pinctrl: tegra: add a driver for Tegra210

Tegra210's pinmux supports a different set of pins/options than earlier
SoCs, so requires its own driver (well, table of pin-specific data).

Cc: devicetree@vger.kernel.org
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-pinmux.txt

+NVIDIA Tegra210 pinmux controller
+
+Required properties:
+- compatible: "nvidia,tegra210-pinmux"
+- reg: Should contain a list of base address and size pairs for:
+  - first entry: The APB_MISC_GP_*_PADCTRL registers (pad control)
+  - second entry: The PINMUX_AUX_* registers (pinmux)
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Tegra's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, tristate, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function or tristate parameter. For this
+reason, even seemingly boolean values are actually tristates in this binding:
+unspecified, off, or on. Unspecified is represented as an absent property,
+and off/on are represented as integer values 0 and 1.
+
+See the TRM to determine which properties and values apply to each pin/group.
+Macro values for property values are defined in
+include/dt-binding/pinctrl/pinctrl-tegra.h.
+
+Required subnode-properties:
+- nvidia,pins : An array of strings. Each string contains the name of a pin or
+    group. Valid values for these names are listed below.
+
+Optional subnode-properties:
+- nvidia,function: A string containing the name of the function to mux to the
+    pin or group.
+- nvidia,pull: Integer, representing the pull-down/up to apply to the pin.
+    0: none, 1: down, 2: up.
+- nvidia,tristate: Integer.
+    0: drive, 1: tristate.
+- nvidia,enable-input: Integer. Enable the pin's input path.
+    enable :TEGRA_PIN_ENABLE0 and
+    disable or output only: TEGRA_PIN_DISABLE.
+- nvidia,open-drain: Integer.
+    enable: TEGRA_PIN_ENABLE.
+    disable: TEGRA_PIN_DISABLE.
+- nvidia,lock: Integer. Lock the pin configuration against further changes
+    until reset.
+    enable: TEGRA_PIN_ENABLE.
+    disable: TEGRA_PIN_DISABLE.
+- nvidia,io-hv: Integer. Select high-voltage receivers.
+    normal: TEGRA_PIN_DISABLE
+    high: TEGRA_PIN_ENABLE
+- nvidia,high-speed-mode: Integer. Enable high speed mode the pins.
+    normal: TEGRA_PIN_DISABLE
+    high: TEGRA_PIN_ENABLE
+- nvidia,schmitt: Integer. Enables Schmitt Trigger on the input.
+    normal: TEGRA_PIN_DISABLE
+    high: TEGRA_PIN_ENABLE
+- nvidia,drive-type: Integer. Valid range 0...3.
+- nvidia,pull-down-strength: Integer. Controls drive strength. 0 is weakest.
+    The range of valid values depends on the pingroup. See "CAL_DRVDN" in the
+    Tegra TRM.
+- nvidia,pull-up-strength: Integer. Controls drive strength. 0 is weakest.
+    The range of valid values depends on the pingroup. See "CAL_DRVUP" in the
+    Tegra TRM.
+- nvidia,slew-rate-rising: Integer. Controls rising signal slew rate. 0 is
+    fastest. The range of valid values depends on the pingroup. See
+    "DRVDN_SLWR" in the Tegra TRM.
+- nvidia,slew-rate-falling: Integer. Controls falling signal slew rate. 0 is
+    fastest. The range of valid values depends on the pingroup. See
+    "DRVUP_SLWF" in the Tegra TRM.
+
+Valid values for pin and group names (nvidia,pin) are:
+
+  Mux groups:
+
+    These correspond to Tegra PINMUX_AUX_* (pinmux) registers. Any property
+    that exists in those registers may be set for the following pin names.
+
+    In Tegra210, many pins also have a dedicated APB_MISC_GP_*_PADCTRL
+    register. Where that is true, and property that exists in that register
+    may also be set on the following pin names.
+
+    als_prox_int_px3, ap_ready_pv5, ap_wake_bt_ph3, ap_wake_nfc_ph7,
+    aud_mclk_pbb0, batt_bcl, bt_rst_ph4, bt_wake_ap_ph5, button_home_py1,
