ARM: Kirkwood: checkpatch cleanups

Mostly printk to pr_{err|info} changes and a few strings split over
multiple lines are combined.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

arch/arm/mach-kirkwood/board-dt.c

@@ -98,7 +98,7 @@ static void __init kirkwood_dt_init(void)
 			     kirkwood_auxdata_lookup, NULL);
 }
 
-static const char *kirkwood_dt_board_compat[] = {
+static const char * const kirkwood_dt_board_compat[] = {
 	"globalscale,dreamplug",
 	"dlink,dns-320",
 	"dlink,dns-325",

arch/arm/mach-kirkwood/common.c

@@ -18,10 +18,10 @@
 #include <linux/clk-provider.h>
 #include <linux/spinlock.h>
 #include <linux/mv643xx_i2c.h>
+#include <linux/timex.h>
+#include <linux/kexec.h>
 #include <net/dsa.h>
 #include <asm/page.h>
-#include <asm/timex.h>
-#include <asm/kexec.h>
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>
 #include <mach/kirkwood.h>
@@ -646,8 +646,7 @@ void __init kirkwood_l2_init(void)
 
 void __init kirkwood_init(void)
 {
-	printk(KERN_INFO "Kirkwood: %s, TCLK=%d.\n",
-		kirkwood_id(), kirkwood_tclk);
+	pr_info("Kirkwood: %s, TCLK=%d.\n", kirkwood_id(), kirkwood_tclk);
 
 	/*
 	 * Disable propagation of mbus errors to the CPU local bus,
@@ -671,7 +670,7 @@ void __init kirkwood_init(void)
 	kirkwood_xor1_init();
 	kirkwood_crypto_init();
 
-#ifdef CONFIG_KEXEC 
+#ifdef CONFIG_KEXEC
 	kexec_reinit = kirkwood_enable_pcie;
 #endif
 }

arch/arm/mach-kirkwood/common.h

@@ -47,7 +47,8 @@ void kirkwood_i2c_init(void);
 void kirkwood_uart0_init(void);
 void kirkwood_uart1_init(void);
 void kirkwood_nand_init(struct mtd_partition *parts, int nr_parts, int delay);
-void kirkwood_nand_init_rnb(struct mtd_partition *parts, int nr_parts, int (*dev_ready)(struct mtd_info *));
+void kirkwood_nand_init_rnb(struct mtd_partition *parts, int nr_parts,
+			    int (*dev_ready)(struct mtd_info *));
 void kirkwood_audio_init(void);
 void kirkwood_restart(char, const char *);
 void kirkwood_clk_init(void);

arch/arm/mach-kirkwood/cpuidle.c

@@ -64,7 +64,7 @@ static int kirkwood_init_cpuidle(void)
 
 	cpuidle_register_driver(&kirkwood_idle_driver);
 	if (cpuidle_register_device(device)) {
-		printk(KERN_ERR "kirkwood_init_cpuidle: Failed registering\n");
+		pr_err("kirkwood_init_cpuidle: Failed registering\n");
 		return -EIO;
 	}
 	return 0;

arch/arm/mach-kirkwood/dockstar-setup.c

@@ -93,7 +93,7 @@ static void __init dockstar_init(void)
 
 	if (gpio_request(29, "USB Power Enable") != 0 ||
 	    gpio_direction_output(29, 1) != 0)
-		printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n");
+		pr_err("can't set up GPIO 29 (USB Power Enable)\n");
 	kirkwood_ehci_init();
 
 	kirkwood_ge00_init(&dockstar_ge00_data);

arch/arm/mach-kirkwood/mpp.c

@@ -30,8 +30,8 @@ static unsigned int __init kirkwood_variant(void)
 	if (dev == MV88F6180_DEV_ID)
 		return MPP_F6180_MASK;
 
-	printk(KERN_ERR "MPP setup: unknown kirkwood variant "
-			"(dev %#x rev %#x)\n", dev, rev);
+	pr_err("MPP setup: unknown kirkwood variant (dev %#x rev %#x)\n",
+	       dev, rev);
 	return 0;
 }
 

arch/arm/mach-kirkwood/netspace_v2-setup.c

@@ -79,7 +79,7 @@ static struct platform_device netspace_v2_gpio_buttons = {
 	.name		= "gpio-keys",
 	.id		= -1,
 	.dev		= {
-		.platform_data 	= &netspace_v2_button_data,
+		.platform_data	= &netspace_v2_button_data,
 	},
 };
 
