hpd detect failed, this
+		is used for some eDP screen which don't have hpd signal.
+	-hpd-gpios:
+		Hotplug detect GPIO.
+		Indicates which GPIO should be used for hotplug detection
+	-port@[X]: SoC specific port nodes with endpoint definitions as defined
+		in Documentation/devicetree/bindings/media/video-interfaces.txt,
+		please refer to the SoC specific binding document:
+		* Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
+		* Documentation/devicetree/bindings/video/analogix_dp-rockchip.txt
+
+[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
+-------------------------------------------------------------------------------
+
+Example:
+
+	dp-controller {
+		compatible = "samsung,exynos5-dp";
+		reg = <0x145b0000 0x10000>;
+		interrupts = <10 3>;
+		interrupt-parent = <&combiner>;
+		clocks = <&clock 342>;
+		clock-names = "dp";
+
+		phys = <&dp_phy>;
+		phy-names = "dp";
+	};

Documentation/devicetree/bindings/display/exynos/exynos_dp.txt

-Device-Tree bindings for Samsung Exynos Embedded DisplayPort Transmitter(eDP)
-
-DisplayPort is industry standard to accommodate the growing board adoption
-of digital display technology within the PC and CE industries.
-It consolidates the internal and external connection methods to reduce device
-complexity and cost. It also supports necessary features for important cross
-industry applications and provides performance scalability to enable the next
-generation of displays that feature higher color depths, refresh rates, and
-display resolutions.
-
-eDP (embedded display port) device is compliant with Embedded DisplayPort
-standard as follows,
-- DisplayPort standard 1.1a for Exynos5250 and Exynos5260.
-- DisplayPort standard 1.3 for Exynos5422s and Exynos5800.
-
-eDP resides between FIMD and panel or FIMD and bridge such as LVDS.
-
 The Exynos display port interface should be configured based on
 the type of panel connected to it.
 
@@ -48,26 +31,6 @@ Required properties for dp-controller:
 		from general PHY binding: the phandle for the PHY device.
 	-phy-names:
 		from general PHY binding: Should be "dp".
-	-samsung,color-space:
-		input video data format.
-			COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2
-	-samsung,dynamic-range:
-		dynamic range for input video data.
-			VESA = 0, CEA = 1
-	-samsung,ycbcr-coeff:
-		YCbCr co-efficients for input video.
-			COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1
-	-samsung,color-depth:
-		number of bits per colour component.
-			COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3
-	-samsung,link-rate:
-		link rate supported by the panel.
-			LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A
-	-samsung,lane-count:
-		number of lanes supported by the panel.
-			LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4
-	- display-timings: timings for the connected panel as described by
-		Documentation/devicetree/bindings/display/display-timing.txt
 
 Optional properties for dp-controller:
 	-interlaced:
@@ -83,17 +46,31 @@ Optional properties for dp-controller:
 		Hotplug detect GPIO.
 			Indicates which GPIO should be used for hotplug
 			detection
-Video interfaces:
-  Device node can contain video interface port nodes according to [1].
-  The following are properties specific to those nodes:
-
-  endpoint node connected to bridge or panel node:
-   - remote-endpoint: specifies the endpoint in panel or bridge node.
-		      This node is required in all kinds of exynos dp
-		      to represent the connection between dp and bridge
-		      or dp and panel.
-
-[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
+	-video interfaces: Device node can contain video interface port
+			nodes according to [1].
+	- display-timings: timings for the connected panel as described by
+		Documentation/devicetree/bindings/display/panel/display-timing.txt
+
+For the below properties, please refer to Analogix DP binding document:
+ * Documentation/devicetree/bindings/display/bridge/analogix_dp.txt
+	-phys (required)
+	-phy-names (required)
+	-hpd-gpios (optional)
+	 force-hpd (optional)
+
+Deprecated properties for DisplayPort:
+-interlaced:            deprecated prop that can parsed from drm_display_mode.
+-vsync-active-high:     deprecated prop that can parsed from drm_display_mode.
+-hsync-active-high:     deprecated prop that can parsed from drm_display_mode.
+-samsung,ycbcr-coeff:   deprecated prop that can parsed from drm_display_mode.
+-samsung,dynamic-range: deprecated prop that can parsed from drm_display_mode.
+-samsung,color-space:   deprecated prop that can parsed from drm_display_info.
+-samsung,color-depth:   deprecated prop that can parsed from drm_display_info.
+-samsung,link-rate:     deprecated prop that can reading from monitor by dpcd method.
+-samsung,lane-count:    deprecated prop that can reading from monitor by dpcd method.
+-samsung,hpd-gpio:      deprecated name for hpd-gpios.
+
+-------------------------------------------------------------------------------
 
 Example:
 
@@ -112,13 +89,6 @@ SOC specific portion:
 
 Board Specific portion:
 	dp-controller {
-		samsung,color-space = <0>;
-		samsung,dynamic-range = <0>;
-		samsung,ycbcr-coeff = <0>;
-		samsung,color-depth = <1>;
-		samsung,link-rate = <0x0a>;
-		samsung,lane-count = <4>;
-
 		display-timings {
 			native-mode = <&lcd_timing>;
 			lcd_timing: 1366x768 {
@@ -135,18 +105,9 @@ Board Specific portion:
 		};
 
 		ports {
-			port {
+			port@0 {
 				dp_out: endpoint {
-					remote-endpoint = <&dp_in>;
-				};
-			};
-		};
-
-		panel {
-			...
-			port {
-				dp_in: endpoint {
-					remote-endpoint = <&dp_out>;
+					remote-endpoint = <&bridge_in>;
 				};
 			};
 		};

Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt

+Rockchip RK3288 specific extensions to the Analogix Display Port
+================================
+
+Required properties:
+- compatible: "rockchip,rk3288-edp";
+
+- reg: physical base address of the controller and length
+
+- clocks: from common clock binding: handle to dp clock.
+	  of memory mapped region.
+
+- clock-names: from common clock binding:
+	       Required elements: "dp" "pclk"
+
+- resets: Must contain an entry for each entry in reset-names.
+	  See ../reset/reset.txt for details.
+
+- pinctrl-names: Names corresponding to the chip hotplug pinctrl states.
+- pinctrl-0: pin-control mode. should be <&edp_hpd>
+
+- reset-names: Must include the name "dp"
+
+- rockchip,grf: this soc should set GRF regs, so need get grf here.
+
+- ports: there are 2 port nodes with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt.
+    Port 0: contained 2 endpoints, connecting to the output of vop.
+    Port 1: contained 1 endpoint, connecting to the input of panel.
+
+For the below properties, please refer to Analogix DP binding document:
+ * Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt
+- phys (required)
+- phy-names (required)
+- hpd-gpios (optional)
+- force-hpd (optional)
+-------------------------------------------------------------------------------
+
+Example:
+	dp-controller: dp@ff970000 {
+		compatible = "rockchip,rk3288-dp";
+		reg = <0xff970000 0x4000>;
+		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_EDP>, <&cru PCLK_EDP_CTRL>;
+		clock-names = "dp", "pclk";
+		phys = <&dp_phy>;
+		phy-names = "dp";
+
+		rockchip,grf = <&grf>;
+		resets = <&cru 111>;
+		reset-names = "dp";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_hpd>;
+
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			edp_in: port@0 {
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				edp_in_vopb: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&vopb_out_edp>;
+				};
+				edp_in_vopl: endpoint@1 {
+					reg = <1>;
+					remote-endpoint = <&vopl_out_edp>;
+				};
+			};
+
+			edp_out: port@1 {
+				reg = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				edp_out_panel: endpoint {
+					reg = <0>;
+					remote-endpoint = <&panel_in_edp>
+				};
+			};
+		};
+	};
+
+	pinctrl {
+		edp {
+			edp_hpd: edp-hpd {
+				rockchip,pins = <7 11 RK_FUNC_2 &pcfg_pull_none>;
+			};
+		};
+	};

arch/arm/boot/dts/exynos5250-arndale.dts

@@ -124,8 +124,6 @@
 &dp {
 	status = "okay";
 	samsung,color-space = <0>;
-	samsung,dynamic-range = <0>;
-	samsung,ycbcr-coeff = <0>;
 	samsung,color-depth = <1>;
 	samsung,link-rate = <0x0a>;
 	samsung,lane-count = <4>;

arch/arm/boot/dts/exynos5250-smdk5250.dts

@@ -80,8 +80,6 @@
 
 &dp {
 	samsung,color-space = <0>;
-	samsung,dynamic-range = <0>;
-	samsung,ycbcr-coeff = <0>;
 	samsung,color-depth = <1>;
 	samsung,link-rate = <0x0a>;
 	samsung,lane-count = <4>;

arch/arm/boot/dts/exynos5250-snow-common.dtsi

@@ -236,12 +236,10 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&dp_hpd>;
 	samsung,color-space = <0>;
-	samsung,dynamic-range = <0>;
-	samsung,ycbcr-coeff = <0>;
 	samsung,color-depth = <1>;
 	samsung,link-rate = <0x0a>;
 	samsung,lane-count = <2>;
-	samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>;
+	hpd-gpios = <&gpx0 7 GPIO_ACTIVE_HIGH>;
 
 	ports {
 		port@0 {

arch/arm/boot/dts/exynos5250-spring.dts

@@ -74,12 +74,10 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&dp_hpd_gpio>;
 	samsung,color-space = <0>;
-	samsung,dynamic-range = <0>;
-	samsung,ycbcr-coeff = <0>;
 	samsung,color-depth = <1>;
 	samsung,link-rate = <0x0a>;
 	samsung,lane-count = <1>;
-	samsung,hpd-gpio = <&gpc3 0 GPIO_ACTIVE_HIGH>;
+	hpd-gpios = <&gpc3 0 GPIO_ACTIVE_HIGH>;
 };
 
