提交 a0d3e665 编写于 作者: M Michal Simek

microblaze: ftrace: add function graph support

For more information look at Documentation/trace folder.
Signed-off-by: NMichal Simek <monstr@monstr.eu>
上级 7d241ff0
...@@ -8,6 +8,7 @@ config MICROBLAZE ...@@ -8,6 +8,7 @@ config MICROBLAZE
select HAVE_LMB select HAVE_LMB
select HAVE_FUNCTION_TRACER select HAVE_FUNCTION_TRACER
select HAVE_FUNCTION_TRACE_MCOUNT_TEST select HAVE_FUNCTION_TRACE_MCOUNT_TEST
select HAVE_FUNCTION_GRAPH_TRACER
select HAVE_DYNAMIC_FTRACE select HAVE_DYNAMIC_FTRACE
select HAVE_FTRACE_MCOUNT_RECORD select HAVE_FTRACE_MCOUNT_RECORD
select USB_ARCH_HAS_EHCI select USB_ARCH_HAS_EHCI
......
...@@ -14,6 +14,64 @@ ...@@ -14,6 +14,64 @@
#include <asm/cacheflush.h> #include <asm/cacheflush.h>
#include <linux/ftrace.h> #include <linux/ftrace.h>
#ifdef CONFIG_FUNCTION_GRAPH_TRACER
/*
* Hook the return address and push it in the stack of return addrs
* in current thread info.
*/
void prepare_ftrace_return(unsigned long *parent, unsigned long self_addr)
{
unsigned long old;
int faulted, err;
struct ftrace_graph_ent trace;
unsigned long return_hooker = (unsigned long)
&return_to_handler;
if (unlikely(atomic_read(&current->tracing_graph_pause)))
return;
/*
* Protect against fault, even if it shouldn't
* happen. This tool is too much intrusive to
* ignore such a protection.
*/
asm volatile(" 1: lwi %0, %2, 0; \
2: swi %3, %2, 0; \
addik %1, r0, 0; \
3: \
.section .fixup, \"ax\"; \
4: brid 3b; \
addik %1, r0, 1; \
.previous; \
.section __ex_table,\"a\"; \
.word 1b,4b; \
.word 2b,4b; \
.previous;" \
: "=&r" (old), "=r" (faulted)
: "r" (parent), "r" (return_hooker)
);
if (unlikely(faulted)) {
ftrace_graph_stop();
WARN_ON(1);
return;
}
err = ftrace_push_return_trace(old, self_addr, &trace.depth, 0);
if (err == -EBUSY) {
*parent = old;
return;
}
trace.func = self_addr;
/* Only trace if the calling function expects to */
if (!ftrace_graph_entry(&trace)) {
current->curr_ret_stack--;
*parent = old;
}
}
#endif /* CONFIG_FUNCTION_GRAPH_TRACER */
#ifdef CONFIG_DYNAMIC_FTRACE #ifdef CONFIG_DYNAMIC_FTRACE
/* save value to addr - it is save to do it in asm */ /* save value to addr - it is save to do it in asm */
static int ftrace_modify_code(unsigned long addr, unsigned int value) static int ftrace_modify_code(unsigned long addr, unsigned int value)
......
...@@ -96,6 +96,27 @@ ENTRY(ftrace_caller) ...@@ -96,6 +96,27 @@ ENTRY(ftrace_caller)
bneid r5, end; bneid r5, end;
nop; nop;
/* MS: HAVE_FUNCTION_TRACE_MCOUNT_TEST end of checking */ /* MS: HAVE_FUNCTION_TRACE_MCOUNT_TEST end of checking */
#ifdef CONFIG_FUNCTION_GRAPH_TRACER
lwi r5, r0, ftrace_graph_return;
addik r6, r0, ftrace_stub; /* asm implementation */
cmpu r5, r5, r6; /* ftrace_graph_return != ftrace_stub */
beqid r5, end_graph_tracer;
nop;
lwi r6, r0, ftrace_graph_entry;
addik r5, r0, ftrace_graph_entry_stub; /* implemented in C */
cmpu r5, r5, r6; /* ftrace_graph_entry != ftrace_graph_entry_stub */
beqid r5, end_graph_tracer;
nop;
addik r5, r1, 120; /* MS: load parent addr */
addik r6, r15, 0; /* MS: load current function addr */
bralid r15, prepare_ftrace_return;
nop;
/* MS: graph was taken that's why - can jump over function trace */
brid end;
nop;
end_graph_tracer:
#endif /* CONFIG_FUNCTION_GRAPH_TRACER */
#ifndef CONFIG_DYNAMIC_FTRACE #ifndef CONFIG_DYNAMIC_FTRACE
/* MS: test function trace if is taken or not */ /* MS: test function trace if is taken or not */
lwi r20, r0, ftrace_trace_function; lwi r20, r0, ftrace_trace_function;
...@@ -121,3 +142,23 @@ end: ...@@ -121,3 +142,23 @@ end:
rtsd r15, 8; /* MS: jump back */ rtsd r15, 8; /* MS: jump back */
nop; nop;
#ifdef CONFIG_FUNCTION_GRAPH_TRACER
ENTRY(return_to_handler)
nop; /* MS: just barrier for rtsd r15, 8 */
nop;
SAVE_REGS
swi r15, r1, 0;
/* MS: find out returning address */
bralid r15, ftrace_return_to_handler;
nop;
/* MS: return value from ftrace_return_to_handler is my returning addr
* must be before restore regs because I have to restore r3 content */
addik r15, r3, 0;
RESTORE_REGS
rtsd r15, 8; /* MS: jump back */
nop;
#endif /* CONFIG_FUNCTION_TRACER */
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册