Merge branches 'pci/misc', 'pci/pm', 'pci/host-designware', 'pci/host-imx6',...

Merge branches 'pci/misc', 'pci/pm', 'pci/host-designware', 'pci/host-imx6', 'pci/host-keystone', 'pci/host-tegra' and 'pci/host-xilinx' into next

* pci/misc:
  PCI/AER: Make <linux/aer.h> standalone includable
  PCI: Remove unnecessary variable in pci_add_dynid()

* pci/pm:
  PCI/PM: Allow PCI devices to be put into D3cold during system suspend
  PCI/PM: Drop unused runtime PM support code for PCIe ports

* pci/host-designware:
  PCI: designware: Check private_data validity in single place
  PCI: designware: Remove pci_assign_unassigned_resources() from dw_pcie_host_init()
  PCI: designware: Use pci_create_root_bus() instead of pci_scan_root_bus()
  PCI: designware: Parse bus-range property from devicetree
  PCI: designware: Add support for v3.65 hardware

* pci/host-imx6:
  PCI: imx6: Probe in module_init(), not fs_initcall()
  PCI: designware: Remove pci_assign_unassigned_resources() from dw_pcie_host_init()
  PCI: designware: Use pci_create_root_bus() instead of pci_scan_root_bus()
  PCI: designware: Parse bus-range property from devicetree
  PCI: imx6: Put LTSSM in "Detect" state before disabling it
  MAINTAINERS: Add Lucas Stach as co-maintainer for i.MX6 PCI driver
  PCI: designware: Add support for v3.65 hardware

* pci/host-keystone:
  PCI: keystone: Add TI Keystone PCIe driver
  PCI: designware: Add support for v3.65 hardware

* pci/host-tegra:
  PCI: tegra: Implement a proper resource hierarchy
  PCI: tegra: Add missing cleanup in error path and tegra_msi_teardown_irq()
  resources: Add device-managed request/release_resource()

* pci/host-xilinx:
  PCI: xilinx: Add Xilinx AXI PCIe Host Bridge IP driver

Conflicts:
	drivers/pci/host/Kconfig
	drivers/pci/host/Makefile

Documentation/devicetree/bindings/pci/designware-pcie.txt

@@ -23,3 +23,6 @@ Required properties:
 
 Optional properties:
 - reset-gpio: gpio pin number of power good signal
+- bus-range: PCI bus numbers covered (it is recommended for new devicetrees to
+  specify this property, to keep backwards compatibility a range of 0x00-0xff
+  is assumed if not present)

Documentation/devicetree/bindings/pci/pci-keystone.txt

+TI Keystone PCIe interface
+
+Keystone PCI host Controller is based on Designware PCI h/w version 3.65.
+It shares common functions with PCIe Designware core driver and inherit
+common properties defined in
+Documentation/devicetree/bindings/pci/designware-pci.txt
+
+Please refer to Documentation/devicetree/bindings/pci/designware-pci.txt
+for the details of Designware DT bindings.  Additional properties are
+described here as well as properties that are not applicable.
+
+Required Properties:-
+
+compatibility: "ti,keystone-pcie"
+reg:	index 1 is the base address and length of DW application registers.
+	index 2 is the base address and length of PCI mode configuration
+	register.
+	index 3 is the base address and length of PCI device ID register.
+
+pcie_msi_intc : Interrupt controller device node for MSI IRQ chip
+	interrupt-cells: should be set to 1
+	interrupt-parent: Parent interrupt controller phandle
+	interrupts: GIC interrupt lines connected to PCI MSI interrupt lines
+
+ Example:
+	pcie_msi_intc: msi-interrupt-controller {
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 31 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 32 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 33 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 34 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 35 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 36 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 37 IRQ_TYPE_EDGE_RISING>;
+	};
+
+pcie_intc: Interrupt controller device node for Legacy IRQ chip
+	interrupt-cells: should be set to 1
+	interrupt-parent: Parent interrupt controller phandle
+	interrupts: GIC interrupt lines connected to PCI Legacy interrupt lines
+
+ Example:
+	pcie_intc: legacy-interrupt-controller {
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>,
+			<GIC_SPI 27 IRQ_TYPE_EDGE_RISING>,
+			<GIC_SPI 28 IRQ_TYPE_EDGE_RISING>,
+			<GIC_SPI 29 IRQ_TYPE_EDGE_RISING>;
+	};
+
+Optional properties:-
+	phys: phandle to Generic Keystone SerDes phy for PCI
+	phy-names: name of the Generic Keystine SerDes phy for PCI
+	  - If boot loader already does PCI link establishment, then phys and
+	    phy-names shouldn't be present.
+
+Designware DT Properties not applicable for Keystone PCI
+
+1. pcie_bus clock-names not used.  Instead, a phandle to phys is used.
+
+Note for PCI driver usage
+=========================
+Driver requires pci=pcie_bus_perf in the bootargs for proper functioning.

Documentation/devicetree/bindings/pci/xilinx-pcie.txt

+* Xilinx AXI PCIe Root Port Bridge DT description
+
+Required properties:
+- #address-cells: Address representation for root ports, set to <3>
+- #size-cells: Size representation for root ports, set to <2>
+- #interrupt-cells: specifies the number of cells needed to encode an
+	interrupt source. The value must be 1.
+- compatible: Should contain "xlnx,axi-pcie-host-1.00.a"
+- reg: Should contain AXI PCIe registers location and length
+- device_type: must be "pci"
+- interrupts: Should contain AXI PCIe interrupt
+- interrupt-map-mask,
+  interrupt-map: standard PCI properties to define the mapping of the
+	PCI interface to interrupt numbers.
+- ranges: ranges for the PCI memory regions (I/O space region is not
+	supported by hardware)
+	Please refer to the standard PCI bus binding document for a more
+	detailed explanation
+
+Optional properties:
+- bus-range: PCI bus numbers covered
+
+Interrupt controller child node
++++++++++++++++++++++++++++++++
+Required properties:
+- interrupt-controller: identifies the node as an interrupt controller
+- #address-cells: specifies the number of cells needed to encode an
+	address. The value must be 0.
+- #interrupt-cells: specifies the number of cells needed to encode an
+	interrupt source. The value must be 1.
+
+NOTE:
+The core provides a single interrupt for both INTx/MSI messages. So,
+created a interrupt controller node to support 'interrupt-map' DT
+functionality.  The driver will create an IRQ domain for this map, decode
+the four INTx interrupts in ISR and route them to this domain.
+
+
+Example:
+++++++++
+
+	pci_express: axi-pcie@50000000 {
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+		compatible = "xlnx,axi-pcie-host-1.00.a";
+		reg = < 0x50000000 0x10000000 >;
+		device_type = "pci";
+		interrupts = < 0 52 4 >;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc 1>,
+				<0 0 0 2 &pcie_intc 2>,
+				<0 0 0 3 &pcie_intc 3>,
+				<0 0 0 4 &pcie_intc 4>;
+		ranges = < 0x02000000 0 0x60000000 0x60000000 0 0x10000000 >;
+
+		pcie_intc: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		}
+	};

Documentation/driver-model/devres.txt

@@ -264,8 +264,10 @@ IIO
 IO region
   devm_release_mem_region()
   devm_release_region()
+  devm_release_resource()
   devm_request_mem_region()
   devm_request_region()
+  devm_request_resource()
 
 IOMAP
   devm_ioport_map()

MAINTAINERS

@@ -6870,12 +6870,19 @@ F:	arch/x86/kernel/quirks.c
 
 PCI DRIVER FOR IMX6
 M:	Richard Zhu <r65037@freescale.com>
-M:	Shawn Guo <shawn.guo@freescale.com>
+M:	Lucas Stach <l.stach@pengutronix.de>
 L:	linux-pci@vger.kernel.org
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	drivers/pci/host/*imx6*
 
+PCI DRIVER FOR TI KEYSTONE
+M:	Murali Karicheri <m-karicheri2@ti.com>
+L:	linux-pci@vger.kernel.org
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+F:	drivers/pci/host/*keystone*
+
 PCI DRIVER FOR MVEBU (Marvell Armada 370 and Armada XP SOC support)
 M:	Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 M:	Jason Cooper <jason@lakedaemon.net>

drivers/pci/host/Kconfig

@@ -63,4 +63,23 @@ config PCIE_SPEAR13XX
 	help
 	  Say Y here if you want PCIe support on SPEAr13XX SoCs.
 
+
+config PCI_KEYSTONE
+	bool "TI Keystone PCIe controller"
+	depends on ARCH_KEYSTONE
+	select PCIE_DW
+	select PCIEPORTBUS
+	help
+	  Say Y here if you want to enable PCI controller support on Keystone
+	  SoCs. The PCI controller on Keystone is based on Designware hardware
+	  and therefore the driver re-uses the Designware core functions to
+	  implement the driver.
+
+config PCIE_XILINX
+	bool "Xilinx AXI PCIe host bridge support"
+	depends on ARCH_ZYNQ
+	help
+	  Say 'Y' here if you want kernel to support the Xilinx AXI PCIe
+	  Host Bridge driver.
+
 endmenu

drivers/pci/host/Makefile

@@ -8,3 +8,5 @@ obj-$(CONFIG_PCI_RCAR_GEN2) += pci-rcar-gen2.o
 obj-$(CONFIG_PCI_RCAR_GEN2_PCIE) += pcie-rcar.o
 obj-$(CONFIG_PCI_HOST_GENERIC) += pci-host-generic.o
 obj-$(CONFIG_PCIE_SPEAR13XX) += pcie-spear13xx.o
+obj-$(CONFIG_PCI_KEYSTONE) += pci-keystone-dw.o pci-keystone.o
+obj-$(CONFIG_PCIE_XILINX) += pcie-xilinx.o

drivers/pci/host/pci-imx6.c

@@ -49,6 +49,9 @@ struct imx6_pcie {
 
 /* PCIe Port Logic registers (memory-mapped) */
 #define PL_OFFSET 0x700
+#define PCIE_PL_PFLR (PL_OFFSET + 0x08)
+#define PCIE_PL_PFLR_LINK_STATE_MASK		(0x3f << 16)
+#define PCIE_PL_PFLR_FORCE_LINK			(1 << 15)
 #define PCIE_PHY_DEBUG_R0 (PL_OFFSET + 0x28)
 #define PCIE_PHY_DEBUG_R1 (PL_OFFSET + 0x2c)
 #define PCIE_PHY_DEBUG_R1_XMLH_LINK_IN_TRAINING	(1 << 29)
@@ -214,6 +217,32 @@ static int imx6q_pcie_abort_handler(unsigned long addr,
 static int imx6_pcie_assert_core_reset(struct pcie_port *pp)
 {
 	struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
+	u32 val, gpr1, gpr12;
+
+	/*
+	 * If the bootloader already enabled the link we need some special
+	 * handling to get the core back into a state where it is safe to
+	 * touch it for configuration.  As there is no dedicated reset signal
+	 * wired up for MX6QDL, we need to manually force LTSSM into "detect"
+	 * state before completely disabling LTSSM, which is a prerequisite
+	 * for core configuration.
+	 *
+	 * If both LTSSM_ENABLE and REF_SSP_ENABLE are active we have a strong
+	 * indication that the bootloader activated the link.
+	 */
+	regmap_read(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1, &gpr1);
+	regmap_read(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, &gpr12);
+
+	if ((gpr1 & IMX6Q_GPR1_PCIE_REF_CLK_EN) &&
+	    (gpr12 & IMX6Q_GPR12_PCIE_CTL_2)) {
+		val = readl(pp->dbi_base + PCIE_PL_PFLR);
+		val &= ~PCIE_PL_PFLR_LINK_STATE_MASK;
+		val |= PCIE_PL_PFLR_FORCE_LINK;
+		writel(val, pp->dbi_base + PCIE_PL_PFLR);
+
+		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+				IMX6Q_GPR12_PCIE_CTL_2, 0 << 10);
+	}
 
 	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
 			IMX6Q_GPR1_PCIE_TEST_PD, 1 << 18);
@@ -589,6 +618,14 @@ static int __init imx6_pcie_probe(struct platform_device *pdev)
 	return 0;
 }
 
+static void imx6_pcie_shutdown(struct platform_device *pdev)
+{
+	struct imx6_pcie *imx6_pcie = platform_get_drvdata(pdev);
+
+	/* bring down link, so bootloader gets clean state in case of reboot */
+	imx6_pcie_assert_core_reset(&imx6_pcie->pp);
+}
+
 static const struct of_device_id imx6_pcie_of_match[] = {
 	{ .compatible = "fsl,imx6q-pcie", },
 	{},
@@ -601,6 +638,7 @@ static struct platform_driver imx6_pcie_driver = {
 		.owner	= THIS_MODULE,
 		.of_match_table = imx6_pcie_of_match,
 	},
+	.shutdown = imx6_pcie_shutdown,
 };
 