 &ehci {

arch/arm/boot/dts/exynos5420-peach-pit.dts

@@ -157,12 +157,10 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&dp_hpd_gpio>;
 	samsung,color-space = <0>;
-	samsung,dynamic-range = <0>;
-	samsung,ycbcr-coeff = <0>;
 	samsung,color-depth = <1>;
 	samsung,link-rate = <0x06>;
 	samsung,lane-count = <2>;
-	samsung,hpd-gpio = <&gpx2 6 GPIO_ACTIVE_HIGH>;
+	hpd-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
 
 	ports {
 		port@0 {

arch/arm/boot/dts/exynos5420-smdk5420.dts

@@ -102,8 +102,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&dp_hpd>;
 	samsung,color-space = <0>;
-	samsung,dynamic-range = <0>;
-	samsung,ycbcr-coeff = <0>;
 	samsung,color-depth = <1>;
 	samsung,link-rate = <0x0a>;
 	samsung,lane-count = <4>;

arch/arm/boot/dts/exynos5800-peach-pi.dts

@@ -157,8 +157,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&dp_hpd_gpio>;
 	samsung,color-space = <0>;
-	samsung,dynamic-range = <0>;
-	samsung,ycbcr-coeff = <0>;
 	samsung,color-depth = <1>;
 	samsung,link-rate = <0x0a>;
 	samsung,lane-count = <2>;

drivers/gpu/drm/bridge/Kconfig

@@ -40,4 +40,6 @@ config DRM_PARADE_PS8622
 	---help---
 	  Parade eDP-LVDS bridge chip driver.
 
+source "drivers/gpu/drm/bridge/analogix/Kconfig"
+
 endmenu

drivers/gpu/drm/bridge/Makefile

@@ -4,3 +4,4 @@ obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o
 obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
 obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
 obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
+obj-$(CONFIG_DRM_ANALOGIX_DP) += analogix/

drivers/gpu/drm/bridge/analogix/Kconfig

+config DRM_ANALOGIX_DP
+	tristate
+	depends on DRM

drivers/gpu/drm/bridge/analogix/Makefile

+analogix_dp-objs := analogix_dp_core.o analogix_dp_reg.o
+obj-$(CONFIG_DRM_ANALOGIX_DP) += analogix_dp.o

drivers/gpu/drm/exynos/exynos_dp_core.h → drivers/gpu/drm/bridge/analogix/analogix_dp_core.h

 /*
- * Header file for Samsung DP (Display Port) interface driver.
+ * Header file for Analogix DP (Display Port) core interface driver.
  *
  * Copyright (C) 2012 Samsung Electronics Co., Ltd.
  * Author: Jingoo Han <jg1.han@samsung.com>
@@ -10,24 +10,37 @@
  * option) any later version.
  */
 
-#ifndef _EXYNOS_DP_CORE_H
-#define _EXYNOS_DP_CORE_H
+#ifndef _ANALOGIX_DP_CORE_H
+#define _ANALOGIX_DP_CORE_H
 
 #include <drm/drm_crtc.h>
 #include <drm/drm_dp_helper.h>
-#include <drm/exynos_drm.h>
-#include <video/videomode.h>
-
-#include "exynos_drm_drv.h"
 
 #define DP_TIMEOUT_LOOP_COUNT 100
 #define MAX_CR_LOOP 5
 #define MAX_EQ_LOOP 5
 
-enum link_rate_type {
-	LINK_RATE_1_62GBPS = 0x06,
-	LINK_RATE_2_70GBPS = 0x0a
-};
+/* I2C EDID Chip ID, Slave Address */
+#define I2C_EDID_DEVICE_ADDR			0x50
+#define I2C_E_EDID_DEVICE_ADDR			0x30
+
+#define EDID_BLOCK_LENGTH			0x80
+#define EDID_HEADER_PATTERN			0x00
+#define EDID_EXTENSION_FLAG			0x7e
+#define EDID_CHECKSUM				0x7f
+
+/* DP_MAX_LANE_COUNT */
+#define DPCD_ENHANCED_FRAME_CAP(x)		(((x) >> 7) & 0x1)
+#define DPCD_MAX_LANE_COUNT(x)			((x) & 0x1f)
+
+/* DP_LANE_COUNT_SET */
+#define DPCD_LANE_COUNT_SET(x)			((x) & 0x1f)
+
+/* DP_TRAINING_LANE0_SET */
+#define DPCD_PRE_EMPHASIS_SET(x)		(((x) & 0x3) << 3)
+#define DPCD_PRE_EMPHASIS_GET(x)		(((x) >> 3) & 0x3)
+#define DPCD_VOLTAGE_SWING_SET(x)		(((x) & 0x3) << 0)
+#define DPCD_VOLTAGE_SWING_GET(x)		(((x) >> 0) & 0x3)
 
 enum link_lane_count_type {
 	LANE_COUNT1 = 1,
@@ -132,8 +145,8 @@ struct video_info {
 	enum color_coefficient ycbcr_coeff;
 	enum color_depth color_depth;
 
-	enum link_rate_type link_rate;
-	enum link_lane_count_type lane_count;
+	int max_link_rate;
+	enum link_lane_count_type max_lane_count;
 };
 
 struct link_train {
@@ -147,136 +160,122 @@ struct link_train {
 	enum link_training_state lt_state;
 };
 
-struct exynos_dp_device {
-	struct drm_encoder	encoder;
+struct analogix_dp_device {
+	struct drm_encoder	*encoder;
 	struct device		*dev;
 	struct drm_device	*drm_dev;
 	struct drm_connector	connector;
-	struct drm_panel	*panel;
 	struct drm_bridge	*bridge;
-	struct drm_bridge	*ptn_bridge;
 	struct clk		*clock;
 	unsigned int		irq;
 	void __iomem		*reg_base;
 
-	struct video_info	*video_info;
+	struct video_info	video_info;
 	struct link_train	link_train;
-	struct work_struct	hotplug_work;
 	struct phy		*phy;
 	int			dpms_mode;
 	int			hpd_gpio;
-	struct videomode	vm;
-};
+	bool                    force_hpd;
+	unsigned char           edid[EDID_BLOCK_LENGTH * 2];
 
