davinci: DM355: add base SoC and board support

In addition, add board support for the DM355 Evaluation Module (EVM)
and the DM355 Leopard board.

Original DM355 EVM support done by Sandeep Paulraj, with significant
updates and improvements by David Brownell.  DM355 Leopord support
done by Koen Kooi.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKoen Kooi <koen@beagleboard.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

arch/arm/mach-davinci/Kconfig

@@ -10,6 +10,9 @@ comment "DaVinci Core Type"
 config ARCH_DAVINCI_DM644x
 	bool "DaVinci 644x based system"
 
+config ARCH_DAVINCI_DM355
+        bool "DaVinci 355 based system"
+
 comment "DaVinci Board Type"
 
 config MACH_DAVINCI_EVM
@@ -28,6 +31,22 @@ config MACH_SFFSDR
 	  Say Y here to select the Lyrtech Small Form Factor
 	  Software Defined Radio (SFFSDR) board.
 
+config MACH_DAVINCI_DM355_EVM
+	bool "TI DM355 EVM"
+	default n
+	depends on ARCH_DAVINCI_DM355
+	help
+	  Configure this option to specify the whether the board used
+	  for development is a DM355 EVM
+
+config MACH_DM355_LEOPARD
+	bool "DM355 Leopard board"
+	default n
+	depends on ARCH_DAVINCI_DM355
+	help
+	  Configure this option to specify the whether the board used
+	  for development is a DM355 Leopard board.
+
 config DAVINCI_MUX
 	bool "DAVINCI multiplexing support"
 	depends on ARCH_DAVINCI

arch/arm/mach-davinci/Makefile

@@ -12,7 +12,10 @@ obj-$(CONFIG_CP_INTC)			+= cp_intc.o
 
 # Chip specific
 obj-$(CONFIG_ARCH_DAVINCI_DM644x)       += dm644x.o
+obj-$(CONFIG_ARCH_DAVINCI_DM355)        += dm355.o
 
 # Board specific
 obj-$(CONFIG_MACH_DAVINCI_EVM)  	+= board-dm644x-evm.o
 obj-$(CONFIG_MACH_SFFSDR)		+= board-sffsdr.o
+obj-$(CONFIG_MACH_DAVINCI_DM355_EVM)	+= board-dm355-evm.o
+obj-$(CONFIG_MACH_DM355_LEOPARD)	+= board-dm355-leopard.o

