ARM: dts: Add initial support for Arndale Octa board

Arndale Octa board is based on Exynos5420 SoC. This patch
adds the basic support required for booting it through DT.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

arch/arm/boot/dts/Makefile

@@ -63,6 +63,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos5250-arndale.dtb \
 	exynos5250-smdk5250.dtb \
 	exynos5250-snow.dtb \
+	exynos5420-arndale-octa.dtb \
 	exynos5420-smdk5420.dtb \
 	exynos5440-sd5v1.dtb \
 	exynos5440-ssdk5440.dtb

arch/arm/boot/dts/exynos5420-arndale-octa.dts

+/*
+ * Samsung's Exynos5420 based Arndale Octa board device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+#include "exynos5420.dtsi"
+
+/ {
+	model = "Insignal Arndale Octa evaluation board based on EXYNOS5420";
+	compatible = "insignal,arndale-octa", "samsung,exynos5420";
+
+	memory {
+		reg = <0x20000000 0x80000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttySAC3,115200";
+	};
+
+	fixed-rate-clocks {
+		oscclk {
+			compatible = "samsung,exynos5420-oscclk";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	mmc@12200000 {
+		status = "okay";
+		broken-cd;
+		supports-highspeed;
+		card-detect-delay = <200>;
+		samsung,dw-mshc-ciu-div = <3>;
+		samsung,dw-mshc-sdr-timing = <0 4>;
+		samsung,dw-mshc-ddr-timing = <0 2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
+
+		slot@0 {
+			reg = <0>;
+			bus-width = <8>;
+		};
+	};
+
+	mmc@12220000 {
+		status = "okay";
+		supports-highspeed;
+		card-detect-delay = <200>;
+		samsung,dw-mshc-ciu-div = <3>;
+		samsung,dw-mshc-sdr-timing = <2 3>;
+		samsung,dw-mshc-ddr-timing = <1 2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+
+		slot@0 {
+			reg = <0>;
+			bus-width = <4>;
+		};
+	};
+};