-/* exynos_dp_reg.c */
-void exynos_dp_enable_video_mute(struct exynos_dp_device *dp, bool enable);
-void exynos_dp_stop_video(struct exynos_dp_device *dp);
-void exynos_dp_lane_swap(struct exynos_dp_device *dp, bool enable);
-void exynos_dp_init_analog_param(struct exynos_dp_device *dp);
-void exynos_dp_init_interrupt(struct exynos_dp_device *dp);
-void exynos_dp_reset(struct exynos_dp_device *dp);
-void exynos_dp_swreset(struct exynos_dp_device *dp);
-void exynos_dp_config_interrupt(struct exynos_dp_device *dp);
-enum pll_status exynos_dp_get_pll_lock_status(struct exynos_dp_device *dp);
-void exynos_dp_set_pll_power_down(struct exynos_dp_device *dp, bool enable);
-void exynos_dp_set_analog_power_down(struct exynos_dp_device *dp,
-				enum analog_power_block block,
-				bool enable);
-void exynos_dp_init_analog_func(struct exynos_dp_device *dp);
-void exynos_dp_init_hpd(struct exynos_dp_device *dp);
-enum dp_irq_type exynos_dp_get_irq_type(struct exynos_dp_device *dp);
-void exynos_dp_clear_hotplug_interrupts(struct exynos_dp_device *dp);
-void exynos_dp_reset_aux(struct exynos_dp_device *dp);
-void exynos_dp_init_aux(struct exynos_dp_device *dp);
-int exynos_dp_get_plug_in_status(struct exynos_dp_device *dp);
-void exynos_dp_enable_sw_function(struct exynos_dp_device *dp);
-int exynos_dp_start_aux_transaction(struct exynos_dp_device *dp);
-int exynos_dp_write_byte_to_dpcd(struct exynos_dp_device *dp,
-				unsigned int reg_addr,
-				unsigned char data);
-int exynos_dp_read_byte_from_dpcd(struct exynos_dp_device *dp,
-				unsigned int reg_addr,
-				unsigned char *data);
-int exynos_dp_write_bytes_to_dpcd(struct exynos_dp_device *dp,
-				unsigned int reg_addr,
-				unsigned int count,
-				unsigned char data[]);
-int exynos_dp_read_bytes_from_dpcd(struct exynos_dp_device *dp,
-				unsigned int reg_addr,
-				unsigned int count,
-				unsigned char data[]);
-int exynos_dp_select_i2c_device(struct exynos_dp_device *dp,
-				unsigned int device_addr,
-				unsigned int reg_addr);
-int exynos_dp_read_byte_from_i2c(struct exynos_dp_device *dp,
-				unsigned int device_addr,
-				unsigned int reg_addr,
-				unsigned int *data);
-int exynos_dp_read_bytes_from_i2c(struct exynos_dp_device *dp,
-				unsigned int device_addr,
-				unsigned int reg_addr,
-				unsigned int count,
-				unsigned char edid[]);
-void exynos_dp_set_link_bandwidth(struct exynos_dp_device *dp, u32 bwtype);
-void exynos_dp_get_link_bandwidth(struct exynos_dp_device *dp, u32 *bwtype);
-void exynos_dp_set_lane_count(struct exynos_dp_device *dp, u32 count);
-void exynos_dp_get_lane_count(struct exynos_dp_device *dp, u32 *count);
-void exynos_dp_enable_enhanced_mode(struct exynos_dp_device *dp, bool enable);
-void exynos_dp_set_training_pattern(struct exynos_dp_device *dp,
-				 enum pattern_set pattern);
-void exynos_dp_set_lane0_pre_emphasis(struct exynos_dp_device *dp, u32 level);
-void exynos_dp_set_lane1_pre_emphasis(struct exynos_dp_device *dp, u32 level);
-void exynos_dp_set_lane2_pre_emphasis(struct exynos_dp_device *dp, u32 level);
-void exynos_dp_set_lane3_pre_emphasis(struct exynos_dp_device *dp, u32 level);
-void exynos_dp_set_lane0_link_training(struct exynos_dp_device *dp,
-				u32 training_lane);
-void exynos_dp_set_lane1_link_training(struct exynos_dp_device *dp,
-				u32 training_lane);
-void exynos_dp_set_lane2_link_training(struct exynos_dp_device *dp,
-				u32 training_lane);
-void exynos_dp_set_lane3_link_training(struct exynos_dp_device *dp,
-				u32 training_lane);
-u32 exynos_dp_get_lane0_link_training(struct exynos_dp_device *dp);
-u32 exynos_dp_get_lane1_link_training(struct exynos_dp_device *dp);
-u32 exynos_dp_get_lane2_link_training(struct exynos_dp_device *dp);
-u32 exynos_dp_get_lane3_link_training(struct exynos_dp_device *dp);
-void exynos_dp_reset_macro(struct exynos_dp_device *dp);
-void exynos_dp_init_video(struct exynos_dp_device *dp);
-
-void exynos_dp_set_video_color_format(struct exynos_dp_device *dp);
-int exynos_dp_is_slave_video_stream_clock_on(struct exynos_dp_device *dp);
-void exynos_dp_set_video_cr_mn(struct exynos_dp_device *dp,
-			enum clock_recovery_m_value_type type,
-			u32 m_value,
-			u32 n_value);
-void exynos_dp_set_video_timing_mode(struct exynos_dp_device *dp, u32 type);
-void exynos_dp_enable_video_master(struct exynos_dp_device *dp, bool enable);
-void exynos_dp_start_video(struct exynos_dp_device *dp);
-int exynos_dp_is_video_stream_on(struct exynos_dp_device *dp);
-void exynos_dp_config_video_slave_mode(struct exynos_dp_device *dp);
-void exynos_dp_enable_scrambling(struct exynos_dp_device *dp);
-void exynos_dp_disable_scrambling(struct exynos_dp_device *dp);
-
-/* I2C EDID Chip ID, Slave Address */
-#define I2C_EDID_DEVICE_ADDR			0x50
-#define I2C_E_EDID_DEVICE_ADDR			0x30
-
-#define EDID_BLOCK_LENGTH			0x80
-#define EDID_HEADER_PATTERN			0x00
-#define EDID_EXTENSION_FLAG			0x7e
-#define EDID_CHECKSUM				0x7f
-
-/* DP_MAX_LANE_COUNT */
-#define DPCD_ENHANCED_FRAME_CAP(x)		(((x) >> 7) & 0x1)
-#define DPCD_MAX_LANE_COUNT(x)			((x) & 0x1f)
-
-/* DP_LANE_COUNT_SET */
-#define DPCD_LANE_COUNT_SET(x)			((x) & 0x1f)
-
-/* DP_TRAINING_LANE0_SET */
-#define DPCD_PRE_EMPHASIS_SET(x)		(((x) & 0x3) << 3)
-#define DPCD_PRE_EMPHASIS_GET(x)		(((x) >> 3) & 0x3)
-#define DPCD_VOLTAGE_SWING_SET(x)		(((x) & 0x3) << 0)
-#define DPCD_VOLTAGE_SWING_GET(x)		(((x) >> 0) & 0x3)
+	struct analogix_dp_plat_data *plat_data;
+};
 
-#endif /* _EXYNOS_DP_CORE_H */
+/* analogix_dp_reg.c */
+void analogix_dp_enable_video_mute(struct analogix_dp_device *dp, bool enable);
+void analogix_dp_stop_video(struct analogix_dp_device *dp);
+void analogix_dp_lane_swap(struct analogix_dp_device *dp, bool enable);
+void analogix_dp_init_analog_param(struct analogix_dp_device *dp);
+void analogix_dp_init_interrupt(struct analogix_dp_device *dp);
+void analogix_dp_reset(struct analogix_dp_device *dp);
+void analogix_dp_swreset(struct analogix_dp_device *dp);
+void analogix_dp_config_interrupt(struct analogix_dp_device *dp);
+void analogix_dp_mute_hpd_interrupt(struct analogix_dp_device *dp);
+void analogix_dp_unmute_hpd_interrupt(struct analogix_dp_device *dp);
+enum pll_status analogix_dp_get_pll_lock_status(struct analogix_dp_device *dp);
+void analogix_dp_set_pll_power_down(struct analogix_dp_device *dp, bool enable);
+void analogix_dp_set_analog_power_down(struct analogix_dp_device *dp,
+				       enum analog_power_block block,
+				       bool enable);
+void analogix_dp_init_analog_func(struct analogix_dp_device *dp);
+void analogix_dp_init_hpd(struct analogix_dp_device *dp);
+void analogix_dp_force_hpd(struct analogix_dp_device *dp);
+enum dp_irq_type analogix_dp_get_irq_type(struct analogix_dp_device *dp);
+void analogix_dp_clear_hotplug_interrupts(struct analogix_dp_device *dp);
+void analogix_dp_reset_aux(struct analogix_dp_device *dp);
+void analogix_dp_init_aux(struct analogix_dp_device *dp);
+int analogix_dp_get_plug_in_status(struct analogix_dp_device *dp);
+void analogix_dp_enable_sw_function(struct analogix_dp_device *dp);
+int analogix_dp_start_aux_transaction(struct analogix_dp_device *dp);
+int analogix_dp_write_byte_to_dpcd(struct analogix_dp_device *dp,
+				   unsigned int reg_addr,
+				   unsigned char data);
+int analogix_dp_read_byte_from_dpcd(struct analogix_dp_device *dp,
+				    unsigned int reg_addr,
+				    unsigned char *data);
+int analogix_dp_write_bytes_to_dpcd(struct analogix_dp_device *dp,
+				    unsigned int reg_addr,
+				    unsigned int count,
+				    unsigned char data[]);
+int analogix_dp_read_bytes_from_dpcd(struct analogix_dp_device *dp,
+				     unsigned int reg_addr,
+				     unsigned int count,
+				     unsigned char data[]);
+int analogix_dp_select_i2c_device(struct analogix_dp_device *dp,
+				  unsigned int device_addr,
+				  unsigned int reg_addr);
+int analogix_dp_read_byte_from_i2c(struct analogix_dp_device *dp,
+				   unsigned int device_addr,
+				   unsigned int reg_addr,
+				   unsigned int *data);
+int analogix_dp_read_bytes_from_i2c(struct analogix_dp_device *dp,
+				    unsigned int device_addr,
+				    unsigned int reg_addr,
+				    unsigned int count,
+				    unsigned char edid[]);
+void analogix_dp_set_link_bandwidth(struct analogix_dp_device *dp, u32 bwtype);
+void analogix_dp_get_link_bandwidth(struct analogix_dp_device *dp, u32 *bwtype);
+void analogix_dp_set_lane_count(struct analogix_dp_device *dp, u32 count);
+void analogix_dp_get_lane_count(struct analogix_dp_device *dp, u32 *count);
+void analogix_dp_enable_enhanced_mode(struct analogix_dp_device *dp,
+				      bool enable);
+void analogix_dp_set_training_pattern(struct analogix_dp_device *dp,
+				      enum pattern_set pattern);
+void analogix_dp_set_lane0_pre_emphasis(struct analogix_dp_device *dp,
+					u32 level);
+void analogix_dp_set_lane1_pre_emphasis(struct analogix_dp_device *dp,
+					u32 level);
+void analogix_dp_set_lane2_pre_emphasis(struct analogix_dp_device *dp,
+					u32 level);
+void analogix_dp_set_lane3_pre_emphasis(struct analogix_dp_device *dp,
+					u32 level);
+void analogix_dp_set_lane0_link_training(struct analogix_dp_device *dp,
+					 u32 training_lane);
+void analogix_dp_set_lane1_link_training(struct analogix_dp_device *dp,
+					 u32 training_lane);
+void analogix_dp_set_lane2_link_training(struct analogix_dp_device *dp,
+					 u32 training_lane);
+void analogix_dp_set_lane3_link_training(struct analogix_dp_device *dp,
+					 u32 training_lane);
+u32 analogix_dp_get_lane0_link_training(struct analogix_dp_device *dp);
+u32 analogix_dp_get_lane1_link_training(struct analogix_dp_device *dp);
+u32 analogix_dp_get_lane2_link_training(struct analogix_dp_device *dp);
+u32 analogix_dp_get_lane3_link_training(struct analogix_dp_device *dp);
+void analogix_dp_reset_macro(struct analogix_dp_device *dp);
+void analogix_dp_init_video(struct analogix_dp_device *dp);
+
+void analogix_dp_set_video_color_format(struct analogix_dp_device *dp);
+int analogix_dp_is_slave_video_stream_clock_on(struct analogix_dp_device *dp);
+void analogix_dp_set_video_cr_mn(struct analogix_dp_device *dp,
+				 enum clock_recovery_m_value_type type,
+				 u32 m_value,
+				 u32 n_value);
+void analogix_dp_set_video_timing_mode(struct analogix_dp_device *dp, u32 type);
+void analogix_dp_enable_video_master(struct analogix_dp_device *dp,
+				     bool enable);
+void analogix_dp_start_video(struct analogix_dp_device *dp);
+int analogix_dp_is_video_stream_on(struct analogix_dp_device *dp);
+void analogix_dp_config_video_slave_mode(struct analogix_dp_device *dp);
+void analogix_dp_enable_scrambling(struct analogix_dp_device *dp);
+void analogix_dp_disable_scrambling(struct analogix_dp_device *dp);
+#endif /* _ANALOGIX_DP_CORE_H */

