提交 c11d7162 编写于 作者: L Linus Torvalds

Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC cleanups from Kevin Hilman:
 "A relatively small setup of cleanups this time around, and similar to
  last time the bulk of it is removal of legacy board support:

   - OMAP: removal of legacy (non-DT) booting for several platforms

   - i.MX: remove some legacy board files"

* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
  ARM: fix EFM32 build breakage caused by cpu_resume_arm
  ARM: 8389/1: Add cpu_resume_arm() for firmwares that resume in ARM state
  ARM: v7 setup function should invalidate L1 cache
  mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
  ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
  ARM: OMAP2+: Constify irq_domain_ops
  ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
  ARM: at91: remove useless Makefile.boot
  ARM: at91: remove at91rm9200_sdramc.h
  ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h
  ARM: at91/pm: use the atmel-mc syscon defines
  pcmcia: at91_cf: Use syscon to configure the MC/smc
  ARM: at91: declare the at91rm9200 memory controller as a syscon
  mfd: syscon: Add Atmel MC (Memory Controller) registers definition
  ARM: at91: drop sam9_smc.c
  ata: at91: use syscon to configure the smc
  ARM: ux500: delete static resource defines
  ARM: ux500: rename ux500_map_io
  ARM: ux500: look up PRCMU resource from DT
  ARM: ux500: kill off L2CC static map
  ...
......@@ -98,7 +98,7 @@ Example:
};
RAMC SDRAM/DDR Controller required properties:
- compatible: Should be "atmel,at91rm9200-sdramc",
- compatible: Should be "atmel,at91rm9200-sdramc", "syscon"
"atmel,at91sam9260-sdramc",
"atmel,at91sam9g45-ddramc",
"atmel,sama5d3-ddramc",
......
......@@ -29,7 +29,7 @@ Example:
fuse@7000f800 {
compatible = "nvidia,tegra20-efuse";
reg = <0x7000F800 0x400>,
reg = <0x7000f800 0x400>,
<0x70000000 0x400>;
clocks = <&tegra_car TEGRA20_CLK_FUSE>;
clock-names = "fuse";
......
......@@ -92,7 +92,7 @@
};
ramc0: ramc@ffffff00 {
compatible = "atmel,at91rm9200-sdramc";
compatible = "atmel,at91rm9200-sdramc", "syscon";
reg = <0xffffff00 0x100>;
};
......
......@@ -70,7 +70,7 @@
broken-cd;
bypass-smu;
cap-mmc-highspeed;
supports-hs200-mode; /* 200 Mhz */
supports-hs200-mode; /* 200 MHz */
card-detect-delay = <200>;
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <0 4>;
......
......@@ -66,7 +66,7 @@
otg_drv_vbus: pinmux_otg_drv_vbus {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50Mhz_clk.usb0_drvvbus */
OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50MHz_clk.usb0_drvvbus */
>;
};
......
......@@ -300,7 +300,7 @@
apbmisc@0,70000800 {
compatible = "nvidia,tegra124-apbmisc", "nvidia,tegra20-apbmisc";
reg = <0x0 0x70000800 0x0 0x64>, /* Chip revision */
<0x0 0x7000E864 0x0 0x04>; /* Strapping options */
<0x0 0x7000e864 0x0 0x04>; /* Strapping options */
};
pinmux: pinmux@0,70000868 {
......
......@@ -563,7 +563,7 @@
fuse@7000f800 {
compatible = "nvidia,tegra20-efuse";
reg = <0x7000F800 0x400>;
reg = <0x7000f800 0x400>;
clocks = <&tegra_car TEGRA20_CLK_FUSE>;
clock-names = "fuse";
resets = <&tegra_car 39>;
......
......@@ -7,6 +7,7 @@ struct sleep_save_sp {
};
extern void cpu_resume(void);
extern void cpu_resume_arm(void);
extern int cpu_suspend(unsigned long, int (*)(unsigned long));
#endif
......@@ -118,6 +118,16 @@ ENDPROC(cpu_resume_after_mmu)
.text
.align
#ifdef CONFIG_MMU
.arm
ENTRY(cpu_resume_arm)
THUMB( adr r9, BSYM(1f) ) @ Kernel is entered in ARM.
THUMB( bx r9 ) @ If this is a Thumb-2 kernel,
THUMB( .thumb ) @ switch to Thumb now.
THUMB(1: )
#endif
ENTRY(cpu_resume)
ARM_BE8(setend be) @ ensure we are in BE mode
#ifdef CONFIG_ARM_VIRT_EXT
......@@ -150,6 +160,10 @@ THUMB( mov sp, r2 )
THUMB( bx r3 )
ENDPROC(cpu_resume)
#ifdef CONFIG_MMU
ENDPROC(cpu_resume_arm)
#endif
.align 2
_sleep_save_sp:
.long sleep_save_sp - .
......
#
# Makefile for the linux kernel.
#
ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
asflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
obj-y := soc.o
obj-$(CONFIG_SOC_AT91SAM9) += sam9_smc.o
# CPU-specific support
obj-$(CONFIG_SOC_AT91RM9200) += at91rm9200.o
obj-$(CONFIG_SOC_AT91SAM9) += at91sam9.o
......
# Note: the following conditions must always be true:
# ZRELADDR == virt_to_phys(TEXTADDR)
# PARAMS_PHYS must be within 4MB of ZRELADDR
# INITRD_PHYS must be in RAM
zreladdr-y += 0x20008000
params_phys-y := 0x20000100
initrd_phys-y := 0x20410000
/*
* Header file for the Atmel RAM Controller
*
* Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
*
* Under GPLv2 only
*/
#ifndef __AT91_RAMC_H__
#define __AT91_RAMC_H__
#ifndef __ASSEMBLY__
extern void __iomem *at91_ramc_base[];
#define at91_ramc_read(id, field) \
__raw_readl(at91_ramc_base[id] + field)
#define at91_ramc_write(id, field, value) \
__raw_writel(value, at91_ramc_base[id] + field)
#else
.extern at91_ramc_base
#endif
#include <soc/at91/at91rm9200_sdramc.h>
#include <soc/at91/at91sam9_ddrsdr.h>
#include <soc/at91/at91sam9_sdramc.h>
#endif /* __AT91_RAMC_H__ */
/*
* arch/arm/mach-at91/include/mach/at91rm9200_mc.h
*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
*
* Memory Controllers (MC, EBI, SMC, SDRAMC, BFC) - System peripherals registers.
* Based on AT91RM9200 datasheet revision E.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#ifndef AT91RM9200_MC_H
#define AT91RM9200_MC_H
/* Memory Controller */
#define AT91_MC_RCR 0x00 /* MC Remap Control Register */
#define AT91_MC_RCB (1 << 0) /* Remap Command Bit */
#define AT91_MC_ASR 0x04 /* MC Abort Status Register */
#define AT91_MC_UNADD (1 << 0) /* Undefined Address Abort Status */
#define AT91_MC_MISADD (1 << 1) /* Misaligned Address Abort Status */
#define AT91_MC_ABTSZ (3 << 8) /* Abort Size Status */
#define AT91_MC_ABTSZ_BYTE (0 << 8)
#define AT91_MC_ABTSZ_HALFWORD (1 << 8)
#define AT91_MC_ABTSZ_WORD (2 << 8)
#define AT91_MC_ABTTYP (3 << 10) /* Abort Type Status */
#define AT91_MC_ABTTYP_DATAREAD (0 << 10)
#define AT91_MC_ABTTYP_DATAWRITE (1 << 10)
#define AT91_MC_ABTTYP_FETCH (2 << 10)
#define AT91_MC_MST0 (1 << 16) /* ARM920T Abort Source */
#define AT91_MC_MST1 (1 << 17) /* PDC Abort Source */
#define AT91_MC_MST2 (1 << 18) /* UHP Abort Source */
#define AT91_MC_MST3 (1 << 19) /* EMAC Abort Source */
#define AT91_MC_SVMST0 (1 << 24) /* Saved ARM920T Abort Source */
#define AT91_MC_SVMST1 (1 << 25) /* Saved PDC Abort Source */
#define AT91_MC_SVMST2 (1 << 26) /* Saved UHP Abort Source */
#define AT91_MC_SVMST3 (1 << 27) /* Saved EMAC Abort Source */
#define AT91_MC_AASR 0x08 /* MC Abort Address Status Register */
#define AT91_MC_MPR 0x0c /* MC Master Priority Register */
#define AT91_MPR_MSTP0 (7 << 0) /* ARM920T Priority */
#define AT91_MPR_MSTP1 (7 << 4) /* PDC Priority */
#define AT91_MPR_MSTP2 (7 << 8) /* UHP Priority */
#define AT91_MPR_MSTP3 (7 << 12) /* EMAC Priority */
/* External Bus Interface (EBI) registers */
#define AT91_EBI_CSA 0x60 /* Chip Select Assignment Register */
#define AT91_EBI_CS0A (1 << 0) /* Chip Select 0 Assignment */
#define AT91_EBI_CS0A_SMC (0 << 0)
#define AT91_EBI_CS0A_BFC (1 << 0)
#define AT91_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */
#define AT91_EBI_CS1A_SMC (0 << 1)
#define AT91_EBI_CS1A_SDRAMC (1 << 1)
#define AT91_EBI_CS3A (1 << 3) /* Chip Select 2 Assignment */
#define AT91_EBI_CS3A_SMC (0 << 3)
#define AT91_EBI_CS3A_SMC_SMARTMEDIA (1 << 3)
#define AT91_EBI_CS4A (1 << 4) /* Chip Select 3 Assignment */
#define AT91_EBI_CS4A_SMC (0 << 4)
#define AT91_EBI_CS4A_SMC_COMPACTFLASH (1 << 4)
#define AT91_EBI_CFGR (AT91_MC + 0x64) /* Configuration Register */
#define AT91_EBI_DBPUC (1 << 0) /* Data Bus Pull-Up Configuration */
/* Static Memory Controller (SMC) registers */
#define AT91_SMC_CSR(n) (0x70 + ((n) * 4)) /* SMC Chip Select Register */
#define AT91_SMC_NWS (0x7f << 0) /* Number of Wait States */
#define AT91_SMC_NWS_(x) ((x) << 0)
#define AT91_SMC_WSEN (1 << 7) /* Wait State Enable */
#define AT91_SMC_TDF (0xf << 8) /* Data Float Time */
#define AT91_SMC_TDF_(x) ((x) << 8)
#define AT91_SMC_BAT (1 << 12) /* Byte Access Type */
#define AT91_SMC_DBW (3 << 13) /* Data Bus Width */
#define AT91_SMC_DBW_16 (1 << 13)
#define AT91_SMC_DBW_8 (2 << 13)
#define AT91_SMC_DPR (1 << 15) /* Data Read Protocol */
#define AT91_SMC_ACSS (3 << 16) /* Address to Chip Select Setup */
#define AT91_SMC_ACSS_STD (0 << 16)
#define AT91_SMC_ACSS_1 (1 << 16)
#define AT91_SMC_ACSS_2 (2 << 16)
#define AT91_SMC_ACSS_3 (3 << 16)
#define AT91_SMC_RWSETUP (7 << 24) /* Read & Write Signal Time Setup */
#define AT91_SMC_RWSETUP_(x) ((x) << 24)
#define AT91_SMC_RWHOLD (7 << 28) /* Read & Write Signal Hold Time */
#define AT91_SMC_RWHOLD_(x) ((x) << 28)
/* Burst Flash Controller register */
#define AT91_BFC_MR 0xc0 /* Mode Register */
#define AT91_BFC_BFCOM (3 << 0) /* Burst Flash Controller Operating Mode */
#define AT91_BFC_BFCOM_DISABLED (0 << 0)
#define AT91_BFC_BFCOM_ASYNC (1 << 0)
#define AT91_BFC_BFCOM_BURST (2 << 0)
#define AT91_BFC_BFCC (3 << 2) /* Burst Flash Controller Clock */
#define AT91_BFC_BFCC_MCK (1 << 2)
#define AT91_BFC_BFCC_DIV2 (2 << 2)
#define AT91_BFC_BFCC_DIV4 (3 << 2)
#define AT91_BFC_AVL (0xf << 4) /* Address Valid Latency */
#define AT91_BFC_PAGES (7 << 8) /* Page Size */
#define AT91_BFC_PAGES_NO_PAGE (0 << 8)
#define AT91_BFC_PAGES_16 (1 << 8)
#define AT91_BFC_PAGES_32 (2 << 8)
#define AT91_BFC_PAGES_64 (3 << 8)
#define AT91_BFC_PAGES_128 (4 << 8)
#define AT91_BFC_PAGES_256 (5 << 8)
#define AT91_BFC_PAGES_512 (6 << 8)
#define AT91_BFC_PAGES_1024 (7 << 8)
#define AT91_BFC_OEL (3 << 12) /* Output Enable Latency */
#define AT91_BFC_BAAEN (1 << 16) /* Burst Address Advance Enable */
#define AT91_BFC_BFOEH (1 << 17) /* Burst Flash Output Enable Handling */
#define AT91_BFC_MUXEN (1 << 18) /* Multiplexed Bus Enable */
#define AT91_BFC_RDYEN (1 << 19) /* Ready Enable Mode */
#endif
/*
* arch/arm/mach-at91/include/mach/at91sam9_smc.h
*
* Copyright (C) 2007 Andrew Victor
* Copyright (C) 2007 Atmel Corporation.
*
* Static Memory Controllers (SMC) - System peripherals registers.
* Based on AT91SAM9261 datasheet revision D.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#ifndef AT91SAM9_SMC_H
#define AT91SAM9_SMC_H
#ifndef __ASSEMBLY__
struct sam9_smc_config {
/* Setup register */
u8 ncs_read_setup;
u8 nrd_setup;
u8 ncs_write_setup;
u8 nwe_setup;
/* Pulse register */
u8 ncs_read_pulse;
u8 nrd_pulse;
u8 ncs_write_pulse;
u8 nwe_pulse;
/* Cycle register */
u16 read_cycle;
u16 write_cycle;
/* Mode register */
u32 mode;
u8 tdf_cycles:4;
};
extern void sam9_smc_configure(int id, int cs, struct sam9_smc_config *config);
extern void sam9_smc_read(int id, int cs, struct sam9_smc_config *config);
extern void sam9_smc_read_mode(int id, int cs, struct sam9_smc_config *config);
extern void sam9_smc_write_mode(int id, int cs, struct sam9_smc_config *config);
#endif
#define AT91_SMC_SETUP 0x00 /* Setup Register for CS n */
#define AT91_SMC_NWESETUP (0x3f << 0) /* NWE Setup Length */
#define AT91_SMC_NWESETUP_(x) ((x) << 0)
#define AT91_SMC_NCS_WRSETUP (0x3f << 8) /* NCS Setup Length in Write Access */
#define AT91_SMC_NCS_WRSETUP_(x) ((x) << 8)
#define AT91_SMC_NRDSETUP (0x3f << 16) /* NRD Setup Length */
#define AT91_SMC_NRDSETUP_(x) ((x) << 16)
#define AT91_SMC_NCS_RDSETUP (0x3f << 24) /* NCS Setup Length in Read Access */
#define AT91_SMC_NCS_RDSETUP_(x) ((x) << 24)
#define AT91_SMC_PULSE 0x04 /* Pulse Register for CS n */
#define AT91_SMC_NWEPULSE (0x7f << 0) /* NWE Pulse Length */
#define AT91_SMC_NWEPULSE_(x) ((x) << 0)
#define AT91_SMC_NCS_WRPULSE (0x7f << 8) /* NCS Pulse Length in Write Access */
#define AT91_SMC_NCS_WRPULSE_(x)((x) << 8)
#define AT91_SMC_NRDPULSE (0x7f << 16) /* NRD Pulse Length */
#define AT91_SMC_NRDPULSE_(x) ((x) << 16)
#define AT91_SMC_NCS_RDPULSE (0x7f << 24) /* NCS Pulse Length in Read Access */
#define AT91_SMC_NCS_RDPULSE_(x)((x) << 24)
#define AT91_SMC_CYCLE 0x08 /* Cycle Register for CS n */
#define AT91_SMC_NWECYCLE (0x1ff << 0 ) /* Total Write Cycle Length */
#define AT91_SMC_NWECYCLE_(x) ((x) << 0)
#define AT91_SMC_NRDCYCLE (0x1ff << 16) /* Total Read Cycle Length */
#define AT91_SMC_NRDCYCLE_(x) ((x) << 16)
#define AT91_SMC_MODE 0x0c /* Mode Register for CS n */
#define AT91_SMC_READMODE (1 << 0) /* Read Mode */
#define AT91_SMC_WRITEMODE (1 << 1) /* Write Mode */
#define AT91_SMC_EXNWMODE (3 << 4) /* NWAIT Mode */
#define AT91_SMC_EXNWMODE_DISABLE (0 << 4)
#define AT91_SMC_EXNWMODE_FROZEN (2 << 4)
#define AT91_SMC_EXNWMODE_READY (3 << 4)
#define AT91_SMC_BAT (1 << 8) /* Byte Access Type */
#define AT91_SMC_BAT_SELECT (0 << 8)
#define AT91_SMC_BAT_WRITE (1 << 8)
#define AT91_SMC_DBW (3 << 12) /* Data Bus Width */
#define AT91_SMC_DBW_8 (0 << 12)
#define AT91_SMC_DBW_16 (1 << 12)
#define AT91_SMC_DBW_32 (2 << 12)
#define AT91_SMC_TDF (0xf << 16) /* Data Float Time. */
#define AT91_SMC_TDF_(x) ((x) << 16)
#define AT91_SMC_TDFMODE (1 << 20) /* TDF Optimization - Enabled */
#define AT91_SMC_PMEN (1 << 24) /* Page Mode Enabled */
#define AT91_SMC_PS (3 << 28) /* Page Size */
#define AT91_SMC_PS_4 (0 << 28)
#define AT91_SMC_PS_8 (1 << 28)
#define AT91_SMC_PS_16 (2 << 28)
#define AT91_SMC_PS_32 (3 << 28)
#endif
......@@ -233,7 +233,7 @@ static void at91_pm_set_standby(void (*at91_standby)(void))
*/
static void at91rm9200_standby(void)
{
u32 lpr = at91_ramc_read(0, AT91RM9200_SDRAMC_LPR);
u32 lpr = at91_ramc_read(0, AT91_MC_SDRAMC_LPR);
asm volatile(
"b 1f\n\t"
......@@ -244,8 +244,8 @@ static void at91rm9200_standby(void)
" mcr p15, 0, %0, c7, c0, 4\n\t"
" str %5, [%1, %2]"
:
: "r" (0), "r" (at91_ramc_base[0]), "r" (AT91RM9200_SDRAMC_LPR),
"r" (1), "r" (AT91RM9200_SDRAMC_SRR),
: "r" (0), "r" (at91_ramc_base[0]), "r" (AT91_MC_SDRAMC_LPR),
"r" (1), "r" (AT91_MC_SDRAMC_SRR),
"r" (lpr));
}
......@@ -414,7 +414,7 @@ void __init at91rm9200_pm_init(void)
/*
* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh.