 /* Freescale PCIe driver does not allow module unload */
@@ -609,7 +647,7 @@ static int __init imx6_pcie_init(void)
 {
 	return platform_driver_probe(&imx6_pcie_driver, imx6_pcie_probe);
 }
-fs_initcall(imx6_pcie_init);
+module_init(imx6_pcie_init);
 
 MODULE_AUTHOR("Sean Cross <xobs@kosagi.com>");
 MODULE_DESCRIPTION("Freescale i.MX6 PCIe host controller driver");

drivers/pci/host/pci-keystone-dw.c

+/*
+ * Designware application register space functions for Keystone PCI controller
+ *
+ * Copyright (C) 2013-2014 Texas Instruments., Ltd.
+ *		http://www.ti.com
+ *
+ * Author: Murali Karicheri <m-karicheri2@ti.com>
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_pci.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+
+#include "pcie-designware.h"
+#include "pci-keystone.h"
+
+/* Application register defines */
+#define LTSSM_EN_VAL		        1
+#define LTSSM_STATE_MASK		0x1f
+#define LTSSM_STATE_L0			0x11
+#define DBI_CS2_EN_VAL			0x20
+#define OB_XLAT_EN_VAL		        2
+
+/* Application registers */
+#define CMD_STATUS			0x004
+#define CFG_SETUP			0x008
+#define OB_SIZE				0x030
+#define CFG_PCIM_WIN_SZ_IDX		3
+#define CFG_PCIM_WIN_CNT		32
+#define SPACE0_REMOTE_CFG_OFFSET	0x1000
+#define OB_OFFSET_INDEX(n)		(0x200 + (8 * n))
+#define OB_OFFSET_HI(n)			(0x204 + (8 * n))
+
+/* IRQ register defines */
+#define IRQ_EOI				0x050
+#define IRQ_STATUS			0x184
+#define IRQ_ENABLE_SET			0x188
+#define IRQ_ENABLE_CLR			0x18c
+
+#define MSI_IRQ				0x054
+#define MSI0_IRQ_STATUS			0x104
+#define MSI0_IRQ_ENABLE_SET		0x108
+#define MSI0_IRQ_ENABLE_CLR		0x10c
+#define IRQ_STATUS			0x184
+#define MSI_IRQ_OFFSET			4
+
+/* Config space registers */
+#define DEBUG0				0x728
+
+#define to_keystone_pcie(x)	container_of(x, struct keystone_pcie, pp)
+
+static inline struct pcie_port *sys_to_pcie(struct pci_sys_data *sys)
+{
+	return sys->private_data;
+}
+
+static inline void update_reg_offset_bit_pos(u32 offset, u32 *reg_offset,
+					     u32 *bit_pos)
+{
+	*reg_offset = offset % 8;
+	*bit_pos = offset >> 3;
+}
+
+u32 ks_dw_pcie_get_msi_data(struct pcie_port *pp)
+{
+	struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+
+	return ks_pcie->app.start + MSI_IRQ;
+}
+
+void ks_dw_pcie_handle_msi_irq(struct keystone_pcie *ks_pcie, int offset)
+{
+	struct pcie_port *pp = &ks_pcie->pp;
+	u32 pending, vector;
+	int src, virq;
+
+	pending = readl(ks_pcie->va_app_base + MSI0_IRQ_STATUS + (offset << 4));
+
+	/*
+	 * MSI0 status bit 0-3 shows vectors 0, 8, 16, 24, MSI1 status bit
+	 * shows 1, 9, 17, 25 and so forth
+	 */
+	for (src = 0; src < 4; src++) {
+		if (BIT(src) & pending) {
+			vector = offset + (src << 3);
+			virq = irq_linear_revmap(pp->irq_domain, vector);
+			dev_dbg(pp->dev, "irq: bit %d, vector %d, virq %d\n",
+				src, vector, virq);
+			generic_handle_irq(virq);
+		}
+	}
+}
+
+static void ks_dw_pcie_msi_irq_ack(struct irq_data *d)
+{
+	u32 offset, reg_offset, bit_pos;
+	struct keystone_pcie *ks_pcie;
+	unsigned int irq = d->irq;
+	struct msi_desc *msi;
+	struct pcie_port *pp;
+
+	msi = irq_get_msi_desc(irq);
+	pp = sys_to_pcie(msi->dev->bus->sysdata);
+	ks_pcie = to_keystone_pcie(pp);
+	offset = irq - irq_linear_revmap(pp->irq_domain, 0);
+	update_reg_offset_bit_pos(offset, &reg_offset, &bit_pos);
+
+	writel(BIT(bit_pos),
+	       ks_pcie->va_app_base + MSI0_IRQ_STATUS + (reg_offset << 4));
+	writel(reg_offset + MSI_IRQ_OFFSET, ks_pcie->va_app_base + IRQ_EOI);
+}
+
+void ks_dw_pcie_msi_set_irq(struct pcie_port *pp, int irq)
+{
+	u32 reg_offset, bit_pos;
+	struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+
+	update_reg_offset_bit_pos(irq, &reg_offset, &bit_pos);
+	writel(BIT(bit_pos),
+	       ks_pcie->va_app_base + MSI0_IRQ_ENABLE_SET + (reg_offset << 4));
+}
+
+void ks_dw_pcie_msi_clear_irq(struct pcie_port *pp, int irq)
+{
+	u32 reg_offset, bit_pos;
+	struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+
+	update_reg_offset_bit_pos(irq, &reg_offset, &bit_pos);
+	writel(BIT(bit_pos),
+	       ks_pcie->va_app_base + MSI0_IRQ_ENABLE_CLR + (reg_offset << 4));
+}
+
+static void ks_dw_pcie_msi_irq_mask(struct irq_data *d)
+{
+	struct keystone_pcie *ks_pcie;
+	unsigned int irq = d->irq;
+	struct msi_desc *msi;
+	struct pcie_port *pp;
+	u32 offset;
+
+	msi = irq_get_msi_desc(irq);
+	pp = sys_to_pcie(msi->dev->bus->sysdata);
+	ks_pcie = to_keystone_pcie(pp);
+	offset = irq - irq_linear_revmap(pp->irq_domain, 0);
+
+	/* Mask the end point if PVM implemented */
+	if (IS_ENABLED(CONFIG_PCI_MSI)) {
+		if (msi->msi_attrib.maskbit)
+			mask_msi_irq(d);
+	}
+
+	ks_dw_pcie_msi_clear_irq(pp, offset);
+}
+
+static void ks_dw_pcie_msi_irq_unmask(struct irq_data *d)
+{
+	struct keystone_pcie *ks_pcie;
+	unsigned int irq = d->irq;
+	struct msi_desc *msi;
+	struct pcie_port *pp;
+	u32 offset;
+
+	msi = irq_get_msi_desc(irq);
+	pp = sys_to_pcie(msi->dev->bus->sysdata);
+	ks_pcie = to_keystone_pcie(pp);
+	offset = irq - irq_linear_revmap(pp->irq_domain, 0);
+
+	/* Mask the end point if PVM implemented */
+	if (IS_ENABLED(CONFIG_PCI_MSI)) {
+		if (msi->msi_attrib.maskbit)
+			unmask_msi_irq(d);
+	}
+
+	ks_dw_pcie_msi_set_irq(pp, offset);
+}
+
+static struct irq_chip ks_dw_pcie_msi_irq_chip = {
+	.name = "Keystone-PCIe-MSI-IRQ",
+	.irq_ack = ks_dw_pcie_msi_irq_ack,
+	.irq_mask = ks_dw_pcie_msi_irq_mask,
+	.irq_unmask = ks_dw_pcie_msi_irq_unmask,
+};
+
+static int ks_dw_pcie_msi_map(struct irq_domain *domain, unsigned int irq,
+			      irq_hw_number_t hwirq)
+{
+	irq_set_chip_and_handler(irq, &ks_dw_pcie_msi_irq_chip,
+				 handle_level_irq);
+	irq_set_chip_data(irq, domain->host_data);
+	set_irq_flags(irq, IRQF_VALID);
+
+	return 0;
+}
+
+const struct irq_domain_ops ks_dw_pcie_msi_domain_ops = {
+	.map = ks_dw_pcie_msi_map,
+};
+
+int ks_dw_pcie_msi_host_init(struct pcie_port *pp, struct msi_chip *chip)
+{
+	struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+	int i;
+
+	pp->irq_domain = irq_domain_add_linear(ks_pcie->msi_intc_np,
+					MAX_MSI_IRQS,
+					&ks_dw_pcie_msi_domain_ops,
+					chip);
+	if (!pp->irq_domain) {
+		dev_err(pp->dev, "irq domain init failed\n");
+		return -ENXIO;
+	}
+
+	for (i = 0; i < MAX_MSI_IRQS; i++)
+		irq_create_mapping(pp->irq_domain, i);
+
+	return 0;
+}
+
+void ks_dw_pcie_enable_legacy_irqs(struct keystone_pcie *ks_pcie)
+{
+	int i;
+
+	for (i = 0; i < MAX_LEGACY_IRQS; i++)
+		writel(0x1, ks_pcie->va_app_base + IRQ_ENABLE_SET + (i << 4));
+}
+
+void ks_dw_pcie_handle_legacy_irq(struct keystone_pcie *ks_pcie, int offset)
+{
+	struct pcie_port *pp = &ks_pcie->pp;
+	u32 pending;
+	int virq;
+
+	pending = readl(ks_pcie->va_app_base + IRQ_STATUS + (offset << 4));
+
+	if (BIT(0) & pending) {
+		virq = irq_linear_revmap(ks_pcie->legacy_irq_domain, offset);
+		dev_dbg(pp->dev, ": irq: irq_offset %d, virq %d\n", offset,
+			virq);
+		generic_handle_irq(virq);
+	}
+
+	/* EOI the INTx interrupt */
+	writel(offset, ks_pcie->va_app_base + IRQ_EOI);
+}
+
+static void ks_dw_pcie_ack_legacy_irq(struct irq_data *d)
+{
+}
+
+static void ks_dw_pcie_mask_legacy_irq(struct irq_data *d)
+{
+}
+
+static void ks_dw_pcie_unmask_legacy_irq(struct irq_data *d)
+{
+}
+
+static struct irq_chip ks_dw_pcie_legacy_irq_chip = {
+	.name = "Keystone-PCI-Legacy-IRQ",
+	.irq_ack = ks_dw_pcie_ack_legacy_irq,
+	.irq_mask = ks_dw_pcie_mask_legacy_irq,
+	.irq_unmask = ks_dw_pcie_unmask_legacy_irq,
+};
+
+static int ks_dw_pcie_init_legacy_irq_map(struct irq_domain *d,
+				unsigned int irq, irq_hw_number_t hw_irq)
+{
+	irq_set_chip_and_handler(irq, &ks_dw_pcie_legacy_irq_chip,
+				 handle_level_irq);
+	irq_set_chip_data(irq, d->host_data);
+	set_irq_flags(irq, IRQF_VALID);
+
+	return 0;
+}
+
+static const struct irq_domain_ops ks_dw_pcie_legacy_irq_domain_ops = {
+	.map = ks_dw_pcie_init_legacy_irq_map,
+	.xlate = irq_domain_xlate_onetwocell,
+};
+
+/**
+ * ks_dw_pcie_set_dbi_mode() - Set DBI mode to access overlaid BAR mask
+ * registers
+ *
+ * Since modification of dbi_cs2 involves different clock domain, read the
+ * status back to ensure the transition is complete.
+ */
+static void ks_dw_pcie_set_dbi_mode(void __iomem *reg_virt)
+{
+	u32 val;
+
+	writel(DBI_CS2_EN_VAL | readl(reg_virt + CMD_STATUS),
+	       reg_virt + CMD_STATUS);
+
+	do {
+		val = readl(reg_virt + CMD_STATUS);
+	} while (!(val & DBI_CS2_EN_VAL));
+}
+
+/**
+ * ks_dw_pcie_clear_dbi_mode() - Disable DBI mode
+ *
+ * Since modification of dbi_cs2 involves different clock domain, read the
+ * status back to ensure the transition is complete.
+ */
+static void ks_dw_pcie_clear_dbi_mode(void __iomem *reg_virt)
+{
+	u32 val;
+
+	writel(~DBI_CS2_EN_VAL & readl(reg_virt + CMD_STATUS),
+		     reg_virt + CMD_STATUS);
+
+	do {
+		val = readl(reg_virt + CMD_STATUS);
+	} while (val & DBI_CS2_EN_VAL);
+}
+
+void ks_dw_pcie_setup_rc_app_regs(struct keystone_pcie *ks_pcie)
+{
+	struct pcie_port *pp = &ks_pcie->pp;
+	u32 start = pp->mem.start, end = pp->mem.end;
+	int i, tr_size;
+
+	/* Disable BARs for inbound access */
+	ks_dw_pcie_set_dbi_mode(ks_pcie->va_app_base);
+	writel(0, pp->dbi_base + PCI_BASE_ADDRESS_0);
+	writel(0, pp->dbi_base + PCI_BASE_ADDRESS_1);
+	ks_dw_pcie_clear_dbi_mode(ks_pcie->va_app_base);
+
+	/* Set outbound translation size per window division */
+	writel(CFG_PCIM_WIN_SZ_IDX & 0x7, ks_pcie->va_app_base + OB_SIZE);
+
+	tr_size = (1 << (CFG_PCIM_WIN_SZ_IDX & 0x7)) * SZ_1M;
+
+	/* Using Direct 1:1 mapping of RC <-> PCI memory space */
+	for (i = 0; (i < CFG_PCIM_WIN_CNT) && (start < end); i++) {
+		writel(start | 1, ks_pcie->va_app_base + OB_OFFSET_INDEX(i));
+		writel(0, ks_pcie->va_app_base + OB_OFFSET_HI(i));
+		start += tr_size;
+	}
+
+	/* Enable OB translation */
+	writel(OB_XLAT_EN_VAL | readl(ks_pcie->va_app_base + CMD_STATUS),
+	       ks_pcie->va_app_base + CMD_STATUS);
+}
+
+/**
+ * ks_pcie_cfg_setup() - Set up configuration space address for a device
+ *
+ * @ks_pcie: ptr to keystone_pcie structure
+ * @bus: Bus number the device is residing on
+ * @devfn: device, function number info
+ *
+ * Forms and returns the address of configuration space mapped in PCIESS
+ * address space 0.  Also configures CFG_SETUP for remote configuration space
+ * access.
+ *
+ * The address space has two regions to access configuration - local and remote.
+ * We access local region for bus 0 (as RC is attached on bus 0) and remote
+ * region for others with TYPE 1 access when bus > 1.  As for device on bus = 1,
+ * we will do TYPE 0 access as it will be on our secondary bus (logical).
+ * CFG_SETUP is needed only for remote configuration access.
+ */
+static void __iomem *ks_pcie_cfg_setup(struct keystone_pcie *ks_pcie, u8 bus,
+				       unsigned int devfn)
+{
+	u8 device = PCI_SLOT(devfn), function = PCI_FUNC(devfn);
+	struct pcie_port *pp = &ks_pcie->pp;
+	u32 regval;
+
+	if (bus == 0)
+		return pp->dbi_base;
+
+	regval = (bus << 16) | (device << 8) | function;
+
+	/*
+	 * Since Bus#1 will be a virtual bus, we need to have TYPE0
+	 * access only.
+	 * TYPE 1
+	 */
+	if (bus != 1)
+		regval |= BIT(24);
+
+	writel(regval, ks_pcie->va_app_base + CFG_SETUP);
+	return pp->va_cfg0_base;
+}
+
+int ks_dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus,
+			     unsigned int devfn, int where, int size, u32 *val)
+{
+	struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+	u8 bus_num = bus->number;
+	void __iomem *addr;
+
+	addr = ks_pcie_cfg_setup(ks_pcie, bus_num, devfn);
+
+	return dw_pcie_cfg_read(addr + (where & ~0x3), where, size, val);
+}
+
+int ks_dw_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus,
+			     unsigned int devfn, int where, int size, u32 val)
+{
+	struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+	u8 bus_num = bus->number;
+	void __iomem *addr;
+
+	addr = ks_pcie_cfg_setup(ks_pcie, bus_num, devfn);
+
+	return dw_pcie_cfg_write(addr + (where & ~0x3), where, size, val);
+}
+
+/**
+ * ks_dw_pcie_v3_65_scan_bus() - keystone scan_bus post initialization
+ *
+ * This sets BAR0 to enable inbound access for MSI_IRQ register
+ */
+void ks_dw_pcie_v3_65_scan_bus(struct pcie_port *pp)
+{
+	struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+
+	/* Configure and set up BAR0 */
+	ks_dw_pcie_set_dbi_mode(ks_pcie->va_app_base);
+
+	/* Enable BAR0 */
+	writel(1, pp->dbi_base + PCI_BASE_ADDRESS_0);
+	writel(SZ_4K - 1, pp->dbi_base + PCI_BASE_ADDRESS_0);
+
+	ks_dw_pcie_clear_dbi_mode(ks_pcie->va_app_base);
+
+	 /*
+	  * For BAR0, just setting bus address for inbound writes (MSI) should
+	  * be sufficient.  Use physical address to avoid any conflicts.
+	  */
+	writel(ks_pcie->app.start, pp->dbi_base + PCI_BASE_ADDRESS_0);
+}
+
+/**
+ * ks_dw_pcie_link_up() - Check if link up
+ */
+int ks_dw_pcie_link_up(struct pcie_port *pp)
+{
+	u32 val = readl(pp->dbi_base + DEBUG0);
+
+	return (val & LTSSM_STATE_MASK) == LTSSM_STATE_L0;
+}
+
+void ks_dw_pcie_initiate_link_train(struct keystone_pcie *ks_pcie)
+{
+	u32 val;
+
+	/* Disable Link training */
+	val = readl(ks_pcie->va_app_base + CMD_STATUS);
+	val &= ~LTSSM_EN_VAL;
+	writel(LTSSM_EN_VAL | val,  ks_pcie->va_app_base + CMD_STATUS);
+
+	/* Initiate Link Training */
+	val = readl(ks_pcie->va_app_base + CMD_STATUS);
+	writel(LTSSM_EN_VAL | val,  ks_pcie->va_app_base + CMD_STATUS);
+}
+
+/**
+ * ks_dw_pcie_host_init() - initialize host for v3_65 dw hardware
+ *
+ * Ioremap the register resources, initialize legacy irq domain
+ * and call dw_pcie_v3_65_host_init() API to initialize the Keystone
+ * PCI host controller.
+ */
+int __init ks_dw_pcie_host_init(struct keystone_pcie *ks_pcie,
+				struct device_node *msi_intc_np)
+{
+	struct pcie_port *pp = &ks_pcie->pp;
+	struct platform_device *pdev = to_platform_device(pp->dev);
+	struct resource *res;
+
+	/* Index 0 is the config reg. space address */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	pp->dbi_base = devm_ioremap_resource(pp->dev, res);
+	if (IS_ERR(pp->dbi_base))
+		return PTR_ERR(pp->dbi_base);
+
+	/*
+	 * We set these same and is used in pcie rd/wr_other_conf
+	 * functions
+	 */
+	pp->va_cfg0_base = pp->dbi_base + SPACE0_REMOTE_CFG_OFFSET;
+	pp->va_cfg1_base = pp->va_cfg0_base;
+
+	/* Index 1 is the application reg. space address */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	ks_pcie->app = *res;
+	ks_pcie->va_app_base = devm_ioremap_resource(pp->dev, res);
+	if (IS_ERR(ks_pcie->va_app_base))
+		return PTR_ERR(ks_pcie->va_app_base);
+
+	/* Create legacy IRQ domain */
+	ks_pcie->legacy_irq_domain =
+			irq_domain_add_linear(ks_pcie->legacy_intc_np,
+					MAX_LEGACY_IRQS,
+					&ks_dw_pcie_legacy_irq_domain_ops,
+					NULL);
+	if (!ks_pcie->legacy_irq_domain) {
+		dev_err(pp->dev, "Failed to add irq domain for legacy irqs\n");
+		return -EINVAL;
+	}
+
+	return dw_pcie_host_init(pp);
+}

