提交 b2d1eee1 编写于 作者: M Mikael Pettersson 提交者: Jeff Garzik

[PATCH] sata_promise fixes and updates

This patch updates the sata_promise driver as follows:
- Correct typo in definition of PDC_TBG_MODE: it's at 0x41C not 0x41
  in first-generation chips. This error caused PCI access alignment
  exceptions on SPARC64, and on all platforms it disabled the expected
  initialisation of TBG mode.
- Add flags field to struct pdc_host_priv. Define PDC_FLAG_GEN_II
  and use it to distinguish first- and second-generation chips.
- Prevent the FLASH_CTL FIFO_SHD bit from being set to 1 on second-
  generation chips. This matches Promises' ulsata2 driver.
- Prevent TBG mode and SLEW rate initialisation in second-generation chips.
  These two registers have moved, TBG mode has been redefined, and
  Promise's ulsata2 driver no longer attempts to initialise them.
- Correct PCI device table so devices 0x3570, 0x3571, and 0x3d73 are
  marked as 2057x (2nd gen) not 2037x (1st gen).
- Correct PCI device table so device 0x3d17 is marked as 40518
  (2nd gen 4 ports) not 20319 (1st gen 4 ports).
- Correct pdc_ata_init_one() to treat 20771 as a second-generation chip.

Tested on 0x3d75 (2nd gen), 0x3d73 (2nd gen), and 0x3373 (1st gen) chips.
The information comes from the newly uploaded Promise SATA HW specs,
Promise's ultra and ulsata2 drivers, and debugging on 3d75/3d73/3373 chips.

hp->hotplug_offset could now be removed and its value recomputed
in pdc_host_init() using hp->flags, but that would be a cleanup
not a functional change, so I'm ignoring it for now.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
上级 46b027cc
......@@ -52,13 +52,13 @@
enum {
PDC_PKT_SUBMIT = 0x40, /* Command packet pointer addr */
PDC_INT_SEQMASK = 0x40, /* Mask of asserted SEQ INTs */
PDC_TBG_MODE = 0x41C, /* TBG mode */
PDC_FLASH_CTL = 0x44, /* Flash control register */
PDC_GLOBAL_CTL = 0x48, /* Global control/status (per port) */
PDC_CTLSTAT = 0x60, /* IDE control and status (per port) */
PDC_SATA_PLUG_CSR = 0x6C, /* SATA Plug control/status reg */
PDC2_SATA_PLUG_CSR = 0x60, /* SATAII Plug control/status reg */
PDC_SLEW_CTL = 0x470, /* slew rate control reg */
PDC_TBG_MODE = 0x41C, /* TBG mode (not SATAII) */
PDC_SLEW_CTL = 0x470, /* slew rate control reg (not SATAII) */
PDC_ERR_MASK = (1<<19) | (1<<20) | (1<<21) | (1<<22) |
(1<<8) | (1<<9) | (1<<10),
......@@ -77,6 +77,9 @@ enum {
PDC_COMMON_FLAGS = ATA_FLAG_NO_LEGACY | ATA_FLAG_SRST |
ATA_FLAG_MMIO | ATA_FLAG_NO_ATAPI |
ATA_FLAG_PIO_POLLING,
/* hp->flags bits */
PDC_FLAG_GEN_II = (1 << 0),
};
......@@ -86,6 +89,7 @@ struct pdc_port_priv {
};
struct pdc_host_priv {
unsigned long flags;
int hotplug_offset;
};
......@@ -234,20 +238,20 @@ static const struct ata_port_info pdc_port_info[] = {
static const struct pci_device_id pdc_ata_pci_tbl[] = {
{ PCI_VDEVICE(PROMISE, 0x3371), board_2037x },
{ PCI_VDEVICE(PROMISE, 0x3570), board_2037x },
{ PCI_VDEVICE(PROMISE, 0x3571), board_2037x },
{ PCI_VDEVICE(PROMISE, 0x3373), board_2037x },
{ PCI_VDEVICE(PROMISE, 0x3375), board_2037x },
{ PCI_VDEVICE(PROMISE, 0x3376), board_2037x },
{ PCI_VDEVICE(PROMISE, 0x3570), board_2057x },
{ PCI_VDEVICE(PROMISE, 0x3571), board_2057x },
{ PCI_VDEVICE(PROMISE, 0x3574), board_2057x },
{ PCI_VDEVICE(PROMISE, 0x3d73), board_2057x },
{ PCI_VDEVICE(PROMISE, 0x3d75), board_2057x },
{ PCI_VDEVICE(PROMISE, 0x3d73), board_2037x },
{ PCI_VDEVICE(PROMISE, 0x3318), board_20319 },
{ PCI_VDEVICE(PROMISE, 0x3319), board_20319 },
{ PCI_VDEVICE(PROMISE, 0x3515), board_20319 },
{ PCI_VDEVICE(PROMISE, 0x3519), board_20319 },
{ PCI_VDEVICE(PROMISE, 0x3d17), board_20319 },
{ PCI_VDEVICE(PROMISE, 0x3d17), board_40518 },
{ PCI_VDEVICE(PROMISE, 0x3d18), board_40518 },
{ PCI_VDEVICE(PROMISE, 0x6629), board_20619 },
......@@ -639,9 +643,11 @@ static void pdc_host_init(unsigned int chip_id, struct ata_probe_ent *pe)
* "TODO: figure out why we do this"
*/
/* change FIFO_SHD to 8 dwords, enable BMR_BURST */
/* enable BMR_BURST, maybe change FIFO_SHD to 8 dwords */
tmp = readl(mmio + PDC_FLASH_CTL);
tmp |= 0x12000; /* bit 16 (fifo 8 dw) and 13 (bmr burst?) */
tmp |= 0x02000; /* bit 13 (enable bmr burst) */
if (!(hp->flags & PDC_FLAG_GEN_II))
tmp |= 0x10000; /* bit 16 (fifo threshold at 8 dw) */
writel(tmp, mmio + PDC_FLASH_CTL);
/* clear plug/unplug flags for all ports */
......@@ -652,6 +658,10 @@ static void pdc_host_init(unsigned int chip_id, struct ata_probe_ent *pe)
tmp = readl(mmio + hotplug_offset);
writel(tmp | 0xff0000, mmio + hotplug_offset);
/* don't initialise TBG or SLEW on 2nd generation chips */
if (hp->flags & PDC_FLAG_GEN_II)
return;
/* reduce TBG clock to 133 Mhz. */
tmp = readl(mmio + PDC_TBG_MODE);
tmp &= ~0x30000; /* clear bit 17, 16*/
......@@ -745,6 +755,7 @@ static int pdc_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *e
/* notice 4-port boards */
switch (board_idx) {
case board_40518:
hp->flags |= PDC_FLAG_GEN_II;
/* Override hotplug offset for SATAII150 */
hp->hotplug_offset = PDC2_SATA_PLUG_CSR;
/* Fall through */
......@@ -758,15 +769,14 @@ static int pdc_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *e
probe_ent->port[3].scr_addr = base + 0x700;
break;
case board_2057x:
case board_20771:
hp->flags |= PDC_FLAG_GEN_II;
/* Override hotplug offset for SATAII150 */
hp->hotplug_offset = PDC2_SATA_PLUG_CSR;
/* Fall through */
case board_2037x:
probe_ent->n_ports = 2;
break;
case board_20771:
probe_ent->n_ports = 2;
break;
case board_20619:
probe_ent->n_ports = 4;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册