drivers/gpu/drm/exynos/exynos_dp_reg.h → drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h

 /*
- * Register definition file for Samsung DP driver
+ * Register definition file for Analogix DP core driver
  *
  * Copyright (C) 2012 Samsung Electronics Co., Ltd.
  * Author: Jingoo Han <jg1.han@samsung.com>
@@ -9,96 +9,104 @@
  * published by the Free Software Foundation.
  */
 
-#ifndef _EXYNOS_DP_REG_H
-#define _EXYNOS_DP_REG_H
-
-#define EXYNOS_DP_TX_SW_RESET			0x14
-#define EXYNOS_DP_FUNC_EN_1			0x18
-#define EXYNOS_DP_FUNC_EN_2			0x1C
-#define EXYNOS_DP_VIDEO_CTL_1			0x20
-#define EXYNOS_DP_VIDEO_CTL_2			0x24
-#define EXYNOS_DP_VIDEO_CTL_3			0x28
-
-#define EXYNOS_DP_VIDEO_CTL_8			0x3C
-#define EXYNOS_DP_VIDEO_CTL_10			0x44
-
-#define EXYNOS_DP_LANE_MAP			0x35C
-
-#define EXYNOS_DP_ANALOG_CTL_1			0x370
-#define EXYNOS_DP_ANALOG_CTL_2			0x374
-#define EXYNOS_DP_ANALOG_CTL_3			0x378
-#define EXYNOS_DP_PLL_FILTER_CTL_1		0x37C
-#define EXYNOS_DP_TX_AMP_TUNING_CTL		0x380
-
-#define EXYNOS_DP_AUX_HW_RETRY_CTL		0x390
-
-#define EXYNOS_DP_COMMON_INT_STA_1		0x3C4
-#define EXYNOS_DP_COMMON_INT_STA_2		0x3C8
-#define EXYNOS_DP_COMMON_INT_STA_3		0x3CC
-#define EXYNOS_DP_COMMON_INT_STA_4		0x3D0
-#define EXYNOS_DP_INT_STA			0x3DC
-#define EXYNOS_DP_COMMON_INT_MASK_1		0x3E0
-#define EXYNOS_DP_COMMON_INT_MASK_2		0x3E4
-#define EXYNOS_DP_COMMON_INT_MASK_3		0x3E8
-#define EXYNOS_DP_COMMON_INT_MASK_4		0x3EC
-#define EXYNOS_DP_INT_STA_MASK			0x3F8
-#define EXYNOS_DP_INT_CTL			0x3FC
-
-#define EXYNOS_DP_SYS_CTL_1			0x600
-#define EXYNOS_DP_SYS_CTL_2			0x604
-#define EXYNOS_DP_SYS_CTL_3			0x608
-#define EXYNOS_DP_SYS_CTL_4			0x60C
-
-#define EXYNOS_DP_PKT_SEND_CTL			0x640
-#define EXYNOS_DP_HDCP_CTL			0x648
-
-#define EXYNOS_DP_LINK_BW_SET			0x680
-#define EXYNOS_DP_LANE_COUNT_SET		0x684
-#define EXYNOS_DP_TRAINING_PTN_SET		0x688
-#define EXYNOS_DP_LN0_LINK_TRAINING_CTL		0x68C
-#define EXYNOS_DP_LN1_LINK_TRAINING_CTL		0x690
-#define EXYNOS_DP_LN2_LINK_TRAINING_CTL		0x694
-#define EXYNOS_DP_LN3_LINK_TRAINING_CTL		0x698
-
-#define EXYNOS_DP_DEBUG_CTL			0x6C0
-#define EXYNOS_DP_HPD_DEGLITCH_L		0x6C4
-#define EXYNOS_DP_HPD_DEGLITCH_H		0x6C8
-#define EXYNOS_DP_LINK_DEBUG_CTL		0x6E0
-
-#define EXYNOS_DP_M_VID_0			0x700
-#define EXYNOS_DP_M_VID_1			0x704
-#define EXYNOS_DP_M_VID_2			0x708
-#define EXYNOS_DP_N_VID_0			0x70C
-#define EXYNOS_DP_N_VID_1			0x710
-#define EXYNOS_DP_N_VID_2			0x714
-
-#define EXYNOS_DP_PLL_CTL			0x71C
-#define EXYNOS_DP_PHY_PD			0x720
-#define EXYNOS_DP_PHY_TEST			0x724
-
-#define EXYNOS_DP_VIDEO_FIFO_THRD		0x730
-#define EXYNOS_DP_AUDIO_MARGIN			0x73C
-
-#define EXYNOS_DP_M_VID_GEN_FILTER_TH		0x764
-#define EXYNOS_DP_M_AUD_GEN_FILTER_TH		0x778
-#define EXYNOS_DP_AUX_CH_STA			0x780
-#define EXYNOS_DP_AUX_CH_DEFER_CTL		0x788
-#define EXYNOS_DP_AUX_RX_COMM			0x78C
-#define EXYNOS_DP_BUFFER_DATA_CTL		0x790
-#define EXYNOS_DP_AUX_CH_CTL_1			0x794
-#define EXYNOS_DP_AUX_ADDR_7_0			0x798
-#define EXYNOS_DP_AUX_ADDR_15_8			0x79C
-#define EXYNOS_DP_AUX_ADDR_19_16		0x7A0
-#define EXYNOS_DP_AUX_CH_CTL_2			0x7A4
-
-#define EXYNOS_DP_BUF_DATA_0			0x7C0
-
-#define EXYNOS_DP_SOC_GENERAL_CTL		0x800
-
-/* EXYNOS_DP_TX_SW_RESET */
+#ifndef _ANALOGIX_DP_REG_H
+#define _ANALOGIX_DP_REG_H
+
+#define ANALOGIX_DP_TX_SW_RESET			0x14
+#define ANALOGIX_DP_FUNC_EN_1			0x18
+#define ANALOGIX_DP_FUNC_EN_2			0x1C
+#define ANALOGIX_DP_VIDEO_CTL_1			0x20
+#define ANALOGIX_DP_VIDEO_CTL_2			0x24
+#define ANALOGIX_DP_VIDEO_CTL_3			0x28
+
+#define ANALOGIX_DP_VIDEO_CTL_8			0x3C
+#define ANALOGIX_DP_VIDEO_CTL_10		0x44
+
+#define ANALOGIX_DP_PLL_REG_1			0xfc
+#define ANALOGIX_DP_PLL_REG_2			0x9e4
+#define ANALOGIX_DP_PLL_REG_3			0x9e8
+#define ANALOGIX_DP_PLL_REG_4			0x9ec
+#define ANALOGIX_DP_PLL_REG_5			0xa00
+
+#define ANALOGIX_DP_PD				0x12c
+
+#define ANALOGIX_DP_LANE_MAP			0x35C
+
+#define ANALOGIX_DP_ANALOG_CTL_1		0x370
+#define ANALOGIX_DP_ANALOG_CTL_2		0x374
+#define ANALOGIX_DP_ANALOG_CTL_3		0x378
+#define ANALOGIX_DP_PLL_FILTER_CTL_1		0x37C
+#define ANALOGIX_DP_TX_AMP_TUNING_CTL		0x380
+
+#define ANALOGIX_DP_AUX_HW_RETRY_CTL		0x390
+
+#define ANALOGIX_DP_COMMON_INT_STA_1		0x3C4
+#define ANALOGIX_DP_COMMON_INT_STA_2		0x3C8
+#define ANALOGIX_DP_COMMON_INT_STA_3		0x3CC
+#define ANALOGIX_DP_COMMON_INT_STA_4		0x3D0
+#define ANALOGIX_DP_INT_STA			0x3DC
+#define ANALOGIX_DP_COMMON_INT_MASK_1		0x3E0
+#define ANALOGIX_DP_COMMON_INT_MASK_2		0x3E4
+#define ANALOGIX_DP_COMMON_INT_MASK_3		0x3E8
+#define ANALOGIX_DP_COMMON_INT_MASK_4		0x3EC
+#define ANALOGIX_DP_INT_STA_MASK		0x3F8
+#define ANALOGIX_DP_INT_CTL			0x3FC
+
+#define ANALOGIX_DP_SYS_CTL_1			0x600
+#define ANALOGIX_DP_SYS_CTL_2			0x604
+#define ANALOGIX_DP_SYS_CTL_3			0x608
+#define ANALOGIX_DP_SYS_CTL_4			0x60C
+
+#define ANALOGIX_DP_PKT_SEND_CTL		0x640
+#define ANALOGIX_DP_HDCP_CTL			0x648
+
+#define ANALOGIX_DP_LINK_BW_SET			0x680
+#define ANALOGIX_DP_LANE_COUNT_SET		0x684
+#define ANALOGIX_DP_TRAINING_PTN_SET		0x688
+#define ANALOGIX_DP_LN0_LINK_TRAINING_CTL	0x68C
+#define ANALOGIX_DP_LN1_LINK_TRAINING_CTL	0x690
+#define ANALOGIX_DP_LN2_LINK_TRAINING_CTL	0x694
+#define ANALOGIX_DP_LN3_LINK_TRAINING_CTL	0x698
+
+#define ANALOGIX_DP_DEBUG_CTL			0x6C0
+#define ANALOGIX_DP_HPD_DEGLITCH_L		0x6C4
+#define ANALOGIX_DP_HPD_DEGLITCH_H		0x6C8
+#define ANALOGIX_DP_LINK_DEBUG_CTL		0x6E0
+
+#define ANALOGIX_DP_M_VID_0			0x700
+#define ANALOGIX_DP_M_VID_1			0x704
+#define ANALOGIX_DP_M_VID_2			0x708
+#define ANALOGIX_DP_N_VID_0			0x70C
+#define ANALOGIX_DP_N_VID_1			0x710
+#define ANALOGIX_DP_N_VID_2			0x714
+
+#define ANALOGIX_DP_PLL_CTL			0x71C
+#define ANALOGIX_DP_PHY_PD			0x720
+#define ANALOGIX_DP_PHY_TEST			0x724
+
+#define ANALOGIX_DP_VIDEO_FIFO_THRD		0x730
+#define ANALOGIX_DP_AUDIO_MARGIN		0x73C
+
+#define ANALOGIX_DP_M_VID_GEN_FILTER_TH		0x764
+#define ANALOGIX_DP_M_AUD_GEN_FILTER_TH		0x778
+#define ANALOGIX_DP_AUX_CH_STA			0x780
+#define ANALOGIX_DP_AUX_CH_DEFER_CTL		0x788
+#define ANALOGIX_DP_AUX_RX_COMM			0x78C
+#define ANALOGIX_DP_BUFFER_DATA_CTL		0x790
+#define ANALOGIX_DP_AUX_CH_CTL_1		0x794
+#define ANALOGIX_DP_AUX_ADDR_7_0		0x798
+#define ANALOGIX_DP_AUX_ADDR_15_8		0x79C
+#define ANALOGIX_DP_AUX_ADDR_19_16		0x7A0
+#define ANALOGIX_DP_AUX_CH_CTL_2		0x7A4
+
+#define ANALOGIX_DP_BUF_DATA_0			0x7C0
+
+#define ANALOGIX_DP_SOC_GENERAL_CTL		0x800
+
+/* ANALOGIX_DP_TX_SW_RESET */
 #define RESET_DP_TX				(0x1 << 0)
 
