提交 a7f61fa4 编写于 作者: G Greg Ungerer 提交者: Linus Torvalds

m68knommu: switch ColdFire TIMER to use GENERIC_TIME

Switch the ColdFire TIMER timer to use GENERIC_TIME.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
上级 8d80c5ee
......@@ -3,7 +3,7 @@
/*
* timers.c -- generic ColdFire hardware timer support.
*
* Copyright (C) 1999-2007, Greg Ungerer (gerg@snapgear.com)
* Copyright (C) 1999-2008, Greg Ungerer <gerg@snapgear.com>
*/
/***************************************************************************/
......@@ -13,6 +13,8 @@
#include <linux/sched.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/profile.h>
#include <linux/clocksource.h>
#include <asm/io.h>
#include <asm/traps.h>
#include <asm/machdep.h>
......@@ -25,6 +27,7 @@
/*
* By default use timer1 as the system clock timer.
*/
#define FREQ (MCF_BUSCLK / 16)
#define TA(a) (MCF_MBAR + MCFTIMER_BASE1 + (a))
/*
......@@ -41,7 +44,7 @@ unsigned int mcf_timerlevel = 5;
* Unfortunately it is a little different on each ColdFire.
*/
extern void mcf_settimericr(int timer, int level);
extern int mcf_timerirqpending(int timer);
void coldfire_profile_init(void);
#if defined(CONFIG_M532x)
#define __raw_readtrr __raw_readl
......@@ -51,38 +54,70 @@ extern int mcf_timerirqpending(int timer);
#define __raw_writetrr __raw_writew
#endif
static u32 mcftmr_cycles_per_jiffy;
static u32 mcftmr_cnt;
/***************************************************************************/
static irqreturn_t hw_tick(int irq, void *dummy)
static irqreturn_t mcftmr_tick(int irq, void *dummy)
{
/* Reset the ColdFire timer */
__raw_writeb(MCFTIMER_TER_CAP | MCFTIMER_TER_REF, TA(MCFTIMER_TER));
mcftmr_cnt += mcftmr_cycles_per_jiffy;
return arch_timer_interrupt(irq, dummy);
}
/***************************************************************************/
static struct irqaction coldfire_timer_irq = {
static struct irqaction mcftmr_timer_irq = {
.name = "timer",
.flags = IRQF_DISABLED | IRQF_TIMER,
.handler = hw_tick,
.handler = mcftmr_tick,
};
/***************************************************************************/
static int ticks_per_intr;
static cycle_t mcftmr_read_clk(void)
{
unsigned long flags;
u32 cycles;
u16 tcn;
local_irq_save(flags);
tcn = __raw_readw(TA(MCFTIMER_TCN));
cycles = mcftmr_cnt;
local_irq_restore(flags);
return cycles + tcn;
}
/***************************************************************************/
static struct clocksource mcftmr_clk = {
.name = "tmr",
.rating = 250,
.read = mcftmr_read_clk,
.shift = 20,
.mask = CLOCKSOURCE_MASK(32),
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
};
/***************************************************************************/
void hw_timer_init(void)
{
setup_irq(mcf_timervector, &coldfire_timer_irq);
setup_irq(mcf_timervector, &mcftmr_timer_irq);
__raw_writew(MCFTIMER_TMR_DISABLE, TA(MCFTIMER_TMR));
ticks_per_intr = (MCF_BUSCLK / 16) / HZ;
__raw_writetrr(ticks_per_intr - 1, TA(MCFTIMER_TRR));
mcftmr_cycles_per_jiffy = FREQ / HZ;
__raw_writetrr(mcftmr_cycles_per_jiffy, TA(MCFTIMER_TRR));
__raw_writew(MCFTIMER_TMR_ENORI | MCFTIMER_TMR_CLK16 |
MCFTIMER_TMR_RESTART | MCFTIMER_TMR_ENABLE, TA(MCFTIMER_TMR));
mcftmr_clk.mult = clocksource_hz2mult(FREQ, mcftmr_clk.shift);
clocksource_register(&mcftmr_clk);
mcf_settimericr(1, mcf_timerlevel);
#ifdef CONFIG_HIGHPROFILE
......@@ -90,21 +125,6 @@ void hw_timer_init(void)
#endif
}
/***************************************************************************/
unsigned long hw_timer_offset(void)
{
unsigned long tcn, offset;
tcn = __raw_readw(TA(MCFTIMER_TCN));
offset = ((tcn + 1) * (1000000 / HZ)) / ticks_per_intr;
/* Check if we just wrapped the counters and maybe missed a tick */
if ((offset < (1000000 / HZ / 2)) && mcf_timerirqpending(1))
offset += 1000000 / HZ;
return offset;
}
/***************************************************************************/
#ifdef CONFIG_HIGHPROFILE
/***************************************************************************/
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册