cxgb4: add tc flower match support for vlan

Add support for matching on vlan tci.  Construct vlan tci match param
based on vlan-id and vlan-pcp values supplied by tc.
Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_flower.c

@@ -160,6 +160,40 @@ static void cxgb4_process_flow_match(struct net_device *dev,
 		fs->mask.tos = mask->tos;
 	}
 
+	if (dissector_uses_key(cls->dissector, FLOW_DISSECTOR_KEY_VLAN)) {
+		struct flow_dissector_key_vlan *key, *mask;
+		u16 vlan_tci, vlan_tci_mask;
+
+		key = skb_flow_dissector_target(cls->dissector,
+						FLOW_DISSECTOR_KEY_VLAN,
+						cls->key);
+		mask = skb_flow_dissector_target(cls->dissector,
+						 FLOW_DISSECTOR_KEY_VLAN,
+						 cls->mask);
+		vlan_tci = key->vlan_id | (key->vlan_priority <<
+					   VLAN_PRIO_SHIFT);
+		vlan_tci_mask = mask->vlan_id | (mask->vlan_priority <<
+						 VLAN_PRIO_SHIFT);
+		fs->val.ivlan = cpu_to_be16(vlan_tci);
+		fs->mask.ivlan = cpu_to_be16(vlan_tci_mask);
+
+		/* Chelsio adapters use ivlan_vld bit to match vlan packets
+		 * as 802.1Q. Also, when vlan tag is present in packets,
+		 * ethtype match is used then to match on ethtype of inner
+		 * header ie. the header following the vlan header.
+		 * So, set the ivlan_vld based on ethtype info supplied by
+		 * TC for vlan packets if its 802.1Q. And then reset the
+		 * ethtype value else, hw will try to match the supplied
+		 * ethtype value with ethtype of inner header.
+		 */
+		if (fs->val.ethtype == ETH_P_8021Q) {
+			fs->val.ivlan_vld = 1;
+			fs->mask.ivlan_vld = 1;
+			fs->val.ethtype = 0;
+			fs->mask.ethtype = 0;
+		}
+	}
+
 	/* Match only packets coming from the ingress port where this
 	 * filter will be created.
 	 */
@@ -179,6 +213,7 @@ static int cxgb4_validate_flow_match(struct net_device *dev,
 	      BIT(FLOW_DISSECTOR_KEY_IPV4_ADDRS) |
 	      BIT(FLOW_DISSECTOR_KEY_IPV6_ADDRS) |
 	      BIT(FLOW_DISSECTOR_KEY_PORTS) |
+	      BIT(FLOW_DISSECTOR_KEY_VLAN) |
 	      BIT(FLOW_DISSECTOR_KEY_IP))) {
 		netdev_warn(dev, "Unsupported key used: 0x%x\n",
 			    cls->dissector->used_keys);