提交 c218bca7 编写于 作者: C Catalin Marinas

arm64: Relax the kernel cache requirements for boot

With system caches for the host OS or architected caches for guest OS we
cannot easily guarantee that there are no dirty or stale cache lines for
the areas of memory written by the kernel during boot with the MMU off
(therefore non-cacheable accesses).

This patch adds the necessary cache maintenance during boot and relaxes
the booting requirements.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
上级 35a86976
......@@ -111,8 +111,14 @@ Before jumping into the kernel, the following conditions must be met:
- Caches, MMUs
The MMU must be off.
Instruction cache may be on or off.
Data cache must be off and invalidated.
External caches (if present) must be configured and disabled.
The address range corresponding to the loaded kernel image must be
cleaned to the PoC. In the presence of a system cache or other
coherent masters with caches enabled, this will typically require
cache maintenance by VA rather than set/way operations.
System caches which respect the architected cache maintenance by VA
operations must be configured and may be enabled.
System caches which do not respect architected cache maintenance by VA
operations (not recommended) must be configured and disabled.
- Architected timers
CNTFRQ must be programmed with the timer frequency and CNTVOFF must
......
......@@ -26,6 +26,7 @@
#include <asm/assembler.h>
#include <asm/ptrace.h>
#include <asm/asm-offsets.h>
#include <asm/cache.h>
#include <asm/cputype.h>
#include <asm/memory.h>
#include <asm/thread_info.h>
......@@ -229,7 +230,11 @@ ENTRY(set_cpu_boot_mode_flag)
cmp w20, #BOOT_CPU_MODE_EL2
b.ne 1f
add x1, x1, #4
1: str w20, [x1] // This CPU has booted in EL1
1: dc cvac, x1 // Clean potentially dirty cache line
dsb sy
str w20, [x1] // This CPU has booted in EL1
dc civac, x1 // Clean&invalidate potentially stale cache line
dsb sy
ret
ENDPROC(set_cpu_boot_mode_flag)
......@@ -240,8 +245,9 @@ ENDPROC(set_cpu_boot_mode_flag)
* This is not in .bss, because we set it sufficiently early that the boot-time
* zeroing of .bss would clobber it.
*/
.pushsection .data
.pushsection .data..cacheline_aligned
ENTRY(__boot_cpu_mode)
.align L1_CACHE_SHIFT
.long BOOT_CPU_MODE_EL2
.long 0
.popsection
......@@ -408,6 +414,15 @@ ENDPROC(__calc_phys_offset)
*/
__create_page_tables:
pgtbl x25, x26, x24 // idmap_pg_dir and swapper_pg_dir addresses
mov x27, lr
/*
* Invalidate the idmap and swapper page tables to avoid potential
* dirty cache lines being evicted.
*/
mov x0, x25
add x1, x26, #SWAPPER_DIR_SIZE
bl __inval_cache_range
/*
* Clear the idmap and swapper page tables.
......@@ -470,6 +485,17 @@ __create_page_tables:
add x0, x26, #2 * PAGE_SIZE // section table address
create_pgd_entry x26, x0, x5, x6, x7
#endif
/*
* Since the page tables have been populated with non-cacheable
* accesses (MMU disabled), invalidate the idmap and swapper page
* tables again to remove any speculatively loaded cache lines.
*/
mov x0, x25
add x1, x26, #SWAPPER_DIR_SIZE
bl __inval_cache_range
mov lr, x27
ret
ENDPROC(__create_page_tables)
.ltorg
......
......@@ -167,6 +167,14 @@ ENTRY(__flush_dcache_area)
ret
ENDPROC(__flush_dcache_area)
/*
* __inval_cache_range(start, end)
* - start - start address of region
* - end - end address of region
*/
ENTRY(__inval_cache_range)
/* FALLTHROUGH */
/*
* __dma_inv_range(start, end)
* - start - virtual start address of region
......@@ -183,6 +191,7 @@ __dma_inv_range:
b.lo 1b
dsb sy
ret
ENDPROC(__inval_cache_range)
ENDPROC(__dma_inv_range)
/*
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册