arch/arm/mach-davinci/board-dm355-evm.c

+/*
+ * TI DaVinci EVM board support
+ *
+ * Author: Kevin Hilman, Deep Root Systems, LLC
+ *
+ * 2007 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/nand.h>
+#include <linux/i2c.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/clk.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/eeprom.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/flash.h>
+
+#include <mach/hardware.h>
+#include <mach/dm355.h>
+#include <mach/psc.h>
+#include <mach/common.h>
+#include <mach/i2c.h>
+#include <mach/serial.h>
+#include <mach/nand.h>
+
+#define DAVINCI_ASYNC_EMIF_CONTROL_BASE		0x01e10000
+#define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE	0x02000000
+
+/* NOTE:  this is geared for the standard config, with a socketed
+ * 2 GByte Micron NAND (MT29F16G08FAA) using 128KB sectors.  If you
+ * swap chips, maybe with a different block size, partitioning may
+ * need to be changed.
+ */
+#define NAND_BLOCK_SIZE		SZ_128K
+
+static struct mtd_partition davinci_nand_partitions[] = {
+	{
+		/* UBL (a few copies) plus U-Boot */
+		.name		= "bootloader",
+		.offset		= 0,
+		.size		= 15 * NAND_BLOCK_SIZE,
+		.mask_flags	= MTD_WRITEABLE, /* force read-only */
+	}, {
+		/* U-Boot environment */
+		.name		= "params",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= 1 * NAND_BLOCK_SIZE,
+		.mask_flags	= 0,
+	}, {
+		.name		= "kernel",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= SZ_4M,
+		.mask_flags	= 0,
+	}, {
+		.name		= "filesystem1",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= SZ_512M,
+		.mask_flags	= 0,
+	}, {
+		.name		= "filesystem2",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= MTDPART_SIZ_FULL,
+		.mask_flags	= 0,
+	}
+	/* two blocks with bad block table (and mirror) at the end */
+};
+
+static struct davinci_nand_pdata davinci_nand_data = {
+	.mask_chipsel		= BIT(14),
+	.parts			= davinci_nand_partitions,
+	.nr_parts		= ARRAY_SIZE(davinci_nand_partitions),
+	.ecc_mode		= NAND_ECC_HW_SYNDROME,
+	.options		= NAND_USE_FLASH_BBT,
+};
+
+static struct resource davinci_nand_resources[] = {
+	{
+		.start		= DAVINCI_ASYNC_EMIF_DATA_CE0_BASE,
+		.end		= DAVINCI_ASYNC_EMIF_DATA_CE0_BASE + SZ_32M - 1,
+		.flags		= IORESOURCE_MEM,
+	}, {
+		.start		= DAVINCI_ASYNC_EMIF_CONTROL_BASE,
+		.end		= DAVINCI_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1,
+		.flags		= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device davinci_nand_device = {
+	.name			= "davinci_nand",
+	.id			= 0,
+
+	.num_resources		= ARRAY_SIZE(davinci_nand_resources),
+	.resource		= davinci_nand_resources,
+
+	.dev			= {
+		.platform_data	= &davinci_nand_data,
+	},
+};
+
+static struct davinci_i2c_platform_data i2c_pdata = {
+	.bus_freq	= 400	/* kHz */,
+	.bus_delay	= 0	/* usec */,
+};
+
+static int dm355evm_mmc_gpios = -EINVAL;
+
+static void dm355evm_mmcsd_gpios(unsigned gpio)
+{
+	gpio_request(gpio + 0, "mmc0_ro");
+	gpio_request(gpio + 1, "mmc0_cd");
+	gpio_request(gpio + 2, "mmc1_ro");
+	gpio_request(gpio + 3, "mmc1_cd");
+
+	/* we "know" these are input-only so we don't
+	 * need to call gpio_direction_input()
+	 */
+
+	dm355evm_mmc_gpios = gpio;
+}
+
+static struct i2c_board_info dm355evm_i2c_info[] = {
+	{ I2C_BOARD_INFO("dm355evm_msp", 0x25),
+		.platform_data = dm355evm_mmcsd_gpios,
+		/* plus irq */ },