*/
at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
at91_ramc_write(0, AT91_MC_SDRAMC_LPR, 0);
at91_pm_data.uhp_udp_mask = AT91RM9200_PMC_UHP | AT91RM9200_PMC_UDP;
at91_pm_data.memctrl = AT91_MEMCTRL_MC;
......
......@@ -13,7 +13,19 @@
#include <asm/proc-fns.h>
#include <mach/at91_ramc.h>
#include <linux/mfd/syscon/atmel-mc.h>
#include <soc/at91/at91sam9_ddrsdr.h>
#include <soc/at91/at91sam9_sdramc.h>
#ifndef __ASSEMBLY__
extern void __iomem *at91_ramc_base[];
#define at91_ramc_read(id, field) \
__raw_readl(at91_ramc_base[id] + field)
#define at91_ramc_write(id, field, value) \
__raw_writel(value, at91_ramc_base[id] + field)
#endif
#define AT91_MEMCTRL_MC 0
#define AT91_MEMCTRL_SDRAMC 1
......
......@@ -13,7 +13,6 @@
*/
#include <linux/linkage.h>
#include <linux/clk/at91_pmc.h>
#include <mach/at91_ramc.h>
#include "pm.h"
#define SRAMC_SELF_FRESH_ACTIVE 0x01
......@@ -216,7 +215,7 @@ ENTRY(at91_sramc_self_refresh)
/* Active SDRAM self-refresh mode */
mov r3, #1
str r3, [r2, #AT91RM9200_SDRAMC_SRR]
str r3, [r2, #AT91_MC_SDRAMC_SRR]
b exit_sramc_sf
ddrc_sf:
......
/*
* linux/arch/arm/mach-at91/sam9_smc.c
*
* Copyright (C) 2008 Andrew Victor
* Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/module.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <mach/at91sam9_smc.h>
#include "sam9_smc.h"
#define AT91_SMC_CS(id, n) (smc_base_addr[id] + ((n) * 0x10))
static void __iomem *smc_base_addr[2];
static void sam9_smc_cs_write_mode(void __iomem *base,
struct sam9_smc_config *config)
{
__raw_writel(config->mode
| AT91_SMC_TDF_(config->tdf_cycles),
base + AT91_SMC_MODE);
}
void sam9_smc_write_mode(int id, int cs,
struct sam9_smc_config *config)
{
sam9_smc_cs_write_mode(AT91_SMC_CS(id, cs), config);
}
EXPORT_SYMBOL_GPL(sam9_smc_write_mode);
static void sam9_smc_cs_configure(void __iomem *base,
struct sam9_smc_config *config)
{
/* Setup register */
__raw_writel(AT91_SMC_NWESETUP_(config->nwe_setup)
| AT91_SMC_NCS_WRSETUP_(config->ncs_write_setup)
| AT91_SMC_NRDSETUP_(config->nrd_setup)
| AT91_SMC_NCS_RDSETUP_(config->ncs_read_setup),
base + AT91_SMC_SETUP);
/* Pulse register */
__raw_writel(AT91_SMC_NWEPULSE_(config->nwe_pulse)
| AT91_SMC_NCS_WRPULSE_(config->ncs_write_pulse)
| AT91_SMC_NRDPULSE_(config->nrd_pulse)
| AT91_SMC_NCS_RDPULSE_(config->ncs_read_pulse),
base + AT91_SMC_PULSE);
/* Cycle register */
__raw_writel(AT91_SMC_NWECYCLE_(config->write_cycle)
| AT91_SMC_NRDCYCLE_(config->read_cycle),
base + AT91_SMC_CYCLE);
/* Mode register */
sam9_smc_cs_write_mode(base, config);
}
void sam9_smc_configure(int id, int cs,
struct sam9_smc_config *config)
{
sam9_smc_cs_configure(AT91_SMC_CS(id, cs), config);
}
EXPORT_SYMBOL_GPL(sam9_smc_configure);
static void sam9_smc_cs_read_mode(void __iomem *base,
struct sam9_smc_config *config)
{
u32 val = __raw_readl(base + AT91_SMC_MODE);
config->mode = (val & ~AT91_SMC_NWECYCLE);
config->tdf_cycles = (val & AT91_SMC_NWECYCLE) >> 16 ;
}
void sam9_smc_read_mode(int id, int cs,
struct sam9_smc_config *config)
{
sam9_smc_cs_read_mode(AT91_SMC_CS(id, cs), config);
}
EXPORT_SYMBOL_GPL(sam9_smc_read_mode);
static void sam9_smc_cs_read(void __iomem *base,
struct sam9_smc_config *config)
{
u32 val;
/* Setup register */
val = __raw_readl(base + AT91_SMC_SETUP);
config->nwe_setup = val & AT91_SMC_NWESETUP;
config->ncs_write_setup = (val & AT91_SMC_NCS_WRSETUP) >> 8;
config->nrd_setup = (val & AT91_SMC_NRDSETUP) >> 16;
config->ncs_read_setup = (val & AT91_SMC_NCS_RDSETUP) >> 24;
/* Pulse register */
val = __raw_readl(base + AT91_SMC_PULSE);
config->nwe_pulse = val & AT91_SMC_NWEPULSE;
config->ncs_write_pulse = (val & AT91_SMC_NCS_WRPULSE) >> 8;
config->nrd_pulse = (val & AT91_SMC_NRDPULSE) >> 16;
config->ncs_read_pulse = (val & AT91_SMC_NCS_RDPULSE) >> 24;
/* Cycle register */
val = __raw_readl(base + AT91_SMC_CYCLE);
config->write_cycle = val & AT91_SMC_NWECYCLE;
config->read_cycle = (val & AT91_SMC_NRDCYCLE) >> 16;
/* Mode register */
sam9_smc_cs_read_mode(base, config);
}
void sam9_smc_read(int id, int cs, struct sam9_smc_config *config)
{
sam9_smc_cs_read(AT91_SMC_CS(id, cs), config);
}
void __init at91sam9_ioremap_smc(int id, u32 addr)
{
if (id > 1) {
pr_warn("%s: id > 2\n", __func__);
return;
}
smc_base_addr[id] = ioremap(addr, 512);
if (!smc_base_addr[id])
pr_warn("Impossible to ioremap smc.%d 0x%x\n", id, addr);
}
/*
* linux/arch/arm/mach-at91/sam9_smc.
*
* Copyright (C) 2008 Andrew Victor
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
extern void __init at91sam9_ioremap_smc(int id, u32 addr);
......@@ -43,5 +43,5 @@ obj-$(CONFIG_ARCH_BCM_63XX) := bcm63xx.o
ifeq ($(CONFIG_ARCH_BRCMSTB),y)
CFLAGS_platsmp-brcmstb.o += -march=armv7-a
obj-y += brcmstb.o
obj-$(CONFIG_SMP) += headsmp-brcmstb.o platsmp-brcmstb.o
obj-$(CONFIG_SMP) += platsmp-brcmstb.o
endif
/*
* Copyright (C) 2013-2014 Broadcom Corporation
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation version 2.
*
* This program is distributed "as is" WITHOUT ANY WARRANTY of any
* kind, whether express or implied; without even the implied warranty
* of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#ifndef __BRCMSTB_H__
#define __BRCMSTB_H__
void brcmstb_secondary_startup(void);
#endif /* __BRCMSTB_H__ */
/*
* SMP boot code for secondary CPUs
* Based on arch/arm/mach-tegra/headsmp.S
*
* Copyright (C) 2010 NVIDIA, Inc.
* Copyright (C) 2013-2014 Broadcom Corporation
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation version 2.
*
* This program is distributed "as is" WITHOUT ANY WARRANTY of any
* kind, whether express or implied; without even the implied warranty
* of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <asm/assembler.h>
#include <linux/linkage.h>
#include <linux/init.h>
.section ".text.head", "ax"
ENTRY(brcmstb_secondary_startup)
/*
* Ensure CPU is in a sane state by disabling all IRQs and switching
* into SVC mode.
*/
setmode PSR_I_BIT | PSR_F_BIT | SVC_MODE, r0
bl v7_invalidate_l1
b secondary_startup
ENDPROC(brcmstb_secondary_startup)
......@@ -30,8 +30,6 @@
#include <asm/mach-types.h>
#include <asm/smp_plat.h>
#include "brcmstb.h"
enum {
ZONE_MAN_CLKEN_MASK = BIT(0),
ZONE_MAN_RESET_CNTL_MASK = BIT(1),
......@@ -153,7 +151,7 @@ static void brcmstb_cpu_boot(u32 cpu)
* Set the reset vector to point to the secondary_startup
* routine
*/
cpu_set_boot_addr(cpu, virt_to_phys(brcmstb_secondary_startup));
cpu_set_boot_addr(cpu, virt_to_phys(secondary_startup));
/* Unhalt the cpu */
cpu_rst_cfg_set(cpu, 0);
......
......@@ -12,12 +12,6 @@
#include <linux/init.h>
#include <asm/assembler.h>
ENTRY(berlin_secondary_startup)
ARM_BE8(setend be)
bl v7_invalidate_l1
b secondary_startup
ENDPROC(berlin_secondary_startup)
/*
* If the following instruction is set in the reset exception vector, CPUs
* will fetch the value of the software reset address vector when being
......
......@@ -22,7 +22,6 @@
#define RESET_VECT 0x00
#define SW_RESET_ADDR 0x94
extern void berlin_secondary_startup(void);
extern u32 boot_inst;
static void __iomem *cpu_ctrl;
......@@ -85,7 +84,7 @@ static void __init berlin_smp_prepare_cpus(unsigned int max_cpus)
* Write the secondary startup address into the SW reset address
* vector. This is used by boot_inst.
*/
writel(virt_to_phys(berlin_secondary_startup), vectors_base + SW_RESET_ADDR);
writel(virt_to_phys(secondary_startup), vectors_base + SW_RESET_ADDR);
iounmap(vectors_base);
unmap_scu:
......
......@@ -36,7 +36,7 @@ extern void __iomem *da8xx_syscfg1_base;
/*
* If the DA850/OMAP-L138/AM18x SoC on board is of a higher speed grade
* (than the regular 300Mhz variant), the board code should set this up
* (than the regular 300MHz variant), the board code should set this up
* with the supported speed before calling da850_register_cpufreq().
*/
extern unsigned int da850_max_speed;
......
......@@ -6,4 +6,4 @@ CFLAGS_platmcpm.o := -march=armv7-a
obj-y += hisilicon.o
obj-$(CONFIG_MCPM) += platmcpm.o
obj-$(CONFIG_SMP) += platsmp.o hotplug.o headsmp.o
obj-$(CONFIG_SMP) += platsmp.o hotplug.o
......@@ -12,7 +12,6 @@ extern void hi3xxx_cpu_die(unsigned int cpu);
extern int hi3xxx_cpu_kill(unsigned int cpu);
extern void hi3xxx_set_cpu(int cpu, bool enable);
extern void hisi_secondary_startup(void);
extern struct smp_operations hix5hd2_smp_ops;
extern void hix5hd2_set_cpu(int cpu, bool enable);
extern void hix5hd2_cpu_die(unsigned int cpu);
......
/*
* Copyright (c) 2014 Hisilicon Limited.
* Copyright (c) 2014 Linaro Ltd.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/linkage.h>
#include <linux/init.h>
__CPUINIT
ENTRY(hisi_secondary_startup)
bl v7_invalidate_l1
b secondary_startup
......@@ -118,7 +118,7 @@ static int hix5hd2_boot_secondary(unsigned int cpu, struct task_struct *idle)
{
phys_addr_t jumpaddr;
jumpaddr = virt_to_phys(hisi_secondary_startup);
jumpaddr = virt_to_phys(secondary_startup);
hix5hd2_set_scu_boot_addr(HIX5HD2_BOOT_ADDRESS, jumpaddr);
hix5hd2_set_cpu(cpu, true);
arch_send_wakeup_ipi_mask(cpumask_of(cpu));
......@@ -156,7 +156,7 @@ static int hip01_boot_secondary(unsigned int cpu, struct task_struct *idle)
struct device_node *node;
jumpaddr = virt_to_phys(hisi_secondary_startup);
jumpaddr = virt_to_phys(secondary_startup);
hip01_set_boot_addr(HIP01_BOOT_ADDRESS, jumpaddr);
node = of_find_compatible_node(NULL, NULL, "hisilicon,hip01-sysctrl");
......
......@@ -444,40 +444,6 @@ config MACH_MX35_3DS
Include support for MX35PDK platform. This includes specific
configurations for the board and its peripherals.
config MACH_EUKREA_CPUIMX35SD
bool "Support Eukrea CPUIMX35 Platform"
select IMX_HAVE_PLATFORM_FLEXCAN
select IMX_HAVE_PLATFORM_FSL_USB2_UDC
select IMX_HAVE_PLATFORM_IMX2_WDT
select IMX_HAVE_PLATFORM_IMX_I2C
select IMX_HAVE_PLATFORM_IMX_UART
select IMX_HAVE_PLATFORM_MXC_EHCI
select IMX_HAVE_PLATFORM_MXC_NAND
select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
select USB_ULPI_VIEWPORT if USB_ULPI
select SOC_IMX35
help
Include support for Eukrea CPUIMX35 platform. This includes
specific configurations for the board and its peripherals.
choice
prompt "Baseboard"
depends on MACH_EUKREA_CPUIMX35SD
default MACH_EUKREA_MBIMXSD35_BASEBOARD
config MACH_EUKREA_MBIMXSD35_BASEBOARD
bool "Eukrea MBIMXSD development board"
select IMX_HAVE_PLATFORM_GPIO_KEYS
select IMX_HAVE_PLATFORM_IMX_SSI
select IMX_HAVE_PLATFORM_IPU_CORE
select IMX_HAVE_PLATFORM_SPI_IMX
select LEDS_GPIO_REGISTER
help
This adds board specific devices that can be found on Eukrea's
MBIMXSD evaluation board.
endchoice
config MACH_VPR200
bool "Support VPR200 platform"
select IMX_HAVE_PLATFORM_FSL_USB2_UDC
......
......@@ -73,8 +73,6 @@ obj-$(CONFIG_MACH_IMX31_DT) += imx31-dt.o
# i.MX35 based machines
obj-$(CONFIG_MACH_PCM043) += mach-pcm043.o
obj-$(CONFIG_MACH_MX35_3DS) += mach-mx35_3ds.o
obj-$(CONFIG_MACH_EUKREA_CPUIMX35SD) += mach-cpuimx35.o
obj-$(CONFIG_MACH_EUKREA_MBIMXSD35_BASEBOARD) += eukrea_mbimxsd35-baseboard.o
obj-$(CONFIG_MACH_VPR200) += mach-vpr200.o
obj-$(CONFIG_MACH_IMX35_DT) += imx35-dt.o
......