-/* EXYNOS_DP_FUNC_EN_1 */
+/* ANALOGIX_DP_FUNC_EN_1 */
 #define MASTER_VID_FUNC_EN_N			(0x1 << 7)
 #define SLAVE_VID_FUNC_EN_N			(0x1 << 5)
 #define AUD_FIFO_FUNC_EN_N			(0x1 << 4)
@@ -107,17 +115,17 @@
 #define CRC_FUNC_EN_N				(0x1 << 1)
 #define SW_FUNC_EN_N				(0x1 << 0)
 
-/* EXYNOS_DP_FUNC_EN_2 */
+/* ANALOGIX_DP_FUNC_EN_2 */
 #define SSC_FUNC_EN_N				(0x1 << 7)
 #define AUX_FUNC_EN_N				(0x1 << 2)
 #define SERDES_FIFO_FUNC_EN_N			(0x1 << 1)
 #define LS_CLK_DOMAIN_FUNC_EN_N			(0x1 << 0)
 
-/* EXYNOS_DP_VIDEO_CTL_1 */
+/* ANALOGIX_DP_VIDEO_CTL_1 */
 #define VIDEO_EN				(0x1 << 7)
 #define HDCP_VIDEO_MUTE				(0x1 << 6)
 
-/* EXYNOS_DP_VIDEO_CTL_1 */
+/* ANALOGIX_DP_VIDEO_CTL_1 */
 #define IN_D_RANGE_MASK				(0x1 << 7)
 #define IN_D_RANGE_SHIFT			(7)
 #define IN_D_RANGE_CEA				(0x1 << 7)
@@ -134,7 +142,7 @@
 #define IN_COLOR_F_YCBCR422			(0x1 << 0)
 #define IN_COLOR_F_RGB				(0x0 << 0)
 
-/* EXYNOS_DP_VIDEO_CTL_3 */
+/* ANALOGIX_DP_VIDEO_CTL_3 */
 #define IN_YC_COEFFI_MASK			(0x1 << 7)
 #define IN_YC_COEFFI_SHIFT			(7)
 #define IN_YC_COEFFI_ITU709			(0x1 << 7)
@@ -144,17 +152,21 @@
 #define VID_CHK_UPDATE_TYPE_1			(0x1 << 4)
 #define VID_CHK_UPDATE_TYPE_0			(0x0 << 4)
 
-/* EXYNOS_DP_VIDEO_CTL_8 */
+/* ANALOGIX_DP_VIDEO_CTL_8 */
 #define VID_HRES_TH(x)				(((x) & 0xf) << 4)
 #define VID_VRES_TH(x)				(((x) & 0xf) << 0)
 
-/* EXYNOS_DP_VIDEO_CTL_10 */
+/* ANALOGIX_DP_VIDEO_CTL_10 */
 #define FORMAT_SEL				(0x1 << 4)
 #define INTERACE_SCAN_CFG			(0x1 << 2)
 #define VSYNC_POLARITY_CFG			(0x1 << 1)
 #define HSYNC_POLARITY_CFG			(0x1 << 0)
 
-/* EXYNOS_DP_LANE_MAP */
+/* ANALOGIX_DP_PLL_REG_1 */
+#define REF_CLK_24M				(0x1 << 1)
+#define REF_CLK_27M				(0x0 << 1)
+
+/* ANALOGIX_DP_LANE_MAP */
 #define LANE3_MAP_LOGIC_LANE_0			(0x0 << 6)
 #define LANE3_MAP_LOGIC_LANE_1			(0x1 << 6)
 #define LANE3_MAP_LOGIC_LANE_2			(0x2 << 6)
@@ -172,30 +184,30 @@
 #define LANE0_MAP_LOGIC_LANE_2			(0x2 << 0)
 #define LANE0_MAP_LOGIC_LANE_3			(0x3 << 0)
 