+	/* { I2C_BOARD_INFO("tlv320aic3x", 0x1b), }, */
+	/* { I2C_BOARD_INFO("tvp5146", 0x5d), }, */
+};
+
+static void __init evm_init_i2c(void)
+{
+	davinci_init_i2c(&i2c_pdata);
+
+	gpio_request(5, "dm355evm_msp");
+	gpio_direction_input(5);
+	dm355evm_i2c_info[0].irq = gpio_to_irq(5);
+
+	i2c_register_board_info(1, dm355evm_i2c_info,
+			ARRAY_SIZE(dm355evm_i2c_info));
+}
+
+static struct resource dm355evm_dm9000_rsrc[] = {
+	{
+		/* addr */
+		.start	= 0x04014000,
+		.end	= 0x04014001,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		/* data */
+		.start	= 0x04014002,
+		.end	= 0x04014003,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags	= IORESOURCE_IRQ
+			| IORESOURCE_IRQ_HIGHEDGE /* rising (active high) */,
+	},
+};
+
+static struct platform_device dm355evm_dm9000 = {
+	.name		= "dm9000",
+	.id		= -1,
+	.resource	= dm355evm_dm9000_rsrc,
+	.num_resources	= ARRAY_SIZE(dm355evm_dm9000_rsrc),
+};
+
+static struct platform_device *davinci_evm_devices[] __initdata = {
+	&dm355evm_dm9000,
+	&davinci_nand_device,
+};
+
+static struct davinci_uart_config uart_config __initdata = {
+	.enabled_uarts = (1 << 0),
+};
+
+static void __init dm355_evm_map_io(void)
+{
+	davinci_map_common_io();
+	dm355_init();
+}
+
+/* Don't connect anything to J10 unless you're only using USB host
+ * mode *and* have to do so with some kind of gender-bender.  If
+ * you have proper Mini-B or Mini-A cables (or Mini-A adapters)
+ * the ID pin won't need any help.
+ */
+#ifdef CONFIG_USB_MUSB_PERIPHERAL
+#define USB_ID_VALUE	0	/* ID pulled high; *should* float */
+#else
+#define USB_ID_VALUE	1	/* ID pulled low */
+#endif
+
+static struct spi_eeprom at25640a = {
+	.byte_len	= SZ_64K / 8,
+	.name		= "at25640a",
+	.page_size	= 32,
+	.flags		= EE_ADDR2,
+};
+
+static struct spi_board_info dm355_evm_spi_info[] __initconst = {
+	{
+		.modalias	= "at25",
+		.platform_data	= &at25640a,
+		.max_speed_hz	= 10 * 1000 * 1000,	/* at 3v3 */
+		.bus_num	= 0,
+		.chip_select	= 0,
+		.mode		= SPI_MODE_0,
+	},
+};
+
+static __init void dm355_evm_init(void)
+{
+	struct clk *aemif;
+
+	gpio_request(1, "dm9000");
+	gpio_direction_input(1);
+	dm355evm_dm9000_rsrc[2].start = gpio_to_irq(1);
+
+	aemif = clk_get(&dm355evm_dm9000.dev, "aemif");
+	if (IS_ERR(aemif))
+		WARN("%s: unable to get AEMIF clock\n", __func__);
+	else
+		clk_enable(aemif);
+
+	platform_add_devices(davinci_evm_devices,
+			     ARRAY_SIZE(davinci_evm_devices));
+	evm_init_i2c();
+	davinci_serial_init(&uart_config);
+
+	/* NOTE:  NAND flash timings set by the UBL are slower than
+	 * needed by MT29F16G08FAA chips ... EMIF.A1CR is 0x40400204
+	 * but could be 0x0400008c for about 25% faster page reads.
+	 */
+
+	gpio_request(2, "usb_id_toggle");
+	gpio_direction_output(2, USB_ID_VALUE);
+	/* irlml6401 switches over 1A in under 8 msec */
+	setup_usb(500, 8);
+
+	dm355_init_spi0(BIT(0), dm355_evm_spi_info,
+			ARRAY_SIZE(dm355_evm_spi_info));
+}
+
+static __init void dm355_evm_irq_init(void)
+{
+	davinci_irq_init();
+}
+
+MACHINE_START(DAVINCI_DM355_EVM, "DaVinci DM355 EVM")
+	.phys_io      = IO_PHYS,
+	.io_pg_offst  = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
+	.boot_params  = (0x80000100),
+	.map_io	      = dm355_evm_map_io,
+	.init_irq     = dm355_evm_irq_init,
+	.timer	      = &davinci_timer,
+	.init_machine = dm355_evm_init,
+MACHINE_END