drivers/pci/host/pci-keystone.c

+/*
+ * PCIe host controller driver for Texas Instruments Keystone SoCs
+ *
+ * Copyright (C) 2013-2014 Texas Instruments., Ltd.
+ *		http://www.ti.com
+ *
+ * Author: Murali Karicheri <m-karicheri2@ti.com>
+ * Implementation based on pci-exynos.c and pcie-designware.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/irqchip/chained_irq.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/irqdomain.h>
+#include <linux/module.h>
+#include <linux/msi.h>
+#include <linux/of_irq.h>
+#include <linux/of.h>
+#include <linux/of_pci.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+#include <linux/resource.h>
+#include <linux/signal.h>
+
+#include "pcie-designware.h"
+#include "pci-keystone.h"
+
+#define DRIVER_NAME	"keystone-pcie"
+
+/* driver specific constants */
+#define MAX_MSI_HOST_IRQS		8
+#define MAX_LEGACY_HOST_IRQS		4
+
+/* RC mode settings masks */
+#define PCIE_RC_MODE		BIT(2)
+#define PCIE_MODE_MASK		(BIT(1) | BIT(2))
+
+/* DEV_STAT_CTRL */
+#define PCIE_CAP_BASE		0x70
+
+#define to_keystone_pcie(x)	container_of(x, struct keystone_pcie, pp)
+
+static int ks_pcie_establish_link(struct keystone_pcie *ks_pcie)
+{
+	struct pcie_port *pp = &ks_pcie->pp;
+	int count = 200;
+
+	dw_pcie_setup_rc(pp);
+
+	if (dw_pcie_link_up(pp)) {
+		dev_err(pp->dev, "Link already up\n");
+		return 0;
+	}
+
+	ks_dw_pcie_initiate_link_train(ks_pcie);
+	/* check if the link is up or not */
+	while (!dw_pcie_link_up(pp)) {
+		usleep_range(100, 1000);
+		if (--count) {
+			ks_dw_pcie_initiate_link_train(ks_pcie);
+			continue;
+		}
+		dev_err(pp->dev, "phy link never came up\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static void ks_pcie_msi_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+	struct keystone_pcie *ks_pcie = irq_desc_get_handler_data(desc);
+	u32 offset = irq - ks_pcie->msi_host_irqs[0];
+	struct pcie_port *pp = &ks_pcie->pp;
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+
+	dev_dbg(pp->dev, "ks_pci_msi_irq_handler, irq %d\n", irq);
+
+	/*
+	 * The chained irq handler installation would have replaced normal
+	 * interrupt driver handler so we need to take care of mask/unmask and
+	 * ack operation.
+	 */
+	chained_irq_enter(chip, desc);
+	ks_dw_pcie_handle_msi_irq(ks_pcie, offset);
+	chained_irq_exit(chip, desc);
+}
+
+/**
+ * ks_pcie_legacy_irq_handler() - Handle legacy interrupt
+ * @irq: IRQ line for legacy interrupts
+ * @desc: Pointer to irq descriptor
+ *
+ * Traverse through pending legacy interrupts and invoke handler for each. Also
+ * takes care of interrupt controller level mask/ack operation.
+ */
+static void ks_pcie_legacy_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+	struct keystone_pcie *ks_pcie = irq_desc_get_handler_data(desc);
+	struct pcie_port *pp = &ks_pcie->pp;
+	u32 irq_offset = irq - ks_pcie->legacy_host_irqs[0];
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+
+	dev_dbg(pp->dev, ": Handling legacy irq %d\n", irq);
+
+	/*
+	 * The chained irq handler installation would have replaced normal
+	 * interrupt driver handler so we need to take care of mask/unmask and
+	 * ack operation.
+	 */
+	chained_irq_enter(chip, desc);
+	ks_dw_pcie_handle_legacy_irq(ks_pcie, irq_offset);
+	chained_irq_exit(chip, desc);
+}
+
+static int ks_pcie_get_irq_controller_info(struct keystone_pcie *ks_pcie,
+					   char *controller, int *num_irqs)
+{
+	int temp, max_host_irqs, legacy = 1, *host_irqs, ret = -EINVAL;
+	struct device *dev = ks_pcie->pp.dev;
+	struct device_node *np_pcie = dev->of_node, **np_temp;
+
+	if (!strcmp(controller, "msi-interrupt-controller"))
+		legacy = 0;
+
+	if (legacy) {
+		np_temp = &ks_pcie->legacy_intc_np;
+		max_host_irqs = MAX_LEGACY_HOST_IRQS;
+		host_irqs = &ks_pcie->legacy_host_irqs[0];
+	} else {
+		np_temp = &ks_pcie->msi_intc_np;
+		max_host_irqs = MAX_MSI_HOST_IRQS;
+		host_irqs =  &ks_pcie->msi_host_irqs[0];
+	}
+
+	/* interrupt controller is in a child node */
+	*np_temp = of_find_node_by_name(np_pcie, controller);
+	if (!(*np_temp)) {
+		dev_err(dev, "Node for %s is absent\n", controller);
+		goto out;
+	}
+	temp = of_irq_count(*np_temp);
+	if (!temp)
+		goto out;
+	if (temp > max_host_irqs)
+		dev_warn(dev, "Too many %s interrupts defined %u\n",
+			(legacy ? "legacy" : "MSI"), temp);
+
+	/*
+	 * support upto max_host_irqs. In dt from index 0 to 3 (legacy) or 0 to
+	 * 7 (MSI)
+	 */
+	for (temp = 0; temp < max_host_irqs; temp++) {
+		host_irqs[temp] = irq_of_parse_and_map(*np_temp, temp);
+		if (host_irqs[temp] < 0)
+			break;
+	}
+	if (temp) {
+		*num_irqs = temp;
+		ret = 0;
+	}
+out:
+	return ret;
+}
+
+static void ks_pcie_setup_interrupts(struct keystone_pcie *ks_pcie)
+{
+	int i;
+
+	/* Legacy IRQ */
+	for (i = 0; i < ks_pcie->num_legacy_host_irqs; i++) {
+		irq_set_handler_data(ks_pcie->legacy_host_irqs[i], ks_pcie);
+		irq_set_chained_handler(ks_pcie->legacy_host_irqs[i],
+					ks_pcie_legacy_irq_handler);
+	}
+	ks_dw_pcie_enable_legacy_irqs(ks_pcie);
+
+	/* MSI IRQ */
+	if (IS_ENABLED(CONFIG_PCI_MSI)) {
+		for (i = 0; i < ks_pcie->num_msi_host_irqs; i++) {
+			irq_set_chained_handler(ks_pcie->msi_host_irqs[i],
+						ks_pcie_msi_irq_handler);
+			irq_set_handler_data(ks_pcie->msi_host_irqs[i],
+					     ks_pcie);
+		}
+	}
+}
+
+/*
+ * When a PCI device does not exist during config cycles, keystone host gets a
+ * bus error instead of returning 0xffffffff. This handler always returns 0
+ * for this kind of faults.
+ */
+static int keystone_pcie_fault(unsigned long addr, unsigned int fsr,
+				struct pt_regs *regs)
+{
+	unsigned long instr = *(unsigned long *) instruction_pointer(regs);
+
+	if ((instr & 0x0e100090) == 0x00100090) {
+		int reg = (instr >> 12) & 15;
+
+		regs->uregs[reg] = -1;
+		regs->ARM_pc += 4;
+	}
+
+	return 0;
+}
+
+static void __init ks_pcie_host_init(struct pcie_port *pp)
+{
+	u32 vendor_device_id, val;
+	struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+
+	ks_pcie_establish_link(ks_pcie);
+	ks_dw_pcie_setup_rc_app_regs(ks_pcie);
+	ks_pcie_setup_interrupts(ks_pcie);
+	writew(PCI_IO_RANGE_TYPE_32 | (PCI_IO_RANGE_TYPE_32 << 8),
+			pp->dbi_base + PCI_IO_BASE);
+
+	/* update the Vendor ID */
+	vendor_device_id = readl(ks_pcie->va_reg_pciid);
+	writew((vendor_device_id >> 16), pp->dbi_base + PCI_DEVICE_ID);
+
+	/* update the DEV_STAT_CTRL to publish right mrrs */
+	val = readl(pp->dbi_base + PCIE_CAP_BASE + PCI_EXP_DEVCTL);
+	val &= ~PCI_EXP_DEVCTL_READRQ;
+	/* set the mrrs to 256 bytes */
+	val |= BIT(12);
+	writel(val, pp->dbi_base + PCIE_CAP_BASE + PCI_EXP_DEVCTL);
+
+	/*
+	 * PCIe access errors that result into OCP errors are caught by ARM as
+	 * "External aborts"
+	 */
+	hook_fault_code(17, keystone_pcie_fault, SIGBUS, 0,
+			"Asynchronous external abort");
+}
+
+static struct pcie_host_ops keystone_pcie_host_ops = {
+	.rd_other_conf = ks_dw_pcie_rd_other_conf,
+	.wr_other_conf = ks_dw_pcie_wr_other_conf,
+	.link_up = ks_dw_pcie_link_up,
+	.host_init = ks_pcie_host_init,
+	.msi_set_irq = ks_dw_pcie_msi_set_irq,
+	.msi_clear_irq = ks_dw_pcie_msi_clear_irq,
+	.get_msi_data = ks_dw_pcie_get_msi_data,
+	.msi_host_init = ks_dw_pcie_msi_host_init,
+	.scan_bus = ks_dw_pcie_v3_65_scan_bus,
+};
+
+static int __init ks_add_pcie_port(struct keystone_pcie *ks_pcie,
+			 struct platform_device *pdev)
+{
+	struct pcie_port *pp = &ks_pcie->pp;
+	int ret;
+
+	ret = ks_pcie_get_irq_controller_info(ks_pcie,
+					"legacy-interrupt-controller",
+					&ks_pcie->num_legacy_host_irqs);
+	if (ret)
+		return ret;
+
+	if (IS_ENABLED(CONFIG_PCI_MSI)) {
+		ret = ks_pcie_get_irq_controller_info(ks_pcie,
+						"msi-interrupt-controller",
+						&ks_pcie->num_msi_host_irqs);
+		if (ret)
+			return ret;
+	}
+
+	pp->root_bus_nr = -1;
+	pp->ops = &keystone_pcie_host_ops;
+	ret = ks_dw_pcie_host_init(ks_pcie, ks_pcie->msi_intc_np);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to initialize host\n");
+		return ret;
+	}
+
+	return ret;
+}
+
+static const struct of_device_id ks_pcie_of_match[] = {
+	{
+		.type = "pci",
+		.compatible = "ti,keystone-pcie",
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, ks_pcie_of_match);
+
+static int __exit ks_pcie_remove(struct platform_device *pdev)
+{
+	struct keystone_pcie *ks_pcie = platform_get_drvdata(pdev);
+
+	clk_disable_unprepare(ks_pcie->clk);
+
+	return 0;
+}
+
+static int __init ks_pcie_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct keystone_pcie *ks_pcie;
+	struct pcie_port *pp;
+	struct resource *res;
+	void __iomem *reg_p;
+	struct phy *phy;
+	int ret = 0;
+	u32 val;
+
+	ks_pcie = devm_kzalloc(&pdev->dev, sizeof(*ks_pcie),
+				GFP_KERNEL);
+	if (!ks_pcie) {
+		dev_err(dev, "no memory for keystone pcie\n");
+		return -ENOMEM;
+	}
+	pp = &ks_pcie->pp;
+
+	/* index 2 is the devcfg register for RC mode settings */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+	reg_p = devm_ioremap_resource(dev, res);
+	if (IS_ERR(reg_p))
+		return PTR_ERR(reg_p);
+
+	/* enable RC mode in devcfg */
+	val = readl(reg_p);
+	val &= ~PCIE_MODE_MASK;
+	val |= PCIE_RC_MODE;
+	writel(val, reg_p);
+
+	/* initialize SerDes Phy if present */
+	phy = devm_phy_get(dev, "pcie-phy");
+	if (!IS_ERR_OR_NULL(phy)) {
+		ret = phy_init(phy);
+		if (ret < 0)
+			return ret;
+	}
+
+	/* index 3 is to read PCI DEVICE_ID */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 3);
+	reg_p = devm_ioremap_resource(dev, res);
+	if (IS_ERR(reg_p))
+		return PTR_ERR(reg_p);
+	ks_pcie->va_reg_pciid = reg_p;
+
+	pp->dev = dev;
+	platform_set_drvdata(pdev, ks_pcie);
+	ks_pcie->clk = devm_clk_get(dev, "pcie");
+	if (IS_ERR(ks_pcie->clk)) {
+		dev_err(dev, "Failed to get pcie rc clock\n");
+		return PTR_ERR(ks_pcie->clk);
+	}
+	ret = clk_prepare_enable(ks_pcie->clk);
+	if (ret)
+		return ret;
+
+	ret = ks_add_pcie_port(ks_pcie, pdev);
+	if (ret < 0)
+		goto fail_clk;
+
+	return 0;
+fail_clk:
+	clk_disable_unprepare(ks_pcie->clk);
+
+	return ret;
+}
+
+static struct platform_driver ks_pcie_driver __refdata = {
+	.probe  = ks_pcie_probe,
+	.remove = __exit_p(ks_pcie_remove),
+	.driver = {
+		.name	= "keystone-pcie",
+		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(ks_pcie_of_match),
+	},
+};
+
+module_platform_driver(ks_pcie_driver);
+
+MODULE_AUTHOR("Murali Karicheri <m-karicheri2@ti.com>");
+MODULE_DESCRIPTION("Keystone PCIe host controller driver");
+MODULE_LICENSE("GPL v2");

drivers/pci/host/pci-keystone.h

+/*
+ * Keystone PCI Controller's common includes
+ *
+ * Copyright (C) 2013-2014 Texas Instruments., Ltd.
+ *		http://www.ti.com
+ *
+ * Author: Murali Karicheri <m-karicheri2@ti.com>
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#define MAX_LEGACY_IRQS			4
+#define MAX_MSI_HOST_IRQS		8
+#define MAX_LEGACY_HOST_IRQS		4
+
+struct keystone_pcie {
+	struct	clk		*clk;
+	struct	pcie_port	pp;
+	void __iomem		*va_reg_pciid;
+
+	int			num_legacy_host_irqs;
+	int			legacy_host_irqs[MAX_LEGACY_HOST_IRQS];
+	struct			device_node *legacy_intc_np;
+
+	int			num_msi_host_irqs;
+	int			msi_host_irqs[MAX_MSI_HOST_IRQS];
+	struct			device_node *msi_intc_np;
+	struct irq_domain	*legacy_irq_domain;
+
+	/* Application register space */
+	void __iomem		*va_app_base;
+	struct resource		app;
+};
+
+/* Keystone DW specific MSI controller APIs/definitions */
+void ks_dw_pcie_handle_msi_irq(struct keystone_pcie *ks_pcie, int offset);
+u32 ks_dw_pcie_get_msi_data(struct pcie_port *pp);
+
+/* Keystone specific PCI controller APIs */
+void ks_dw_pcie_enable_legacy_irqs(struct keystone_pcie *ks_pcie);
+void ks_dw_pcie_handle_legacy_irq(struct keystone_pcie *ks_pcie, int offset);
+int  ks_dw_pcie_host_init(struct keystone_pcie *ks_pcie,
+			struct device_node *msi_intc_np);
+int ks_dw_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus,
+		unsigned int devfn, int where, int size, u32 val);
+int ks_dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus,
+		unsigned int devfn, int where, int size, u32 *val);
+void ks_dw_pcie_setup_rc_app_regs(struct keystone_pcie *ks_pcie);
+int ks_dw_pcie_link_up(struct pcie_port *pp);
+void ks_dw_pcie_initiate_link_train(struct keystone_pcie *ks_pcie);
+void ks_dw_pcie_msi_set_irq(struct pcie_port *pp, int irq);
+void ks_dw_pcie_msi_clear_irq(struct pcie_port *pp, int irq);
+void ks_dw_pcie_v3_65_scan_bus(struct pcie_port *pp);
+int ks_dw_pcie_msi_host_init(struct pcie_port *pp,
+		struct msi_chip *chip);

drivers/pci/host/pci-tegra.c

@@ -253,6 +253,7 @@ struct tegra_pcie {
 	struct list_head buses;
 	struct resource *cs;
 
+	struct resource all;
 	struct resource io;
 	struct resource mem;
 	struct resource prefetch;
@@ -626,6 +627,15 @@ DECLARE_PCI_FIXUP_FINAL(PCI_ANY_ID, PCI_ANY_ID, tegra_pcie_relax_enable);
 static int tegra_pcie_setup(int nr, struct pci_sys_data *sys)
 {
 	struct tegra_pcie *pcie = sys_to_pcie(sys);
+	int err;
+
+	err = devm_request_resource(pcie->dev, &pcie->all, &pcie->mem);
+	if (err < 0)
+		return err;
+
+	err = devm_request_resource(pcie->dev, &pcie->all, &pcie->prefetch);
+	if (err)
+		return err;
 
 	pci_add_resource_offset(&sys->resources, &pcie->mem, sys->mem_offset);
 	pci_add_resource_offset(&sys->resources, &pcie->prefetch,
@@ -1170,8 +1180,10 @@ static int tegra_msi_setup_irq(struct msi_chip *chip, struct pci_dev *pdev,
 		return hwirq;
 
 	irq = irq_create_mapping(msi->domain, hwirq);
-	if (!irq)
+	if (!irq) {
+		tegra_msi_free(msi, hwirq);
 		return -EINVAL;
+	}
 
 	irq_set_msi_desc(irq, desc);
 
@@ -1189,8 +1201,10 @@ static void tegra_msi_teardown_irq(struct msi_chip *chip, unsigned int irq)
 {
 	struct tegra_msi *msi = to_tegra_msi(chip);
 	struct irq_data *d = irq_get_irq_data(irq);
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
 
-	tegra_msi_free(msi, d->hwirq);
+	irq_dispose_mapping(irq);
+	tegra_msi_free(msi, hwirq);
 }
 
 static struct irq_chip tegra_msi_irq_chip = {
@@ -1514,6 +1528,12 @@ static int tegra_pcie_parse_dt(struct tegra_pcie *pcie)
 	struct resource res;
 	int err;
 