......@@ -216,7 +216,7 @@ static void __init imx6sx_clocks_init(struct device_node *ccm_node)
clks[IMX6SX_CLK_USBPHY1_GATE] = imx_clk_gate("usbphy1_gate", "dummy", base + 0x10, 6);
clks[IMX6SX_CLK_USBPHY2_GATE] = imx_clk_gate("usbphy2_gate", "dummy", base + 0x20, 6);
/* FIXME 100Mhz is used for pcie ref for all imx6 pcie, excepted imx6q */
/* FIXME 100MHz is used for pcie ref for all imx6 pcie, excepted imx6q */
clks[IMX6SX_CLK_PCIE_REF] = imx_clk_fixed_factor("pcie_ref", "pll6_enet", 1, 5);
clks[IMX6SX_CLK_PCIE_REF_125M] = imx_clk_gate("pcie_ref_125m", "pcie_ref", base + 0xe0, 19);
......@@ -520,7 +520,7 @@ static void __init imx6sx_clocks_init(struct device_node *ccm_node)
pr_err("Failed to set pcie parent clk.\n");
/*
* Init enet system AHB clock, set to 200Mhz
* Init enet system AHB clock, set to 200MHz
* pll2_pfd2_396m-> ENET_PODF-> ENET_AHB
*/
clk_set_parent(clks[IMX6SX_CLK_ENET_PRE_SEL], clks[IMX6SX_CLK_PLL2_PFD2]);
......
/*
* Copyright (C) 2010 Eric Benard - eric@eukrea.com
*
* Based on pcm970-baseboard.c which is :
* Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version 2
* of the License, or (at your option) any later version.
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301, USA.
*/
#include <linux/types.h>
#include <linux/init.h>
#include <linux/gpio.h>
#include <linux/interrupt.h>
#include <linux/leds.h>
#include <linux/platform_device.h>
#include <linux/input.h>
#include <linux/spi/spi.h>
#include <video/platform_lcd.h>
#include <linux/i2c.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <asm/mach/map.h>
#include "common.h"
#include "devices-imx35.h"
#include "hardware.h"
#include "iomux-mx35.h"
static const struct fb_videomode fb_modedb[] = {
{
.name = "CMO-QVGA",
.refresh = 60,
.xres = 320,
.yres = 240,
.pixclock = KHZ2PICOS(6500),
.left_margin = 68,
.right_margin = 20,
.upper_margin = 15,
.lower_margin = 4,
.hsync_len = 30,
.vsync_len = 3,
.sync = 0,
.vmode = FB_VMODE_NONINTERLACED,
.flag = 0,
},
{
.name = "DVI-VGA",
.refresh = 60,
.xres = 640,
.yres = 480,
.pixclock = 32000,
.left_margin = 100,
.right_margin = 100,
.upper_margin = 7,
.lower_margin = 100,
.hsync_len = 7,
.vsync_len = 7,
.sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT |
FB_SYNC_OE_ACT_HIGH | FB_SYNC_CLK_INVERT,
.vmode = FB_VMODE_NONINTERLACED,
.flag = 0,
},
{
.name = "DVI-SVGA",
.refresh = 60,
.xres = 800,
.yres = 600,
.pixclock = 25000,
.left_margin = 75,
.right_margin = 75,
.upper_margin = 7,
.lower_margin = 75,
.hsync_len = 7,
.vsync_len = 7,
.sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT |
FB_SYNC_OE_ACT_HIGH | FB_SYNC_CLK_INVERT,
.vmode = FB_VMODE_NONINTERLACED,
.flag = 0,
},
};
static struct mx3fb_platform_data mx3fb_pdata __initdata = {
.name = "CMO-QVGA",
.mode = fb_modedb,
.num_modes = ARRAY_SIZE(fb_modedb),
};
static const iomux_v3_cfg_t eukrea_mbimxsd_pads[] __initconst = {
/* LCD */
MX35_PAD_LD0__IPU_DISPB_DAT_0,
MX35_PAD_LD1__IPU_DISPB_DAT_1,
MX35_PAD_LD2__IPU_DISPB_DAT_2,
MX35_PAD_LD3__IPU_DISPB_DAT_3,
MX35_PAD_LD4__IPU_DISPB_DAT_4,
MX35_PAD_LD5__IPU_DISPB_DAT_5,
MX35_PAD_LD6__IPU_DISPB_DAT_6,
MX35_PAD_LD7__IPU_DISPB_DAT_7,
MX35_PAD_LD8__IPU_DISPB_DAT_8,
MX35_PAD_LD9__IPU_DISPB_DAT_9,
MX35_PAD_LD10__IPU_DISPB_DAT_10,
MX35_PAD_LD11__IPU_DISPB_DAT_11,
MX35_PAD_LD12__IPU_DISPB_DAT_12,
MX35_PAD_LD13__IPU_DISPB_DAT_13,
MX35_PAD_LD14__IPU_DISPB_DAT_14,
MX35_PAD_LD15__IPU_DISPB_DAT_15,
MX35_PAD_LD16__IPU_DISPB_DAT_16,
MX35_PAD_LD17__IPU_DISPB_DAT_17,
MX35_PAD_D3_HSYNC__IPU_DISPB_D3_HSYNC,
MX35_PAD_D3_FPSHIFT__IPU_DISPB_D3_CLK,
MX35_PAD_D3_DRDY__IPU_DISPB_D3_DRDY,
MX35_PAD_D3_VSYNC__IPU_DISPB_D3_VSYNC,
/* Backlight */
MX35_PAD_CONTRAST__IPU_DISPB_CONTR,
/* LCD_PWR */
MX35_PAD_D3_CLS__GPIO1_4,
/* LED */
MX35_PAD_LD23__GPIO3_29,
/* SWITCH */
MX35_PAD_LD19__GPIO3_25,
/* UART2 */
MX35_PAD_CTS2__UART2_CTS,
MX35_PAD_RTS2__UART2_RTS,
MX35_PAD_TXD2__UART2_TXD_MUX,
MX35_PAD_RXD2__UART2_RXD_MUX,
/* I2S */
MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS,
MX35_PAD_STXD4__AUDMUX_AUD4_TXD,
MX35_PAD_SRXD4__AUDMUX_AUD4_RXD,
MX35_PAD_SCK4__AUDMUX_AUD4_TXC,
/* CAN2 */
MX35_PAD_TX5_RX0__CAN2_TXCAN,
MX35_PAD_TX4_RX1__CAN2_RXCAN,
/* SDCARD */
MX35_PAD_SD1_CMD__ESDHC1_CMD,
MX35_PAD_SD1_CLK__ESDHC1_CLK,
MX35_PAD_SD1_DATA0__ESDHC1_DAT0,
MX35_PAD_SD1_DATA1__ESDHC1_DAT1,
MX35_PAD_SD1_DATA2__ESDHC1_DAT2,
MX35_PAD_SD1_DATA3__ESDHC1_DAT3,
/* SD1 CD */
MX35_PAD_LD18__GPIO3_24,
/* SPI */
MX35_PAD_CSPI1_MOSI__CSPI1_MOSI,
MX35_PAD_CSPI1_MISO__CSPI1_MISO,
MX35_PAD_CSPI1_SS0__GPIO1_18,
MX35_PAD_CSPI1_SS1__GPIO1_19,
MX35_PAD_CSPI1_SCLK__CSPI1_SCLK,
MX35_PAD_CSPI1_SPI_RDY__GPIO3_5,
};
#define GPIO_LED1 IMX_GPIO_NR(3, 29)
#define GPIO_SWITCH1 IMX_GPIO_NR(3, 25)
#define GPIO_LCDPWR IMX_GPIO_NR(1, 4)
#define GPIO_SD1CD IMX_GPIO_NR(3, 24)
#define GPIO_SPI1_SS0 IMX_GPIO_NR(1, 18)
#define GPIO_SPI1_SS1 IMX_GPIO_NR(1, 19)
#define GPIO_SPI1_IRQ IMX_GPIO_NR(3, 5)
static void eukrea_mbimxsd_lcd_power_set(struct plat_lcd_data *pd,
unsigned int power)
{
if (power)
gpio_direction_output(GPIO_LCDPWR, 1);
else
gpio_direction_output(GPIO_LCDPWR, 0);
}
static struct plat_lcd_data eukrea_mbimxsd_lcd_power_data = {
.set_power = eukrea_mbimxsd_lcd_power_set,
};
static struct platform_device eukrea_mbimxsd_lcd_powerdev = {
.name = "platform-lcd",
.dev.platform_data = &eukrea_mbimxsd_lcd_power_data,
};
static struct gpio_led eukrea_mbimxsd_leds[] = {
{
.name = "led1",
.default_trigger = "heartbeat",
.active_low = 1,
.gpio = GPIO_LED1,
},
};
static const struct gpio_led_platform_data
eukrea_mbimxsd_led_info __initconst = {
.leds = eukrea_mbimxsd_leds,
.num_leds = ARRAY_SIZE(eukrea_mbimxsd_leds),
};
static struct gpio_keys_button eukrea_mbimxsd_gpio_buttons[] = {
{
.gpio = GPIO_SWITCH1,
.code = BTN_0,
.desc = "BP1",
.active_low = 1,
.wakeup = 1,
},
};
static const struct gpio_keys_platform_data
eukrea_mbimxsd_button_data __initconst = {
.buttons = eukrea_mbimxsd_gpio_buttons,
.nbuttons = ARRAY_SIZE(eukrea_mbimxsd_gpio_buttons),
};
static struct platform_device *platform_devices[] __initdata = {
&eukrea_mbimxsd_lcd_powerdev,
};
static const struct imxuart_platform_data uart_pdata __initconst = {
.flags = IMXUART_HAVE_RTSCTS,
};
static struct i2c_board_info eukrea_mbimxsd_i2c_devices[] = {
{
I2C_BOARD_INFO("tlv320aic23", 0x1a),
},
};
static const
struct imx_ssi_platform_data eukrea_mbimxsd_ssi_pdata __initconst = {
.flags = IMX_SSI_SYN | IMX_SSI_NET | IMX_SSI_USE_I2S_SLAVE,
};
static struct esdhc_platform_data sd1_pdata = {
.cd_gpio = GPIO_SD1CD,
.cd_type = ESDHC_CD_GPIO,
.wp_type = ESDHC_WP_NONE,
};
static struct spi_board_info eukrea_mbimxsd35_spi_board_info[] __initdata = {
{
.modalias = "spidev",
.max_speed_hz = 20000000,
.bus_num = 0,
.chip_select = 0,
.mode = SPI_MODE_0,
},
{
.modalias = "spidev",
.max_speed_hz = 20000000,
.bus_num = 0,
.chip_select = 1,
.mode = SPI_MODE_0,
},
};
static int eukrea_mbimxsd35_spi_cs[] = {GPIO_SPI1_SS0, GPIO_SPI1_SS1};
static const struct spi_imx_master eukrea_mbimxsd35_spi0_data __initconst = {
.chipselect = eukrea_mbimxsd35_spi_cs,
.num_chipselect = ARRAY_SIZE(eukrea_mbimxsd35_spi_cs),
};
/*
* system init for baseboard usage. Will be called by cpuimx35 init.
*
* Add platform devices present on this baseboard and init
* them from CPU side as far as required to use them later on
*/
void __init eukrea_mbimxsd35_baseboard_init(void)
{
if (mxc_iomux_v3_setup_multiple_pads(eukrea_mbimxsd_pads,
ARRAY_SIZE(eukrea_mbimxsd_pads)))
printk(KERN_ERR "error setting mbimxsd pads !\n");
imx35_add_imx_uart1(&uart_pdata);
imx35_add_ipu_core();
imx35_add_mx3_sdc_fb(&mx3fb_pdata);
imx35_add_imx_ssi(0, &eukrea_mbimxsd_ssi_pdata);
imx35_add_flexcan1();
imx35_add_sdhci_esdhc_imx(0, &sd1_pdata);
gpio_request(GPIO_LED1, "LED1");
gpio_direction_output(GPIO_LED1, 1);
gpio_free(GPIO_LED1);
gpio_request(GPIO_SWITCH1, "SWITCH1");
gpio_direction_input(GPIO_SWITCH1);
gpio_free(GPIO_SWITCH1);
gpio_request(GPIO_LCDPWR, "LCDPWR");
gpio_direction_output(GPIO_LCDPWR, 1);
i2c_register_board_info(0, eukrea_mbimxsd_i2c_devices,
ARRAY_SIZE(eukrea_mbimxsd_i2c_devices));
gpio_request(GPIO_SPI1_IRQ, "SPI1_IRQ");
gpio_direction_input(GPIO_SPI1_IRQ);
gpio_free(GPIO_SPI1_IRQ);
imx35_add_spi_imx0(&eukrea_mbimxsd35_spi0_data);
spi_register_board_info(eukrea_mbimxsd35_spi_board_info,
ARRAY_SIZE(eukrea_mbimxsd35_spi_board_info));
platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
gpio_led_register_device(-1, &eukrea_mbimxsd_led_info);
imx_add_gpio_keys(&eukrea_mbimxsd_button_data);
imx_add_platform_device("eukrea_tlv320", 0, NULL, 0, NULL, 0);
}
......@@ -474,7 +474,6 @@ static const struct of_device_id imx_gpc_dt_ids[] = {
static struct platform_driver imx_gpc_driver = {
.driver = {
.name = "imx-gpc",
.owner = THIS_MODULE,
.of_match_table = imx_gpc_dt_ids,
},
.probe = imx_gpc_probe,
......
......@@ -25,7 +25,6 @@ diag_reg_offset:
.endm
ENTRY(v7_secondary_startup)
bl v7_invalidate_l1
set_diag_reg
b secondary_startup
ENDPROC(v7_secondary_startup)
/*
* Copyright (C) 2010 Eric Benard - eric@eukrea.com
* Copyright (C) 2009 Sascha Hauer, Pengutronix
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/types.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/mtd/physmap.h>
#include <linux/memory.h>
#include <linux/gpio.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/i2c.h>
#include <linux/i2c/tsc2007.h>
#include <linux/usb/otg.h>
#include <linux/usb/ulpi.h>
#include <linux/i2c-gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <asm/mach/map.h>
#include "common.h"
#include "devices-imx35.h"
#include "ehci.h"
#include "eukrea-baseboards.h"
#include "hardware.h"
#include "iomux-mx35.h"
static const struct imxuart_platform_data uart_pdata __initconst = {
.flags = IMXUART_HAVE_RTSCTS,
};
static const struct imxi2c_platform_data
eukrea_cpuimx35_i2c0_data __initconst = {
.bitrate = 100000,
};
#define TSC2007_IRQGPIO IMX_GPIO_NR(3, 2)
static int tsc2007_get_pendown_state(struct device *dev)
{
return !gpio_get_value(TSC2007_IRQGPIO);
}
static struct tsc2007_platform_data tsc2007_info = {
.model = 2007,
.x_plate_ohms = 180,
.get_pendown_state = tsc2007_get_pendown_state,
};
static struct i2c_board_info eukrea_cpuimx35_i2c_devices[] = {
{
I2C_BOARD_INFO("pcf8563", 0x51),
}, {
I2C_BOARD_INFO("tsc2007", 0x48),
.platform_data = &tsc2007_info,
/* irq number is run-time assigned */
},
};
static const iomux_v3_cfg_t eukrea_cpuimx35_pads[] __initconst = {
/* UART1 */
MX35_PAD_CTS1__UART1_CTS,
MX35_PAD_RTS1__UART1_RTS,
MX35_PAD_TXD1__UART1_TXD_MUX,
MX35_PAD_RXD1__UART1_RXD_MUX,
/* FEC */
MX35_PAD_FEC_TX_CLK__FEC_TX_CLK,
MX35_PAD_FEC_RX_CLK__FEC_RX_CLK,
MX35_PAD_FEC_RX_DV__FEC_RX_DV,
MX35_PAD_FEC_COL__FEC_COL,
MX35_PAD_FEC_RDATA0__FEC_RDATA_0,
MX35_PAD_FEC_TDATA0__FEC_TDATA_0,
MX35_PAD_FEC_TX_EN__FEC_TX_EN,
MX35_PAD_FEC_MDC__FEC_MDC,
MX35_PAD_FEC_MDIO__FEC_MDIO,
MX35_PAD_FEC_TX_ERR__FEC_TX_ERR,
MX35_PAD_FEC_RX_ERR__FEC_RX_ERR,
MX35_PAD_FEC_CRS__FEC_CRS,
MX35_PAD_FEC_RDATA1__FEC_RDATA_1,
MX35_PAD_FEC_TDATA1__FEC_TDATA_1,
MX35_PAD_FEC_RDATA2__FEC_RDATA_2,
MX35_PAD_FEC_TDATA2__FEC_TDATA_2,
MX35_PAD_FEC_RDATA3__FEC_RDATA_3,
MX35_PAD_FEC_TDATA3__FEC_TDATA_3,
/* I2C1 */
MX35_PAD_I2C1_CLK__I2C1_SCL,
MX35_PAD_I2C1_DAT__I2C1_SDA,
/* TSC2007 IRQ */
MX35_PAD_ATA_DA2__GPIO3_2,
};
static const struct mxc_nand_platform_data
eukrea_cpuimx35_nand_board_info __initconst = {
.width = 1,
.hw_ecc = 1,
.flash_bbt = 1,
};
static int eukrea_cpuimx35_otg_init(struct platform_device *pdev)
{
return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
}
static const struct mxc_usbh_platform_data otg_pdata __initconst = {
.init = eukrea_cpuimx35_otg_init,
.portsc = MXC_EHCI_MODE_UTMI,
};
static int eukrea_cpuimx35_usbh1_init(struct platform_device *pdev)
{
return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_SINGLE_UNI |
MXC_EHCI_INTERNAL_PHY | MXC_EHCI_IPPUE_DOWN);
}
static const struct mxc_usbh_platform_data usbh1_pdata __initconst = {
.init = eukrea_cpuimx35_usbh1_init,
.portsc = MXC_EHCI_MODE_SERIAL,
};
static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
.operating_mode = FSL_USB2_DR_DEVICE,
.phy_mode = FSL_USB2_PHY_UTMI,
.workaround = FLS_USB2_WORKAROUND_ENGCM09152,
};
static bool otg_mode_host __initdata;
static int __init eukrea_cpuimx35_otg_mode(char *options)
{
if (!strcmp(options, "host"))
otg_mode_host = true;
else if (!strcmp(options, "device"))
otg_mode_host = false;
else
pr_info("otg_mode neither \"host\" nor \"device\". "
"Defaulting to device\n");
return 1;
}
__setup("otg_mode=", eukrea_cpuimx35_otg_mode);
/*
* Board specific initialization.