arch/arm/mach-davinci/board-dm355-leopard.c

+/*
+ * DM355 leopard board support
+ *
+ * Based on board-dm355-evm.c
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/nand.h>
+#include <linux/i2c.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/clk.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/eeprom.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/flash.h>
+
+#include <mach/hardware.h>
+#include <mach/dm355.h>
+#include <mach/psc.h>
+#include <mach/common.h>
+#include <mach/i2c.h>
+#include <mach/serial.h>
+#include <mach/nand.h>
+
+#define DAVINCI_ASYNC_EMIF_CONTROL_BASE		0x01e10000
+#define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE	0x02000000
+
+/* NOTE:  this is geared for the standard config, with a socketed
+ * 2 GByte Micron NAND (MT29F16G08FAA) using 128KB sectors.  If you
+ * swap chips, maybe with a different block size, partitioning may
+ * need to be changed.
+ */
+#define NAND_BLOCK_SIZE		SZ_128K
+
+static struct mtd_partition davinci_nand_partitions[] = {
+	{
+		/* UBL (a few copies) plus U-Boot */
+		.name		= "bootloader",
+		.offset		= 0,
+		.size		= 15 * NAND_BLOCK_SIZE,
+		.mask_flags	= MTD_WRITEABLE, /* force read-only */
+	}, {
+		/* U-Boot environment */
+		.name		= "params",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= 1 * NAND_BLOCK_SIZE,
+		.mask_flags	= 0,
+	}, {
+		.name		= "kernel",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= SZ_4M,
+		.mask_flags	= 0,
+	}, {
+		.name		= "filesystem1",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= SZ_512M,
+		.mask_flags	= 0,
+	}, {
+		.name		= "filesystem2",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= MTDPART_SIZ_FULL,
+		.mask_flags	= 0,
+	}
+	/* two blocks with bad block table (and mirror) at the end */
+};
+
+static struct davinci_nand_pdata davinci_nand_data = {
+	.mask_chipsel		= BIT(14),
+	.parts			= davinci_nand_partitions,
+	.nr_parts		= ARRAY_SIZE(davinci_nand_partitions),
+	.ecc_mode		= NAND_ECC_HW_SYNDROME,
+	.options		= NAND_USE_FLASH_BBT,
+};
+
+static struct resource davinci_nand_resources[] = {
+	{
+		.start		= DAVINCI_ASYNC_EMIF_DATA_CE0_BASE,
+		.end		= DAVINCI_ASYNC_EMIF_DATA_CE0_BASE + SZ_32M - 1,
+		.flags		= IORESOURCE_MEM,
+	}, {
+		.start		= DAVINCI_ASYNC_EMIF_CONTROL_BASE,
+		.end		= DAVINCI_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1,
+		.flags		= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device davinci_nand_device = {
+	.name			= "davinci_nand",
+	.id			= 0,
+
+	.num_resources		= ARRAY_SIZE(davinci_nand_resources),
+	.resource		= davinci_nand_resources,
+
+	.dev			= {
+		.platform_data	= &davinci_nand_data,
+	},
+};
+
+static struct davinci_i2c_platform_data i2c_pdata = {
+	.bus_freq	= 400	/* kHz */,
+	.bus_delay	= 0	/* usec */,
+};
+
+static int leopard_mmc_gpio = -EINVAL;
+
+static void dm355leopard_mmcsd_gpios(unsigned gpio)
+{
+	gpio_request(gpio + 0, "mmc0_ro");
+	gpio_request(gpio + 1, "mmc0_cd");
+	gpio_request(gpio + 2, "mmc1_ro");
+	gpio_request(gpio + 3, "mmc1_cd");
+
+	/* we "know" these are input-only so we don't
+	 * need to call gpio_direction_input()
+	 */
+
+	leopard_mmc_gpio = gpio;
+}
+
+static struct i2c_board_info dm355leopard_i2c_info[] = {
+	{ I2C_BOARD_INFO("dm355leopard_msp", 0x25),
+		.platform_data = dm355leopard_mmcsd_gpios,
+		/* plus irq */ },
+	/* { I2C_BOARD_INFO("tlv320aic3x", 0x1b), }, */
+	/* { I2C_BOARD_INFO("tvp5146", 0x5d), }, */
+};
+
+static void __init leopard_init_i2c(void)
+{
+	davinci_init_i2c(&i2c_pdata);
+
+	gpio_request(5, "dm355leopard_msp");
+	gpio_direction_input(5);
+	dm355leopard_i2c_info[0].irq = gpio_to_irq(5);
+
+	i2c_register_board_info(1, dm355leopard_i2c_info,
+			ARRAY_SIZE(dm355leopard_i2c_info));
+}
+
+static struct resource dm355leopard_dm9000_rsrc[] = {
+	{
+		/* addr */
+		.start	= 0x04000000,
+		.end	= 0x04000001,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		/* data */
+		.start	= 0x04000016,
+		.end	= 0x04000017,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags	= IORESOURCE_IRQ
+			| IORESOURCE_IRQ_HIGHEDGE /* rising (active high) */,
+	},
+};
+
+static struct platform_device dm355leopard_dm9000 = {
+	.name		= "dm9000",
+	.id		= -1,
+	.resource	= dm355leopard_dm9000_rsrc,
+	.num_resources	= ARRAY_SIZE(dm355leopard_dm9000_rsrc),
+};
+
+static struct platform_device *davinci_leopard_devices[] __initdata = {
+	&dm355leopard_dm9000,
+	&davinci_nand_device,
+};
+
+static struct davinci_uart_config uart_config __initdata = {
+	.enabled_uarts = (1 << 0),
+};
+
+static void __init dm355_leopard_map_io(void)
+{
+	davinci_map_common_io();
+	dm355_init();
+}
+
+/* Don't connect anything to J10 unless you're only using USB host
+ * mode *and* have to do so with some kind of gender-bender.  If
+ * you have proper Mini-B or Mini-A cables (or Mini-A adapters)
+ * the ID pin won't need any help.
+ */
+#ifdef CONFIG_USB_MUSB_PERIPHERAL
+#define USB_ID_VALUE	0	/* ID pulled high; *should* float */
+#else
+#define USB_ID_VALUE	1	/* ID pulled low */
+#endif
+
+static struct spi_eeprom at25640a = {
+	.byte_len	= SZ_64K / 8,
+	.name		= "at25640a",
+	.page_size	= 32,
+	.flags		= EE_ADDR2,
+};
+
+static struct spi_board_info dm355_leopard_spi_info[] __initconst = {
+	{
+		.modalias	= "at25",
+		.platform_data	= &at25640a,
+		.max_speed_hz	= 10 * 1000 * 1000,	/* at 3v3 */
+		.bus_num	= 0,
+		.chip_select	= 0,
+		.mode		= SPI_MODE_0,
+	},
+};
+
+static __init void dm355_leopard_init(void)
+{
+	struct clk *aemif;
+
+	gpio_request(9, "dm9000");
+	gpio_direction_input(9);
+	dm355leopard_dm9000_rsrc[2].start = gpio_to_irq(9);
+
+	aemif = clk_get(&dm355leopard_dm9000.dev, "aemif");
+	if (IS_ERR(aemif))
+		WARN("%s: unable to get AEMIF clock\n", __func__);
+	else
+		clk_enable(aemif);
+
+	platform_add_devices(davinci_leopard_devices,
+			     ARRAY_SIZE(davinci_leopard_devices));
+	leopard_init_i2c();
+	davinci_serial_init(&uart_config);
+
+	/* NOTE:  NAND flash timings set by the UBL are slower than
+	 * needed by MT29F16G08FAA chips ... EMIF.A1CR is 0x40400204
+	 * but could be 0x0400008c for about 25% faster page reads.
+	 */
+
+	gpio_request(2, "usb_id_toggle");
+	gpio_direction_output(2, USB_ID_VALUE);
+	/* irlml6401 switches over 1A in under 8 msec */
+	setup_usb(500, 8);
+
+	dm355_init_spi0(BIT(0), dm355_leopard_spi_info,
+			ARRAY_SIZE(dm355_leopard_spi_info));
+}
+
+static __init void dm355_leopard_irq_init(void)
+{
+	davinci_irq_init();
+}
+
+MACHINE_START(DM355_LEOPARD, "DaVinci DM355 leopard")
+	.phys_io      = IO_PHYS,
+	.io_pg_offst  = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
+	.boot_params  = (0x80000100),
+	.map_io	      = dm355_leopard_map_io,
+	.init_irq     = dm355_leopard_irq_init,
+	.timer	      = &davinci_timer,
+	.init_machine = dm355_leopard_init,
+MACHINE_END