+    button_power_on_px5, button_slide_sw_py0, button_vol_down_px7,
+    button_vol_up_px6, cam1_mclk_ps0, cam1_pwdn_ps7, cam1_strobe_pt1,
+    cam2_mclk_ps1, cam2_pwdn_pt0, cam_af_en_ps5, cam_flash_en_ps6,
+    cam_i2c_scl_ps2, cam_i2c_sda_ps3, cam_rst_ps4cam_rst_ps4, clk_32k_in,
+    clk_32k_out_py5, clk_req, core_pwr_req, cpu_pwr_req, dap1_din_pb1,
+    dap1_dout_pb2, dap1_fs_pb0, dap1_sclk_pb3, dap2_din_paa2, dap2_dout_paa3,
+    dap2_fs_paa0, dap2_sclk_paa1, dap4_din_pj5, dap4_dout_pj6, dap4_fs_pj4,
+    dap4_sclk_pj7, dmic1_clk_pe0, dmic1_dat_pe1, dmic2_clk_pe2, dmic2_dat_pe3,
+    dmic3_clk_pe4, dmic3_dat_pe5, dp_hpd0_pcc6, dvfs_clk_pbb2, dvfs_pwm_pbb1,
+    gen1_i2c_scl_pj1, gen1_i2c_sda_pj0, gen2_i2c_scl_pj2, gen2_i2c_sda_pj3,
+    gen3_i2c_scl_pf0, gen3_i2c_sda_pf1, gpio_x1_aud_pbb3, gpio_x3_aud_pbb4,
+    gps_en_pi2, gps_rst_pi3, hdmi_cec_pcc0, hdmi_int_dp_hpd_pcc1, jtag_rtck,
+    lcd_bl_en_pv1, lcd_bl_pwm_pv0, lcd_gpio1_pv3, lcd_gpio2_pv4, lcd_rst_pv2,
+    lcd_te_py2, modem_wake_ap_px0, motion_int_px2, nfc_en_pi0, nfc_int_pi1,
+    pa6, pcc7, pe6, pe7, pex_l0_clkreq_n_pa1, pex_l0_rst_n_pa0,
+    pex_l1_clkreq_n_pa4, pex_l1_rst_n_pa3, pex_wake_n_pa2, ph6, pk0, pk1, pk2,
+    pk3, pk4, pk5, pk6, pk7, pl0, pl1, pwr_i2c_scl_py3, pwr_i2c_sda_py4,
+    pwr_int_n, pz0, pz1, pz2, pz3, pz4, pz5, qspi_cs_n_pee1, qspi_io0_pee2,
+    qspi_io1_pee3, qspi_io2_pee4, qspi_io3_pee5, qspi_sck_pee0,
+    sata_led_active_pa5, sdmmc1_clk_pm0, sdmmc1_cmd_pm1, sdmmc1_dat0_pm5,
+    sdmmc1_dat1_pm4, sdmmc1_dat2_pm3, sdmmc1_dat3_pm2, sdmmc3_clk_pp0,
+    sdmmc3_cmd_pp1, sdmmc3_dat0_pp5, sdmmc3_dat1_pp4, sdmmc3_dat2_pp3,
+    sdmmc3_dat3_pp2, shutdown, spdif_in_pcc3, spdif_out_pcc2, spi1_cs0_pc3,
+    spi1_cs1_pc4, spi1_miso_pc1, spi1_mosi_pc0, spi1_sck_pc2, spi2_cs0_pb7,
+    spi2_cs1_pdd0, spi2_miso_pb5, spi2_mosi_pb4, spi2_sck_pb6, spi4_cs0_pc6,
+    spi4_miso_pd0, spi4_mosi_pc7, spi4_sck_pc5, temp_alert_px4, touch_clk_pv7,
+    touch_int_px1, touch_rst_pv6, uart1_cts_pu3, uart1_rts_pu2, uart1_rx_pu1,
+    uart1_tx_pu0, uart2_cts_pg3, uart2_rts_pg2, uart2_rx_pg1, uart2_tx_pg0,
+    uart3_cts_pd4, uart3_rts_pd3, uart3_rx_pd2, uart3_tx_pd1, uart4_cts_pi7,
+    uart4_rts_pi6, uart4_rx_pi5, uart4_tx_pi4, usb_vbus_en0_pcc4,
+    usb_vbus_en1_pcc5, wifi_en_ph0, wifi_rst_ph1, wifi_wake_ap_ph2
+
+  Drive groups:
+
+    These correspond to the Tegra APB_MISC_GP_*_PADCTRL (pad control)
+    registers. Note that where one of these registers controls a single pin
+    for which a PINMUX_AUX_* exists, see the list above for the pin name to
+    use when configuring the pinmux.
+
+    pa6, pcc7, pe6, pe7, ph6, pk0, pk1, pk2, pk3, pk4, pk5, pk6, pk7, pl0, pl1,
+    pz0, pz1, pz2, pz3, pz4, pz5, sdmmc1, sdmmc2, sdmmc3, sdmmc4
+
+Valid values for nvidia,functions are:
+
+    aud, bcl, blink, ccla, cec, cldvfs, clk, core, cpu, displaya, displayb,
+    dmic1, dmic2, dmic3, dp, dtv, extperiph3, i2c1, i2c2, i2c3, i2cpmu, i2cvi,
+    i2s1, i2s2, i2s3, i2s4a, i2s4b, i2s5a, i2s5b, iqc0, iqc1, jtag, pe, pe0,
+    pe1, pmi, pwm0, pwm1, pwm2, pwm3, qspi, rsvd0, rsvd1, rsvd2, rsvd3, sata,
+    sdmmc1, sdmmc3, shutdown, soc, sor0, sor1, spdif, spi1, spi2, spi3, spi4,
+    sys, touch, uart, uarta, uartb, uartc, uartd, usb, vgp1, vgp2, vgp3, vgp4,
+    vgp5, vgp6, vimclk, vimclk2
+
+Example:
+
+	pinmux: pinmux@70000800 {
+		compatible = "nvidia,tegra210-pinmux";
+		reg = <0x0 0x700008d4 0x0 0x2a8>, /* Pad control registers */
+		      <0x0 0x70003000 0x0 0x1000>; /* Mux registers */
+
+		pinctrl-names = "boot";
+		pinctrl-0 = <&state_boot>;
+
+		state_boot: pinmux {
+			gen1_i2c_scl_pj1 {
+				nvidia,pins = "gen1_i2c_scl_pj1",
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,io-hv = <TEGRA_PIN_ENABLE>;
+			};
+		};
+	};
+};

