m68k: drop unused Kconfig symbols

Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

arch/m68k/Kconfig.devices

@@ -77,32 +77,6 @@ config MULTIFACE_III_TTY
 
 	  To compile this driver as a module, choose M here.
 
-config GVPIOEXT
-	tristate "GVP IO-Extender support"
-	depends on PARPORT=n && ZORRO
-	help
-	  If you want to use a GVP IO-Extender serial card in Linux, say Y.
-	  Otherwise, say N.
-
-config GVPIOEXT_LP
-	tristate "GVP IO-Extender parallel printer support"
-	depends on GVPIOEXT
-	help
-	  Say Y to enable driving a printer from the parallel port on your
-	  GVP IO-Extender card, N otherwise.
-
-config GVPIOEXT_PLIP
-	tristate "GVP IO-Extender PLIP support"
-	depends on GVPIOEXT
-	help
-	  Say Y to enable doing IP over the parallel port on your GVP
-	  IO-Extender card, N otherwise.
-
-config MAC_HID
-	bool
-	depends on INPUT_ADBHID
-	default y
-
 config HPDCA
 	tristate "HP DCA serial support"
 	depends on DIO && SERIAL_8250
@@ -145,7 +119,7 @@ config DN_SERIAL
 
 config SERIAL_CONSOLE
 	bool "Support for serial port console"
-	depends on (AMIGA || ATARI || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_MIDI=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL)
+	depends on (AMIGA || ATARI || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_MIDI=y || AMIGA_BUILTIN_SERIAL=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL)
 	---help---
 	  If you say Y here, it will be possible to use a serial port as the
 	  system console (the system console is the device which receives all

arch/m68k/Kconfig.machine

@@ -303,9 +303,6 @@ config COBRA5282
 	help
 	  Support for the senTec COBRA5282 board.
 
-config EMAC_INC
-	bool
-
 config SOM5282EM
 	bool "EMAC.Inc SOM5282EM board support"
 	depends on M528x
@@ -371,27 +368,21 @@ config FIREBEE
 	help
 	  Support for the FireBee ColdFire 5475 based board.
 
-config HW_FEITH
-	bool
-
 config CLEOPATRA
 	bool "Feith CLEOPATRA board support"
 	depends on (M5307 || M5407)
-	select HW_FEITH
 	help
 	  Support for the Feith Cleopatra boards.
 
 config CANCam
 	bool "Feith CANCam board support"
 	depends on M5272
-	select HW_FEITH
 	help
 	  Support for the Feith CANCam board.
 
 config SCALES
 	bool "Feith SCALES board support"
 	depends on M5272
-	select HW_FEITH
 	help
 	  Support for the Feith SCALES board.
 
@@ -438,13 +429,6 @@ if !MMU || COLDFIRE
 
 comment "Machine Options"
 
-config ROMFS_FROM_ROM
-	bool "ROMFS image not RAM resident"
-	depends on (NETtel || SNAPGEAR)
-	help
-	  The ROMfs filesystem will stay resident in the FLASH/ROM, not be
-	  moved into RAM.
-
 config UBOOT
 	bool "Support for U-Boot command line parameters"
 	help
@@ -524,33 +508,6 @@ config KERNELBASE
 	  a system with the RAM based at address 0, and leaving enough room
 	  for the theoretical maximum number of 256 vectors.
 
-choice
-	prompt "RAM bus width"
-	default RAMAUTOBIT
-
-config RAMAUTOBIT
-	bool "AUTO"
-	help
-	  Select the physical RAM data bus size. Not needed on most platforms,
-	  so you can generally choose AUTO.
-
-config RAM8BIT
-	bool "8bit"
-	help
-	  Configure RAM bus to be 8 bits wide.
-
-config RAM16BIT
-	bool "16bit"
-	help
-	  Configure RAM bus to be 16 bits wide.
-
-config RAM32BIT
-	bool "32bit"
-	help
-	  Configure RAM bus to be 32 bits wide.
-
-endchoice
-
 comment "ROM configuration"
 
 config ROM