arch/arm/mach-davinci/dm355.c

+/*
+ * TI DaVinci DM355 chip specific setup
+ *
+ * Author: Kevin Hilman, Deep Root Systems, LLC
+ *
+ * 2007 (c) Deep Root Systems, LLC. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/clk.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+
+#include <linux/spi/spi.h>
+
+#include <mach/dm355.h>
+#include <mach/clock.h>
+#include <mach/cputype.h>
+#include <mach/edma.h>
+#include <mach/psc.h>
+#include <mach/mux.h>
+#include <mach/irqs.h>
+
+#include "clock.h"
+#include "mux.h"
+
+/*
+ * Device specific clocks
+ */
+#define DM355_REF_FREQ		24000000	/* 24 or 36 MHz */
+
+static struct pll_data pll1_data = {
+	.num       = 1,
+	.phys_base = DAVINCI_PLL1_BASE,
+	.flags     = PLL_HAS_PREDIV | PLL_HAS_POSTDIV,
+};
+
+static struct pll_data pll2_data = {
+	.num       = 2,
+	.phys_base = DAVINCI_PLL2_BASE,
+	.flags     = PLL_HAS_PREDIV,
+};
+
+static struct clk ref_clk = {
+	.name = "ref_clk",
+	/* FIXME -- crystal rate is board-specific */
+	.rate = DM355_REF_FREQ,
+};
+
+static struct clk pll1_clk = {
+	.name = "pll1",
+	.parent = &ref_clk,
+	.flags = CLK_PLL,
+	.pll_data = &pll1_data,
+};
+
+static struct clk pll1_aux_clk = {
+	.name = "pll1_aux_clk",
+	.parent = &pll1_clk,
+	.flags = CLK_PLL | PRE_PLL,
+};
+
+static struct clk pll1_sysclk1 = {
+	.name = "pll1_sysclk1",
+	.parent = &pll1_clk,
+	.flags = CLK_PLL,
+	.div_reg = PLLDIV1,
+};
+
+static struct clk pll1_sysclk2 = {
+	.name = "pll1_sysclk2",
+	.parent = &pll1_clk,
+	.flags = CLK_PLL,
+	.div_reg = PLLDIV2,
+};
+
+static struct clk pll1_sysclk3 = {
+	.name = "pll1_sysclk3",
+	.parent = &pll1_clk,
+	.flags = CLK_PLL,
+	.div_reg = PLLDIV3,
+};
+
+static struct clk pll1_sysclk4 = {
+	.name = "pll1_sysclk4",
+	.parent = &pll1_clk,
+	.flags = CLK_PLL,
+	.div_reg = PLLDIV4,
+};
+
+static struct clk pll1_sysclkbp = {
+	.name = "pll1_sysclkbp",
+	.parent = &pll1_clk,
+	.flags = CLK_PLL | PRE_PLL,
+	.div_reg = BPDIV
+};
+
+static struct clk vpss_dac_clk = {
+	.name = "vpss_dac",
+	.parent = &pll1_sysclk3,
+	.lpsc = DM355_LPSC_VPSS_DAC,
+};
+
+static struct clk vpss_master_clk = {
+	.name = "vpss_master",
+	.parent = &pll1_sysclk4,
+	.lpsc = DAVINCI_LPSC_VPSSMSTR,
+	.flags = CLK_PSC,
+};
+
+static struct clk vpss_slave_clk = {
+	.name = "vpss_slave",
+	.parent = &pll1_sysclk4,
+	.lpsc = DAVINCI_LPSC_VPSSSLV,
+};
+
+
+static struct clk clkout1_clk = {
+	.name = "clkout1",
+	.parent = &pll1_aux_clk,
+	/* NOTE:  clkout1 can be externally gated by muxing GPIO-18 */
+};
+
+static struct clk clkout2_clk = {
+	.name = "clkout2",
+	.parent = &pll1_sysclkbp,
+};
+
+static struct clk pll2_clk = {
+	.name = "pll2",
+	.parent = &ref_clk,
+	.flags = CLK_PLL,
+	.pll_data = &pll2_data,
+};
+
+static struct clk pll2_sysclk1 = {
+	.name = "pll2_sysclk1",
+	.parent = &pll2_clk,
+	.flags = CLK_PLL,
+	.div_reg = PLLDIV1,
+};
+
+static struct clk pll2_sysclkbp = {
+	.name = "pll2_sysclkbp",
+	.parent = &pll2_clk,
+	.flags = CLK_PLL | PRE_PLL,
+	.div_reg = BPDIV
+};
+
+static struct clk clkout3_clk = {
+	.name = "clkout3",
+	.parent = &pll2_sysclkbp,
+	/* NOTE:  clkout3 can be externally gated by muxing GPIO-16 */
+};
+
+static struct clk arm_clk = {
+	.name = "arm_clk",
+	.parent = &pll1_sysclk1,
+	.lpsc = DAVINCI_LPSC_ARM,
+	.flags = ALWAYS_ENABLED,
+};
+
+/*
+ * NOT LISTED below, and not touched by Linux
+ *   - in SyncReset state by default
+ *	.lpsc = DAVINCI_LPSC_TPCC,