-/* EXYNOS_DP_ANALOG_CTL_1 */
+/* ANALOGIX_DP_ANALOG_CTL_1 */
 #define TX_TERMINAL_CTRL_50_OHM			(0x1 << 4)
 
-/* EXYNOS_DP_ANALOG_CTL_2 */
+/* ANALOGIX_DP_ANALOG_CTL_2 */
 #define SEL_24M					(0x1 << 3)
 #define TX_DVDD_BIT_1_0625V			(0x4 << 0)
 
-/* EXYNOS_DP_ANALOG_CTL_3 */
+/* ANALOGIX_DP_ANALOG_CTL_3 */
 #define DRIVE_DVDD_BIT_1_0625V			(0x4 << 5)
 #define VCO_BIT_600_MICRO			(0x5 << 0)
 
-/* EXYNOS_DP_PLL_FILTER_CTL_1 */
+/* ANALOGIX_DP_PLL_FILTER_CTL_1 */
 #define PD_RING_OSC				(0x1 << 6)
 #define AUX_TERMINAL_CTRL_50_OHM		(0x2 << 4)
 #define TX_CUR1_2X				(0x1 << 2)
 #define TX_CUR_16_MA				(0x3 << 0)
 
-/* EXYNOS_DP_TX_AMP_TUNING_CTL */
+/* ANALOGIX_DP_TX_AMP_TUNING_CTL */
 #define CH3_AMP_400_MV				(0x0 << 24)
 #define CH2_AMP_400_MV				(0x0 << 16)
 #define CH1_AMP_400_MV				(0x0 << 8)
 #define CH0_AMP_400_MV				(0x0 << 0)
 
-/* EXYNOS_DP_AUX_HW_RETRY_CTL */
+/* ANALOGIX_DP_AUX_HW_RETRY_CTL */
 #define AUX_BIT_PERIOD_EXPECTED_DELAY(x)	(((x) & 0x7) << 8)
 #define AUX_HW_RETRY_INTERVAL_MASK		(0x3 << 3)
 #define AUX_HW_RETRY_INTERVAL_600_MICROSECONDS	(0x0 << 3)
@@ -204,7 +216,7 @@
 #define AUX_HW_RETRY_INTERVAL_1800_MICROSECONDS	(0x3 << 3)
 #define AUX_HW_RETRY_COUNT_SEL(x)		(((x) & 0x7) << 0)
 
-/* EXYNOS_DP_COMMON_INT_STA_1 */
+/* ANALOGIX_DP_COMMON_INT_STA_1 */
 #define VSYNC_DET				(0x1 << 7)
 #define PLL_LOCK_CHG				(0x1 << 6)
 #define SPDIF_ERR				(0x1 << 5)
@@ -214,19 +226,19 @@
 #define VID_CLK_CHG				(0x1 << 1)
 #define SW_INT					(0x1 << 0)
 
-/* EXYNOS_DP_COMMON_INT_STA_2 */
+/* ANALOGIX_DP_COMMON_INT_STA_2 */
 #define ENC_EN_CHG				(0x1 << 6)
 #define HW_BKSV_RDY				(0x1 << 3)
 #define HW_SHA_DONE				(0x1 << 2)
 #define HW_AUTH_STATE_CHG			(0x1 << 1)
 #define HW_AUTH_DONE				(0x1 << 0)
 
-/* EXYNOS_DP_COMMON_INT_STA_3 */
+/* ANALOGIX_DP_COMMON_INT_STA_3 */
 #define AFIFO_UNDER				(0x1 << 7)
 #define AFIFO_OVER				(0x1 << 6)
 #define R0_CHK_FLAG				(0x1 << 5)
 
-/* EXYNOS_DP_COMMON_INT_STA_4 */
+/* ANALOGIX_DP_COMMON_INT_STA_4 */
 #define PSR_ACTIVE				(0x1 << 7)
 #define PSR_INACTIVE				(0x1 << 6)
 #define SPDIF_BI_PHASE_ERR			(0x1 << 5)
@@ -234,29 +246,29 @@
 #define HPD_LOST				(0x1 << 1)
 #define PLUG					(0x1 << 0)
 
-/* EXYNOS_DP_INT_STA */
+/* ANALOGIX_DP_INT_STA */
 #define INT_HPD					(0x1 << 6)
 #define HW_TRAINING_FINISH			(0x1 << 5)
 #define RPLY_RECEIV				(0x1 << 1)
 #define AUX_ERR					(0x1 << 0)
 
-/* EXYNOS_DP_INT_CTL */
+/* ANALOGIX_DP_INT_CTL */
 #define SOFT_INT_CTRL				(0x1 << 2)
 #define INT_POL1				(0x1 << 1)
 #define INT_POL0				(0x1 << 0)
 
-/* EXYNOS_DP_SYS_CTL_1 */
+/* ANALOGIX_DP_SYS_CTL_1 */
 #define DET_STA					(0x1 << 2)
 #define FORCE_DET				(0x1 << 1)
 #define DET_CTRL				(0x1 << 0)
 
-/* EXYNOS_DP_SYS_CTL_2 */
+/* ANALOGIX_DP_SYS_CTL_2 */
 #define CHA_CRI(x)				(((x) & 0xf) << 4)
 #define CHA_STA					(0x1 << 2)
 #define FORCE_CHA				(0x1 << 1)
 #define CHA_CTRL				(0x1 << 0)
 
-/* EXYNOS_DP_SYS_CTL_3 */
+/* ANALOGIX_DP_SYS_CTL_3 */
 #define HPD_STATUS				(0x1 << 6)
 #define F_HPD					(0x1 << 5)
 #define HPD_CTRL				(0x1 << 4)
@@ -265,13 +277,13 @@
 #define F_VALID					(0x1 << 1)
 #define VALID_CTRL				(0x1 << 0)
 
-/* EXYNOS_DP_SYS_CTL_4 */
+/* ANALOGIX_DP_SYS_CTL_4 */
 #define FIX_M_AUD				(0x1 << 4)
 #define ENHANCED				(0x1 << 3)
 #define FIX_M_VID				(0x1 << 2)
 #define M_VID_UPDATE_CTRL			(0x3 << 0)
 
-/* EXYNOS_DP_TRAINING_PTN_SET */
+/* ANALOGIX_DP_TRAINING_PTN_SET */
 #define SCRAMBLER_TYPE				(0x1 << 9)
 #define HW_LINK_TRAINING_PATTERN		(0x1 << 8)
 #define SCRAMBLING_DISABLE			(0x1 << 5)
@@ -285,24 +297,24 @@
 #define SW_TRAINING_PATTERN_SET_PTN1		(0x1 << 0)
 #define SW_TRAINING_PATTERN_SET_NORMAL		(0x0 << 0)
 
-/* EXYNOS_DP_LN0_LINK_TRAINING_CTL */
+/* ANALOGIX_DP_LN0_LINK_TRAINING_CTL */
 #define PRE_EMPHASIS_SET_MASK			(0x3 << 3)
 #define PRE_EMPHASIS_SET_SHIFT			(3)
 
-/* EXYNOS_DP_DEBUG_CTL */
+/* ANALOGIX_DP_DEBUG_CTL */
 #define PLL_LOCK				(0x1 << 4)
 #define F_PLL_LOCK				(0x1 << 3)
 #define PLL_LOCK_CTRL				(0x1 << 2)
 #define PN_INV					(0x1 << 0)
 
-/* EXYNOS_DP_PLL_CTL */
+/* ANALOGIX_DP_PLL_CTL */
 #define DP_PLL_PD				(0x1 << 7)
 #define DP_PLL_RESET				(0x1 << 6)
 #define DP_PLL_LOOP_BIT_DEFAULT			(0x1 << 4)
 #define DP_PLL_REF_BIT_1_1250V			(0x5 << 0)
 #define DP_PLL_REF_BIT_1_2500V			(0x7 << 0)
 
-/* EXYNOS_DP_PHY_PD */
+/* ANALOGIX_DP_PHY_PD */
 #define DP_PHY_PD				(0x1 << 5)
 #define AUX_PD					(0x1 << 4)
 #define CH3_PD					(0x1 << 3)
@@ -310,28 +322,28 @@
 #define CH1_PD					(0x1 << 1)
 #define CH0_PD					(0x1 << 0)
 
-/* EXYNOS_DP_PHY_TEST */
+/* ANALOGIX_DP_PHY_TEST */
 #define MACRO_RST				(0x1 << 5)
 #define CH1_TEST				(0x1 << 1)
 #define CH0_TEST				(0x1 << 0)
 
-/* EXYNOS_DP_AUX_CH_STA */
+/* ANALOGIX_DP_AUX_CH_STA */
 #define AUX_BUSY				(0x1 << 4)
 #define AUX_STATUS_MASK				(0xf << 0)
 
