wl12xx: AP mode config in ieee80211_ops.config

Separate configuration according to mode. AP has different rate
set configuration and no handling of idle-state.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Reviewed-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

drivers/net/wireless/wl12xx/main.c

@@ -1362,7 +1362,7 @@ static void wl1271_set_band_rate(struct wl1271 *wl)
 		wl->basic_rate_set = wl->conf.tx.basic_rate_5;
 }
 
-static int wl1271_handle_idle(struct wl1271 *wl, bool idle)
+static int wl1271_sta_handle_idle(struct wl1271 *wl, bool idle)
 {
 	int ret;
 
@@ -1403,14 +1403,17 @@ static int wl1271_op_config(struct ieee80211_hw *hw, u32 changed)
 	struct wl1271 *wl = hw->priv;
 	struct ieee80211_conf *conf = &hw->conf;
 	int channel, ret = 0;
+	bool is_ap;
 
 	channel = ieee80211_frequency_to_channel(conf->channel->center_freq);
 
-	wl1271_debug(DEBUG_MAC80211, "mac80211 config ch %d psm %s power %d %s",
+	wl1271_debug(DEBUG_MAC80211, "mac80211 config ch %d psm %s power %d %s"
+		     " changed 0x%x",
 		     channel,
 		     conf->flags & IEEE80211_CONF_PS ? "on" : "off",
 		     conf->power_level,
-		     conf->flags & IEEE80211_CONF_IDLE ? "idle" : "in use");
+		     conf->flags & IEEE80211_CONF_IDLE ? "idle" : "in use",
+			 changed);
 
 	/*
 	 * mac80211 will go to idle nearly immediately after transmitting some
@@ -1428,6 +1431,8 @@ static int wl1271_op_config(struct ieee80211_hw *hw, u32 changed)
 		goto out;
 	}
 
+	is_ap = (wl->bss_type == BSS_TYPE_AP_BSS);
+
 	ret = wl1271_ps_elp_wakeup(wl, false);
 	if (ret < 0)
 		goto out;
@@ -1439,31 +1444,34 @@ static int wl1271_op_config(struct ieee80211_hw *hw, u32 changed)
 		wl->band = conf->channel->band;
 		wl->channel = channel;
 
-		/*
-		 * FIXME: the mac80211 should really provide a fixed rate
-		 * to use here. for now, just use the smallest possible rate
-		 * for the band as a fixed rate for association frames and
-		 * other control messages.
-		 */
-		if (!test_bit(WL1271_FLAG_STA_ASSOCIATED, &wl->flags))
-			wl1271_set_band_rate(wl);
-
-		wl->basic_rate = wl1271_tx_min_rate_get(wl);
-		ret = wl1271_acx_sta_rate_policies(wl);
-		if (ret < 0)
-			wl1271_warning("rate policy for update channel "
-				       "failed %d", ret);
+		if (!is_ap) {
+			/*
+			 * FIXME: the mac80211 should really provide a fixed
+			 * rate to use here. for now, just use the smallest
+			 * possible rate for the band as a fixed rate for
+			 * association frames and other control messages.
+			 */
+			if (!test_bit(WL1271_FLAG_STA_ASSOCIATED, &wl->flags))
+				wl1271_set_band_rate(wl);
 
-		if (test_bit(WL1271_FLAG_JOINED, &wl->flags)) {
-			ret = wl1271_join(wl, false);
+			wl->basic_rate = wl1271_tx_min_rate_get(wl);
+			ret = wl1271_acx_sta_rate_policies(wl);
 			if (ret < 0)
-				wl1271_warning("cmd join to update channel "
+				wl1271_warning("rate policy for channel "
 					       "failed %d", ret);
+
+			if (test_bit(WL1271_FLAG_JOINED, &wl->flags)) {
+				ret = wl1271_join(wl, false);
+				if (ret < 0)
+					wl1271_warning("cmd join on channel "
+						       "failed %d", ret);
+			}
 		}
 	}
 
-	if (changed & IEEE80211_CONF_CHANGE_IDLE) {
-		ret = wl1271_handle_idle(wl, conf->flags & IEEE80211_CONF_IDLE);
+	if (changed & IEEE80211_CONF_CHANGE_IDLE && !is_ap) {
+		ret = wl1271_sta_handle_idle(wl,
+					conf->flags & IEEE80211_CONF_IDLE);
 		if (ret < 0)
 			wl1271_warning("idle mode change failed %d", ret);
 	}