+ *	.lpsc = DAVINCI_LPSC_TPTC0,
+ *	.lpsc = DAVINCI_LPSC_TPTC1,
+ *	.lpsc = DAVINCI_LPSC_DDR_EMIF, .parent = &sysclk2_clk,
+ *	.lpsc = DAVINCI_LPSC_MEMSTICK,
+ *   - in Enabled state by default
+ *	.lpsc = DAVINCI_LPSC_SYSTEM_SUBSYS,
+ *	.lpsc = DAVINCI_LPSC_SCR2,	// "bus"
+ *	.lpsc = DAVINCI_LPSC_SCR3,	// "bus"
+ *	.lpsc = DAVINCI_LPSC_SCR4,	// "bus"
+ *	.lpsc = DAVINCI_LPSC_CROSSBAR,	// "emulation"
+ *	.lpsc = DAVINCI_LPSC_CFG27,	// "test"
+ *	.lpsc = DAVINCI_LPSC_CFG3,	// "test"
+ *	.lpsc = DAVINCI_LPSC_CFG5,	// "test"
+ */
+
+static struct clk mjcp_clk = {
+	.name = "mjcp",
+	.parent = &pll1_sysclk1,
+	.lpsc = DAVINCI_LPSC_IMCOP,
+};
+
+static struct clk uart0_clk = {
+	.name = "uart0",
+	.parent = &pll1_aux_clk,
+	.lpsc = DAVINCI_LPSC_UART0,
+};
+
+static struct clk uart1_clk = {
+	.name = "uart1",
+	.parent = &pll1_aux_clk,
+	.lpsc = DAVINCI_LPSC_UART1,
+};
+
+static struct clk uart2_clk = {
+	.name = "uart2",
+	.parent = &pll1_sysclk2,
+	.lpsc = DAVINCI_LPSC_UART2,
+};
+
+static struct clk i2c_clk = {
+	.name = "i2c",
+	.parent = &pll1_aux_clk,
+	.lpsc = DAVINCI_LPSC_I2C,
+};
+
+static struct clk asp0_clk = {
+	.name = "asp0",
+	.parent = &pll1_sysclk2,
+	.lpsc = DAVINCI_LPSC_McBSP,
+};
+
+static struct clk asp1_clk = {
+	.name = "asp1",
+	.parent = &pll1_sysclk2,
+	.lpsc = DM355_LPSC_McBSP1,
+};
+
+static struct clk mmcsd0_clk = {
+	.name = "mmcsd0",
+	.parent = &pll1_sysclk2,
+	.lpsc = DAVINCI_LPSC_MMC_SD,
+};
+
+static struct clk mmcsd1_clk = {
+	.name = "mmcsd1",
+	.parent = &pll1_sysclk2,
+	.lpsc = DM355_LPSC_MMC_SD1,
+};
+
+static struct clk spi0_clk = {
+	.name = "spi0",
+	.parent = &pll1_sysclk2,
+	.lpsc = DAVINCI_LPSC_SPI,
+};
+
+static struct clk spi1_clk = {
+	.name = "spi1",
+	.parent = &pll1_sysclk2,
+	.lpsc = DM355_LPSC_SPI1,
+};
+
+static struct clk spi2_clk = {
+	.name = "spi2",
+	.parent = &pll1_sysclk2,
+	.lpsc = DM355_LPSC_SPI2,
+};
+
+static struct clk gpio_clk = {
+	.name = "gpio",
+	.parent = &pll1_sysclk2,
+	.lpsc = DAVINCI_LPSC_GPIO,
+};
+
+static struct clk aemif_clk = {
+	.name = "aemif",
+	.parent = &pll1_sysclk2,
+	.lpsc = DAVINCI_LPSC_AEMIF,
+};
+
+static struct clk pwm0_clk = {
+	.name = "pwm0",
+	.parent = &pll1_aux_clk,
+	.lpsc = DAVINCI_LPSC_PWM0,
+};
+
+static struct clk pwm1_clk = {
+	.name = "pwm1",
+	.parent = &pll1_aux_clk,
+	.lpsc = DAVINCI_LPSC_PWM1,
+};
+
+static struct clk pwm2_clk = {
+	.name = "pwm2",
+	.parent = &pll1_aux_clk,
+	.lpsc = DAVINCI_LPSC_PWM2,
+};
+
+static struct clk pwm3_clk = {
+	.name = "pwm3",
+	.parent = &pll1_aux_clk,
+	.lpsc = DM355_LPSC_PWM3,
+};
+
+static struct clk timer0_clk = {
+	.name = "timer0",
+	.parent = &pll1_aux_clk,
+	.lpsc = DAVINCI_LPSC_TIMER0,
+};
+
+static struct clk timer1_clk = {
+	.name = "timer1",
+	.parent = &pll1_aux_clk,
+	.lpsc = DAVINCI_LPSC_TIMER1,
+};
+
+static struct clk timer2_clk = {
+	.name = "timer2",
+	.parent = &pll1_aux_clk,
+	.lpsc = DAVINCI_LPSC_TIMER2,
+	.usecount = 1,              /* REVISIT: why cant' this be disabled? */
+};
+
+static struct clk timer3_clk = {
+	.name = "timer3",
+	.parent = &pll1_aux_clk,
+	.lpsc = DM355_LPSC_TIMER3,
+};
+
+static struct clk rto_clk = {
+	.name = "rto",
+	.parent = &pll1_aux_clk,
+	.lpsc = DM355_LPSC_RTO,
+};
+
+static struct clk usb_clk = {
+	.name = "usb",
+	.parent = &pll1_sysclk2,
+	.lpsc = DAVINCI_LPSC_USB,
+};
+
+static struct davinci_clk dm355_clks[] = {
+	CLK(NULL, "ref", &ref_clk),
+	CLK(NULL, "pll1", &pll1_clk),