drivers/pinctrl/Kconfig

@@ -154,6 +154,10 @@ config PINCTRL_TEGRA124
 	bool
 	select PINCTRL_TEGRA
 
+config PINCTRL_TEGRA210
+	bool
+	select PINCTRL_TEGRA
+
 config PINCTRL_TEGRA_XUSB
 	def_bool y if ARCH_TEGRA
 	select GENERIC_PHY

drivers/pinctrl/Makefile

@@ -27,6 +27,7 @@ obj-$(CONFIG_PINCTRL_TEGRA20)	+= pinctrl-tegra20.o
 obj-$(CONFIG_PINCTRL_TEGRA30)	+= pinctrl-tegra30.o
 obj-$(CONFIG_PINCTRL_TEGRA114)	+= pinctrl-tegra114.o
 obj-$(CONFIG_PINCTRL_TEGRA124)	+= pinctrl-tegra124.o
+obj-$(CONFIG_PINCTRL_TEGRA210)	+= pinctrl-tegra210.o
 obj-$(CONFIG_PINCTRL_TEGRA_XUSB)	+= pinctrl-tegra-xusb.o
 obj-$(CONFIG_PINCTRL_TZ1090)	+= pinctrl-tz1090.o
 obj-$(CONFIG_PINCTRL_TZ1090_PDC)	+= pinctrl-tz1090-pdc.o