+	memset(&pcie->all, 0, sizeof(pcie->all));
+	pcie->all.flags = IORESOURCE_MEM;
+	pcie->all.name = np->full_name;
+	pcie->all.start = ~0;
+	pcie->all.end = 0;
+
 	if (of_pci_range_parser_init(&parser, np)) {
 		dev_err(pcie->dev, "missing \"ranges\" property\n");
 		return -EINVAL;
@@ -1525,21 +1545,31 @@ static int tegra_pcie_parse_dt(struct tegra_pcie *pcie)
 		switch (res.flags & IORESOURCE_TYPE_BITS) {
 		case IORESOURCE_IO:
 			memcpy(&pcie->io, &res, sizeof(res));
-			pcie->io.name = "I/O";
+			pcie->io.name = np->full_name;
 			break;
 
 		case IORESOURCE_MEM:
 			if (res.flags & IORESOURCE_PREFETCH) {
 				memcpy(&pcie->prefetch, &res, sizeof(res));
-				pcie->prefetch.name = "PREFETCH";
+				pcie->prefetch.name = "prefetchable";
 			} else {
 				memcpy(&pcie->mem, &res, sizeof(res));
-				pcie->mem.name = "MEM";
+				pcie->mem.name = "non-prefetchable";
 			}
 			break;
 		}
+
+		if (res.start <= pcie->all.start)
+			pcie->all.start = res.start;
+
+		if (res.end >= pcie->all.end)
+			pcie->all.end = res.end;
 	}
 
+	err = devm_request_resource(pcie->dev, &iomem_resource, &pcie->all);
+	if (err < 0)
+		return err;
+
 	err = of_pci_parse_bus_range(np, &pcie->busn);
 	if (err < 0) {
 		dev_err(pcie->dev, "failed to parse ranges property: %d\n",

drivers/pci/host/pcie-designware.c

@@ -73,6 +73,8 @@ static unsigned long global_io_offset;
 
 static inline struct pcie_port *sys_to_pcie(struct pci_sys_data *sys)
 {
+	BUG_ON(!sys->private_data);
+
 	return sys->private_data;
 }
 
@@ -261,11 +263,6 @@ static int assign_irq(int no_irqs, struct msi_desc *desc, int *pos)
 	int irq, pos0, pos1, i;
 	struct pcie_port *pp = sys_to_pcie(desc->dev->bus->sysdata);
 
-	if (!pp) {
-		BUG();
-		return -EINVAL;
-	}
-
 	pos0 = find_first_zero_bit(pp->msi_irq_in_use,
 			MAX_MSI_IRQS);
 	if (pos0 % no_irqs) {
@@ -326,10 +323,6 @@ static void clear_irq(unsigned int irq)
 	/* get the port structure */
 	msi = irq_data_get_msi(data);
 	pp = sys_to_pcie(msi->dev->bus->sysdata);
-	if (!pp) {
-		BUG();
-		return;
-	}
 
 	/* undo what was done in assign_irq */
 	pos = data->hwirq;
@@ -350,11 +343,6 @@ static int dw_msi_setup_irq(struct msi_chip *chip, struct pci_dev *pdev,
 	struct msi_msg msg;
 	struct pcie_port *pp = sys_to_pcie(pdev->bus->sysdata);
 
-	if (!pp) {
-		BUG();
-		return -EINVAL;
-	}
-
 	pci_read_config_word(pdev, desc->msi_attrib.pos+PCI_MSI_FLAGS,
 				&msg_ctr);
 	msgvec = (msg_ctr&PCI_MSI_FLAGS_QSIZE) >> 4;
@@ -425,7 +413,7 @@ int __init dw_pcie_host_init(struct pcie_port *pp)
 	struct resource *cfg_res;
 	u32 val, na, ns;
 	const __be32 *addrp;
-	int i, index;
+	int i, index, ret;
 
 	/* Find the address cell size and the number of cells in order to get
 	 * the untranslated address.
@@ -500,6 +488,16 @@ int __init dw_pcie_host_init(struct pcie_port *pp)
 		}
 	}
 
+	ret = of_pci_parse_bus_range(np, &pp->busn);
+	if (ret < 0) {
+		pp->busn.name = np->name;
+		pp->busn.start = 0;
+		pp->busn.end = 0xff;
+		pp->busn.flags = IORESOURCE_BUS;
+		dev_dbg(pp->dev, "failed to parse bus-range property: %d, using default %pR\n",
+			ret, &pp->busn);
+	}
+
 	if (!pp->dbi_base) {
 		pp->dbi_base = devm_ioremap(pp->dev, pp->cfg.start,
 					resource_size(&pp->cfg));
@@ -511,18 +509,25 @@ int __init dw_pcie_host_init(struct pcie_port *pp)
 
 	pp->mem_base = pp->mem.start;
 
+	if (!pp->va_cfg0_base) {
+		pp->cfg0_base = pp->cfg.start;
 		pp->va_cfg0_base = devm_ioremap(pp->dev, pp->cfg0_base,
 						pp->config.cfg0_size);
 		if (!pp->va_cfg0_base) {
 			dev_err(pp->dev, "error with ioremap in function\n");
 			return -ENOMEM;
 		}
+	}
+
+	if (!pp->va_cfg1_base) {
+		pp->cfg1_base = pp->cfg.start + pp->config.cfg0_size;
 		pp->va_cfg1_base = devm_ioremap(pp->dev, pp->cfg1_base,
 						pp->config.cfg1_size);
 		if (!pp->va_cfg1_base) {
 			dev_err(pp->dev, "error with ioremap\n");
 			return -ENOMEM;
 		}
+	}
 
 	if (of_property_read_u32(np, "num-lanes", &pp->lanes)) {
 		dev_err(pp->dev, "Failed to parse the number of lanes\n");
@@ -530,6 +535,7 @@ int __init dw_pcie_host_init(struct pcie_port *pp)
 	}
 
 	if (IS_ENABLED(CONFIG_PCI_MSI)) {
+		if (!pp->ops->msi_host_init) {
 			pp->irq_domain = irq_domain_add_linear(pp->dev->of_node,
 						MAX_MSI_IRQS, &msi_domain_ops,
 						&dw_pcie_msi_chip);
@@ -540,6 +546,11 @@ int __init dw_pcie_host_init(struct pcie_port *pp)
 
 			for (i = 0; i < MAX_MSI_IRQS; i++)
 				irq_create_mapping(pp->irq_domain, i);
+		} else {
+			ret = pp->ops->msi_host_init(pp, &dw_pcie_msi_chip);
+			if (ret < 0)
+				return ret;
+		}
 	}
 
 	if (pp->ops->host_init)
@@ -558,7 +569,6 @@ int __init dw_pcie_host_init(struct pcie_port *pp)
 	dw_pci.private_data = (void **)&pp;
 
 	pci_common_init_dev(pp->dev, &dw_pci);
-	pci_assign_unassigned_resources();
 #ifdef CONFIG_PCI_DOMAINS
 	dw_pci.domain++;
 #endif
@@ -707,11 +717,6 @@ static int dw_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
 	struct pcie_port *pp = sys_to_pcie(bus->sysdata);
 	int ret;
 
-	if (!pp) {
-		BUG();
-		return -EINVAL;
-	}
-
 	if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0) {
 		*val = 0xffffffff;
 		return PCIBIOS_DEVICE_NOT_FOUND;
@@ -736,11 +741,6 @@ static int dw_pcie_wr_conf(struct pci_bus *bus, u32 devfn,
 	struct pcie_port *pp = sys_to_pcie(bus->sysdata);
 	int ret;
 
-	if (!pp) {
-		BUG();
-		return -EINVAL;
-	}
-
 	if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0)
 		return PCIBIOS_DEVICE_NOT_FOUND;
 
@@ -768,9 +768,6 @@ static int dw_pcie_setup(int nr, struct pci_sys_data *sys)
 
 	pp = sys_to_pcie(sys);
 
-	if (!pp)
-		return 0;
-
 	if (global_io_offset < SZ_1M && pp->config.io_size > 0) {
 		sys->io_offset = global_io_offset - pp->config.io_bus_addr;
 		pci_ioremap_io(global_io_offset, pp->io_base);
@@ -781,6 +778,7 @@ static int dw_pcie_setup(int nr, struct pci_sys_data *sys)
 
 	sys->mem_offset = pp->mem.start - pp->config.mem_bus_addr;
 	pci_add_resource_offset(&sys->resources, &pp->mem, sys->mem_offset);
+	pci_add_resource(&sys->resources, &pp->busn);
 
 	return 1;
 }
@@ -790,14 +788,16 @@ static struct pci_bus *dw_pcie_scan_bus(int nr, struct pci_sys_data *sys)
 	struct pci_bus *bus;
 	struct pcie_port *pp = sys_to_pcie(sys);
 
-	if (pp) {
 	pp->root_bus_nr = sys->busnr;
-		bus = pci_scan_root_bus(pp->dev, sys->busnr, &dw_pcie_ops,
-					sys, &sys->resources);
-	} else {
-		bus = NULL;
-		BUG();
-	}
+	bus = pci_create_root_bus(pp->dev, sys->busnr,
+				  &dw_pcie_ops, sys, &sys->resources);
+	if (!bus)
+		return NULL;
+
+	pci_scan_child_bus(bus);
+
+	if (bus && pp->ops->scan_bus)
+		pp->ops->scan_bus(pp);
 
 	return bus;
 }

drivers/pci/host/pcie-designware.h

@@ -48,6 +48,7 @@ struct pcie_port {
 	struct resource		cfg;
 	struct resource		io;
 	struct resource		mem;
+	struct resource		busn;
 	struct pcie_port_info	config;
 	int			irq;
 	u32			lanes;
@@ -74,6 +75,8 @@ struct pcie_host_ops {
 	void (*msi_set_irq)(struct pcie_port *pp, int irq);
 	void (*msi_clear_irq)(struct pcie_port *pp, int irq);
 	u32 (*get_msi_data)(struct pcie_port *pp);
+	void (*scan_bus)(struct pcie_port *pp);
+	int (*msi_host_init)(struct pcie_port *pp, struct msi_chip *chip);
 };
 
 int dw_pcie_cfg_read(void __iomem *addr, int where, int size, u32 *val);

