提交 aa4f6084 编写于 作者: L Linus Torvalds

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k

Pull m68k fix from Geert Uytterhoeven:
 "A boot lock-up on Mac, also destined for stable"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k/mac: Fix unexpected interrupt with CONFIG_EARLY_PRINTK
......@@ -2752,11 +2752,9 @@ func_return get_new_page
#ifdef CONFIG_MAC
L(scc_initable_mac):
.byte 9,12 /* Reset */
.byte 4,0x44 /* x16, 1 stopbit, no parity */
.byte 3,0xc0 /* receiver: 8 bpc */
.byte 5,0xe2 /* transmitter: 8 bpc, assert dtr/rts */
.byte 9,0 /* no interrupts */
.byte 10,0 /* NRZ */
.byte 11,0x50 /* use baud rate generator */
.byte 12,1,13,0 /* 38400 baud */
......@@ -2899,6 +2897,7 @@ func_start serial_init,%d0/%d1/%a0/%a1
is_not_mac(L(serial_init_not_mac))
#ifdef SERIAL_DEBUG
/* You may define either or both of these. */
#define MAC_USE_SCC_A /* Modem port */
#define MAC_USE_SCC_B /* Printer port */
......@@ -2908,9 +2907,21 @@ func_start serial_init,%d0/%d1/%a0/%a1
#define mac_scc_cha_b_data_offset 0x4
#define mac_scc_cha_a_data_offset 0x6
#if defined(MAC_USE_SCC_A) || defined(MAC_USE_SCC_B)
movel %pc@(L(mac_sccbase)),%a0
/* Reset SCC device */
moveb #9,%a0@(mac_scc_cha_a_ctrl_offset)
moveb #0xc0,%a0@(mac_scc_cha_a_ctrl_offset)
/* Wait for 5 PCLK cycles, which is about 68 CPU cycles */
/* 5 / 3.6864 MHz = approx. 1.36 us = 68 / 50 MHz */
movel #35,%d0
5:
subq #1,%d0
jne 5b
#endif
#ifdef MAC_USE_SCC_A
/* Initialize channel A */
movel %pc@(L(mac_sccbase)),%a0
lea %pc@(L(scc_initable_mac)),%a1
5: moveb %a1@+,%d0
jmi 6f
......@@ -2922,9 +2933,6 @@ func_start serial_init,%d0/%d1/%a0/%a1
#ifdef MAC_USE_SCC_B
/* Initialize channel B */
#ifndef MAC_USE_SCC_A /* Load mac_sccbase only if needed */
movel %pc@(L(mac_sccbase)),%a0
#endif /* MAC_USE_SCC_A */
lea %pc@(L(scc_initable_mac)),%a1
7: moveb %a1@+,%d0
jmi 8f
......@@ -2933,6 +2941,7 @@ func_start serial_init,%d0/%d1/%a0/%a1
jra 7b
8:
#endif /* MAC_USE_SCC_B */
#endif /* SERIAL_DEBUG */
jra L(serial_init_done)
......@@ -3006,17 +3015,17 @@ func_start serial_putc,%d0/%d1/%a0/%a1
#ifdef SERIAL_DEBUG
#ifdef MAC_USE_SCC_A
#if defined(MAC_USE_SCC_A) || defined(MAC_USE_SCC_B)
movel %pc@(L(mac_sccbase)),%a1
#endif
#ifdef MAC_USE_SCC_A
3: btst #2,%a1@(mac_scc_cha_a_ctrl_offset)
jeq 3b
moveb %d0,%a1@(mac_scc_cha_a_data_offset)
#endif /* MAC_USE_SCC_A */
#ifdef MAC_USE_SCC_B
#ifndef MAC_USE_SCC_A /* Load mac_sccbase only if needed */
movel %pc@(L(mac_sccbase)),%a1
#endif /* MAC_USE_SCC_A */
4: btst #2,%a1@(mac_scc_cha_b_ctrl_offset)
jeq 4b
moveb %d0,%a1@(mac_scc_cha_b_data_offset)
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册