*/
static void __init eukrea_cpuimx35_init(void)
{
imx35_soc_init();
mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx35_pads,
ARRAY_SIZE(eukrea_cpuimx35_pads));
imx35_add_fec(NULL);
imx35_add_imx2_wdt();
imx35_add_imx_uart0(&uart_pdata);
imx35_add_mxc_nand(&eukrea_cpuimx35_nand_board_info);
eukrea_cpuimx35_i2c_devices[1].irq = gpio_to_irq(TSC2007_IRQGPIO);
i2c_register_board_info(0, eukrea_cpuimx35_i2c_devices,
ARRAY_SIZE(eukrea_cpuimx35_i2c_devices));
imx35_add_imx_i2c0(&eukrea_cpuimx35_i2c0_data);
if (otg_mode_host)
imx35_add_mxc_ehci_otg(&otg_pdata);
else
imx35_add_fsl_usb2_udc(&otg_device_pdata);
imx35_add_mxc_ehci_hs(&usbh1_pdata);
#ifdef CONFIG_MACH_EUKREA_MBIMXSD35_BASEBOARD
eukrea_mbimxsd35_baseboard_init();
#endif
}
static void __init eukrea_cpuimx35_timer_init(void)
{
mx35_clocks_init();
}
MACHINE_START(EUKREA_CPUIMX35SD, "Eukrea CPUIMX35")
/* Maintainer: Eukrea Electromatique */
.atag_offset = 0x100,
.map_io = mx35_map_io,
.init_early = imx35_init_early,
.init_irq = mx35_init_irq,
.init_time = eukrea_cpuimx35_timer_init,
.init_machine = eukrea_cpuimx35_init,
.restart = mxc_restart,
MACHINE_END
......@@ -42,7 +42,7 @@ static inline unsigned long iop13xx_core_freq(void)
case IOP13XX_CORE_FREQ_1200:
return 1200000000;
default:
printk("%s: warning unknown frequency, defaulting to 800Mhz\n",
printk("%s: warning unknown frequency, defaulting to 800MHz\n",
__func__);
}
......
......@@ -74,7 +74,7 @@ extern unsigned long ixp4xx_exp_bus_size;
/*
* Clock Speed Definitions.
*/
#define IXP4XX_PERIPHERAL_BUS_CLOCK (66) /* 66Mhzi APB BUS */
#define IXP4XX_PERIPHERAL_BUS_CLOCK (66) /* 66MHzi APB BUS */
#define IXP4XX_UART_XTAL 14745600
/*
......
......@@ -17,7 +17,7 @@
#include <asm/sizes.h>
/*
* Clocks are derived from MCLK, which is 25Mhz
* Clocks are derived from MCLK, which is 25MHz
*/
#define KS8695_CLOCK_RATE 25000000
......
......@@ -21,7 +21,6 @@
ENTRY(mvebu_cortex_a9_secondary_startup)
ARM_BE8(setend be)
bl v7_invalidate_l1
bl armada_38x_scu_power_up
b secondary_startup
ENDPROC(mvebu_cortex_a9_secondary_startup)
......@@ -171,12 +171,6 @@ config MACH_OMAP2_TUSB6010
depends on ARCH_OMAP2 && SOC_OMAP2420
default y if MACH_NOKIA_N8X0
config MACH_OMAP3_BEAGLE
bool "OMAP3 BEAGLE board"
depends on ARCH_OMAP3
default y
select OMAP_PACKAGE_CBB
config MACH_OMAP_LDP
bool "OMAP3 LDP board"
depends on ARCH_OMAP3
......@@ -203,12 +197,6 @@ config MACH_OMAP3_TORPEDO
for full description please see the products webpage at
http://www.logicpd.com/products/development-kits/zoom-omap35x-torpedo-development-kit
config MACH_OVERO
bool "Gumstix Overo board"
depends on ARCH_OMAP3
default y
select OMAP_PACKAGE_CBB
config MACH_OMAP3517EVM
bool "OMAP3517/ AM3517 EVM board"
depends on ARCH_OMAP3
......@@ -240,16 +228,6 @@ config MACH_NOKIA_RX51
default y
select OMAP_PACKAGE_CBB
config MACH_CM_T35
bool "CompuLab CM-T35/CM-T3730 modules"
depends on ARCH_OMAP3
default y
select MACH_CM_T3730
select OMAP_PACKAGE_CUS
config MACH_CM_T3730
bool
config OMAP3_SDRC_AC_TIMING
bool "Enable SDRC AC timing register changes"
depends on ARCH_OMAP3
......
......@@ -242,17 +242,14 @@ obj-$(CONFIG_SOC_OMAP2420) += msdi.o
# Specific board support
obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o pdata-quirks.o
obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board-omap3beagle.o
obj-$(CONFIG_MACH_OMAP_LDP) += board-ldp.o
obj-$(CONFIG_MACH_OMAP3530_LV_SOM) += board-omap3logic.o
obj-$(CONFIG_MACH_OMAP3_TORPEDO) += board-omap3logic.o
obj-$(CONFIG_MACH_OVERO) += board-overo.o
obj-$(CONFIG_MACH_OMAP3_PANDORA) += board-omap3pandora.o
obj-$(CONFIG_MACH_NOKIA_N8X0) += board-n8x0.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51.o sdram-nokia.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-peripherals.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-video.o
obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o
# Platform specific device init code
......
此差异已折叠。
/*
* linux/arch/arm/mach-omap2/board-omap3beagle.c
*
* Copyright (C) 2008 Texas Instruments
*
* Modified from mach-omap2/board-3430sdp.c
*
* Initial code: Syed Mohammed Khasim
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/leds.h>
#include <linux/pwm.h>
#include <linux/leds_pwm.h>
#include <linux/gpio.h>
#include <linux/input.h>
#include <linux/gpio_keys.h>
#include <linux/pm_opp.h>
#include <linux/cpu.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>
#include <linux/mmc/host.h>
#include <linux/usb/phy.h>
#include <linux/regulator/machine.h>
#include <linux/i2c/twl.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
#include <video/omapdss.h>
#include <video/omap-panel-data.h>
#include <linux/platform_data/mtd-nand-omap2.h>
#include "common.h"
#include "omap_device.h"
#include "gpmc.h"
#include "soc.h"
#include "mux.h"
#include "hsmmc.h"
#include "pm.h"
#include "board-flash.h"
#include "common-board-devices.h"
#define NAND_CS 0
static struct pwm_lookup pwm_lookup[] = {
/* LEDB -> PMU_STAT */
PWM_LOOKUP("twl-pwmled", 1, "leds_pwm", "beagleboard::pmu_stat",
7812500, PWM_POLARITY_NORMAL),
};
static struct led_pwm pwm_leds[] = {
{
.name = "beagleboard::pmu_stat",
.max_brightness = 127,
.pwm_period_ns = 7812500,
},
};
static struct led_pwm_platform_data pwm_data = {
.num_leds = ARRAY_SIZE(pwm_leds),
.leds = pwm_leds,
};
static struct platform_device leds_pwm = {
.name = "leds_pwm",
.id = -1,
.dev = {
.platform_data = &pwm_data,
},
};
/*
* OMAP3 Beagle revision
* Run time detection of Beagle revision is done by reading GPIO.
* GPIO ID -
* AXBX = GPIO173, GPIO172, GPIO171: 1 1 1
* C1_3 = GPIO173, GPIO172, GPIO171: 1 1 0
* C4 = GPIO173, GPIO172, GPIO171: 1 0 1
* XMA/XMB = GPIO173, GPIO172, GPIO171: 0 0 0
* XMC = GPIO173, GPIO172, GPIO171: 0 1 0
*/
enum {
OMAP3BEAGLE_BOARD_UNKN = 0,
OMAP3BEAGLE_BOARD_AXBX,
OMAP3BEAGLE_BOARD_C1_3,
OMAP3BEAGLE_BOARD_C4,
OMAP3BEAGLE_BOARD_XM,
OMAP3BEAGLE_BOARD_XMC,
};
static u8 omap3_beagle_version;
/*
* Board-specific configuration
* Defaults to BeagleBoard-xMC
*/
static struct {
int mmc1_gpio_wp;
bool usb_pwr_level; /* 0 - Active Low, 1 - Active High */
int dvi_pd_gpio;
int usr_button_gpio;
int mmc_caps;
} beagle_config = {
.mmc1_gpio_wp = -EINVAL,
.usb_pwr_level = 0,
.dvi_pd_gpio = -EINVAL,
.usr_button_gpio = 4,
.mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
};
static struct gpio omap3_beagle_rev_gpios[] __initdata = {
{ 171, GPIOF_IN, "rev_id_0" },
{ 172, GPIOF_IN, "rev_id_1" },
{ 173, GPIOF_IN, "rev_id_2" },
};
static void __init omap3_beagle_init_rev(void)
{
int ret;
u16 beagle_rev = 0;
omap_mux_init_gpio(171, OMAP_PIN_INPUT_PULLUP);
omap_mux_init_gpio(172, OMAP_PIN_INPUT_PULLUP);
omap_mux_init_gpio(173, OMAP_PIN_INPUT_PULLUP);
ret = gpio_request_array(omap3_beagle_rev_gpios,
ARRAY_SIZE(omap3_beagle_rev_gpios));
if (ret < 0) {
printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
return;
}
beagle_rev = gpio_get_value(171) | (gpio_get_value(172) << 1)
| (gpio_get_value(173) << 2);
gpio_free_array(omap3_beagle_rev_gpios,
ARRAY_SIZE(omap3_beagle_rev_gpios));
switch (beagle_rev) {
case 7:
printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
beagle_config.mmc1_gpio_wp = 29;
beagle_config.dvi_pd_gpio = 170;
beagle_config.usr_button_gpio = 7;
break;
case 6:
printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
beagle_config.mmc1_gpio_wp = 23;
beagle_config.dvi_pd_gpio = 170;
beagle_config.usr_button_gpio = 7;
break;
case 5:
printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
beagle_config.mmc1_gpio_wp = 23;
beagle_config.dvi_pd_gpio = 170;
beagle_config.usr_button_gpio = 7;
break;
case 0:
printk(KERN_INFO "OMAP3 Beagle Rev: xM Ax/Bx\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_XM;
beagle_config.usb_pwr_level = 1;
beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
break;
case 2:
printk(KERN_INFO "OMAP3 Beagle Rev: xM C\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_XMC;
beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
break;
default:
printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
}
}
static struct mtd_partition omap3beagle_nand_partitions[] = {
/* All the partition sizes are listed in terms of NAND block size */
{
.name = "X-Loader",
.offset = 0,
.size = 4 * NAND_BLOCK_SIZE,
.mask_flags = MTD_WRITEABLE, /* force read-only */
},
{
.name = "U-Boot",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
.size = 15 * NAND_BLOCK_SIZE,
.mask_flags = MTD_WRITEABLE, /* force read-only */
},
{
.name = "U-Boot Env",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
.size = 1 * NAND_BLOCK_SIZE,
},
{
.name = "Kernel",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
.size = 32 * NAND_BLOCK_SIZE,
},
{
.name = "File System",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
.size = MTDPART_SIZ_FULL,
},
};
/* DSS */
static struct connector_dvi_platform_data beagle_dvi_connector_pdata = {
.name = "dvi",
.source = "tfp410.0",
.i2c_bus_num = 3,
};
static struct platform_device beagle_dvi_connector_device = {
.name = "connector-dvi",
.id = 0,
.dev.platform_data = &beagle_dvi_connector_pdata,
};
static struct encoder_tfp410_platform_data beagle_tfp410_pdata = {
.name = "tfp410.0",
.source = "dpi.0",
.data_lines = 24,
.power_down_gpio = -1,
};
static struct platform_device beagle_tfp410_device = {
.name = "tfp410",
.id = 0,
.dev.platform_data = &beagle_tfp410_pdata,
};
static struct connector_atv_platform_data beagle_tv_pdata = {
.name = "tv",
.source = "venc.0",
.connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
.invert_polarity = false,
};
static struct platform_device beagle_tv_connector_device = {
.name = "connector-analog-tv",
.id = 0,
.dev.platform_data = &beagle_tv_pdata,
};
static struct omap_dss_board_info beagle_dss_data = {
.default_display_name = "dvi",
};
#include "sdram-micron-mt46h32m32lf-6.h"
static struct omap2_hsmmc_info mmc[] = {
{
.mmc = 1,
.caps = MMC_CAP_4_BIT_DATA,
.gpio_wp = -EINVAL,
.deferred = true,
},
{} /* Terminator */
};
static struct regulator_consumer_supply beagle_vmmc1_supply[] = {
REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
};
static struct regulator_consumer_supply beagle_vsim_supply[] = {
REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
};
static struct gpio_led gpio_leds[];
static struct usbhs_phy_data phy_data[] = {
{
.port = 2,
.reset_gpio = 147,
.vcc_gpio = -1, /* updated in beagle_twl_gpio_setup */
.vcc_polarity = 1, /* updated in beagle_twl_gpio_setup */
},
};
static int beagle_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
int r;
mmc[0].gpio_wp = beagle_config.mmc1_gpio_wp;
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
mmc[0].gpio_cd = gpio + 0;
omap_hsmmc_late_init(mmc);
/*
* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
* high / others active low)
* DVI reset GPIO is different between beagle revisions
*/
/* Valid for all -xM revisions */
if (cpu_is_omap3630()) {
/*
* gpio + 1 on Xm controls the TFP410's enable line (active low)
* gpio + 2 control varies depending on the board rev as below:
* P7/P8 revisions(prototype): Camera EN
* A2+ revisions (production): LDO (DVI, serial, led blocks)
*/
r = gpio_request_one(gpio + 1, GPIOF_OUT_INIT_LOW,
"nDVI_PWR_EN");
if (r)
pr_err("%s: unable to configure nDVI_PWR_EN\n",
__func__);
beagle_config.dvi_pd_gpio = gpio + 2;
} else {
/*
* REVISIT: need ehci-omap hooks for external VBUS
* power switch and overcurrent detect
*/
if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
pr_err("%s: unable to configure EHCI_nOC\n", __func__);
}
beagle_tfp410_pdata.power_down_gpio = beagle_config.dvi_pd_gpio;
platform_device_register(&beagle_tfp410_device);
platform_device_register(&beagle_dvi_connector_device);
platform_device_register(&beagle_tv_connector_device);
/* TWL4030_GPIO_MAX i.e. LED_GPO controls HS USB Port 2 power */
phy_data[0].vcc_gpio = gpio + TWL4030_GPIO_MAX;
phy_data[0].vcc_polarity = beagle_config.usb_pwr_level;
usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
return 0;
}
static struct twl4030_gpio_platform_data beagle_gpio_data = {
.use_leds = true,
.pullups = BIT(1),
.pulldowns = BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
| BIT(15) | BIT(16) | BIT(17),
.setup = beagle_twl_gpio_setup,
};
/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
static struct regulator_init_data beagle_vmmc1 = {
.constraints = {
.min_uV = 1850000,
.max_uV = 3150000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(beagle_vmmc1_supply),
.consumer_supplies = beagle_vmmc1_supply,
};
/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
static struct regulator_init_data beagle_vsim = {
.constraints = {
.min_uV = 1800000,
.max_uV = 3000000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(beagle_vsim_supply),
.consumer_supplies = beagle_vsim_supply,
};
static struct twl4030_platform_data beagle_twldata = {
/* platform_data for children goes here */
.gpio = &beagle_gpio_data,
.vmmc1 = &beagle_vmmc1,
.vsim = &beagle_vsim,
};
static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
{
I2C_BOARD_INFO("eeprom", 0x50),
},
};
static int __init omap3_beagle_i2c_init(void)
{
omap3_pmic_get_config(&beagle_twldata,
TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
TWL_COMMON_PDATA_AUDIO,
TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
beagle_twldata.vpll2->constraints.name = "VDVI";
omap3_pmic_init("twl4030", &beagle_twldata);
/* Bus 3 is attached to the DVI port where devices like the pico DLP
* projector don't work reliably with 400kHz */
omap_register_i2c_bus(3, 100, beagle_i2c_eeprom, ARRAY_SIZE(beagle_i2c_eeprom));
return 0;
}
static struct gpio_led gpio_leds[] = {
{
.name = "beagleboard::usr0",
.default_trigger = "heartbeat",
.gpio = 150,
},
{
.name = "beagleboard::usr1",
.default_trigger = "mmc0",
.gpio = 149,
},
};
static struct gpio_led_platform_data gpio_led_info = {
.leds = gpio_leds,
.num_leds = ARRAY_SIZE(gpio_leds),
};
static struct platform_device leds_gpio = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &gpio_led_info,
},
};
static struct gpio_keys_button gpio_buttons[] = {
{
.code = BTN_EXTRA,
/* Dynamically assigned depending on board */
.gpio = -EINVAL,
.desc = "user",
.wakeup = 1,
},
};
static struct gpio_keys_platform_data gpio_key_info = {
.buttons = gpio_buttons,
.nbuttons = ARRAY_SIZE(gpio_buttons),
};
static struct platform_device keys_gpio = {
.name = "gpio-keys",
.id = -1,
.dev = {
.platform_data = &gpio_key_info,
},
};
static struct platform_device madc_hwmon = {
.name = "twl4030_madc_hwmon",
.id = -1,
};
static struct platform_device *omap3_beagle_devices[] __initdata = {
&leds_gpio,
&keys_gpio,
&madc_hwmon,
&leds_pwm,
};
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
};
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif
static int __init beagle_opp_init(void)
{
int r = 0;
if (!machine_is_omap3_beagle())
return 0;
/* Initialize the omap3 opp table if not already created. */
r = omap3_opp_init();
if (r < 0 && (r != -EEXIST)) {
pr_err("%s: opp default init failed\n", __func__);
return r;
}
/* Custom OPP enabled for all xM versions */
if (cpu_is_omap3630()) {
struct device *mpu_dev, *iva_dev;
mpu_dev = get_cpu_device(0);
iva_dev = omap_device_get_by_hwmod_name("iva");
if (!mpu_dev || IS_ERR(iva_dev)) {
pr_err("%s: Aiee.. no mpu/dsp devices? %p %p\n",
__func__, mpu_dev, iva_dev);
return -ENODEV;
}
/* Enable MPU 1GHz and lower opps */
r = dev_pm_opp_enable(mpu_dev, 800000000);
/* TODO: MPU 1GHz needs SR and ABB */
/* Enable IVA 800MHz and lower opps */
r |= dev_pm_opp_enable(iva_dev, 660000000);
/* TODO: DSP 800MHz needs SR and ABB */
if (r) {
pr_err("%s: failed to enable higher opp %d\n",
__func__, r);
/*
* Cleanup - disable the higher freqs - we dont care
* about the results
*/
dev_pm_opp_disable(mpu_dev, 800000000);
dev_pm_opp_disable(iva_dev, 660000000);
}
}
return 0;
}
omap_device_initcall(beagle_opp_init);
static void __init omap3_beagle_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap3_beagle_init_rev();
if (gpio_is_valid(beagle_config.mmc1_gpio_wp))
omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
mmc[0].caps = beagle_config.mmc_caps;
omap_hsmmc_init(mmc);
omap3_beagle_i2c_init();
gpio_buttons[0].gpio = beagle_config.usr_button_gpio;
platform_add_devices(omap3_beagle_devices,
ARRAY_SIZE(omap3_beagle_devices));
if (gpio_is_valid(beagle_config.dvi_pd_gpio))
omap_mux_init_gpio(beagle_config.dvi_pd_gpio, OMAP_PIN_OUTPUT);
omap_display_init(&beagle_dss_data);
omap_serial_init();
omap_sdrc_init(mt46h32m32lf6_sdrc_params,
mt46h32m32lf6_sdrc_params);
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
board_nand_init(omap3beagle_nand_partitions,
ARRAY_SIZE(omap3beagle_nand_partitions), NAND_CS,
NAND_BUSWIDTH_16, NULL);
omap_twl4030_audio_init("omap3beagle", NULL);
/* Ensure msecure is mux'd to be able to set the RTC. */
omap_mux_init_signal("sys_drm_msecure", OMAP_PIN_OFF_OUTPUT_HIGH);
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
}
MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
/* Maintainer: Syed Mohammed Khasim - http://beagleboard.org */
.atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap3_init_early,
.init_irq = omap3_init_irq,
.init_machine = omap3_beagle_init,
.init_late = omap3_init_late,
.init_time = omap3_secure_sync32k_timer_init,
.restart = omap3xxx_restart,
MACHINE_END
/*
* board-overo.c (Gumstix Overo)
*
* Initial code: Steve Sakoman <steve@sakoman.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
* 02110-1301 USA
*
*/
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/i2c/twl.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/fixed.h>
#include <linux/spi/spi.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/mmc/host.h>
#include <linux/usb/phy.h>
#include <linux/platform_data/mtd-nand-omap2.h>
#include <linux/platform_data/spi-omap2-mcspi.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
#include <video/omapdss.h>
#include <video/omap-panel-data.h>
#include "common.h"
#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
#include "gpmc.h"
#include "hsmmc.h"
#include "board-flash.h"
#include "common-board-devices.h"
#define NAND_CS 0
#define OVERO_GPIO_BT_XGATE 15
#define OVERO_GPIO_W2W_NRESET 16
#define OVERO_GPIO_PENDOWN 114
#define OVERO_GPIO_BT_NRESET 164
#define OVERO_GPIO_USBH_CPEN 168
#define OVERO_GPIO_USBH_NRESET 183
#define OVERO_SMSC911X_CS 5
#define OVERO_SMSC911X_GPIO 176
#define OVERO_SMSC911X_NRESET 64
#define OVERO_SMSC911X2_CS 4
#define OVERO_SMSC911X2_GPIO 65
/* whether to register LCD35 instead of LCD43 */
static bool overo_use_lcd35;
#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
/* fixed regulator for ads7846 */
static struct regulator_consumer_supply ads7846_supply[] = {
REGULATOR_SUPPLY("vcc", "spi1.0"),
};
static struct regulator_init_data vads7846_regulator = {
.constraints = {
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(ads7846_supply),
.consumer_supplies = ads7846_supply,
};
static struct fixed_voltage_config vads7846 = {
.supply_name = "vads7846",
.microvolts = 3300000, /* 3.3V */
.gpio = -EINVAL,
.startup_delay = 0,
.init_data = &vads7846_regulator,
};
static struct platform_device vads7846_device = {
.name = "reg-fixed-voltage",
.id = 1,
.dev = {
.platform_data = &vads7846,
},
};
static void __init overo_ads7846_init(void)
{
omap_ads7846_init(1, OVERO_GPIO_PENDOWN, 0, NULL);
platform_device_register(&vads7846_device);
}
#else
static inline void __init overo_ads7846_init(void) { return; }
#endif
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
#include <linux/smsc911x.h>
#include "gpmc-smsc911x.h"
static struct omap_smsc911x_platform_data smsc911x_cfg = {
.id = 0,
.cs = OVERO_SMSC911X_CS,
.gpio_irq = OVERO_SMSC911X_GPIO,
.gpio_reset = OVERO_SMSC911X_NRESET,
.flags = SMSC911X_USE_32BIT,
};
static struct omap_smsc911x_platform_data smsc911x2_cfg = {
.id = 1,
.cs = OVERO_SMSC911X2_CS,
.gpio_irq = OVERO_SMSC911X2_GPIO,
.gpio_reset = -EINVAL,
.flags = SMSC911X_USE_32BIT,
};
static void __init overo_init_smsc911x(void)
{
gpmc_smsc911x_init(&smsc911x_cfg);
gpmc_smsc911x_init(&smsc911x2_cfg);
}
#else
static inline void __init overo_init_smsc911x(void) { return; }
#endif
/* DSS */
#define OVERO_GPIO_LCD_EN 144
#define OVERO_GPIO_LCD_BL 145
static struct connector_atv_platform_data overo_tv_pdata = {
.name = "tv",
.source = "venc.0",
.connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
.invert_polarity = false,
};
static struct platform_device overo_tv_connector_device = {
.name = "connector-analog-tv",
.id = 0,
.dev.platform_data = &overo_tv_pdata,
};
static const struct display_timing overo_lcd43_videomode = {
.pixelclock = { 0, 9200000, 0 },
.hactive = { 0, 480, 0 },
.hfront_porch = { 0, 8, 0 },
.hback_porch = { 0, 4, 0 },
.hsync_len = { 0, 41, 0 },
.vactive = { 0, 272, 0 },
.vfront_porch = { 0, 4, 0 },
.vback_porch = { 0, 2, 0 },
.vsync_len = { 0, 10, 0 },
.flags = DISPLAY_FLAGS_HSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW |
DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_POSEDGE,
};
static struct panel_dpi_platform_data overo_lcd43_pdata = {
.name = "lcd43",
.source = "dpi.0",
.data_lines = 24,
.display_timing = &overo_lcd43_videomode,
.enable_gpio = OVERO_GPIO_LCD_EN,
.backlight_gpio = OVERO_GPIO_LCD_BL,
};
static struct platform_device overo_lcd43_device = {
.name = "panel-dpi",
.id = 0,
.dev.platform_data = &overo_lcd43_pdata,
};
static struct connector_dvi_platform_data overo_dvi_connector_pdata = {
.name = "dvi",
.source = "tfp410.0",
.i2c_bus_num = 3,
};
static struct platform_device overo_dvi_connector_device = {
.name = "connector-dvi",
.id = 0,
.dev.platform_data = &overo_dvi_connector_pdata,
};
static struct encoder_tfp410_platform_data overo_tfp410_pdata = {
.name = "tfp410.0",
.source = "dpi.0",
.data_lines = 24,
.power_down_gpio = -1,
};
static struct platform_device overo_tfp410_device = {
.name = "tfp410",
.id = 0,
.dev.platform_data = &overo_tfp410_pdata,
};
static struct omap_dss_board_info overo_dss_data = {
.default_display_name = "lcd43",
};
static void __init overo_display_init(void)
{
omap_display_init(&overo_dss_data);
if (!overo_use_lcd35)
platform_device_register(&overo_lcd43_device);
platform_device_register(&overo_tfp410_device);
platform_device_register(&overo_dvi_connector_device);
platform_device_register(&overo_tv_connector_device);
}
static struct mtd_partition overo_nand_partitions[] = {
{
.name = "xloader",
.offset = 0, /* Offset = 0x00000 */
.size = 4 * NAND_BLOCK_SIZE,
.mask_flags = MTD_WRITEABLE
},
{
.name = "uboot",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
.size = 14 * NAND_BLOCK_SIZE,
},
{
.name = "uboot environment",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x240000 */
.size = 2 * NAND_BLOCK_SIZE,
},
{
.name = "linux",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
.size = 32 * NAND_BLOCK_SIZE,
},
{
.name = "rootfs",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
.size = MTDPART_SIZ_FULL,
},
};
static struct omap2_hsmmc_info mmc[] = {
{
.mmc = 1,
.caps = MMC_CAP_4_BIT_DATA,
.gpio_cd = -EINVAL,
.gpio_wp = -EINVAL,
},
{
.mmc = 2,
.caps = MMC_CAP_4_BIT_DATA,
.gpio_cd = -EINVAL,
.gpio_wp = -EINVAL,
.transceiver = true,
.ocr_mask = 0x00100000, /* 3.3V */
},
{} /* Terminator */
};
static struct regulator_consumer_supply overo_vmmc1_supply[] = {
REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
};
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
#include <linux/leds.h>
static struct gpio_led gpio_leds[] = {
{
.name = "overo:red:gpio21",
.default_trigger = "heartbeat",
.gpio = 21,
.active_low = true,
},
{
.name = "overo:blue:gpio22",
.default_trigger = "none",
.gpio = 22,
.active_low = true,
},
{
.name = "overo:blue:COM",
.default_trigger = "mmc0",
.gpio = -EINVAL, /* gets replaced */
.active_low = true,
},
};
static struct gpio_led_platform_data gpio_leds_pdata = {
.leds = gpio_leds,
.num_leds = ARRAY_SIZE(gpio_leds),
};
static struct platform_device gpio_leds_device = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &gpio_leds_pdata,
},
};
static void __init overo_init_led(void)
{
platform_device_register(&gpio_leds_device);
}
#else
static inline void __init overo_init_led(void) { return; }
#endif
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
#include <linux/input.h>
#include <linux/gpio_keys.h>
static struct gpio_keys_button gpio_buttons[] = {
{
.code = BTN_0,
.gpio = 23,
.desc = "button0",
.wakeup = 1,
},
{
.code = BTN_1,
.gpio = 14,
.desc = "button1",
.wakeup = 1,
},
};
static struct gpio_keys_platform_data gpio_keys_pdata = {
.buttons = gpio_buttons,
.nbuttons = ARRAY_SIZE(gpio_buttons),
};
static struct platform_device gpio_keys_device = {
.name = "gpio-keys",
.id = -1,
.dev = {
.platform_data = &gpio_keys_pdata,
},
};
static void __init overo_init_keys(void)
{
platform_device_register(&gpio_keys_device);
}
#else
static inline void __init overo_init_keys(void) { return; }
#endif
static int overo_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
#endif
return 0;
}
static struct twl4030_gpio_platform_data overo_gpio_data = {
.use_leds = true,
.setup = overo_twl_gpio_setup,
};
static struct regulator_init_data overo_vmmc1 = {
.constraints = {
.min_uV = 1850000,
.max_uV = 3150000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(overo_vmmc1_supply),
.consumer_supplies = overo_vmmc1_supply,
};
static struct twl4030_platform_data overo_twldata = {
.gpio = &overo_gpio_data,
.vmmc1 = &overo_vmmc1,
};
static int __init overo_i2c_init(void)
{
omap3_pmic_get_config(&overo_twldata,
TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO,
TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
overo_twldata.vpll2->constraints.name = "VDVI";
omap3_pmic_init("tps65950", &overo_twldata);
/* i2c2 pins are used for gpio */
omap_register_i2c_bus(3, 400, NULL, 0);
return 0;
}
static struct panel_lb035q02_platform_data overo_lcd35_pdata = {
.name = "lcd35",
.source = "dpi.0",
.data_lines = 24,
.enable_gpio = OVERO_GPIO_LCD_EN,
.backlight_gpio = OVERO_GPIO_LCD_BL,
};
/*
* NOTE: We need to add either the lgphilips panel, or the lcd43 panel. The
* selection is done based on the overo_use_lcd35 field. If new SPI
* devices are added here, extra work is needed to make only the lgphilips panel
* affected by the overo_use_lcd35 field.