+	CLK(NULL, "pll1_sysclk1", &pll1_sysclk1),
+	CLK(NULL, "pll1_sysclk2", &pll1_sysclk2),
+	CLK(NULL, "pll1_sysclk3", &pll1_sysclk3),
+	CLK(NULL, "pll1_sysclk4", &pll1_sysclk4),
+	CLK(NULL, "pll1_aux", &pll1_aux_clk),
+	CLK(NULL, "pll1_sysclkbp", &pll1_sysclkbp),
+	CLK(NULL, "vpss_dac", &vpss_dac_clk),
+	CLK(NULL, "vpss_master", &vpss_master_clk),
+	CLK(NULL, "vpss_slave", &vpss_slave_clk),
+	CLK(NULL, "clkout1", &clkout1_clk),
+	CLK(NULL, "clkout2", &clkout2_clk),
+	CLK(NULL, "pll2", &pll2_clk),
+	CLK(NULL, "pll2_sysclk1", &pll2_sysclk1),
+	CLK(NULL, "pll2_sysclkbp", &pll2_sysclkbp),
+	CLK(NULL, "clkout3", &clkout3_clk),
+	CLK(NULL, "arm", &arm_clk),
+	CLK(NULL, "mjcp", &mjcp_clk),
+	CLK(NULL, "uart0", &uart0_clk),
+	CLK(NULL, "uart1", &uart1_clk),
+	CLK(NULL, "uart2", &uart2_clk),
+	CLK("i2c_davinci.1", NULL, &i2c_clk),
+	CLK("soc-audio.0", NULL, &asp0_clk),
+	CLK("soc-audio.1", NULL, &asp1_clk),
+	CLK("davinci_mmc.0", NULL, &mmcsd0_clk),
+	CLK("davinci_mmc.1", NULL, &mmcsd1_clk),
+	CLK(NULL, "spi0", &spi0_clk),
+	CLK(NULL, "spi1", &spi1_clk),
+	CLK(NULL, "spi2", &spi2_clk),
+	CLK(NULL, "gpio", &gpio_clk),
+	CLK(NULL, "aemif", &aemif_clk),
+	CLK(NULL, "pwm0", &pwm0_clk),
+	CLK(NULL, "pwm1", &pwm1_clk),
+	CLK(NULL, "pwm2", &pwm2_clk),
+	CLK(NULL, "pwm3", &pwm3_clk),
+	CLK(NULL, "timer0", &timer0_clk),
+	CLK(NULL, "timer1", &timer1_clk),
+	CLK("watchdog", NULL, &timer2_clk),
+	CLK(NULL, "timer3", &timer3_clk),
+	CLK(NULL, "rto", &rto_clk),
+	CLK(NULL, "usb", &usb_clk),
+	CLK(NULL, NULL, NULL),
+};
+
+/*----------------------------------------------------------------------*/
+
+static u64 dm355_spi0_dma_mask = DMA_BIT_MASK(32);
+
+static struct resource dm355_spi0_resources[] = {
+	{
+		.start = 0x01c66000,
+		.end   = 0x01c667ff,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_DM355_SPINT0_1,
+		.flags = IORESOURCE_IRQ,
+	},
+	/* Not yet used, so not included:
+	 * IORESOURCE_IRQ:
+	 *  - IRQ_DM355_SPINT0_0
+	 * IORESOURCE_DMA:
+	 *  - DAVINCI_DMA_SPI_SPIX
+	 *  - DAVINCI_DMA_SPI_SPIR
+	 */
+};
+
+static struct platform_device dm355_spi0_device = {
+	.name = "spi_davinci",
+	.id = 0,
+	.dev = {
+		.dma_mask = &dm355_spi0_dma_mask,
+		.coherent_dma_mask = DMA_BIT_MASK(32),
+	},
+	.num_resources = ARRAY_SIZE(dm355_spi0_resources),
+	.resource = dm355_spi0_resources,
+};
+
+void __init dm355_init_spi0(unsigned chipselect_mask,
+		struct spi_board_info *info, unsigned len)
+{
+	/* for now, assume we need MISO */
+	davinci_cfg_reg(DM355_SPI0_SDI);
+
+	/* not all slaves will be wired up */
+	if (chipselect_mask & BIT(0))
+		davinci_cfg_reg(DM355_SPI0_SDENA0);
+	if (chipselect_mask & BIT(1))
+		davinci_cfg_reg(DM355_SPI0_SDENA1);
+
+	spi_register_board_info(info, len);
+
+	platform_device_register(&dm355_spi0_device);
+}
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Device specific mux setup
+ *
+ *	soc	description	mux  mode   mode  mux	 dbg
+ *				reg  offset mask  mode
+ */
+static const struct mux_config dm355_pins[] = {
+MUX_CFG(DM355,	MMCSD0,		4,   2,     1,	  0,	 false)
+
+MUX_CFG(DM355,	SD1_CLK,	3,   6,     1,	  1,	 false)
+MUX_CFG(DM355,	SD1_CMD,	3,   7,     1,	  1,	 false)
+MUX_CFG(DM355,	SD1_DATA3,	3,   8,     3,	  1,	 false)
+MUX_CFG(DM355,	SD1_DATA2,	3,   10,    3,	  1,	 false)
+MUX_CFG(DM355,	SD1_DATA1,	3,   12,    3,	  1,	 false)
+MUX_CFG(DM355,	SD1_DATA0,	3,   14,    3,	  1,	 false)
+
+MUX_CFG(DM355,	I2C_SDA,	3,   19,    1,	  1,	 false)
