提交 a8e8b7ff 编写于 作者: S Salil 提交者: David S. Miller

net: hns3: Add support to change MTU in HNS3 hardware

This patch adds the following support to the HNS3 driver:
1. Support to change the Maximum Transmission Unit of a
   port in the HNS NIC hardware.
2. Initializes the supported MTU range for the netdevice.
Signed-off-by: Nlipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 06552f8e
......@@ -1278,11 +1278,42 @@ static int hns3_ndo_set_vf_vlan(struct net_device *netdev, int vf, u16 vlan,
return ret;
}
static int hns3_nic_change_mtu(struct net_device *netdev, int new_mtu)
{
struct hns3_nic_priv *priv = netdev_priv(netdev);
struct hnae3_handle *h = priv->ae_handle;
bool if_running = netif_running(netdev);
int ret;
if (!h->ae_algo->ops->set_mtu)
return -EOPNOTSUPP;
/* if this was called with netdev up then bring netdevice down */
if (if_running) {
(void)hns3_nic_net_stop(netdev);
msleep(100);
}
ret = h->ae_algo->ops->set_mtu(h, new_mtu);
if (ret) {
netdev_err(netdev, "failed to change MTU in hardware %d\n",
ret);
return ret;
}
/* if the netdev was running earlier, bring it up again */
if (if_running && hns3_nic_net_open(netdev))
ret = -EINVAL;
return ret;
}
static const struct net_device_ops hns3_nic_netdev_ops = {
.ndo_open = hns3_nic_net_open,
.ndo_stop = hns3_nic_net_stop,
.ndo_start_xmit = hns3_nic_net_xmit,
.ndo_set_mac_address = hns3_nic_net_set_mac_address,
.ndo_change_mtu = hns3_nic_change_mtu,
.ndo_set_features = hns3_nic_set_features,
.ndo_get_stats64 = hns3_nic_get_stats64,
.ndo_setup_tc = hns3_nic_setup_tc,
......@@ -2752,6 +2783,9 @@ static int hns3_client_init(struct hnae3_handle *handle)
goto out_reg_netdev_fail;
}
/* MTU range: (ETH_MIN_MTU(kernel default) - 9706) */
netdev->max_mtu = HNS3_MAX_MTU - (ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN);
return ret;
out_reg_netdev_fail:
......
......@@ -76,6 +76,7 @@ enum hns3_nic_state {
#define HNS3_RING_NAME_LEN 16
#define HNS3_BUFFER_SIZE_2048 2048
#define HNS3_RING_MAX_PENDING 32768
#define HNS3_MAX_MTU 9728
#define HNS3_BD_SIZE_512_TYPE 0
#define HNS3_BD_SIZE_1024_TYPE 1
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册