net: dsa: LAN9303: add I2C managed mode support

In this mode the switch device and the internal phys will be managed via
I2C interface. The MDIO interface is still supported, but for the
(emulated) CPU port only.
Signed-off-by: NJuergen Borleis <jbe@pengutronix.de>
CC: devicetree@vger.kernel.org
CC: robh+dt@kernel.org
CC: mark.rutland@arm.com
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/dsa/lan9303.txt

+SMSC/MicroChip LAN9303 three port ethernet switch
+-------------------------------------------------
+
+Required properties:
+
+- compatible: should be "smsc,lan9303-i2c"
+
+Optional properties:
+
+- reset-gpios: GPIO to be used to reset the whole device
+- reset-duration: reset duration in milliseconds, defaults to 200 ms
+
+Subnodes:
+
+The integrated switch subnode should be specified according to the binding
+described in dsa/dsa.txt. The CPU port of this switch is always port 0.
+
+Note: always use 'reg = <0/1/2>;' for the three DSA ports, even if the device is
+configured to use 1/2/3 instead. This hardware configuration will be
+auto-detected and mapped accordingly.
+
+Example:
+
+I2C managed mode:
+
+	master: masterdevice@X {
+		status = "okay";
+
+		fixed-link { /* RMII fixed link to LAN9303 */
+			speed = <100>;
+			full-duplex;
+		};
+	};
+
+	switch: switch@a {
+		compatible = "smsc,lan9303-i2c";
+		reg = <0xa>;
+		status = "okay";
+		reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
+		reset-duration = <200>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 { /* RMII fixed link to master */
+				reg = <0>;
+				label = "cpu";
+				ethernet = <&master>;
+			};
+
+			port@1 { /* external port 1 */
+				reg = <1>;
+				label = "lan1;
+			};
+
+			port@2 { /* external port 2 */
+				reg = <2>;
+				label = "lan2";
+			};
+		};
+	};

drivers/net/dsa/Kconfig

@@ -50,4 +50,20 @@ config NET_DSA_MT7530
 	  This enables support for the Mediatek MT7530 Ethernet switch
 	  chip.
 
+config NET_DSA_SMSC_LAN9303
+	tristate
+	select NET_DSA_TAG_LAN9303
+	---help---
+	  This enables support for the SMSC/Microchip LAN9303 3 port ethernet
+	  switch chips.
+
+config NET_DSA_SMSC_LAN9303_I2C
+	tristate "SMSC/Microchip LAN9303 3-ports 10/100 ethernet switch in I2C managed mode"
+	depends on NET_DSA
+	select NET_DSA_SMSC_LAN9303
+	select REGMAP_I2C
+	---help---
+	  Enable access functions if the SMSC/Microchip LAN9303 is configured
+	  for I2C managed mode.
+
 endmenu

drivers/net/dsa/Makefile

@@ -3,6 +3,8 @@ obj-$(CONFIG_NET_DSA_BCM_SF2)	+= bcm-sf2.o
 bcm-sf2-objs			:= bcm_sf2.o bcm_sf2_cfp.o
 obj-$(CONFIG_NET_DSA_QCA8K)	+= qca8k.o
 obj-$(CONFIG_NET_DSA_MT7530)	+= mt7530.o
+obj-$(CONFIG_NET_DSA_SMSC_LAN9303) += lan9303-core.o
+obj-$(CONFIG_NET_DSA_SMSC_LAN9303_I2C) += lan9303_i2c.o
 obj-y				+= b53/
 obj-y				+= mv88e6xxx/
 obj-$(CONFIG_NET_DSA_LOOP)	+= dsa_loop.o dsa_loop_bdinfo.o

drivers/net/dsa/lan9303_i2c.c

+/*
+ * Copyright (C) 2017 Pengutronix, Juergen Borleis <kernel@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/of.h>
+
+#include "lan9303.h"
+
+struct lan9303_i2c {
+	struct i2c_client *device;
+	struct lan9303 chip;
+};
+
+static const struct regmap_config lan9303_i2c_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 32,
+	.reg_stride = 1,
+	.can_multi_write = true,
+	.max_register = 0x0ff, /* address bits 0..1 are not used */
+	.reg_format_endian = REGMAP_ENDIAN_LITTLE,
+
+	.volatile_table = &lan9303_register_set,
+	.wr_table = &lan9303_register_set,
+	.rd_table = &lan9303_register_set,
+
+	.cache_type = REGCACHE_NONE,
+};
+
+static int lan9303_i2c_probe(struct i2c_client *client,
+			     const struct i2c_device_id *id)
+{
+	struct lan9303_i2c *sw_dev;
+	int ret;
+
+	sw_dev = devm_kzalloc(&client->dev, sizeof(struct lan9303_i2c),
+			      GFP_KERNEL);
+	if (!sw_dev)
+		return -ENOMEM;
+
+	sw_dev->chip.regmap = devm_regmap_init_i2c(client,
+						&lan9303_i2c_regmap_config);
+	if (IS_ERR(sw_dev->chip.regmap)) {
+		ret = PTR_ERR(sw_dev->chip.regmap);
+		dev_err(&client->dev, "Failed to allocate register map: %d\n",
+			ret);
+		return ret;
+	}
+
+	/* link forward and backward */
+	sw_dev->device = client;
+	i2c_set_clientdata(client, sw_dev);
+	sw_dev->chip.dev = &client->dev;
+
+	ret = lan9303_probe(&sw_dev->chip, client->dev.of_node);
+	if (ret != 0)
+		return ret;
+
+	dev_info(&client->dev, "LAN9303 I2C driver loaded successfully\n");
+
+	return 0;
+}
+
+static int lan9303_i2c_remove(struct i2c_client *client)
+{
+	struct lan9303_i2c *sw_dev;
+
+	sw_dev = i2c_get_clientdata(client);
+	if (!sw_dev)
+		return -ENODEV;
+
+	return lan9303_remove(&sw_dev->chip);
+}
+
+/*-------------------------------------------------------------------------*/
+
+static const struct i2c_device_id lan9303_i2c_id[] = {
+	{ "lan9303", 0 },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(i2c, lan9303_i2c_id);
+
+static const struct of_device_id lan9303_i2c_of_match[] = {
+	{ .compatible = "smsc,lan9303-i2c", },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, lan9303_i2c_of_match);
+
+static struct i2c_driver lan9303_i2c_driver = {
+	.driver = {
+		.name = "LAN9303_I2C",
+		.of_match_table = of_match_ptr(lan9303_i2c_of_match),
+	},
+	.probe = lan9303_i2c_probe,
+	.remove = lan9303_i2c_remove,
+	.id_table = lan9303_i2c_id,
+};
+module_i2c_driver(lan9303_i2c_driver);
+
+MODULE_AUTHOR("Juergen Borleis <kernel@pengutronix.de>");
+MODULE_DESCRIPTION("Driver for SMSC/Microchip LAN9303 three port ethernet switch in I2C managed mode");
+MODULE_LICENSE("GPL v2");