+MUX_CFG(DM355,	I2C_SCL,	3,   20,    1,	  1,	 false)
+
+MUX_CFG(DM355,	MCBSP0_BDX,	3,   0,     1,	  1,	 false)
+MUX_CFG(DM355,	MCBSP0_X,	3,   1,     1,	  1,	 false)
+MUX_CFG(DM355,	MCBSP0_BFSX,	3,   2,     1,	  1,	 false)
+MUX_CFG(DM355,	MCBSP0_BDR,	3,   3,     1,	  1,	 false)
+MUX_CFG(DM355,	MCBSP0_R,	3,   4,     1,	  1,	 false)
+MUX_CFG(DM355,	MCBSP0_BFSR,	3,   5,     1,	  1,	 false)
+
+MUX_CFG(DM355,	SPI0_SDI,	4,   1,     1,    0,	 false)
+MUX_CFG(DM355,	SPI0_SDENA0,	4,   0,     1,    0,	 false)
+MUX_CFG(DM355,	SPI0_SDENA1,	3,   28,    1,    1,	 false)
+
+INT_CFG(DM355,  INT_EDMA_CC,	      2,    1,    1,     false)
+INT_CFG(DM355,  INT_EDMA_TC0_ERR,     3,    1,    1,     false)
+INT_CFG(DM355,  INT_EDMA_TC1_ERR,     4,    1,    1,     false)
+
+EVT_CFG(DM355,  EVT8_ASP1_TX,	      0,    1,    0,     false)
+EVT_CFG(DM355,  EVT9_ASP1_RX,	      1,    1,    0,     false)
+EVT_CFG(DM355,  EVT26_MMC0_RX,	      2,    1,    0,     false)
+};
+
+/*----------------------------------------------------------------------*/
+
+static const s8 dma_chan_dm355_no_event[] = {
+	12, 13, 24, 56, 57,
+	58, 59, 60, 61, 62,
+	63,
+	-1
+};
+
+static struct edma_soc_info dm355_edma_info = {
+	.n_channel	= 64,
+	.n_region	= 4,
+	.n_slot		= 128,
+	.n_tc		= 2,
+	.noevent	= dma_chan_dm355_no_event,
+};
+
+static struct resource edma_resources[] = {
+	{
+		.name	= "edma_cc",
+		.start	= 0x01c00000,
+		.end	= 0x01c00000 + SZ_64K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.name	= "edma_tc0",
+		.start	= 0x01c10000,
+		.end	= 0x01c10000 + SZ_1K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.name	= "edma_tc1",
+		.start	= 0x01c10400,
+		.end	= 0x01c10400 + SZ_1K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= IRQ_CCINT0,
+		.flags	= IORESOURCE_IRQ,
+	},
+	{
+		.start	= IRQ_CCERRINT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	/* not using (or muxing) TC*_ERR */
+};
+
+static struct platform_device dm355_edma_device = {
+	.name			= "edma",
+	.id			= -1,
+	.dev.platform_data	= &dm355_edma_info,
+	.num_resources		= ARRAY_SIZE(edma_resources),
+	.resource		= edma_resources,
+};
+
+/*----------------------------------------------------------------------*/
+
+void __init dm355_init(void)
+{
+	davinci_clk_init(dm355_clks);
+	davinci_mux_register(dm355_pins, ARRAY_SIZE(dm355_pins));;
+}
+
+static int __init dm355_init_devices(void)
+{
+	if (!cpu_is_davinci_dm355())
+		return 0;
+
+	davinci_cfg_reg(DM355_INT_EDMA_CC);
+	platform_device_register(&dm355_edma_device);
+	return 0;
+}
+postcore_initcall(dm355_init_devices);

arch/arm/mach-davinci/include/mach/dm355.h

+/*
+ * Chip specific defines for DM355 SoC
+ *
+ * Author: Kevin Hilman, Deep Root Systems, LLC
+ *
+ * 2007 (c) Deep Root Systems, LLC. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#ifndef __ASM_ARCH_DM355_H
+#define __ASM_ARCH_DM355_H
+
+#include <mach/hardware.h>
+
+void __init dm355_init(void);
+
+struct spi_board_info;
+
+void dm355_init_spi0(unsigned chipselect_mask,
+		struct spi_board_info *info, unsigned len);
+
+#endif /* __ASM_ARCH_DM355_H */

arch/arm/mach-davinci/include/mach/serial.h

@@ -18,7 +18,7 @@
 #define DAVINCI_UART1_BASE	(IO_PHYS + 0x20400)
 #define DAVINCI_UART2_BASE	(IO_PHYS + 0x20800)
 
-#define DM355_UART2_BASE	(IO_PHYS + 0x206000)
+#define DM355_UART2_BASE        (IO_PHYS + 0x206000)
 
 /* DaVinci UART register offsets */
 #define UART_DAVINCI_PWREMU		0x0c