-/* EXYNOS_DP_AUX_CH_DEFER_CTL */
+/* ANALOGIX_DP_AUX_CH_DEFER_CTL */
 #define DEFER_CTRL_EN				(0x1 << 7)
 #define DEFER_COUNT(x)				(((x) & 0x7f) << 0)
 
-/* EXYNOS_DP_AUX_RX_COMM */
+/* ANALOGIX_DP_AUX_RX_COMM */
 #define AUX_RX_COMM_I2C_DEFER			(0x2 << 2)
 #define AUX_RX_COMM_AUX_DEFER			(0x2 << 0)
 
-/* EXYNOS_DP_BUFFER_DATA_CTL */
+/* ANALOGIX_DP_BUFFER_DATA_CTL */
 #define BUF_CLR					(0x1 << 7)
 #define BUF_DATA_COUNT(x)			(((x) & 0x1f) << 0)
 
-/* EXYNOS_DP_AUX_CH_CTL_1 */
+/* ANALOGIX_DP_AUX_CH_CTL_1 */
 #define AUX_LENGTH(x)				(((x - 1) & 0xf) << 4)
 #define AUX_TX_COMM_MASK			(0xf << 0)
 #define AUX_TX_COMM_DP_TRANSACTION		(0x1 << 3)
@@ -340,20 +352,20 @@
 #define AUX_TX_COMM_WRITE			(0x0 << 0)
 #define AUX_TX_COMM_READ			(0x1 << 0)
 
-/* EXYNOS_DP_AUX_ADDR_7_0 */
+/* ANALOGIX_DP_AUX_ADDR_7_0 */
 #define AUX_ADDR_7_0(x)				(((x) >> 0) & 0xff)
 
-/* EXYNOS_DP_AUX_ADDR_15_8 */
+/* ANALOGIX_DP_AUX_ADDR_15_8 */
 #define AUX_ADDR_15_8(x)			(((x) >> 8) & 0xff)
 
-/* EXYNOS_DP_AUX_ADDR_19_16 */
+/* ANALOGIX_DP_AUX_ADDR_19_16 */
 #define AUX_ADDR_19_16(x)			(((x) >> 16) & 0x0f)
 
-/* EXYNOS_DP_AUX_CH_CTL_2 */
+/* ANALOGIX_DP_AUX_CH_CTL_2 */
 #define ADDR_ONLY				(0x1 << 1)
 #define AUX_EN					(0x1 << 0)
 
-/* EXYNOS_DP_SOC_GENERAL_CTL */
+/* ANALOGIX_DP_SOC_GENERAL_CTL */
 #define AUDIO_MODE_SPDIF_MODE			(0x1 << 8)
 #define AUDIO_MODE_MASTER_MODE			(0x0 << 8)
 #define MASTER_VIDEO_INTERLACE_EN		(0x1 << 4)
@@ -363,4 +375,4 @@
 #define VIDEO_MODE_SLAVE_MODE			(0x1 << 0)
 #define VIDEO_MODE_MASTER_MODE			(0x0 << 0)
 
-#endif /* _EXYNOS_DP_REG_H */
+#endif /* _ANALOGIX_DP_REG_H */

drivers/gpu/drm/exynos/Kconfig

@@ -71,8 +71,9 @@ config DRM_EXYNOS_DSI
 	  This enables support for Exynos MIPI-DSI device.
 
 config DRM_EXYNOS_DP
-	bool "Display Port"
+	bool "EXYNOS specific extensions for Analogix DP driver"
 	depends on DRM_EXYNOS_FIMD || DRM_EXYNOS7_DECON
+	select DRM_ANALOGIX_DP
 	default DRM_EXYNOS
 	select DRM_PANEL
 	help

drivers/gpu/drm/exynos/Makefile

@@ -12,7 +12,7 @@ exynosdrm-$(CONFIG_DRM_EXYNOS5433_DECON)	+= exynos5433_drm_decon.o
 exynosdrm-$(CONFIG_DRM_EXYNOS7_DECON)	+= exynos7_drm_decon.o
 exynosdrm-$(CONFIG_DRM_EXYNOS_DPI)	+= exynos_drm_dpi.o
 exynosdrm-$(CONFIG_DRM_EXYNOS_DSI)	+= exynos_drm_dsi.o
-exynosdrm-$(CONFIG_DRM_EXYNOS_DP)	+= exynos_dp_core.o exynos_dp_reg.o
+exynosdrm-$(CONFIG_DRM_EXYNOS_DP)	+= exynos_dp.o
 exynosdrm-$(CONFIG_DRM_EXYNOS_MIXER)	+= exynos_mixer.o
 exynosdrm-$(CONFIG_DRM_EXYNOS_HDMI)	+= exynos_hdmi.o
 exynosdrm-$(CONFIG_DRM_EXYNOS_VIDI)	+= exynos_drm_vidi.o