*/
static struct spi_board_info overo_spi_board_info[] __initdata = {
{
.modalias = "panel_lgphilips_lb035q02",
.bus_num = 1,
.chip_select = 1,
.max_speed_hz = 500000,
.mode = SPI_MODE_3,
.platform_data = &overo_lcd35_pdata,
},
};
static int __init overo_spi_init(void)
{
overo_ads7846_init();
if (overo_use_lcd35) {
spi_register_board_info(overo_spi_board_info,
ARRAY_SIZE(overo_spi_board_info));
}
return 0;
}
static struct usbhs_phy_data phy_data[] __initdata = {
{
.port = 2,
.reset_gpio = OVERO_GPIO_USBH_NRESET,
.vcc_gpio = -EINVAL,
},
};
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
};
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif
static struct gpio overo_bt_gpios[] __initdata = {
{ OVERO_GPIO_BT_XGATE, GPIOF_OUT_INIT_LOW, "lcd enable" },
{ OVERO_GPIO_BT_NRESET, GPIOF_OUT_INIT_HIGH, "lcd bl enable" },
};
static struct regulator_consumer_supply dummy_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
REGULATOR_SUPPLY("vddvario", "smsc911x.1"),
REGULATOR_SUPPLY("vdd33a", "smsc911x.1"),
};
static void __init overo_init(void)
{
int ret;
if (strstr(boot_command_line, "omapdss.def_disp=lcd35"))
overo_use_lcd35 = true;
regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
overo_i2c_init();
omap_hsmmc_init(mmc);
omap_serial_init();
omap_sdrc_init(mt46h32m32lf6_sdrc_params,
mt46h32m32lf6_sdrc_params);
board_nand_init(overo_nand_partitions,
ARRAY_SIZE(overo_nand_partitions), NAND_CS, 0, NULL);
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(NULL);
usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
overo_spi_init();
overo_init_smsc911x();
overo_init_led();
overo_init_keys();
omap_twl4030_audio_init("overo", NULL);
overo_display_init();
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
ret = gpio_request_one(OVERO_GPIO_W2W_NRESET, GPIOF_OUT_INIT_HIGH,
"OVERO_GPIO_W2W_NRESET");
if (ret == 0) {
gpio_export(OVERO_GPIO_W2W_NRESET, 0);
gpio_set_value(OVERO_GPIO_W2W_NRESET, 0);
udelay(10);
gpio_set_value(OVERO_GPIO_W2W_NRESET, 1);
} else {
pr_err("could not obtain gpio for OVERO_GPIO_W2W_NRESET\n");
}
ret = gpio_request_array(overo_bt_gpios, ARRAY_SIZE(overo_bt_gpios));
if (ret) {
pr_err("%s: could not obtain BT gpios\n", __func__);
} else {
gpio_export(OVERO_GPIO_BT_XGATE, 0);
gpio_export(OVERO_GPIO_BT_NRESET, 0);
gpio_set_value(OVERO_GPIO_BT_NRESET, 0);
mdelay(6);
gpio_set_value(OVERO_GPIO_BT_NRESET, 1);
}
ret = gpio_request_one(OVERO_GPIO_USBH_CPEN, GPIOF_OUT_INIT_HIGH,
"OVERO_GPIO_USBH_CPEN");
if (ret == 0)
gpio_export(OVERO_GPIO_USBH_CPEN, 0);
else
pr_err("could not obtain gpio for OVERO_GPIO_USBH_CPEN\n");
}
MACHINE_START(OVERO, "Gumstix Overo")
.atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap35xx_init_early,
.init_irq = omap3_init_irq,
.init_machine = overo_init,
.init_late = omap35xx_init_late,
.init_time = omap3_sync32k_timer_init,
.restart = omap3xxx_restart,
MACHINE_END
......@@ -63,7 +63,7 @@ static int __init omap3_l3_init(void)
WARN(IS_ERR(pdev), "could not build omap_device for %s\n", oh_name);
return PTR_RET(pdev);
return PTR_ERR_OR_ZERO(pdev);
}
omap_postcore_initcall(omap3_l3_init);
......@@ -333,6 +333,6 @@ static int __init omap_gpmc_init(void)
pdev = omap_device_build("omap-gpmc", -1, oh, NULL, 0);
WARN(IS_ERR(pdev), "could not build omap_device for %s\n", oh_name);
return PTR_RET(pdev);
return PTR_ERR_OR_ZERO(pdev);
}
omap_postcore_initcall(omap_gpmc_init);
......@@ -84,7 +84,7 @@ int __init omap_init_vrfb(void)
pdev = platform_device_register_resndata(NULL, "omapvrfb", -1,
res, num_res, NULL, 0);
return PTR_RET(pdev);
return PTR_ERR_OR_ZERO(pdev);
}
#else
int __init omap_init_vrfb(void) { return 0; }
......
......@@ -216,11 +216,11 @@ static void omap2_onenand_calc_sync_timings(struct gpmc_timings *t,
div = gpmc_calc_divider(min_gpmc_clk_period);
gpmc_clk_ns = gpmc_ticks_to_ns(div);
if (gpmc_clk_ns < 15) /* >66Mhz */
if (gpmc_clk_ns < 15) /* >66MHz */
onenand_flags |= ONENAND_FLAG_HF;
else
onenand_flags &= ~ONENAND_FLAG_HF;
if (gpmc_clk_ns < 12) /* >83Mhz */
if (gpmc_clk_ns < 12) /* >83MHz */
onenand_flags |= ONENAND_FLAG_VHF;
else
onenand_flags &= ~ONENAND_FLAG_VHF;
......
......@@ -70,7 +70,7 @@ static void omap_hsmmc1_before_set_reg(struct device *dev,
reg = omap_ctrl_readl(control_pbias_offset);
if (cpu_is_omap3630()) {
/* Set MMC I/O to 52Mhz */
/* Set MMC I/O to 52MHz */
prog_io = omap_ctrl_readl(OMAP343X_CONTROL_PROG_IO1);
prog_io |= OMAP3630_PRG_SDMMC1_SPEEDCTRL;
omap_ctrl_writel(prog_io, OMAP343X_CONTROL_PROG_IO1);
......
......@@ -444,7 +444,7 @@ static int wakeupgen_domain_alloc(struct irq_domain *domain,
return irq_domain_alloc_irqs_parent(domain, virq, nr_irqs, &parent_args);
}
static struct irq_domain_ops wakeupgen_domain_ops = {
static const struct irq_domain_ops wakeupgen_domain_ops = {
.xlate = wakeupgen_domain_xlate,
.alloc = wakeupgen_domain_alloc,
.free = irq_domain_free_irqs_common,
......
......@@ -116,7 +116,7 @@ const struct prcm_config omap2430_rate_table[] = {
RATE_IN_243X},
/* PRCM-boot/bypass */
{S13M, S13M, S13M, RB_CM_CLKSEL_MPU_VAL, /* 13Mhz */
{S13M, S13M, S13M, RB_CM_CLKSEL_MPU_VAL, /* 13MHz */
RB_CM_CLKSEL_DSP_VAL, RB_CM_CLKSEL_GFX_VAL,
RB_CM_CLKSEL1_CORE_VAL, MB_CM_CLKSEL1_PLL_13_VAL,
MX_CLKSEL2_PLL_2x_VAL, RB_CM_CLKSEL_MDM_VAL,
......@@ -124,7 +124,7 @@ const struct prcm_config omap2430_rate_table[] = {
RATE_IN_243X},
/* PRCM-boot/bypass */
{S12M, S12M, S12M, RB_CM_CLKSEL_MPU_VAL, /* 12Mhz */
{S12M, S12M, S12M, RB_CM_CLKSEL_MPU_VAL, /* 12MHz */
RB_CM_CLKSEL_DSP_VAL, RB_CM_CLKSEL_GFX_VAL,
RB_CM_CLKSEL1_CORE_VAL, MB_CM_CLKSEL1_PLL_12_VAL,
MX_CLKSEL2_PLL_2x_VAL, RB_CM_CLKSEL_MDM_VAL,
......
......@@ -55,7 +55,7 @@ static int __init omap2_init_pmu(unsigned oh_num, char *oh_names[])
WARN(IS_ERR(omap_pmu_dev), "Can't build omap_device for %s.\n",
dev_name);
return PTR_RET(omap_pmu_dev);
return PTR_ERR_OR_ZERO(omap_pmu_dev);
}
static int __init omap_init_pmu(void)
......
......@@ -164,6 +164,6 @@ void omap2xxx_sdrc_init_params(u32 force_lock_to_unlock_mode)
mem_timings.slow_dll_ctrl |=
((mem_timings.fast_dll_ctrl & 0xF) | (1 << 2));
/* 90 degree phase for anything below 133Mhz + disable DLL filter */
/* 90 degree phase for anything below 133MHz + disable DLL filter */
mem_timings.slow_dll_ctrl |= ((1 << 1) | (3 << 8));
}
......@@ -203,7 +203,7 @@ static int __init omap_serial_early_init(void)
if (cmdline_find_option(uart_name)) {
console_uart_id = uart->num;
if (console_loglevel >= 10) {
if (console_loglevel >= CONSOLE_LOGLEVEL_DEBUG) {
uart_debug = true;
pr_info("%s used as console in debug mode: uart%d clocks will not be gated",
uart_name, uart->num);
......
......@@ -64,7 +64,7 @@ ENTRY(omap242x_sram_ddr_init)
mvn r9, #0x4 @ mask to get clear bit2
and r10, r10, r9 @ clear bit2 for lock mode.
orr r10, r10, #0x8 @ make sure DLL on (es2 bit pos)
orr r10, r10, #0x2 @ 90 degree phase for all below 133Mhz
orr r10, r10, #0x2 @ 90 degree phase for all below 133MHz
str r10, [r11] @ commit to DLLA_CTRL
bl i_dll_wait @ wait for dll to lock
......
......@@ -64,7 +64,7 @@ ENTRY(omap243x_sram_ddr_init)
mvn r9, #0x4 @ mask to get clear bit2
and r10, r10, r9 @ clear bit2 for lock mode.
orr r10, r10, #0x8 @ make sure DLL on (es2 bit pos)
orr r10, r10, #0x2 @ 90 degree phase for all below 133Mhz
orr r10, r10, #0x2 @ 90 degree phase for all below 133MHz
str r10, [r11] @ commit to DLLA_CTRL
bl i_dll_wait @ wait for dll to lock
......
......@@ -15,7 +15,6 @@
* ready for them to initialise.
*/
ENTRY(sirfsoc_secondary_startup)
bl v7_invalidate_l1
mrc p15, 0, r0, c0, c0, 5
and r0, r0, #15
adr r4, 1f
......
......@@ -28,7 +28,7 @@
static void isp116x_pfm_delay(struct device *dev, int delay)
{
/* 400Mhz PXA2 = 2.5ns / instruction */
/* 400MHz PXA2 = 2.5ns / instruction */
int cyc = delay / 10;
......
......@@ -17,4 +17,3 @@ extern char rockchip_secondary_trampoline;
extern char rockchip_secondary_trampoline_end;
extern unsigned long rockchip_boot_fn;
extern void rockchip_secondary_startup(void);
......@@ -15,14 +15,6 @@
#include <linux/linkage.h>
#include <linux/init.h>
ENTRY(rockchip_secondary_startup)
mrc p15, 0, r0, c0, c0, 0 @ read main ID register
ldr r1, =0x00000c09 @ Cortex-A9 primary part number
teq r0, r1
beq v7_invalidate_l1
b secondary_startup
ENDPROC(rockchip_secondary_startup)
ENTRY(rockchip_secondary_trampoline)
ldr pc, 1f
ENDPROC(rockchip_secondary_trampoline)
......
......@@ -149,8 +149,7 @@ static int __cpuinit rockchip_boot_secondary(unsigned int cpu,
* sram_base_addr + 8: start address for pc
* */
udelay(10);
writel(virt_to_phys(rockchip_secondary_startup),
sram_base_addr + 8);
writel(virt_to_phys(secondary_startup), sram_base_addr + 8);
writel(0xDEADBEAF, sram_base_addr + 4);
dsb_sev();
}
......@@ -189,7 +188,7 @@ static int __init rockchip_smp_prepare_sram(struct device_node *node)
}
/* set the boot function for the sram code */
rockchip_boot_fn = virt_to_phys(rockchip_secondary_startup);
rockchip_boot_fn = virt_to_phys(secondary_startup);
/* copy the trampoline to sram, that runs during startup of the core */
memcpy(sram_base_addr, &rockchip_secondary_trampoline, trampoline_sz);
......
......@@ -14,7 +14,6 @@ extern void shmobile_smp_sleep(void);
extern void shmobile_smp_hook(unsigned int cpu, unsigned long fn,
unsigned long arg);
extern int shmobile_smp_cpu_disable(unsigned int cpu);
extern void shmobile_invalidate_start(void);
extern void shmobile_boot_scu(void);
extern void shmobile_smp_scu_prepare_cpus(unsigned int max_cpus);
extern void shmobile_smp_scu_cpu_die(unsigned int cpu);
......
......@@ -22,7 +22,7 @@
* Boot code for secondary CPUs.
*
* First we turn on L1 cache coherency for our CPU. Then we jump to
* shmobile_invalidate_start that invalidates the cache and hands over control
* secondary_startup that invalidates the cache and hands over control
* to the common ARM startup code.
*/
ENTRY(shmobile_boot_scu)
......@@ -36,7 +36,7 @@ ENTRY(shmobile_boot_scu)
bic r2, r2, r3 @ Clear bits of our CPU (Run Mode)
str r2, [r0, #8] @ write back
b shmobile_invalidate_start
b secondary_startup
ENDPROC(shmobile_boot_scu)
.text
......
......@@ -16,13 +16,6 @@
#include <asm/assembler.h>
#include <asm/memory.h>
#ifdef CONFIG_SMP
ENTRY(shmobile_invalidate_start)
bl v7_invalidate_l1
b secondary_startup
ENDPROC(shmobile_invalidate_start)
#endif
/*
* Reset vector for secondary CPUs.
* This will be mapped at address 0 by SBAR register.
......
......@@ -133,7 +133,7 @@ void __init shmobile_smp_apmu_prepare_cpus(unsigned int max_cpus,
int shmobile_smp_apmu_boot_secondary(unsigned int cpu, struct task_struct *idle)
{
/* For this particular CPU register boot vector */
shmobile_smp_hook(cpu, virt_to_phys(shmobile_invalidate_start), 0);
shmobile_smp_hook(cpu, virt_to_phys(secondary_startup), 0);
return apmu_wrap(cpu, apmu_power_on);
}
......
......@@ -31,7 +31,6 @@
#define RSTMGR_MPUMODRST_CPU1 0x2 /* CPU1 Reset */
extern void socfpga_secondary_startup(void);
extern void __iomem *socfpga_scu_base_addr;
extern void socfpga_init_clocks(void);
......
......@@ -30,8 +30,3 @@ ENTRY(secondary_trampoline)
1: .long .
.long socfpga_cpu1start_addr
ENTRY(secondary_trampoline_end)
ENTRY(socfpga_secondary_startup)
bl v7_invalidate_l1
b secondary_startup
ENDPROC(socfpga_secondary_startup)
......@@ -40,7 +40,7 @@ static int socfpga_boot_secondary(unsigned int cpu, struct task_struct *idle)
memcpy(phys_to_virt(0), &secondary_trampoline, trampoline_size);
writel(virt_to_phys(socfpga_secondary_startup),
writel(virt_to_phys(secondary_startup),
sys_manager_base_addr + (socfpga_cpu1start_addr & 0x000000ff));
flush_cache_all();
......
......@@ -19,7 +19,7 @@ obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += pm-tegra30.o
ifeq ($(CONFIG_CPU_IDLE),y)
obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += cpuidle-tegra30.o
endif
obj-$(CONFIG_SMP) += platsmp.o headsmp.o
obj-$(CONFIG_SMP) += platsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
obj-$(CONFIG_ARCH_TEGRA_114_SOC) += sleep-tegra30.o
......
#include <linux/linkage.h>
#include <linux/init.h>
#include "sleep.h"
.section ".text.head", "ax"
ENTRY(tegra_secondary_startup)
check_cpu_part_num 0xc09, r8, r9
bleq v7_invalidate_l1
b secondary_startup
ENDPROC(tegra_secondary_startup)
......@@ -94,7 +94,7 @@ void __init tegra_cpu_reset_handler_init(void)
__tegra_cpu_reset_handler_data[TEGRA_RESET_MASK_PRESENT] =
*((u32 *)cpu_possible_mask);
__tegra_cpu_reset_handler_data[TEGRA_RESET_STARTUP_SECONDARY] =
virt_to_phys((void *)tegra_secondary_startup);
virt_to_phys((void *)secondary_startup);
#endif
#ifdef CONFIG_PM_SLEEP
......
......@@ -36,7 +36,6 @@ extern unsigned long __tegra_cpu_reset_handler_data[TEGRA_RESET_DATA_SIZE];
void __tegra_cpu_reset_handler_start(void);
void __tegra_cpu_reset_handler(void);
void __tegra_cpu_reset_handler_end(void);
void tegra_secondary_startup(void);
#ifdef CONFIG_PM_SLEEP
#define tegra_cpu_lp1_mask \
......
......@@ -223,7 +223,7 @@ wfe_war:
b __cpu_reset_again
/*
* 38 nop's, which fills reset of wfe cache line and
* 38 nop's, which fills rest of wfe cache line and
* 4 more cachelines with nop
*/
.rept 38
......
......@@ -6,6 +6,7 @@
#include <linux/io.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <asm/hardware/cache-l2x0.h>
......@@ -15,7 +16,14 @@
static int __init ux500_l2x0_unlock(void)
{
int i;
void __iomem *l2x0_base = __io_address(U8500_L2CC_BASE);
struct device_node *np;
void __iomem *l2x0_base;
np = of_find_compatible_node(NULL, NULL, "arm,pl310-cache");
l2x0_base = of_iomap(np, 0);
of_node_put(np);
if (!l2x0_base)
return -ENODEV;
/*
* Unlock Data and Instruction Lock if locked. Ux500 U-Boot versions
......@@ -30,6 +38,7 @@ static int __init ux500_l2x0_unlock(void)
writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_I_BASE +
i * L2X0_LOCKDOWN_STRIDE);
}
iounmap(l2x0_base);
return 0;
}
......