@@ -211,7 +211,7 @@ static unsigned int netspace_v2_mpp_config[] __initdata = {
 	MPP29_GPIO,		/* Blue led (slow register) */
 	MPP30_GPIO,		/* Blue led (command register) */
 	MPP31_GPIO,		/* Board power off */
-	MPP32_GPIO, 		/* Power button (0 = Released, 1 = Pushed) */
+	MPP32_GPIO,		/* Power button (0 = Released, 1 = Pushed) */
 	MPP33_GPO,		/* Fan speed (bit 2) */
 	0
 };

arch/arm/mach-kirkwood/openrd-setup.c

@@ -121,14 +121,12 @@ static int __init uart1_mpp_config(void)
 	kirkwood_mpp_conf(openrd_uart1_mpp_config);
 
 	if (gpio_request(34, "SD_UART1_SEL")) {
-		printk(KERN_ERR "GPIO request failed for SD/UART1 selection"
-				", gpio: 34\n");
+		pr_err("GPIO request 34 failed for SD/UART1 selection\n");
 		return -EIO;
 	}
 
 	if (gpio_request(28, "RS232_RS485_SEL")) {
-		printk(KERN_ERR "GPIO request failed for RS232/RS485 selection"
-				", gpio# 28\n");
+		pr_err("GPIO request 28 failed for RS232/RS485 selection\n");
 		gpio_free(34);
 		return -EIO;
 	}
@@ -185,15 +183,13 @@ static void __init openrd_init(void)
 
 	if (uart1 <= 0) {
 		if (uart1 < 0)
-			printk(KERN_ERR "Invalid kernel parameter to select "
-				"UART1. Defaulting to SD. ERROR CODE: %d\n",
-				uart1);
+			pr_err("Invalid kernel parameter to select UART1. Defaulting to SD. ERROR CODE: %d\n",
+			       uart1);
 
 		/* Select SD
 		 * Pin # 34: 0 => UART1, 1 => SD */
 		if (gpio_request(34, "SD_UART1_SEL")) {
-			printk(KERN_ERR "GPIO request failed for SD/UART1 "
-					"selection, gpio: 34\n");
+			pr_err("GPIO request 34 failed for SD/UART1 selection\n");
 		} else {
 
 			gpio_direction_output(34, 1);

arch/arm/mach-kirkwood/pcie.c

@@ -26,7 +26,7 @@ static void kirkwood_enable_pcie_clk(const char *port)
 
 	clk = clk_get_sys("pcie", port);
 	if (IS_ERR(clk)) {
-		printk(KERN_ERR "PCIE clock %s missing\n", port);
+		pr_err("PCIE clock %s missing\n", port);
 		return;
 	}
 	clk_prepare_enable(clk);
@@ -168,7 +168,7 @@ static int __init kirkwood_pcie_setup(int nr, struct pci_sys_data *sys)
 		return 0;
 
 	index = pcie_port_map[nr];
-	printk(KERN_INFO "PCI: bus%d uses PCIe port %d\n", sys->busnr, index);
+	pr_info("PCI: bus%d uses PCIe port %d\n", sys->busnr, index);
 
 	pp = kzalloc(sizeof(*pp), GFP_KERNEL);
 	if (!pp)
@@ -186,7 +186,8 @@ static int __init kirkwood_pcie_setup(int nr, struct pci_sys_data *sys)
 	case 1:
 		kirkwood_enable_pcie_clk("1");
 		pcie1_ioresources_init(pp);
-		pci_ioremap_io(SZ_64K * sys->busnr, KIRKWOOD_PCIE1_IO_PHYS_BASE);
+		pci_ioremap_io(SZ_64K * sys->busnr,
+			       KIRKWOOD_PCIE1_IO_PHYS_BASE);
 		break;
 	default:
 		panic("PCIe setup: invalid controller %d", index);
@@ -257,13 +258,13 @@ static struct hw_pci kirkwood_pci __initdata = {
 
 static void __init add_pcie_port(int index, void __iomem *base)
 {
-	printk(KERN_INFO "Kirkwood PCIe port %d: ", index);
+	pr_info("Kirkwood PCIe port %d: ", index);
 
 	if (orion_pcie_link_up(base)) {
-		printk(KERN_INFO "link up\n");
+		pr_info("link up\n");
 		pcie_port_map[num_pcie_ports++] = index;
 	} else
-		printk(KERN_INFO "link down, ignoring\n");
+		pr_info("link down, ignoring\n");
 }
 
 void __init kirkwood_pcie_init(unsigned int portmask)

arch/arm/mach-kirkwood/sheevaplug-setup.c

@@ -117,7 +117,7 @@ static void __init sheevaplug_init(void)
 
 	if (gpio_request(29, "USB Power Enable") != 0 ||
 	    gpio_direction_output(29, 1) != 0)
-		printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n");
+		pr_err("can't set up GPIO 29 (USB Power Enable)\n");
 	kirkwood_ehci_init();
 
 	kirkwood_ge00_init(&sheevaplug_ge00_data);

arch/arm/mach-kirkwood/ts41x-setup.c

@@ -170,8 +170,7 @@ static int __init ts41x_pci_init(void)
 		else
 			kirkwood_pcie_init(KW_PCIE0);
 	}
-
-   return 0;
+	return 0;
 }
 subsys_initcall(ts41x_pci_init);