drivers/pci/host/pcie-xilinx.c

+/*
+ * PCIe host controller driver for Xilinx AXI PCIe Bridge
+ *
+ * Copyright (c) 2012 - 2014 Xilinx, Inc.
+ *
+ * Based on the Tegra PCIe driver
+ *
+ * Bits taken from Synopsys Designware Host controller driver and
+ * ARM PCI Host generic driver.
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/msi.h>
+#include <linux/of_address.h>
+#include <linux/of_pci.h>
+#include <linux/of_platform.h>
+#include <linux/of_irq.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+
+/* Register definitions */
+#define XILINX_PCIE_REG_BIR		0x00000130
+#define XILINX_PCIE_REG_IDR		0x00000138
+#define XILINX_PCIE_REG_IMR		0x0000013c
+#define XILINX_PCIE_REG_PSCR		0x00000144
+#define XILINX_PCIE_REG_RPSC		0x00000148
+#define XILINX_PCIE_REG_MSIBASE1	0x0000014c
+#define XILINX_PCIE_REG_MSIBASE2	0x00000150
+#define XILINX_PCIE_REG_RPEFR		0x00000154
+#define XILINX_PCIE_REG_RPIFR1		0x00000158
+#define XILINX_PCIE_REG_RPIFR2		0x0000015c
+
+/* Interrupt registers definitions */
+#define XILINX_PCIE_INTR_LINK_DOWN	BIT(0)
+#define XILINX_PCIE_INTR_ECRC_ERR	BIT(1)
+#define XILINX_PCIE_INTR_STR_ERR	BIT(2)
+#define XILINX_PCIE_INTR_HOT_RESET	BIT(3)
+#define XILINX_PCIE_INTR_CFG_TIMEOUT	BIT(8)
+#define XILINX_PCIE_INTR_CORRECTABLE	BIT(9)
+#define XILINX_PCIE_INTR_NONFATAL	BIT(10)
+#define XILINX_PCIE_INTR_FATAL		BIT(11)
+#define XILINX_PCIE_INTR_INTX		BIT(16)
+#define XILINX_PCIE_INTR_MSI		BIT(17)
+#define XILINX_PCIE_INTR_SLV_UNSUPP	BIT(20)
+#define XILINX_PCIE_INTR_SLV_UNEXP	BIT(21)
+#define XILINX_PCIE_INTR_SLV_COMPL	BIT(22)
+#define XILINX_PCIE_INTR_SLV_ERRP	BIT(23)
+#define XILINX_PCIE_INTR_SLV_CMPABT	BIT(24)
+#define XILINX_PCIE_INTR_SLV_ILLBUR	BIT(25)
+#define XILINX_PCIE_INTR_MST_DECERR	BIT(26)
+#define XILINX_PCIE_INTR_MST_SLVERR	BIT(27)
+#define XILINX_PCIE_INTR_MST_ERRP	BIT(28)
+#define XILINX_PCIE_IMR_ALL_MASK	0x1FF30FED
+#define XILINX_PCIE_IDR_ALL_MASK	0xFFFFFFFF
+
+/* Root Port Error FIFO Read Register definitions */
+#define XILINX_PCIE_RPEFR_ERR_VALID	BIT(18)
+#define XILINX_PCIE_RPEFR_REQ_ID	GENMASK(15, 0)
+#define XILINX_PCIE_RPEFR_ALL_MASK	0xFFFFFFFF
+
+/* Root Port Interrupt FIFO Read Register 1 definitions */
+#define XILINX_PCIE_RPIFR1_INTR_VALID	BIT(31)
+#define XILINX_PCIE_RPIFR1_MSI_INTR	BIT(30)
+#define XILINX_PCIE_RPIFR1_INTR_MASK	GENMASK(28, 27)
+#define XILINX_PCIE_RPIFR1_ALL_MASK	0xFFFFFFFF
+#define XILINX_PCIE_RPIFR1_INTR_SHIFT	27
+
+/* Bridge Info Register definitions */
+#define XILINX_PCIE_BIR_ECAM_SZ_MASK	GENMASK(18, 16)
+#define XILINX_PCIE_BIR_ECAM_SZ_SHIFT	16
+
+/* Root Port Interrupt FIFO Read Register 2 definitions */
+#define XILINX_PCIE_RPIFR2_MSG_DATA	GENMASK(15, 0)
+
+/* Root Port Status/control Register definitions */
+#define XILINX_PCIE_REG_RPSC_BEN	BIT(0)
+
+/* Phy Status/Control Register definitions */
+#define XILINX_PCIE_REG_PSCR_LNKUP	BIT(11)
+
+/* ECAM definitions */
+#define ECAM_BUS_NUM_SHIFT		20
+#define ECAM_DEV_NUM_SHIFT		12
+
+/* Number of MSI IRQs */
+#define XILINX_NUM_MSI_IRQS		128
+
+/* Number of Memory Resources */
+#define XILINX_MAX_NUM_RESOURCES	3
+
+/**
+ * struct xilinx_pcie_port - PCIe port information
+ * @reg_base: IO Mapped Register Base
+ * @irq: Interrupt number
+ * @msi_pages: MSI pages
+ * @root_busno: Root Bus number
+ * @dev: Device pointer
+ * @irq_domain: IRQ domain pointer
+ * @bus_range: Bus range
+ * @resources: Bus Resources
+ */
+struct xilinx_pcie_port {
+	void __iomem *reg_base;
+	u32 irq;
+	unsigned long msi_pages;
+	u8 root_busno;
+	struct device *dev;
+	struct irq_domain *irq_domain;
+	struct resource bus_range;
+	struct list_head resources;
+};
+
+static DECLARE_BITMAP(msi_irq_in_use, XILINX_NUM_MSI_IRQS);
+
+static inline struct xilinx_pcie_port *sys_to_pcie(struct pci_sys_data *sys)
+{
+	return sys->private_data;
+}
+
+static inline u32 pcie_read(struct xilinx_pcie_port *port, u32 reg)
+{
+	return readl(port->reg_base + reg);
+}
+
+static inline void pcie_write(struct xilinx_pcie_port *port, u32 val, u32 reg)
+{
+	writel(val, port->reg_base + reg);
+}
+
+static inline bool xilinx_pcie_link_is_up(struct xilinx_pcie_port *port)
+{
+	return (pcie_read(port, XILINX_PCIE_REG_PSCR) &
+		XILINX_PCIE_REG_PSCR_LNKUP) ? 1 : 0;
+}
+
+/**
+ * xilinx_pcie_clear_err_interrupts - Clear Error Interrupts
+ * @port: PCIe port information
+ */
+static void xilinx_pcie_clear_err_interrupts(struct xilinx_pcie_port *port)
+{
+	u32 val = pcie_read(port, XILINX_PCIE_REG_RPEFR);
+
+	if (val & XILINX_PCIE_RPEFR_ERR_VALID) {
+		dev_dbg(port->dev, "Requester ID %d\n",
+			val & XILINX_PCIE_RPEFR_REQ_ID);
+		pcie_write(port, XILINX_PCIE_RPEFR_ALL_MASK,
+			   XILINX_PCIE_REG_RPEFR);
+	}
+}
+
+/**
+ * xilinx_pcie_valid_device - Check if a valid device is present on bus
+ * @bus: PCI Bus structure
+ * @devfn: device/function
+ *
+ * Return: 'true' on success and 'false' if invalid device is found
+ */
+static bool xilinx_pcie_valid_device(struct pci_bus *bus, unsigned int devfn)
+{
+	struct xilinx_pcie_port *port = sys_to_pcie(bus->sysdata);
+
+	/* Check if link is up when trying to access downstream ports */
+	if (bus->number != port->root_busno)
+		if (!xilinx_pcie_link_is_up(port))
+			return false;
+
+	/* Only one device down on each root port */
+	if (bus->number == port->root_busno && devfn > 0)
+		return false;
+
+	/*
+	 * Do not read more than one device on the bus directly attached
+	 * to RC.
+	 */
+	if (bus->primary == port->root_busno && devfn > 0)
+		return false;
+
+	return true;
+}
+
+/**
+ * xilinx_pcie_config_base - Get configuration base
+ * @bus: PCI Bus structure
+ * @devfn: Device/function
+ * @where: Offset from base
+ *
+ * Return: Base address of the configuration space needed to be
+ *	   accessed.
+ */
+static void __iomem *xilinx_pcie_config_base(struct pci_bus *bus,
+					     unsigned int devfn, int where)
+{
+	struct xilinx_pcie_port *port = sys_to_pcie(bus->sysdata);
+	int relbus;
+
+	relbus = (bus->number << ECAM_BUS_NUM_SHIFT) |
+		 (devfn << ECAM_DEV_NUM_SHIFT);
+
+	return port->reg_base + relbus + where;
+}
+
+/**
+ * xilinx_pcie_read_config - Read configuration space
+ * @bus: PCI Bus structure
+ * @devfn: Device/function
+ * @where: Offset from base
+ * @size: Byte/word/dword
+ * @val: Value to be read
+ *
+ * Return: PCIBIOS_SUCCESSFUL on success
+ *	   PCIBIOS_DEVICE_NOT_FOUND on failure
+ */
+static int xilinx_pcie_read_config(struct pci_bus *bus, unsigned int devfn,
+				   int where, int size, u32 *val)
+{
+	void __iomem *addr;
+
+	if (!xilinx_pcie_valid_device(bus, devfn)) {
+		*val = 0xFFFFFFFF;
+		return PCIBIOS_DEVICE_NOT_FOUND;
+	}
+
+	addr = xilinx_pcie_config_base(bus, devfn, where);
+
+	switch (size) {
+	case 1:
+		*val = readb(addr);
+		break;
+	case 2:
+		*val = readw(addr);
+		break;
+	default:
+		*val = readl(addr);
+		break;
+	}
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+/**
+ * xilinx_pcie_write_config - Write configuration space
+ * @bus: PCI Bus structure
+ * @devfn: Device/function
+ * @where: Offset from base
+ * @size: Byte/word/dword
+ * @val: Value to be written to device
+ *
+ * Return: PCIBIOS_SUCCESSFUL on success
+ *	   PCIBIOS_DEVICE_NOT_FOUND on failure
+ */
+static int xilinx_pcie_write_config(struct pci_bus *bus, unsigned int devfn,
+				    int where, int size, u32 val)
+{
+	void __iomem *addr;
+
+	if (!xilinx_pcie_valid_device(bus, devfn))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	addr = xilinx_pcie_config_base(bus, devfn, where);
+
+	switch (size) {
+	case 1:
+		writeb(val, addr);
+		break;
+	case 2:
+		writew(val, addr);
+		break;
+	default:
+		writel(val, addr);
+		break;
+	}
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+/* PCIe operations */
+static struct pci_ops xilinx_pcie_ops = {
+	.read  = xilinx_pcie_read_config,
+	.write = xilinx_pcie_write_config,
+};
+
+/* MSI functions */
+
+/**
+ * xilinx_pcie_destroy_msi - Free MSI number
+ * @irq: IRQ to be freed
+ */
+static void xilinx_pcie_destroy_msi(unsigned int irq)
+{
+	struct irq_desc *desc;
+	struct msi_desc *msi;
+	struct xilinx_pcie_port *port;
+
+	desc = irq_to_desc(irq);
+	msi = irq_desc_get_msi_desc(desc);
+	port = sys_to_pcie(msi->dev->bus->sysdata);
+
+	if (!test_bit(irq, msi_irq_in_use))
+		dev_err(port->dev, "Trying to free unused MSI#%d\n", irq);
