提交 ad24b0da 编写于 作者: J Johannes Berg 提交者: Johannes Berg

wireless: indent kernel-doc with tabs

Almost everywhere tabs are used to indent continuation
lines, replace the few places that use spaces.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
上级 822854b0
......@@ -490,7 +490,7 @@ enum survey_info_flags {
* @channel: the channel this survey record reports, mandatory
* @filled: bitflag of flags from &enum survey_info_flags
* @noise: channel noise in dBm. This and all following fields are
* optional
* optional
* @channel_time: amount of time in ms the radio spent on the channel
* @channel_time_busy: amount of time the primary channel was sensed busy
* @channel_time_ext_busy: amount of time the extension channel was sensed busy
......@@ -546,9 +546,9 @@ struct cfg80211_crypto_settings {
/**
* struct cfg80211_beacon_data - beacon data
* @head: head portion of beacon (before TIM IE)
* or %NULL if not changed
* or %NULL if not changed
* @tail: tail portion of beacon (after TIM IE)
* or %NULL if not changed
* or %NULL if not changed
* @head_len: length of @head
* @tail_len: length of @tail
* @beacon_ies: extra information element(s) to add into Beacon frames or %NULL
......@@ -764,7 +764,7 @@ int cfg80211_check_station_change(struct wiphy *wiphy,
* @STATION_INFO_PLINK_STATE: @plink_state filled
* @STATION_INFO_SIGNAL: @signal filled
* @STATION_INFO_TX_BITRATE: @txrate fields are filled
* (tx_bitrate, tx_bitrate_flags and tx_bitrate_mcs)
* (tx_bitrate, tx_bitrate_flags and tx_bitrate_mcs)
* @STATION_INFO_RX_PACKETS: @rx_packets filled with 32-bit value
* @STATION_INFO_TX_PACKETS: @tx_packets filled with 32-bit value
* @STATION_INFO_TX_RETRIES: @tx_retries filled
......@@ -1509,7 +1509,7 @@ enum cfg80211_assoc_req_flags {
* @prev_bssid: previous BSSID, if not %NULL use reassociate frame
* @flags: See &enum cfg80211_assoc_req_flags
* @ht_capa: HT Capabilities over-rides. Values set in ht_capa_mask
* will be used in ht_capa. Un-supported values will be ignored.
* will be used in ht_capa. Un-supported values will be ignored.
* @ht_capa_mask: The bits of ht_capa which are to be used.
* @vht_capa: VHT capability override
* @vht_capa_mask: VHT capability mask indicating which fields to use
......@@ -1593,7 +1593,7 @@ struct cfg80211_disassoc_request {
* @basic_rates: bitmap of basic rates to use when creating the IBSS
* @mcast_rate: per-band multicast rate index + 1 (0: disabled)
* @ht_capa: HT Capabilities over-rides. Values set in ht_capa_mask
* will be used in ht_capa. Un-supported values will be ignored.
* will be used in ht_capa. Un-supported values will be ignored.
* @ht_capa_mask: The bits of ht_capa which are to be used.
*/
struct cfg80211_ibss_params {
......@@ -1635,9 +1635,9 @@ struct cfg80211_ibss_params {
* @key: WEP key for shared key authentication
* @flags: See &enum cfg80211_assoc_req_flags
* @bg_scan_period: Background scan period in seconds
* or -1 to indicate that default value is to be used.
* or -1 to indicate that default value is to be used.
* @ht_capa: HT Capabilities over-rides. Values set in ht_capa_mask
* will be used in ht_capa. Un-supported values will be ignored.
* will be used in ht_capa. Un-supported values will be ignored.
* @ht_capa_mask: The bits of ht_capa which are to be used.
* @vht_capa: VHT Capability overrides
* @vht_capa_mask: The bits of vht_capa which are to be used.
......
......@@ -1004,11 +1004,11 @@ enum ieee80211_smps_mode {
* @radar_enabled: whether radar detection is enabled
*
* @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
* (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
* but actually means the number of transmissions not the number of retries
* (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
* but actually means the number of transmissions not the number of retries
* @short_frame_max_tx_count: Maximum number of transmissions for a "short"
* frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
* number of transmissions not the number of retries
* frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
* number of transmissions not the number of retries
*
* @smps_mode: spatial multiplexing powersave mode; note that
* %IEEE80211_SMPS_STATIC is used when the device is not
......@@ -1092,7 +1092,7 @@ enum ieee80211_vif_flags {
* be off when it is %NULL there can still be races and packets could be
* processed after it switches back to %NULL.
* @debugfs_dir: debugfs dentry, can be used by drivers to create own per
* interface debug files. Note that it will be NULL for the virtual
* interface debug files. Note that it will be NULL for the virtual
* monitor interface (if that is requested.)
* @drv_priv: data area for driver use, will always be aligned to
* sizeof(void *).
......@@ -1425,10 +1425,10 @@ struct ieee80211_tx_control {
* the stack.
*
* @IEEE80211_HW_CONNECTION_MONITOR:
* The hardware performs its own connection monitoring, including
* periodic keep-alives to the AP and probing the AP on beacon loss.
* When this flag is set, signaling beacon-loss will cause an immediate
* change to disassociated state.
* The hardware performs its own connection monitoring, including
* periodic keep-alives to the AP and probing the AP on beacon loss.
* When this flag is set, signaling beacon-loss will cause an immediate
* change to disassociated state.
*
* @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC:
* This device needs to get data from beacon before association (i.e.
......@@ -1526,10 +1526,10 @@ enum ieee80211_hw_flags {
* @channel_change_time: time (in microseconds) it takes to change channels.
*
* @max_signal: Maximum value for signal (rssi) in RX information, used
* only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
* only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
*
* @max_listen_interval: max listen interval in units of beacon interval
* that HW supports
* that HW supports
*
* @queues: number of available hardware transmit queues for
* data packets. WMM/QoS requires at least four, these
......@@ -2443,7 +2443,7 @@ enum ieee80211_roc_type {
* The callback can sleep.
*
* @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
* Currently, this is only used for IBSS mode debugging. Is not a
* Currently, this is only used for IBSS mode debugging. Is not a
* required function.
* The callback can sleep.
*
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册