ARM: sun7i: cubieboard2: Convert to DT label based syntax

In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

arch/arm/boot/dts/sun7i-a20-cubieboard2.dts

@@ -59,96 +59,6 @@
 	model = "Cubietech Cubieboard2";
 	compatible = "cubietech,cubieboard2", "allwinner,sun7i-a20";
 
-	soc@01c00000 {
-		mmc0: mmc@01c0f000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
-			vmmc-supply = <&reg_vcc3v3>;
-			bus-width = <4>;
-			cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
-			cd-inverted;
-			status = "okay";
-		};
-
-		usbphy: phy@01c13400 {
-			usb1_vbus-supply = <&reg_usb1_vbus>;
-			usb2_vbus-supply = <&reg_usb2_vbus>;
-			status = "okay";
-		};
-
-		ehci0: usb@01c14000 {
-			status = "okay";
-		};
-
-		ohci0: usb@01c14400 {
-			status = "okay";
-		};
-
-		ahci: sata@01c18000 {
-			target-supply = <&reg_ahci_5v>;
-			status = "okay";
-		};
-
-		ehci1: usb@01c1c000 {
-			status = "okay";
-		};
-
-		ohci1: usb@01c1c400 {
-			status = "okay";
-		};
-
-		pinctrl@01c20800 {
-			led_pins_cubieboard2: led_pins@0 {
-				allwinner,pins = "PH20", "PH21";
-				allwinner,function = "gpio_out";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-		};
-
-		ir0: ir@01c21800 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&ir0_pins_a>;
-			status = "okay";
-		};
-
-		uart0: serial@01c28000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart0_pins_a>;
-			status = "okay";
-		};
-
-		i2c0: i2c@01c2ac00 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c0_pins_a>;
-			status = "okay";
-
-			axp209: pmic@34 {
-				reg = <0x34>;
-				interrupt-parent = <&nmi_intc>;
-				interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-			};
-		};
-
-		i2c1: i2c@01c2b000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c1_pins_a>;
-			status = "okay";
-		};
-
-		gmac: ethernet@01c50000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&gmac_pins_mii_a>;
-			phy = <&phy1>;
-			phy-mode = "mii";
-			status = "okay";
-
-			phy1: ethernet-phy@1 {
-				reg = <1>;
-			};
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -164,26 +74,94 @@
 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
 		};
 	};
+};
 
-	reg_ahci_5v: ahci-5v {
-		status = "okay";
-	};
+&ahci {
+	target-supply = <&reg_ahci_5v>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
 
-	reg_usb1_vbus: usb1-vbus {
-		status = "okay";
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_pins_mii_a>;
+	phy = <&phy1>;
+	phy-mode = "mii";
+	status = "okay";
+
+	phy1: ethernet-phy@1 {
+		reg = <1>;
 	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
 
-	reg_usb2_vbus: usb2-vbus {
-		status = "okay";
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 	};
 };
 
-#include "axp209.dtsi"
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
 
-&cpu0 {
-	cpu-supply = <&reg_dcdc2>;
+&ir0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir0_pins_a>;
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+	cd-inverted;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
 };
 
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	led_pins_cubieboard2: led_pins@0 {
+		allwinner,pins = "PH20", "PH21";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+};
+
+&reg_ahci_5v {
+	status = "okay";
+};
+
+#include "axp209.dtsi"
+
 &reg_dcdc2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1000000>;
@@ -208,3 +186,23 @@
 	regulator-max-microvolt = <3000000>;
 	regulator-name = "avcc";
 };
+
+&reg_usb1_vbus {
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};