......@@ -43,60 +43,10 @@ static struct prcmu_pdata db8500_prcmu_pdata = {
.legacy_offset = DB8500_PRCMU_LEGACY_OFFSET,
};
/* minimum static i/o mapping required to boot U8500 platforms */
static struct map_desc u8500_uart_io_desc[] __initdata = {
__IO_DEV_DESC(U8500_UART0_BASE, SZ_4K),
__IO_DEV_DESC(U8500_UART2_BASE, SZ_4K),
};
/* U8500 and U9540 common io_desc */
static struct map_desc u8500_common_io_desc[] __initdata = {
/* SCU base also covers GIC CPU BASE and TWD with its 4K page */
__IO_DEV_DESC(U8500_SCU_BASE, SZ_4K),
__IO_DEV_DESC(U8500_GIC_DIST_BASE, SZ_4K),
__IO_DEV_DESC(U8500_L2CC_BASE, SZ_4K),
__IO_DEV_DESC(U8500_MTU0_BASE, SZ_4K),
__IO_DEV_DESC(U8500_BACKUPRAM0_BASE, SZ_8K),
__IO_DEV_DESC(U8500_CLKRST1_BASE, SZ_4K),
__IO_DEV_DESC(U8500_CLKRST2_BASE, SZ_4K),
__IO_DEV_DESC(U8500_CLKRST3_BASE, SZ_4K),
__IO_DEV_DESC(U8500_CLKRST5_BASE, SZ_4K),
__IO_DEV_DESC(U8500_CLKRST6_BASE, SZ_4K),
__IO_DEV_DESC(U8500_GPIO0_BASE, SZ_4K),
__IO_DEV_DESC(U8500_GPIO1_BASE, SZ_4K),
__IO_DEV_DESC(U8500_GPIO2_BASE, SZ_4K),
__IO_DEV_DESC(U8500_GPIO3_BASE, SZ_4K),
};
/* U8500 IO map specific description */
static struct map_desc u8500_io_desc[] __initdata = {
__IO_DEV_DESC(U8500_PRCMU_BASE, SZ_4K),
__IO_DEV_DESC(U8500_PRCMU_TCDM_BASE, SZ_4K),
};
/* U9540 IO map specific description */
static struct map_desc u9540_io_desc[] __initdata = {
__IO_DEV_DESC(U8500_PRCMU_BASE, SZ_4K + SZ_8K),
__IO_DEV_DESC(U8500_PRCMU_TCDM_BASE, SZ_4K + SZ_8K),
};
static void __init u8500_map_io(void)
{
/*
* Map the UARTs early so that the DEBUG_LL stuff continues to work.
*/
iotable_init(u8500_uart_io_desc, ARRAY_SIZE(u8500_uart_io_desc));
ux500_map_io();
iotable_init(u8500_common_io_desc, ARRAY_SIZE(u8500_common_io_desc));
if (cpu_is_ux540_family())
iotable_init(u9540_io_desc, ARRAY_SIZE(u9540_io_desc));
else
iotable_init(u8500_io_desc, ARRAY_SIZE(u8500_io_desc));
debug_ll_io_init();
ux500_setup_id();
}
/*
......@@ -125,14 +75,18 @@ static struct arm_pmu_platdata db8500_pmu_platdata = {
static const char *db8500_read_soc_id(void)
{
void __iomem *uid = __io_address(U8500_BB_UID_BASE);
void __iomem *uid;
uid = ioremap(U8500_BB_UID_BASE, 0x20);
if (!uid)
return NULL;
/* Throw these device-specific numbers into the entropy pool */
add_device_randomness(uid, 0x14);
return kasprintf(GFP_KERNEL, "%08x%08x%08x%08x%08x",
readl((u32 *)uid+0),
readl((u32 *)uid+1), readl((u32 *)uid+2),
readl((u32 *)uid+3), readl((u32 *)uid+4));
iounmap(uid);
}
static struct device * __init db8500_soc_device_init(void)
......
......@@ -16,6 +16,7 @@
#include <linux/stat.h>
#include <linux/of.h>
#include <linux/of_irq.h>
#include <linux/of_address.h>
#include <linux/irq.h>
#include <linux/irqchip.h>
#include <linux/irqchip/arm-gic.h>
......@@ -52,31 +53,36 @@ void ux500_restart(enum reboot_mode mode, const char *cmd)
*/
void __init ux500_init_irq(void)
{
struct device_node *np;
struct resource r;
gic_set_irqchip_flags(IRQCHIP_SKIP_SET_WAKE | IRQCHIP_MASK_ON_SUSPEND);
irqchip_init();
np = of_find_compatible_node(NULL, NULL, "stericsson,db8500-prcmu");
of_address_to_resource(np, 0, &r);
of_node_put(np);
if (!r.start) {
pr_err("could not find PRCMU base resource\n");
return;
}
prcmu_early_init(r.start, r.end-r.start);
ux500_pm_init(r.start, r.end-r.start);
/*
* Init clocks here so that they are available for system timer
* initialization.
*/
if (cpu_is_u8500_family()) {
prcmu_early_init(U8500_PRCMU_BASE, SZ_8K - 1);
ux500_pm_init(U8500_PRCMU_BASE, SZ_8K - 1);
u8500_of_clk_init(U8500_CLKRST1_BASE,
U8500_CLKRST2_BASE,
U8500_CLKRST3_BASE,
U8500_CLKRST5_BASE,
U8500_CLKRST6_BASE);
} else if (cpu_is_u9540()) {
prcmu_early_init(U8500_PRCMU_BASE, SZ_8K - 1);
ux500_pm_init(U8500_PRCMU_BASE, SZ_8K - 1);
u9540_clk_init(U8500_CLKRST1_BASE, U8500_CLKRST2_BASE,
U8500_CLKRST3_BASE, U8500_CLKRST5_BASE,
U8500_CLKRST6_BASE);
} else if (cpu_is_u8540()) {
prcmu_early_init(U8500_PRCMU_BASE, SZ_8K + SZ_4K - 1);
ux500_pm_init(U8500_PRCMU_BASE, SZ_8K + SZ_4K - 1);
u8540_clk_init(U8500_CLKRST1_BASE, U8500_CLKRST2_BASE,
U8500_CLKRST3_BASE, U8500_CLKRST5_BASE,
U8500_CLKRST6_BASE);
......
......@@ -72,7 +72,7 @@ static unsigned int partnumber(unsigned int asicid)
* DB9540 0x413fc090 0xFFFFDBF4 0x009540xx
*/
void __init ux500_map_io(void)
void __init ux500_setup_id(void)
{
unsigned int cpuid = read_cpuid_id();
unsigned int asicid = 0;
......
......@@ -16,6 +16,8 @@
#include <linux/device.h>
#include <linux/smp.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <asm/cacheflush.h>
#include <asm/smp_plat.h>
......@@ -26,6 +28,9 @@
#include "db8500-regs.h"
#include "id.h"
static void __iomem *scu_base;
static void __iomem *backupram;
/* This is called from headsmp.S to wakeup the secondary core */
extern void u8500_secondary_startup(void);
......@@ -41,16 +46,6 @@ static void write_pen_release(int val)
sync_cache_w(&pen_release);
}
static void __iomem *scu_base_addr(void)
{
if (cpu_is_u8500_family() || cpu_is_ux540_family())
return __io_address(U8500_SCU_BASE);
else
ux500_unknown_soc();
return NULL;
}
static DEFINE_SPINLOCK(boot_lock);
static void ux500_secondary_init(unsigned int cpu)
......@@ -104,13 +99,6 @@ static int ux500_boot_secondary(unsigned int cpu, struct task_struct *idle)
static void __init wakeup_secondary(void)
{
void __iomem *backupram;
if (cpu_is_u8500_family() || cpu_is_ux540_family())
backupram = __io_address(U8500_BACKUPRAM0_BASE);
else
ux500_unknown_soc();
/*
* write the address of secondary startup into the backup ram register
* at offset 0x1FF4, then write the magic number 0xA1FEED01 to the
......@@ -135,10 +123,16 @@ static void __init wakeup_secondary(void)
*/
static void __init ux500_smp_init_cpus(void)
{
void __iomem *scu_base = scu_base_addr();
unsigned int i, ncores;
struct device_node *np;
ncores = scu_base ? scu_get_core_count(scu_base) : 1;
np = of_find_compatible_node(NULL, NULL, "arm,cortex-a9-scu");
scu_base = of_iomap(np, 0);
of_node_put(np);
if (!scu_base)
return;
backupram = ioremap(U8500_BACKUPRAM0_BASE, SZ_8K);
ncores = scu_get_core_count(scu_base);
/* sanity check */
if (ncores > nr_cpu_ids) {
......@@ -153,8 +147,7 @@ static void __init ux500_smp_init_cpus(void)
static void __init ux500_smp_prepare_cpus(unsigned int max_cpus)
{
scu_enable(scu_base_addr());
scu_enable(scu_base);
wakeup_secondary();
}
......
......@@ -15,6 +15,8 @@
#include <linux/io.h>
#include <linux/suspend.h>
#include <linux/platform_data/arm-ux500-pm.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include "db8500-regs.h"
#include "pm_domains.h"
......@@ -42,6 +44,7 @@
#define PRCM_ARMITVAL127TO96 (prcmu_base + 0x26C)
static void __iomem *prcmu_base;
static void __iomem *dist_base;
/* This function decouple the gic from the prcmu */
int prcmu_gic_decouple(void)
......@@ -88,7 +91,6 @@ bool prcmu_gic_pending_irq(void)
{
u32 pr; /* Pending register */
u32 er; /* Enable register */
void __iomem *dist_base = __io_address(U8500_GIC_DIST_BASE);
int i;
/* 5 registers. STI & PPI not skipped */
......@@ -143,7 +145,6 @@ bool prcmu_is_cpu_in_wfi(int cpu)
int prcmu_copy_gic_settings(void)
{
u32 er; /* Enable register */
void __iomem *dist_base = __io_address(U8500_GIC_DIST_BASE);
int i;
/* We skip the STI and PPI */
......@@ -179,11 +180,21 @@ static const struct platform_suspend_ops ux500_suspend_ops = {
void __init ux500_pm_init(u32 phy_base, u32 size)
{
struct device_node *np;
prcmu_base = ioremap(phy_base, size);
if (!prcmu_base) {
pr_err("could not remap PRCMU for PM functions\n");
return;
}
np = of_find_compatible_node(NULL, NULL, "arm,cortex-a9-gic");
dist_base = of_iomap(np, 0);
of_node_put(np);
if (!dist_base) {
pr_err("could not remap GIC dist base for PM functions\n");
return;
}
/*
* On watchdog reboot the GIC is in some cases decoupled.
* This will make sure that the GIC is correctly configured.
......
......@@ -18,7 +18,7 @@
void ux500_restart(enum reboot_mode mode, const char *cmd);
void __init ux500_map_io(void);
void __init ux500_setup_id(void);
extern void __init ux500_init_irq(void);
......@@ -26,20 +26,6 @@ extern struct device *ux500_soc_device_init(const char *soc_id);
extern void ux500_timer_init(void);
#define __IO_DEV_DESC(x, sz) { \
.virtual = IO_ADDRESS(x), \
.pfn = __phys_to_pfn(x), \
.length = sz, \
.type = MT_DEVICE, \
}
#define __MEM_DEV_DESC(x, sz) { \
.virtual = IO_ADDRESS(x), \
.pfn = __phys_to_pfn(x), \
.length = sz, \
.type = MT_MEMORY_RWX, \
}
extern struct smp_operations ux500_smp_ops;
extern void ux500_cpu_die(unsigned int cpu);
......
......@@ -17,8 +17,6 @@
#ifndef __MACH_ZYNQ_COMMON_H__
#define __MACH_ZYNQ_COMMON_H__
void zynq_secondary_startup(void);
extern int zynq_slcr_init(void);
extern int zynq_early_slcr_init(void);
extern void zynq_slcr_system_reset(void);
......
......@@ -22,8 +22,3 @@ zynq_secondary_trampoline_jump:
.globl zynq_secondary_trampoline_end
zynq_secondary_trampoline_end:
ENDPROC(zynq_secondary_trampoline)
ENTRY(zynq_secondary_startup)
bl v7_invalidate_l1
b secondary_startup
ENDPROC(zynq_secondary_startup)
......@@ -87,10 +87,9 @@ int zynq_cpun_start(u32 address, int cpu)
}
EXPORT_SYMBOL(zynq_cpun_start);
static int zynq_boot_secondary(unsigned int cpu,
struct task_struct *idle)
static int zynq_boot_secondary(unsigned int cpu, struct task_struct *idle)
{
return zynq_cpun_start(virt_to_phys(zynq_secondary_startup), cpu);
return zynq_cpun_start(virt_to_phys(secondary_startup), cpu);
}
/*
......
......@@ -336,7 +336,7 @@ __v7_pj4b_setup:
__v7_setup:
adr r12, __v7_setup_stack @ the local stack
stmia r12, {r0-r5, r7, r9, r11, lr}
bl v7_flush_dcache_louis
bl v7_invalidate_l1
ldmia r12, {r0-r5, r7, r9, r11, lr}
mrc p15, 0, r0, c0, c0, 0 @ read main ID register
......
/*
* Skeleton device tree; the bare minimum needed to boot; just include and
* add a compatible value. The bootloader will typically populate the memory
* node.
*/
/ {
#address-cells = <2>;
#size-cells = <1>;
chosen { };
aliases { };
memory { device_type = "memory"; reg = <0 0 0>; };
};
......@@ -845,7 +845,6 @@ config PATA_AT32
config PATA_AT91
tristate "PATA support for AT91SAM9260"
depends on ARM && SOC_AT91SAM9
depends on !ARCH_MULTIPLATFORM
help
This option enables support for IDE devices on the Atmel AT91SAM9260 SoC.
......
......@@ -24,11 +24,13 @@
#include <linux/ata.h>
#include <linux/clk.h>
#include <linux/libata.h>
#include <linux/mfd/syscon.h>
#include <linux/mfd/syscon/atmel-smc.h>
#include <linux/platform_device.h>
#include <linux/ata_platform.h>
#include <linux/platform_data/atmel.h>
#include <linux/regmap.h>
#include <mach/at91sam9_smc.h>
#include <asm/gpio.h>
#define DRV_NAME "pata_at91"
......@@ -57,6 +59,15 @@ struct smc_range {
int max;
};
struct regmap *smc;
struct at91sam9_smc_generic_fields {
struct regmap_field *setup;
struct regmap_field *pulse;
struct regmap_field *cycle;
struct regmap_field *mode;
} fields;
/**
* adjust_smc_value - adjust value for one of SMC registers.
* @value: adjusted value
......@@ -206,7 +217,6 @@ static void set_smc_timing(struct device *dev, struct ata_device *adev,
{
int ret = 0;
int use_iordy;
struct sam9_smc_config smc;
unsigned int t6z; /* data tristate time in ns */
unsigned int cycle; /* SMC Cycle width in MCK ticks */
unsigned int setup; /* SMC Setup width in MCK ticks */
......@@ -244,19 +254,21 @@ static void set_smc_timing(struct device *dev, struct ata_device *adev,
dev_dbg(dev, "Use IORDY=%u, TDF Cycles=%u\n", use_iordy, tdf_cycles);
/* SMC Setup Register */
smc.nwe_setup = smc.nrd_setup = setup;
smc.ncs_write_setup = smc.ncs_read_setup = 0;
/* SMC Pulse Register */
smc.nwe_pulse = smc.nrd_pulse = pulse;
smc.ncs_write_pulse = smc.ncs_read_pulse = cs_pulse;
/* SMC Cycle Register */
smc.write_cycle = smc.read_cycle = cycle;
/* SMC Mode Register*/
smc.tdf_cycles = tdf_cycles;
smc.mode = info->mode;
sam9_smc_configure(0, info->cs, &smc);
regmap_fields_write(fields.setup, info->cs,
AT91SAM9_SMC_NRDSETUP(setup) |
AT91SAM9_SMC_NWESETUP(setup) |
AT91SAM9_SMC_NCS_NRDSETUP(0) |
AT91SAM9_SMC_NCS_WRSETUP(0));
regmap_fields_write(fields.pulse, info->cs,
AT91SAM9_SMC_NRDPULSE(pulse) |
AT91SAM9_SMC_NWEPULSE(pulse) |
AT91SAM9_SMC_NCS_NRDPULSE(cs_pulse) |
AT91SAM9_SMC_NCS_WRPULSE(cs_pulse));
regmap_fields_write(fields.cycle, info->cs,
AT91SAM9_SMC_NRDCYCLE(cycle) |
AT91SAM9_SMC_NWECYCLE(cycle));
regmap_fields_write(fields.mode, info->cs, info->mode |
AT91_SMC_TDF_(tdf_cycles));
}
static void pata_at91_set_piomode(struct ata_port *ap, struct ata_device *adev)
......@@ -280,21 +292,21 @@ static unsigned int pata_at91_data_xfer_noirq(struct ata_device *dev,
{
struct at91_ide_info *info = dev->link->ap->host->private_data;
unsigned int consumed;
unsigned int mode;
unsigned long flags;
struct sam9_smc_config smc;
local_irq_save(flags);
sam9_smc_read_mode(0, info->cs, &smc);
regmap_fields_read(fields.mode, info->cs, &mode);
/* set 16bit mode before writing data */
smc.mode = (smc.mode & ~AT91_SMC_DBW) | AT91_SMC_DBW_16;
sam9_smc_write_mode(0, info->cs, &smc);
regmap_fields_write(fields.mode, info->cs, (mode & ~AT91_SMC_DBW) |
AT91_SMC_DBW_16);
consumed = ata_sff_data_xfer(dev, buf, buflen, rw);
/* restore 8bit mode after data is written */
smc.mode = (smc.mode & ~AT91_SMC_DBW) | AT91_SMC_DBW_8;
sam9_smc_write_mode(0, info->cs, &smc);
regmap_fields_write(fields.mode, info->cs, (mode & ~AT91_SMC_DBW) |
AT91_SMC_DBW_8);
local_irq_restore(flags);
return consumed;
......@@ -312,6 +324,36 @@ static struct ata_port_operations pata_at91_port_ops = {
.cable_detect = ata_cable_40wire,
};
static int at91sam9_smc_fields_init(struct device *dev)
{
struct reg_field field = REG_FIELD(0, 0, 31);
field.id_size = 8;
field.id_offset = AT91SAM9_SMC_GENERIC_BLK_SZ;
field.reg = AT91SAM9_SMC_SETUP(AT91SAM9_SMC_GENERIC);
fields.setup = devm_regmap_field_alloc(dev, smc, field);
if (IS_ERR(fields.setup))
return PTR_ERR(fields.setup);
field.reg = AT91SAM9_SMC_PULSE(AT91SAM9_SMC_GENERIC);
fields.pulse = devm_regmap_field_alloc(dev, smc, field);
if (IS_ERR(fields.pulse))
return PTR_ERR(fields.pulse);
field.reg = AT91SAM9_SMC_CYCLE(AT91SAM9_SMC_GENERIC);
fields.cycle = devm_regmap_field_alloc(dev, smc, field);
if (IS_ERR(fields.cycle))
return PTR_ERR(fields.cycle);
field.reg = AT91SAM9_SMC_MODE(AT91SAM9_SMC_GENERIC);
fields.mode = devm_regmap_field_alloc(dev, smc, field);
if (IS_ERR(fields.mode))
return PTR_ERR(fields.mode);
return 0;
}
static int pata_at91_probe(struct platform_device *pdev)
{
struct at91_cf_data *board = dev_get_platdata(&pdev->dev);
......@@ -341,6 +383,14 @@ static int pata_at91_probe(struct platform_device *pdev)
irq = board->irq_pin;
smc = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, "atmel,smc");
if (IS_ERR(smc))
return PTR_ERR(smc);
ret = at91sam9_smc_fields_init(dev);
if (ret < 0)
return ret;
/* init ata host */
host = ata_host_alloc(dev, 1);
......