+	else
+		clear_bit(irq, msi_irq_in_use);
+}
+
+/**
+ * xilinx_pcie_assign_msi - Allocate MSI number
+ * @port: PCIe port structure
+ *
+ * Return: A valid IRQ on success and error value on failure.
+ */
+static int xilinx_pcie_assign_msi(struct xilinx_pcie_port *port)
+{
+	int pos;
+
+	pos = find_first_zero_bit(msi_irq_in_use, XILINX_NUM_MSI_IRQS);
+	if (pos < XILINX_NUM_MSI_IRQS)
+		set_bit(pos, msi_irq_in_use);
+	else
+		return -ENOSPC;
+
+	return pos;
+}
+
+/**
+ * xilinx_msi_teardown_irq - Destroy the MSI
+ * @chip: MSI Chip descriptor
+ * @irq: MSI IRQ to destroy
+ */
+static void xilinx_msi_teardown_irq(struct msi_chip *chip, unsigned int irq)
+{
+	xilinx_pcie_destroy_msi(irq);
+}
+
+/**
+ * xilinx_pcie_msi_setup_irq - Setup MSI request
+ * @chip: MSI chip pointer
+ * @pdev: PCIe device pointer
+ * @desc: MSI descriptor pointer
+ *
+ * Return: '0' on success and error value on failure
+ */
+static int xilinx_pcie_msi_setup_irq(struct msi_chip *chip,
+				     struct pci_dev *pdev,
+				     struct msi_desc *desc)
+{
+	struct xilinx_pcie_port *port = sys_to_pcie(pdev->bus->sysdata);
+	unsigned int irq;
+	int hwirq;
+	struct msi_msg msg;
+	phys_addr_t msg_addr;
+
+	hwirq = xilinx_pcie_assign_msi(port);
+	if (irq < 0)
+		return irq;
+
+	irq = irq_create_mapping(port->irq_domain, hwirq);
+	if (!irq)
+		return -EINVAL;
+
+	irq_set_msi_desc(irq, desc);
+
+	msg_addr = virt_to_phys((void *)port->msi_pages);
+
+	msg.address_hi = 0;
+	msg.address_lo = msg_addr;
+	msg.data = irq;
+
+	write_msi_msg(irq, &msg);
+
+	return 0;
+}
+
+/* MSI Chip Descriptor */
+static struct msi_chip xilinx_pcie_msi_chip = {
+	.setup_irq = xilinx_pcie_msi_setup_irq,
+	.teardown_irq = xilinx_msi_teardown_irq,
+};
+
+/* HW Interrupt Chip Descriptor */
+static struct irq_chip xilinx_msi_irq_chip = {
+	.name = "Xilinx PCIe MSI",
+	.irq_enable = unmask_msi_irq,
+	.irq_disable = mask_msi_irq,
+	.irq_mask = mask_msi_irq,
+	.irq_unmask = unmask_msi_irq,
+};
+
+/**
+ * xilinx_pcie_msi_map - Set the handler for the MSI and mark IRQ as valid
+ * @domain: IRQ domain
+ * @irq: Virtual IRQ number
+ * @hwirq: HW interrupt number
+ *
+ * Return: Always returns 0.
+ */
+static int xilinx_pcie_msi_map(struct irq_domain *domain, unsigned int irq,
+			       irq_hw_number_t hwirq)
+{
+	irq_set_chip_and_handler(irq, &xilinx_msi_irq_chip, handle_simple_irq);
+	irq_set_chip_data(irq, domain->host_data);
+	set_irq_flags(irq, IRQF_VALID);
+
+	return 0;
+}
+
+/* IRQ Domain operations */
+static const struct irq_domain_ops msi_domain_ops = {
+	.map = xilinx_pcie_msi_map,
+};
+
+/**
+ * xilinx_pcie_enable_msi - Enable MSI support
+ * @port: PCIe port information
+ */
+static void xilinx_pcie_enable_msi(struct xilinx_pcie_port *port)
+{
+	phys_addr_t msg_addr;
+
+	port->msi_pages = __get_free_pages(GFP_KERNEL, 0);
+	msg_addr = virt_to_phys((void *)port->msi_pages);
+	pcie_write(port, 0x0, XILINX_PCIE_REG_MSIBASE1);
+	pcie_write(port, msg_addr, XILINX_PCIE_REG_MSIBASE2);
+}
+
+/**
+ * xilinx_pcie_add_bus - Add MSI chip info to PCIe bus
+ * @bus: PCIe bus
+ */
+static void xilinx_pcie_add_bus(struct pci_bus *bus)
+{
+	if (IS_ENABLED(CONFIG_PCI_MSI)) {
+		struct xilinx_pcie_port *port = sys_to_pcie(bus->sysdata);
+
+		xilinx_pcie_msi_chip.dev = port->dev;
+		bus->msi = &xilinx_pcie_msi_chip;
+	}
+}
+
+/* INTx Functions */
+
+/**
+ * xilinx_pcie_intx_map - Set the handler for the INTx and mark IRQ as valid
+ * @domain: IRQ domain
+ * @irq: Virtual IRQ number
+ * @hwirq: HW interrupt number
+ *
+ * Return: Always returns 0.
+ */
+static int xilinx_pcie_intx_map(struct irq_domain *domain, unsigned int irq,
+				irq_hw_number_t hwirq)
+{
+	irq_set_chip_and_handler(irq, &dummy_irq_chip, handle_simple_irq);
+	irq_set_chip_data(irq, domain->host_data);
+	set_irq_flags(irq, IRQF_VALID);
+
+	return 0;
+}
+
+/* INTx IRQ Domain operations */
+static const struct irq_domain_ops intx_domain_ops = {
+	.map = xilinx_pcie_intx_map,
+};
+
+/* PCIe HW Functions */
+
+/**
+ * xilinx_pcie_intr_handler - Interrupt Service Handler
+ * @irq: IRQ number
+ * @data: PCIe port information
+ *
+ * Return: IRQ_HANDLED on success and IRQ_NONE on failure
+ */
+static irqreturn_t xilinx_pcie_intr_handler(int irq, void *data)
+{
+	struct xilinx_pcie_port *port = (struct xilinx_pcie_port *)data;
+	u32 val, mask, status, msi_data;
+
+	/* Read interrupt decode and mask registers */
+	val = pcie_read(port, XILINX_PCIE_REG_IDR);
+	mask = pcie_read(port, XILINX_PCIE_REG_IMR);
+
+	status = val & mask;
+	if (!status)
+		return IRQ_NONE;
+
+	if (status & XILINX_PCIE_INTR_LINK_DOWN)
+		dev_warn(port->dev, "Link Down\n");
+
+	if (status & XILINX_PCIE_INTR_ECRC_ERR)
+		dev_warn(port->dev, "ECRC failed\n");
+
+	if (status & XILINX_PCIE_INTR_STR_ERR)
+		dev_warn(port->dev, "Streaming error\n");
+
+	if (status & XILINX_PCIE_INTR_HOT_RESET)
+		dev_info(port->dev, "Hot reset\n");
+
+	if (status & XILINX_PCIE_INTR_CFG_TIMEOUT)
+		dev_warn(port->dev, "ECAM access timeout\n");
+
+	if (status & XILINX_PCIE_INTR_CORRECTABLE) {
+		dev_warn(port->dev, "Correctable error message\n");
+		xilinx_pcie_clear_err_interrupts(port);
+	}
+
+	if (status & XILINX_PCIE_INTR_NONFATAL) {
+		dev_warn(port->dev, "Non fatal error message\n");
+		xilinx_pcie_clear_err_interrupts(port);
+	}
+
+	if (status & XILINX_PCIE_INTR_FATAL) {
+		dev_warn(port->dev, "Fatal error message\n");
+		xilinx_pcie_clear_err_interrupts(port);
+	}
+
+	if (status & XILINX_PCIE_INTR_INTX) {
+		/* INTx interrupt received */
+		val = pcie_read(port, XILINX_PCIE_REG_RPIFR1);
+
+		/* Check whether interrupt valid */
+		if (!(val & XILINX_PCIE_RPIFR1_INTR_VALID)) {
+			dev_warn(port->dev, "RP Intr FIFO1 read error\n");
+			return IRQ_HANDLED;
+		}
+
+		/* Clear interrupt FIFO register 1 */
+		pcie_write(port, XILINX_PCIE_RPIFR1_ALL_MASK,
+			   XILINX_PCIE_REG_RPIFR1);
+
+		/* Handle INTx Interrupt */
+		val = ((val & XILINX_PCIE_RPIFR1_INTR_MASK) >>
+			XILINX_PCIE_RPIFR1_INTR_SHIFT) + 1;
+		generic_handle_irq(irq_find_mapping(port->irq_domain, val));
+	}
+
+	if (status & XILINX_PCIE_INTR_MSI) {
+		/* MSI Interrupt */
+		val = pcie_read(port, XILINX_PCIE_REG_RPIFR1);
+
+		if (!(val & XILINX_PCIE_RPIFR1_INTR_VALID)) {
+			dev_warn(port->dev, "RP Intr FIFO1 read error\n");
+			return IRQ_HANDLED;
+		}
+
+		if (val & XILINX_PCIE_RPIFR1_MSI_INTR) {
+			msi_data = pcie_read(port, XILINX_PCIE_REG_RPIFR2) &
+				   XILINX_PCIE_RPIFR2_MSG_DATA;
+
+			/* Clear interrupt FIFO register 1 */
+			pcie_write(port, XILINX_PCIE_RPIFR1_ALL_MASK,
+				   XILINX_PCIE_REG_RPIFR1);
+
+			if (IS_ENABLED(CONFIG_PCI_MSI)) {
+				/* Handle MSI Interrupt */
+				generic_handle_irq(msi_data);
+			}
+		}
+	}
+
+	if (status & XILINX_PCIE_INTR_SLV_UNSUPP)
+		dev_warn(port->dev, "Slave unsupported request\n");
+
+	if (status & XILINX_PCIE_INTR_SLV_UNEXP)
+		dev_warn(port->dev, "Slave unexpected completion\n");
+
+	if (status & XILINX_PCIE_INTR_SLV_COMPL)
+		dev_warn(port->dev, "Slave completion timeout\n");
+
+	if (status & XILINX_PCIE_INTR_SLV_ERRP)
+		dev_warn(port->dev, "Slave Error Poison\n");
+
+	if (status & XILINX_PCIE_INTR_SLV_CMPABT)
+		dev_warn(port->dev, "Slave Completer Abort\n");
+
+	if (status & XILINX_PCIE_INTR_SLV_ILLBUR)
+		dev_warn(port->dev, "Slave Illegal Burst\n");
+
+	if (status & XILINX_PCIE_INTR_MST_DECERR)
+		dev_warn(port->dev, "Master decode error\n");
+
+	if (status & XILINX_PCIE_INTR_MST_SLVERR)
+		dev_warn(port->dev, "Master slave error\n");
+
+	if (status & XILINX_PCIE_INTR_MST_ERRP)
+		dev_warn(port->dev, "Master error poison\n");
+
+	/* Clear the Interrupt Decode register */
+	pcie_write(port, status, XILINX_PCIE_REG_IDR);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * xilinx_pcie_free_irq_domain - Free IRQ domain
+ * @port: PCIe port information
+ */
+static void xilinx_pcie_free_irq_domain(struct xilinx_pcie_port *port)
+{
+	int i;
+	u32 irq, num_irqs;
+
+	/* Free IRQ Domain */
+	if (IS_ENABLED(CONFIG_PCI_MSI)) {
+
+		free_pages(port->msi_pages, 0);
+
+		num_irqs = XILINX_NUM_MSI_IRQS;
+	} else {
+		/* INTx */
+		num_irqs = 4;
+	}
+
+	for (i = 0; i < num_irqs; i++) {
+		irq = irq_find_mapping(port->irq_domain, i);
+		if (irq > 0)
+			irq_dispose_mapping(irq);
+	}
+
+	irq_domain_remove(port->irq_domain);