drivers/gpu/drm/exynos/exynos_dp.c

+/*
+ * Samsung SoC DP (Display Port) interface driver.
+ *
+ * Copyright (C) 2012 Samsung Electronics Co., Ltd.
+ * Author: Jingoo Han <jg1.han@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/of_graph.h>
+#include <linux/component.h>
+#include <video/of_display_timing.h>
+#include <video/of_videomode.h>
+#include <video/videomode.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_panel.h>
+
+#include <drm/bridge/analogix_dp.h>
+#include <drm/exynos_drm.h>
+
+#include "exynos_drm_crtc.h"
+
+#define to_dp(nm)	container_of(nm, struct exynos_dp_device, nm)
+
+struct exynos_dp_device {
+	struct drm_encoder         encoder;
+	struct drm_connector       connector;
+	struct drm_bridge          *ptn_bridge;
+	struct drm_device          *drm_dev;
+	struct device              *dev;
+
+	struct videomode           vm;
+	struct analogix_dp_plat_data plat_data;
+};
+
+int exynos_dp_crtc_clock_enable(struct analogix_dp_plat_data *plat_data,
+				bool enable)
+{
+	struct exynos_dp_device *dp = to_dp(plat_data);
+	struct drm_encoder *encoder = &dp->encoder;
+	struct exynos_drm_crtc *crtc;
+
+	if (!encoder)
+		return -1;
+
+	crtc = to_exynos_crtc(encoder->crtc);
+	if (crtc && crtc->ops && crtc->ops->clock_enable)
+		crtc->ops->clock_enable(crtc, enable);
+
+	return 0;
+}
+
+static int exynos_dp_poweron(struct analogix_dp_plat_data *plat_data)
+{
+	return exynos_dp_crtc_clock_enable(plat_data, true);
+}
+
+static int exynos_dp_poweroff(struct analogix_dp_plat_data *plat_data)
+{
+	return exynos_dp_crtc_clock_enable(plat_data, false);
+}
+
+static int exynos_dp_get_modes(struct analogix_dp_plat_data *plat_data)
+{
+	struct exynos_dp_device *dp = to_dp(plat_data);
+	struct drm_connector *connector = &dp->connector;
+	struct drm_display_mode *mode;
+	int num_modes = 0;
+
+	if (dp->plat_data.panel)
+		return num_modes;
+
+	mode = drm_mode_create(connector->dev);
+	if (!mode) {
+		DRM_ERROR("failed to create a new display mode.\n");
+		return num_modes;
+	}
+
+	drm_display_mode_from_videomode(&dp->vm, mode);
+	connector->display_info.width_mm = mode->width_mm;
+	connector->display_info.height_mm = mode->height_mm;
+
+	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+	drm_mode_set_name(mode);
+	drm_mode_probed_add(connector, mode);
+
+	return num_modes + 1;
+}
+
+static int exynos_dp_bridge_attach(struct analogix_dp_plat_data *plat_data,
+				   struct drm_bridge *bridge,
+				   struct drm_connector *connector)
+{
+	struct exynos_dp_device *dp = to_dp(plat_data);
+	struct drm_encoder *encoder = &dp->encoder;
+	int ret;
+
+	drm_connector_register(connector);
+
+	/* Pre-empt DP connector creation if there's a bridge */
+	if (dp->ptn_bridge) {
+		bridge->next = dp->ptn_bridge;
+		dp->ptn_bridge->encoder = encoder;
+		ret = drm_bridge_attach(encoder->dev, dp->ptn_bridge);
+		if (ret) {
+			DRM_ERROR("Failed to attach bridge to drm\n");
+			bridge->next = NULL;
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static void exynos_dp_mode_set(struct drm_encoder *encoder,
+			       struct drm_display_mode *mode,
+			       struct drm_display_mode *adjusted_mode)
+{
+}
+
+static void exynos_dp_nop(struct drm_encoder *encoder)
+{
+	/* do nothing */
+}
+
+static const struct drm_encoder_helper_funcs exynos_dp_encoder_helper_funcs = {
+	.mode_set = exynos_dp_mode_set,
+	.enable = exynos_dp_nop,
+	.disable = exynos_dp_nop,
+};
+
+static const struct drm_encoder_funcs exynos_dp_encoder_funcs = {
+	.destroy = drm_encoder_cleanup,
+};
+
+static int exynos_dp_dt_parse_panel(struct exynos_dp_device *dp)
+{
+	int ret;
+
+	ret = of_get_videomode(dp->dev->of_node, &dp->vm, OF_USE_NATIVE_MODE);
+	if (ret) {
+		DRM_ERROR("failed: of_get_videomode() : %d\n", ret);
+		return ret;
+	}
+	return 0;
+}
+
+static int exynos_dp_bind(struct device *dev, struct device *master, void *data)
+{
+	struct exynos_dp_device *dp = dev_get_drvdata(dev);
+	struct drm_encoder *encoder = &dp->encoder;
+	struct drm_device *drm_dev = data;
+	int pipe, ret;
+
+	/*
+	 * Just like the probe function said, we don't need the
+	 * device drvrate anymore, we should leave the charge to
+	 * analogix dp driver, set the device drvdata to NULL.
+	 */
+	dev_set_drvdata(dev, NULL);
+
+	dp->dev = dev;
+	dp->drm_dev = drm_dev;
+
+	dp->plat_data.dev_type = EXYNOS_DP;
+	dp->plat_data.power_on = exynos_dp_poweron;
+	dp->plat_data.power_off = exynos_dp_poweroff;
+	dp->plat_data.attach = exynos_dp_bridge_attach;
+	dp->plat_data.get_modes = exynos_dp_get_modes;
+
+	if (!dp->plat_data.panel && !dp->ptn_bridge) {
+		ret = exynos_dp_dt_parse_panel(dp);
+		if (ret)
+			return ret;
+	}
+
+	pipe = exynos_drm_crtc_get_pipe_from_type(drm_dev,
+						  EXYNOS_DISPLAY_TYPE_LCD);
+	if (pipe < 0)
+		return pipe;
+
+	encoder->possible_crtcs = 1 << pipe;
+
+	DRM_DEBUG_KMS("possible_crtcs = 0x%x\n", encoder->possible_crtcs);
+
+	drm_encoder_init(drm_dev, encoder, &exynos_dp_encoder_funcs,
+			 DRM_MODE_ENCODER_TMDS, NULL);
+
+	drm_encoder_helper_add(encoder, &exynos_dp_encoder_helper_funcs);
+
+	dp->plat_data.encoder = encoder;
+
+	return analogix_dp_bind(dev, dp->drm_dev, &dp->plat_data);
+}
+
+static void exynos_dp_unbind(struct device *dev, struct device *master,
+			     void *data)
+{
+	return analogix_dp_unbind(dev, master, data);
+}
+
+static const struct component_ops exynos_dp_ops = {
+	.bind	= exynos_dp_bind,
+	.unbind	= exynos_dp_unbind,
+};
+
+static int exynos_dp_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = NULL, *endpoint = NULL;
+	struct exynos_dp_device *dp;
+
+	dp = devm_kzalloc(&pdev->dev, sizeof(struct exynos_dp_device),
+			  GFP_KERNEL);
+	if (!dp)
+		return -ENOMEM;
+
+	/*
+	 * We just use the drvdata until driver run into component
+	 * add function, and then we would set drvdata to null, so
+	 * that analogix dp driver would take charge of the drvdata.
+	 */
+	platform_set_drvdata(pdev, dp);
+
+	/* This is for the backward compatibility. */
+	np = of_parse_phandle(dev->of_node, "panel", 0);
+	if (np) {
+		dp->plat_data.panel = of_drm_find_panel(np);
+		of_node_put(np);
+		if (!dp->plat_data.panel)
+			return -EPROBE_DEFER;
+		goto out;
+	}
+
+	endpoint = of_graph_get_next_endpoint(dev->of_node, NULL);
+	if (endpoint) {
+		np = of_graph_get_remote_port_parent(endpoint);
+		if (np) {
+			/* The remote port can be either a panel or a bridge */
+			dp->plat_data.panel = of_drm_find_panel(np);
+			if (!dp->plat_data.panel) {
+				dp->ptn_bridge = of_drm_find_bridge(np);
+				if (!dp->ptn_bridge) {
+					of_node_put(np);
+					return -EPROBE_DEFER;
+				}
+			}
+			of_node_put(np);
+		} else {
+			DRM_ERROR("no remote endpoint device node found.\n");
+			return -EINVAL;
+		}
+	} else {
+		DRM_ERROR("no port endpoint subnode found.\n");
+		return -EINVAL;
+	}
+
+out:
+	return component_add(&pdev->dev, &exynos_dp_ops);
+}
+
+static int exynos_dp_remove(struct platform_device *pdev)
+{
+	component_del(&pdev->dev, &exynos_dp_ops);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int exynos_dp_suspend(struct device *dev)
+{
+	return analogix_dp_suspend(dev);
+}
+
+static int exynos_dp_resume(struct device *dev)
+{
+	return analogix_dp_resume(dev);
+}
+#endif
+
+static const struct dev_pm_ops exynos_dp_pm_ops = {
+	SET_RUNTIME_PM_OPS(exynos_dp_suspend, exynos_dp_resume, NULL)
+};
+
+static const struct of_device_id exynos_dp_match[] = {
+	{ .compatible = "samsung,exynos5-dp" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, exynos_dp_match);
+
+struct platform_driver dp_driver = {
+	.probe		= exynos_dp_probe,
+	.remove		= exynos_dp_remove,
+	.driver		= {
+		.name	= "exynos-dp",
+		.owner	= THIS_MODULE,
+		.pm	= &exynos_dp_pm_ops,
+		.of_match_table = exynos_dp_match,
+	},
+};
+
+MODULE_AUTHOR("Jingoo Han <jg1.han@samsung.com>");
+MODULE_DESCRIPTION("Samsung Specific Analogix-DP Driver Extension");
+MODULE_LICENSE("GPL v2");

drivers/gpu/drm/rockchip/Kconfig

@@ -16,6 +16,15 @@ config DRM_ROCKCHIP
 	  2D or 3D acceleration; acceleration is performed by other
 	  IP found on the SoC.
 
+config ROCKCHIP_ANALOGIX_DP
+	tristate "Rockchip specific extensions for Analogix DP driver"
+	depends on DRM_ROCKCHIP
+	select DRM_ANALOGIX_DP
+	help
+	  This selects support for Rockchip SoC specific extensions
+	  for the Analogix Core DP driver. If you want to enable DP
+	  on RK3288 based SoC, you should selet this option.
+
 config ROCKCHIP_DW_HDMI
         tristate "Rockchip specific extensions for Synopsys DW HDMI"
         depends on DRM_ROCKCHIP

drivers/gpu/drm/rockchip/Makefile

@@ -6,6 +6,7 @@ rockchipdrm-y := rockchip_drm_drv.o rockchip_drm_fb.o \
 		rockchip_drm_gem.o rockchip_drm_vop.o
 rockchipdrm-$(CONFIG_DRM_FBDEV_EMULATION) += rockchip_drm_fbdev.o
 
+obj-$(CONFIG_ROCKCHIP_ANALOGIX_DP) += analogix_dp-rockchip.o
 obj-$(CONFIG_ROCKCHIP_DW_HDMI) += dw_hdmi-rockchip.o
 obj-$(CONFIG_ROCKCHIP_DW_MIPI_DSI) += dw-mipi-dsi.o
 obj-$(CONFIG_ROCKCHIP_INNO_HDMI) += inno_hdmi.o

include/drm/bridge/analogix_dp.h

+/*
+ * Analogix DP (Display Port) Core interface driver.
+ *
+ * Copyright (C) 2015 Rockchip Electronics Co., Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+#ifndef _ANALOGIX_DP_H_
+#define _ANALOGIX_DP_H_
+
+#include <drm/drm_crtc.h>
+
+enum analogix_dp_devtype {
+	EXYNOS_DP,
+	RK3288_DP,
+};
+
+struct analogix_dp_plat_data {
+	enum analogix_dp_devtype dev_type;
+	struct drm_panel *panel;
+	struct drm_encoder *encoder;
+	struct drm_connector *connector;
+
+	int (*power_on)(struct analogix_dp_plat_data *);
+	int (*power_off)(struct analogix_dp_plat_data *);
+	int (*attach)(struct analogix_dp_plat_data *, struct drm_bridge *,
+		      struct drm_connector *);
+	int (*get_modes)(struct analogix_dp_plat_data *);
+};
+
+int analogix_dp_resume(struct device *dev);
+int analogix_dp_suspend(struct device *dev);
+
+int analogix_dp_bind(struct device *dev, struct drm_device *drm_dev,
+		     struct analogix_dp_plat_data *plat_data);
+void analogix_dp_unbind(struct device *dev, struct device *master, void *data);
+
+#endif /* _ANALOGIX_DP_H_ */