......@@ -277,7 +277,6 @@ config AT91_CF
tristate "AT91 CompactFlash Controller"
depends on PCI
depends on PCMCIA && ARCH_AT91
depends on !ARCH_MULTIPLATFORM
help
Say Y here to support the CompactFlash controller on AT91 chips.
Or choose M to compile the driver as a module named "at91_cf".
......
......@@ -20,16 +20,15 @@
#include <linux/platform_data/atmel.h>
#include <linux/io.h>
#include <linux/sizes.h>
#include <linux/mfd/syscon.h>
#include <linux/mfd/syscon/atmel-mc.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/of_gpio.h>
#include <linux/regmap.h>
#include <pcmcia/ss.h>
#include <mach/at91rm9200_mc.h>
#include <mach/at91_ramc.h>
/*
* A0..A10 work in each range; A23 indicates I/O space; A25 is CFRNW;
* some other bit in {A24,A22..A11} is nREG to flag memory access
......@@ -40,6 +39,8 @@
#define CF_IO_PHYS (1 << 23)
#define CF_MEM_PHYS (0x017ff800)
struct regmap *mc;
/*--------------------------------------------------------------------------*/
struct at91_cf_socket {
......@@ -155,10 +156,7 @@ static int at91_cf_set_io_map(struct pcmcia_socket *s, struct pccard_io_map *io)
/*
* Use 16 bit accesses unless/until we need 8-bit i/o space.
*/
csr = at91_ramc_read(0, AT91_SMC_CSR(cf->board->chipselect)) & ~AT91_SMC_DBW;
/*
*
* NOTE: this CF controller ignores IOIS16, so we can't really do
* MAP_AUTOSZ. The 16bit mode allows single byte access on either
* D0-D7 (even addr) or D8-D15 (odd), so it's close enough for many
......@@ -169,13 +167,14 @@ static int at91_cf_set_io_map(struct pcmcia_socket *s, struct pccard_io_map *io)
* CF 3.0 spec table 35 also giving the D8-D15 option.
*/
if (!(io->flags & (MAP_16BIT | MAP_AUTOSZ))) {
csr |= AT91_SMC_DBW_8;
csr = AT91_MC_SMC_DBW_8;
dev_dbg(&cf->pdev->dev, "8bit i/o bus\n");
} else {
csr |= AT91_SMC_DBW_16;
csr = AT91_MC_SMC_DBW_16;
dev_dbg(&cf->pdev->dev, "16bit i/o bus\n");
}
at91_ramc_write(0, AT91_SMC_CSR(cf->board->chipselect), csr);
regmap_update_bits(mc, AT91_MC_SMC_CSR(cf->board->chipselect),
AT91_MC_SMC_DBW, csr);
io->start = cf->socket.io_offset;
io->stop = io->start + SZ_2K - 1;
......@@ -236,6 +235,10 @@ static int at91_cf_dt_init(struct platform_device *pdev)
pdev->dev.platform_data = board;
mc = syscon_regmap_lookup_by_compatible("atmel,at91rm9200-sdramc");
if (IS_ERR(mc))
return PTR_ERR(mc);
return 0;
}
#else
......
/*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
*
* Memory Controllers (MC, EBI, SMC, SDRAMC, BFC) - System peripherals
* registers.
* Based on AT91RM9200 datasheet revision E.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#ifndef _LINUX_MFD_SYSCON_ATMEL_MC_H_
#define _LINUX_MFD_SYSCON_ATMEL_MC_H_
/* Memory Controller */
#define AT91_MC_RCR 0x00
#define AT91_MC_RCB BIT(0)
#define AT91_MC_ASR 0x04
#define AT91_MC_UNADD BIT(0)
#define AT91_MC_MISADD BIT(1)
#define AT91_MC_ABTSZ GENMASK(9, 8)
#define AT91_MC_ABTSZ_BYTE (0 << 8)
#define AT91_MC_ABTSZ_HALFWORD (1 << 8)
#define AT91_MC_ABTSZ_WORD (2 << 8)
#define AT91_MC_ABTTYP GENMASK(11, 10)
#define AT91_MC_ABTTYP_DATAREAD (0 << 10)
#define AT91_MC_ABTTYP_DATAWRITE (1 << 10)
#define AT91_MC_ABTTYP_FETCH (2 << 10)
#define AT91_MC_MST(n) BIT(16 + (n))
#define AT91_MC_SVMST(n) BIT(24 + (n))
#define AT91_MC_AASR 0x08
#define AT91_MC_MPR 0x0c
#define AT91_MPR_MSTP(n) GENMASK(2 + ((x) * 4), ((x) * 4))
/* External Bus Interface (EBI) registers */
#define AT91_MC_EBI_CSA 0x60
#define AT91_MC_EBI_CS(n) BIT(x)
#define AT91_MC_EBI_NUM_CS 8
#define AT91_MC_EBI_CFGR 0x64
#define AT91_MC_EBI_DBPUC BIT(0)
/* Static Memory Controller (SMC) registers */
#define AT91_MC_SMC_CSR(n) (0x70 + ((n) * 4))
#define AT91_MC_SMC_NWS GENMASK(6, 0)
#define AT91_MC_SMC_NWS_(x) ((x) << 0)
#define AT91_MC_SMC_WSEN BIT(7)
#define AT91_MC_SMC_TDF GENMASK(11, 8)
#define AT91_MC_SMC_TDF_(x) ((x) << 8)
#define AT91_MC_SMC_TDF_MAX 0xf
#define AT91_MC_SMC_BAT BIT(12)
#define AT91_MC_SMC_DBW GENMASK(14, 13)
#define AT91_MC_SMC_DBW_16 (1 << 13)
#define AT91_MC_SMC_DBW_8 (2 << 13)
#define AT91_MC_SMC_DPR BIT(15)
#define AT91_MC_SMC_ACSS GENMASK(17, 16)
#define AT91_MC_SMC_ACSS_(x) ((x) << 16)
#define AT91_MC_SMC_ACSS_MAX 3
#define AT91_MC_SMC_RWSETUP GENMASK(26, 24)
#define AT91_MC_SMC_RWSETUP_(x) ((x) << 24)
#define AT91_MC_SMC_RWHOLD GENMASK(30, 28)
#define AT91_MC_SMC_RWHOLD_(x) ((x) << 28)
#define AT91_MC_SMC_RWHOLDSETUP_MAX 7
/* SDRAM Controller registers */
#define AT91_MC_SDRAMC_MR 0x90
#define AT91_MC_SDRAMC_MODE GENMASK(3, 0)
#define AT91_MC_SDRAMC_MODE_NORMAL (0 << 0)
#define AT91_MC_SDRAMC_MODE_NOP (1 << 0)
#define AT91_MC_SDRAMC_MODE_PRECHARGE (2 << 0)
#define AT91_MC_SDRAMC_MODE_LMR (3 << 0)
#define AT91_MC_SDRAMC_MODE_REFRESH (4 << 0)
#define AT91_MC_SDRAMC_DBW_16 BIT(4)
#define AT91_MC_SDRAMC_TR 0x94
#define AT91_MC_SDRAMC_COUNT GENMASK(11, 0)
#define AT91_MC_SDRAMC_CR 0x98
#define AT91_MC_SDRAMC_NC GENMASK(1, 0)
#define AT91_MC_SDRAMC_NC_8 (0 << 0)
#define AT91_MC_SDRAMC_NC_9 (1 << 0)
#define AT91_MC_SDRAMC_NC_10 (2 << 0)
#define AT91_MC_SDRAMC_NC_11 (3 << 0)
#define AT91_MC_SDRAMC_NR GENMASK(3, 2)
#define AT91_MC_SDRAMC_NR_11 (0 << 2)
#define AT91_MC_SDRAMC_NR_12 (1 << 2)
#define AT91_MC_SDRAMC_NR_13 (2 << 2)
#define AT91_MC_SDRAMC_NB BIT(4)
#define AT91_MC_SDRAMC_NB_2 (0 << 4)
#define AT91_MC_SDRAMC_NB_4 (1 << 4)
#define AT91_MC_SDRAMC_CAS GENMASK(6, 5)
#define AT91_MC_SDRAMC_CAS_2 (2 << 5)
#define AT91_MC_SDRAMC_TWR GENMASK(10, 7)
#define AT91_MC_SDRAMC_TRC GENMASK(14, 11)
#define AT91_MC_SDRAMC_TRP GENMASK(18, 15)
#define AT91_MC_SDRAMC_TRCD GENMASK(22, 19)
#define AT91_MC_SDRAMC_TRAS GENMASK(26, 23)
#define AT91_MC_SDRAMC_TXSR GENMASK(30, 27)
#define AT91_MC_SDRAMC_SRR 0x9c
#define AT91_MC_SDRAMC_SRCB BIT(0)
#define AT91_MC_SDRAMC_LPR 0xa0
#define AT91_MC_SDRAMC_LPCB BIT(0)
#define AT91_MC_SDRAMC_IER 0xa4
#define AT91_MC_SDRAMC_IDR 0xa8
#define AT91_MC_SDRAMC_IMR 0xac
#define AT91_MC_SDRAMC_ISR 0xb0
#define AT91_MC_SDRAMC_RES BIT(0)
/* Burst Flash Controller register */
#define AT91_MC_BFC_MR 0xc0
#define AT91_MC_BFC_BFCOM GENMASK(1, 0)
#define AT91_MC_BFC_BFCOM_DISABLED (0 << 0)
#define AT91_MC_BFC_BFCOM_ASYNC (1 << 0)
#define AT91_MC_BFC_BFCOM_BURST (2 << 0)
#define AT91_MC_BFC_BFCC GENMASK(3, 2)
#define AT91_MC_BFC_BFCC_MCK (1 << 2)
#define AT91_MC_BFC_BFCC_DIV2 (2 << 2)
#define AT91_MC_BFC_BFCC_DIV4 (3 << 2)
#define AT91_MC_BFC_AVL GENMASK(7, 4)
#define AT91_MC_BFC_PAGES GENMASK(10, 8)
#define AT91_MC_BFC_PAGES_NO_PAGE (0 << 8)
#define AT91_MC_BFC_PAGES_16 (1 << 8)
#define AT91_MC_BFC_PAGES_32 (2 << 8)
#define AT91_MC_BFC_PAGES_64 (3 << 8)
#define AT91_MC_BFC_PAGES_128 (4 << 8)
#define AT91_MC_BFC_PAGES_256 (5 << 8)
#define AT91_MC_BFC_PAGES_512 (6 << 8)
#define AT91_MC_BFC_PAGES_1024 (7 << 8)
#define AT91_MC_BFC_OEL GENMASK(13, 12)
#define AT91_MC_BFC_BAAEN BIT(16)
#define AT91_MC_BFC_BFOEH BIT(17)
#define AT91_MC_BFC_MUXEN BIT(18)
#define AT91_MC_BFC_RDYEN BIT(19)
#endif /* _LINUX_MFD_SYSCON_ATMEL_MC_H_ */
/*
* arch/arm/mach-at91/include/mach/at91rm9200_sdramc.h
*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
*
* Memory Controllers (SDRAMC only) - System peripherals registers.
* Based on AT91RM9200 datasheet revision E.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#ifndef AT91RM9200_SDRAMC_H
#define AT91RM9200_SDRAMC_H
/* SDRAM Controller registers */
#define AT91RM9200_SDRAMC_MR 0x90 /* Mode Register */
#define AT91RM9200_SDRAMC_MODE (0xf << 0) /* Command Mode */
#define AT91RM9200_SDRAMC_MODE_NORMAL (0 << 0)
#define AT91RM9200_SDRAMC_MODE_NOP (1 << 0)
#define AT91RM9200_SDRAMC_MODE_PRECHARGE (2 << 0)
#define AT91RM9200_SDRAMC_MODE_LMR (3 << 0)
#define AT91RM9200_SDRAMC_MODE_REFRESH (4 << 0)
#define AT91RM9200_SDRAMC_DBW (1 << 4) /* Data Bus Width */
#define AT91RM9200_SDRAMC_DBW_32 (0 << 4)
#define AT91RM9200_SDRAMC_DBW_16 (1 << 4)
#define AT91RM9200_SDRAMC_TR 0x94 /* Refresh Timer Register */
#define AT91RM9200_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Count */
#define AT91RM9200_SDRAMC_CR 0x98 /* Configuration Register */
#define AT91RM9200_SDRAMC_NC (3 << 0) /* Number of Column Bits */
#define AT91RM9200_SDRAMC_NC_8 (0 << 0)
#define AT91RM9200_SDRAMC_NC_9 (1 << 0)
#define AT91RM9200_SDRAMC_NC_10 (2 << 0)
#define AT91RM9200_SDRAMC_NC_11 (3 << 0)
#define AT91RM9200_SDRAMC_NR (3 << 2) /* Number of Row Bits */
#define AT91RM9200_SDRAMC_NR_11 (0 << 2)
#define AT91RM9200_SDRAMC_NR_12 (1 << 2)
#define AT91RM9200_SDRAMC_NR_13 (2 << 2)
#define AT91RM9200_SDRAMC_NB (1 << 4) /* Number of Banks */
#define AT91RM9200_SDRAMC_NB_2 (0 << 4)
#define AT91RM9200_SDRAMC_NB_4 (1 << 4)
#define AT91RM9200_SDRAMC_CAS (3 << 5) /* CAS Latency */
#define AT91RM9200_SDRAMC_CAS_2 (2 << 5)
#define AT91RM9200_SDRAMC_TWR (0xf << 7) /* Write Recovery Delay */
#define AT91RM9200_SDRAMC_TRC (0xf << 11) /* Row Cycle Delay */
#define AT91RM9200_SDRAMC_TRP (0xf << 15) /* Row Precharge Delay */
#define AT91RM9200_SDRAMC_TRCD (0xf << 19) /* Row to Column Delay */
#define AT91RM9200_SDRAMC_TRAS (0xf << 23) /* Active to Precharge Delay */
#define AT91RM9200_SDRAMC_TXSR (0xf << 27) /* Exit Self Refresh to Active Delay */
#define AT91RM9200_SDRAMC_SRR 0x9c /* Self Refresh Register */
#define AT91RM9200_SDRAMC_LPR 0xa0 /* Low Power Register */
#define AT91RM9200_SDRAMC_IER 0xa4 /* Interrupt Enable Register */
#define AT91RM9200_SDRAMC_IDR 0xa8 /* Interrupt Disable Register */
#define AT91RM9200_SDRAMC_IMR 0xac /* Interrupt Mask Register */
#define AT91RM9200_SDRAMC_ISR 0xb0 /* Interrupt Status Register */
#endif
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册