+}
+
+/**
+ * xilinx_pcie_init_irq_domain - Initialize IRQ domain
+ * @port: PCIe port information
+ *
+ * Return: '0' on success and error value on failure
+ */
+static int xilinx_pcie_init_irq_domain(struct xilinx_pcie_port *port)
+{
+	struct device *dev = port->dev;
+	struct device_node *node = dev->of_node;
+	struct device_node *pcie_intc_node;
+
+	/* Setup INTx */
+	pcie_intc_node = of_get_next_child(node, NULL);
+	if (!pcie_intc_node) {
+		dev_err(dev, "No PCIe Intc node found\n");
+		return PTR_ERR(pcie_intc_node);
+	}
+
+	port->irq_domain = irq_domain_add_linear(pcie_intc_node, 4,
+						 &intx_domain_ops,
+						 port);
+	if (!port->irq_domain) {
+		dev_err(dev, "Failed to get a INTx IRQ domain\n");
+		return PTR_ERR(port->irq_domain);
+	}
+
+	/* Setup MSI */
+	if (IS_ENABLED(CONFIG_PCI_MSI)) {
+		port->irq_domain = irq_domain_add_linear(node,
+							 XILINX_NUM_MSI_IRQS,
+							 &msi_domain_ops,
+							 &xilinx_pcie_msi_chip);
+		if (!port->irq_domain) {
+			dev_err(dev, "Failed to get a MSI IRQ domain\n");
+			return PTR_ERR(port->irq_domain);
+		}
+
+		xilinx_pcie_enable_msi(port);
+	}
+
+	return 0;
+}
+
+/**
+ * xilinx_pcie_init_port - Initialize hardware
+ * @port: PCIe port information
+ */
+static void xilinx_pcie_init_port(struct xilinx_pcie_port *port)
+{
+	if (xilinx_pcie_link_is_up(port))
+		dev_info(port->dev, "PCIe Link is UP\n");
+	else
+		dev_info(port->dev, "PCIe Link is DOWN\n");
+
+	/* Disable all interrupts */
+	pcie_write(port, ~XILINX_PCIE_IDR_ALL_MASK,
+		   XILINX_PCIE_REG_IMR);
+
+	/* Clear pending interrupts */
+	pcie_write(port, pcie_read(port, XILINX_PCIE_REG_IDR) &
+			 XILINX_PCIE_IMR_ALL_MASK,
+		   XILINX_PCIE_REG_IDR);
+
+	/* Enable all interrupts */
+	pcie_write(port, XILINX_PCIE_IMR_ALL_MASK, XILINX_PCIE_REG_IMR);
+
+	/* Enable the Bridge enable bit */
+	pcie_write(port, pcie_read(port, XILINX_PCIE_REG_RPSC) |
+			 XILINX_PCIE_REG_RPSC_BEN,
+		   XILINX_PCIE_REG_RPSC);
+}
+
+/**
+ * xilinx_pcie_setup - Setup memory resources
+ * @nr: Bus number
+ * @sys: Per controller structure
+ *
+ * Return: '1' on success and error value on failure
+ */
+static int xilinx_pcie_setup(int nr, struct pci_sys_data *sys)
+{
+	struct xilinx_pcie_port *port = sys_to_pcie(sys);
+
+	list_splice_init(&port->resources, &sys->resources);
+
+	return 1;
+}
+
+/**
+ * xilinx_pcie_scan_bus - Scan PCIe bus for devices
+ * @nr: Bus number
+ * @sys: Per controller structure
+ *
+ * Return: Valid Bus pointer on success and NULL on failure
+ */
+static struct pci_bus *xilinx_pcie_scan_bus(int nr, struct pci_sys_data *sys)
+{
+	struct xilinx_pcie_port *port = sys_to_pcie(sys);
+	struct pci_bus *bus;
+
+	port->root_busno = sys->busnr;
+	bus = pci_scan_root_bus(port->dev, sys->busnr, &xilinx_pcie_ops,
+				sys, &sys->resources);
+
+	return bus;
+}
+
+/**
+ * xilinx_pcie_parse_and_add_res - Add resources by parsing ranges
+ * @port: PCIe port information
+ *
+ * Return: '0' on success and error value on failure
+ */
+static int xilinx_pcie_parse_and_add_res(struct xilinx_pcie_port *port)
+{
+	struct device *dev = port->dev;
+	struct device_node *node = dev->of_node;
+	struct resource *mem;
+	resource_size_t offset;
+	struct of_pci_range_parser parser;
+	struct of_pci_range range;
+	struct pci_host_bridge_window *win;
+	int err = 0, mem_resno = 0;
+
+	/* Get the ranges */
+	if (of_pci_range_parser_init(&parser, node)) {
+		dev_err(dev, "missing \"ranges\" property\n");
+		return -EINVAL;
+	}
+
+	/* Parse the ranges and add the resources found to the list */
+	for_each_of_pci_range(&parser, &range) {
+
+		if (mem_resno >= XILINX_MAX_NUM_RESOURCES) {
+			dev_err(dev, "Maximum memory resources exceeded\n");
+			return -EINVAL;
+		}
+
+		mem = devm_kmalloc(dev, sizeof(*mem), GFP_KERNEL);
+		if (!mem) {
+			err = -ENOMEM;
+			goto free_resources;
+		}
+
+		of_pci_range_to_resource(&range, node, mem);
+
+		switch (mem->flags & IORESOURCE_TYPE_BITS) {
+		case IORESOURCE_MEM:
+			offset = range.cpu_addr - range.pci_addr;
+			mem_resno++;
+			break;
+		default:
+			err = -EINVAL;
+			break;
+		}
+
+		if (err < 0) {
+			dev_warn(dev, "Invalid resource found %pR\n", mem);
+			continue;
+		}
+
+		err = request_resource(&iomem_resource, mem);
+		if (err)
+			goto free_resources;
+
+		pci_add_resource_offset(&port->resources, mem, offset);
+	}
+
+	/* Get the bus range */
+	if (of_pci_parse_bus_range(node, &port->bus_range)) {
+		u32 val = pcie_read(port, XILINX_PCIE_REG_BIR);
+		u8 last;
+
+		last = (val & XILINX_PCIE_BIR_ECAM_SZ_MASK) >>
+			XILINX_PCIE_BIR_ECAM_SZ_SHIFT;
+
+		port->bus_range = (struct resource) {
+			.name	= node->name,
+			.start	= 0,
+			.end	= last,
+			.flags	= IORESOURCE_BUS,
+		};
+	}
+
+	/* Register bus resource */
+	pci_add_resource(&port->resources, &port->bus_range);
+
+	return 0;
+
+free_resources:
+	release_child_resources(&iomem_resource);
+	list_for_each_entry(win, &port->resources, list)
+		devm_kfree(dev, win->res);
+	pci_free_resource_list(&port->resources);
+
+	return err;
+}
+
+/**
+ * xilinx_pcie_parse_dt - Parse Device tree
+ * @port: PCIe port information
+ *
+ * Return: '0' on success and error value on failure
+ */
+static int xilinx_pcie_parse_dt(struct xilinx_pcie_port *port)
+{
+	struct device *dev = port->dev;
+	struct device_node *node = dev->of_node;
+	struct resource regs;
+	const char *type;
+	int err;
+
+	type = of_get_property(node, "device_type", NULL);
+	if (!type || strcmp(type, "pci")) {
+		dev_err(dev, "invalid \"device_type\" %s\n", type);
+		return -EINVAL;
+	}
+
+	err = of_address_to_resource(node, 0, &regs);
+	if (err) {
+		dev_err(dev, "missing \"reg\" property\n");
+		return err;
+	}
+
+	port->reg_base = devm_ioremap_resource(dev, &regs);
+	if (IS_ERR(port->reg_base))
+		return PTR_ERR(port->reg_base);
+
+	port->irq = irq_of_parse_and_map(node, 0);
+	err = devm_request_irq(dev, port->irq, xilinx_pcie_intr_handler,
+			       IRQF_SHARED, "xilinx-pcie", port);
+	if (err) {
+		dev_err(dev, "unable to request irq %d\n", port->irq);
+		return err;
+	}
+
+	return 0;
+}
+
+/**
+ * xilinx_pcie_probe - Probe function
+ * @pdev: Platform device pointer
+ *
+ * Return: '0' on success and error value on failure
+ */
+static int xilinx_pcie_probe(struct platform_device *pdev)
+{
+	struct xilinx_pcie_port *port;
+	struct hw_pci hw;
+	struct device *dev = &pdev->dev;
+	int err;
+
+	if (!dev->of_node)
+		return -ENODEV;
+
+	port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
+
+	port->dev = dev;
+
+	err = xilinx_pcie_parse_dt(port);
+	if (err) {
+		dev_err(dev, "Parsing DT failed\n");
+		return err;
+	}
+
+	xilinx_pcie_init_port(port);
+
+	err = xilinx_pcie_init_irq_domain(port);
+	if (err) {
+		dev_err(dev, "Failed creating IRQ Domain\n");
+		return err;
+	}
+
+	/*
+	 * Parse PCI ranges, configuration bus range and
+	 * request their resources
+	 */
+	INIT_LIST_HEAD(&port->resources);
+	err = xilinx_pcie_parse_and_add_res(port);
+	if (err) {
+		dev_err(dev, "Failed adding resources\n");
+		return err;
+	}
+
+	platform_set_drvdata(pdev, port);
+
+	/* Register the device */
+	memset(&hw, 0, sizeof(hw));
+	hw = (struct hw_pci) {
+		.nr_controllers	= 1,
+		.private_data	= (void **)&port,
+		.setup		= xilinx_pcie_setup,
+		.map_irq	= of_irq_parse_and_map_pci,
+		.add_bus	= xilinx_pcie_add_bus,
+		.scan		= xilinx_pcie_scan_bus,
+		.ops		= &xilinx_pcie_ops,
+	};
+	pci_common_init_dev(dev, &hw);
+
+	return 0;
+}
+
+/**
+ * xilinx_pcie_remove - Remove function
+ * @pdev: Platform device pointer
+ *
+ * Return: '0' always
+ */
+static int xilinx_pcie_remove(struct platform_device *pdev)
+{
+	struct xilinx_pcie_port *port = platform_get_drvdata(pdev);
+
+	xilinx_pcie_free_irq_domain(port);
+
+	return 0;
+}
+
+static struct of_device_id xilinx_pcie_of_match[] = {
+	{ .compatible = "xlnx,axi-pcie-host-1.00.a", },
+	{}
+};
+
+static struct platform_driver xilinx_pcie_driver = {
+	.driver = {
+		.name = "xilinx-pcie",
+		.owner = THIS_MODULE,
+		.of_match_table = xilinx_pcie_of_match,
+		.suppress_bind_attrs = true,
+	},
+	.probe = xilinx_pcie_probe,
+	.remove = xilinx_pcie_remove,
+};
+module_platform_driver(xilinx_pcie_driver);
+
+MODULE_AUTHOR("Xilinx Inc");
+MODULE_DESCRIPTION("Xilinx AXI PCIe driver");
+MODULE_LICENSE("GPL v2");

