提交 9a6b0c73 编写于 作者: G Greg Ungerer

m68knommu: remove use of MBAR value for ColdFire 527x peripheral addressing

The ColdFire 527x family of CPUs does not have an MBAR register, so don't
define its peripheral addresses relative to one. Its internal peripherals
are relative to the IPSBAR register, so make sure to use that.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
上级 b62384af
......@@ -63,9 +63,17 @@
/*
* UART module.
*/
#define MCFUART_BASE1 0x200 /* Base address of UART1 */
#define MCFUART_BASE2 0x240 /* Base address of UART2 */
#define MCFUART_BASE3 0x280 /* Base address of UART3 */
#define MCFUART_BASE1 (MCF_IPSBAR + 0x200)
#define MCFUART_BASE2 (MCF_IPSBAR + 0x240)
#define MCFUART_BASE3 (MCF_IPSBAR + 0x280)
/*
* FEC ethernet module.
*/
#define MCFFEC_BASE0 (MCF_IPSBAR + 0x1000)
#define MCFFEC_SIZE0 0x800
#define MCFFEC_BASE1 (MCF_IPSBAR + 0x1800)
#define MCFFEC_SIZE1 0x800
#ifdef CONFIG_M5271
#define MCFGPIO_PODR_ADDR (MCF_IPSBAR + 0x100000)
......
......@@ -28,15 +28,15 @@
static struct mcf_platform_uart m527x_uart_platform[] = {
{
.mapbase = MCF_MBAR + MCFUART_BASE1,
.mapbase = MCFUART_BASE1,
.irq = MCFINT_VECBASE + MCFINT_UART0,
},
{
.mapbase = MCF_MBAR + MCFUART_BASE2,
.mapbase = MCFUART_BASE2,
.irq = MCFINT_VECBASE + MCFINT_UART1,
},
{
.mapbase = MCF_MBAR + MCFUART_BASE3,
.mapbase = MCFUART_BASE3,
.irq = MCFINT_VECBASE + MCFINT_UART2,
},
{ },
......@@ -50,8 +50,8 @@ static struct platform_device m527x_uart = {
static struct resource m527x_fec0_resources[] = {
{
.start = MCF_MBAR + 0x1000,
.end = MCF_MBAR + 0x1000 + 0x7ff,
.start = MCFFEC_BASE0,
.end = MCFFEC_BASE0 + MCFFEC_SIZE0 - 1,
.flags = IORESOURCE_MEM,
},
{
......@@ -73,8 +73,8 @@ static struct resource m527x_fec0_resources[] = {
static struct resource m527x_fec1_resources[] = {
{
.start = MCF_MBAR + 0x1800,
.end = MCF_MBAR + 0x1800 + 0x7ff,
.start = MCFFEC_BASE1,
.end = MCFFEC_BASE1 + MCFFEC_SIZE1 - 1,
.flags = IORESOURCE_MEM,
},
{
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册