drivers/pci/pci-driver.c

@@ -55,7 +55,6 @@ int pci_add_dynid(struct pci_driver *drv,
 		  unsigned long driver_data)
 {
 	struct pci_dynid *dynid;
-	int retval;
 
 	dynid = kzalloc(sizeof(*dynid), GFP_KERNEL);
 	if (!dynid)
@@ -73,9 +72,7 @@ int pci_add_dynid(struct pci_driver *drv,
 	list_add_tail(&dynid->node, &drv->dynids.list);
 	spin_unlock(&drv->dynids.lock);
 
-	retval = driver_attach(&drv->driver);
-
-	return retval;
+	return driver_attach(&drv->driver);
 }
 EXPORT_SYMBOL_GPL(pci_add_dynid);
 

drivers/pci/pci.c

@@ -1907,10 +1907,6 @@ int pci_prepare_to_sleep(struct pci_dev *dev)
 	if (target_state == PCI_POWER_ERROR)
 		return -EIO;
 
-	/* D3cold during system suspend/hibernate is not supported */
-	if (target_state > PCI_D3hot)
-		target_state = PCI_D3hot;
-
 	pci_enable_wake(dev, target_state, device_may_wakeup(&dev->dev));
 
 	error = pci_set_power_state(dev, target_state);

drivers/pci/pcie/portdrv_pci.c

@@ -93,77 +93,6 @@ static int pcie_port_resume_noirq(struct device *dev)
 	return 0;
 }
 
-#ifdef CONFIG_PM_RUNTIME
-struct d3cold_info {
-	bool no_d3cold;
-	unsigned int d3cold_delay;
-};
-
-static int pci_dev_d3cold_info(struct pci_dev *pdev, void *data)
-{
-	struct d3cold_info *info = data;
-
-	info->d3cold_delay = max_t(unsigned int, pdev->d3cold_delay,
-				   info->d3cold_delay);
-	if (pdev->no_d3cold)
-		info->no_d3cold = true;
-	return 0;
-}
-
-static int pcie_port_runtime_suspend(struct device *dev)
-{
-	struct pci_dev *pdev = to_pci_dev(dev);
-	struct d3cold_info d3cold_info = {
-		.no_d3cold	= false,
-		.d3cold_delay	= PCI_PM_D3_WAIT,
-	};
-
-	/*
-	 * If any subordinate device disable D3cold, we should not put
-	 * the port into D3cold.  The D3cold delay of port should be
-	 * the max of that of all subordinate devices.
-	 */
-	pci_walk_bus(pdev->subordinate, pci_dev_d3cold_info, &d3cold_info);
-	pdev->no_d3cold = d3cold_info.no_d3cold;
-	pdev->d3cold_delay = d3cold_info.d3cold_delay;
-	return 0;
-}
-
-static int pcie_port_runtime_resume(struct device *dev)
-{
-	return 0;
-}
-
-static int pci_dev_pme_poll(struct pci_dev *pdev, void *data)
-{
-	bool *pme_poll = data;
-
-	if (pdev->pme_poll)
-		*pme_poll = true;
-	return 0;
-}
-
-static int pcie_port_runtime_idle(struct device *dev)
-{
-	struct pci_dev *pdev = to_pci_dev(dev);
-	bool pme_poll = false;
-
-	/*
-	 * If any subordinate device needs pme poll, we should keep
-	 * the port in D0, because we need port in D0 to poll it.
-	 */
-	pci_walk_bus(pdev->subordinate, pci_dev_pme_poll, &pme_poll);
-	/* Delay for a short while to prevent too frequent suspend/resume */
-	if (!pme_poll)
-		pm_schedule_suspend(dev, 10);
-	return -EBUSY;
-}
-#else
-#define pcie_port_runtime_suspend	NULL
-#define pcie_port_runtime_resume	NULL
-#define pcie_port_runtime_idle		NULL
-#endif
-
 static const struct dev_pm_ops pcie_portdrv_pm_ops = {
 	.suspend	= pcie_port_device_suspend,
 	.resume		= pcie_port_device_resume,
@@ -172,9 +101,6 @@ static const struct dev_pm_ops pcie_portdrv_pm_ops = {
 	.poweroff	= pcie_port_device_suspend,
 	.restore	= pcie_port_device_resume,
 	.resume_noirq	= pcie_port_resume_noirq,
-	.runtime_suspend = pcie_port_runtime_suspend,
-	.runtime_resume = pcie_port_runtime_resume,
-	.runtime_idle	= pcie_port_runtime_idle,
 };
 
 #define PCIE_PORTDRV_PM_OPS	(&pcie_portdrv_pm_ops)

include/linux/aer.h

@@ -7,6 +7,8 @@
 #ifndef _AER_H_
 #define _AER_H_
 
+#include <linux/types.h>
+
 #define AER_NONFATAL			0
 #define AER_FATAL			1
 #define AER_CORRECTABLE			2

include/linux/ioport.h

@@ -215,6 +215,11 @@ static inline int __deprecated check_region(resource_size_t s,
 
 /* Wrappers for managed devices */
 struct device;
+
+extern int devm_request_resource(struct device *dev, struct resource *root,
+				 struct resource *new);
+extern void devm_release_resource(struct device *dev, struct resource *new);
+
 #define devm_request_region(dev,start,n,name) \
 	__devm_request_region(dev, &ioport_resource, (start), (n), (name))
 #define devm_request_mem_region(dev,start,n,name) \

kernel/resource.c

@@ -1248,6 +1248,76 @@ int release_mem_region_adjustable(struct resource *parent,
 /*
  * Managed region resource
  */
+static void devm_resource_release(struct device *dev, void *ptr)
+{
+	struct resource **r = ptr;
+
+	release_resource(*r);
+}
+
+/**
+ * devm_request_resource() - request and reserve an I/O or memory resource
+ * @dev: device for which to request the resource
+ * @root: root of the resource tree from which to request the resource
+ * @new: descriptor of the resource to request
+ *
+ * This is a device-managed version of request_resource(). There is usually
+ * no need to release resources requested by this function explicitly since
+ * that will be taken care of when the device is unbound from its driver.
+ * If for some reason the resource needs to be released explicitly, because
+ * of ordering issues for example, drivers must call devm_release_resource()
+ * rather than the regular release_resource().
+ *
+ * When a conflict is detected between any existing resources and the newly
+ * requested resource, an error message will be printed.
+ *
+ * Returns 0 on success or a negative error code on failure.
+ */
+int devm_request_resource(struct device *dev, struct resource *root,
+			  struct resource *new)
+{
+	struct resource *conflict, **ptr;
+
+	ptr = devres_alloc(devm_resource_release, sizeof(*ptr), GFP_KERNEL);
+	if (!ptr)
+		return -ENOMEM;
+
+	*ptr = new;
+
+	conflict = request_resource_conflict(root, new);
+	if (conflict) {
+		dev_err(dev, "resource collision: %pR conflicts with %s %pR\n",
+			new, conflict->name, conflict);
+		devres_free(ptr);
+		return -EBUSY;
+	}
+
+	devres_add(dev, ptr);
+	return 0;
+}
+EXPORT_SYMBOL(devm_request_resource);
+
+static int devm_resource_match(struct device *dev, void *res, void *data)
+{
+	struct resource **ptr = res;
+
+	return *ptr == data;
+}
+
+/**
+ * devm_release_resource() - release a previously requested resource
+ * @dev: device for which to release the resource
+ * @new: descriptor of the resource to release
+ *
+ * Releases a resource previously requested using devm_request_resource().
+ */
+void devm_release_resource(struct device *dev, struct resource *new)
+{
+	WARN_ON(devres_release(dev, devm_resource_release, devm_resource_match,
+			       new));
+}
+EXPORT_SYMBOL(devm_release_resource);
+
 struct region_devres {
 	struct resource *parent;
 	resource_size_t start;