Merge 3.5-rc4 into usb-linus

This is needed to sync up with the previous USB changes that were merged in
Linus's branch.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

.mailmap

@@ -111,6 +111,7 @@ Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
 Uwe Kleine-König <ukl@pengutronix.de>
 Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
 Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
+Viresh Kumar <viresh.linux@gmail.com> <viresh.kumar@st.com>
 Takashi YOSHII <takashi.yoshii.zj@renesas.com>
 Yusuke Goda <goda.yusuke@renesas.com>
 Gustavo Padovan <gustavo@las.ic.unicamp.br>

Documentation/ABI/testing/sysfs-bus-iio

@@ -219,6 +219,7 @@ What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltage_scale
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltageY_scale
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_accel_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_accel_peak_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_anglvel_scale
@@ -273,6 +274,7 @@ What:		/sys/bus/iio/devices/iio:deviceX/in_accel_scale_available
 What:		/sys/.../iio:deviceX/in_voltageX_scale_available
 What:		/sys/.../iio:deviceX/in_voltage-voltage_scale_available
 What:		/sys/.../iio:deviceX/out_voltageX_scale_available
+What:		/sys/.../iio:deviceX/out_altvoltageX_scale_available
 What:		/sys/.../iio:deviceX/in_capacitance_scale_available
 KernelVersion:	2.635
 Contact:	linux-iio@vger.kernel.org
@@ -298,14 +300,19 @@ Description:
 		gives the 3dB frequency of the filter in Hz.
 
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltageY_raw
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY_raw
 KernelVersion:	2.6.37
 Contact:	linux-iio@vger.kernel.org
 Description:
 		Raw (unscaled, no bias etc.) output voltage for
 		channel Y.  The number must always be specified and
 		unique if the output corresponds to a single channel.
+		While DAC like devices typically use out_voltage,
+		a continuous frequency generating device, such as
+		a DDS or PLL should use out_altvoltage.
 
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltageY&Z_raw
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY&Z_raw
 KernelVersion:	2.6.37
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -316,6 +323,8 @@ Description:
 
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltageY_powerdown_mode
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltage_powerdown_mode
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY_powerdown_mode
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltage_powerdown_mode
 KernelVersion:	2.6.38
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -330,6 +339,8 @@ Description:
 
 What:		/sys/.../iio:deviceX/out_votlageY_powerdown_mode_available
 What:		/sys/.../iio:deviceX/out_voltage_powerdown_mode_available
+What:		/sys/.../iio:deviceX/out_altvotlageY_powerdown_mode_available
+What:		/sys/.../iio:deviceX/out_altvoltage_powerdown_mode_available
 KernelVersion:	2.6.38
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -338,6 +349,8 @@ Description:
 
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltageY_powerdown
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltage_powerdown
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY_powerdown
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltage_powerdown
 KernelVersion:	2.6.38
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -346,6 +359,24 @@ Description:
 		normal operation. Y may be suppressed if all outputs are
 		controlled together.
 
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY_frequency
+KernelVersion:	3.4.0
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Output frequency for channel Y in Hz. The number must always be
+		specified and unique if the output corresponds to a single
+		channel.
+
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY_phase
+KernelVersion:	3.4.0
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Phase in radians of one frequency/clock output Y
+		(out_altvoltageY) relative to another frequency/clock output
+		(out_altvoltageZ) of the device X. The number must always be
+		specified and unique if the output corresponds to a single
+		channel.
+
 What:		/sys/bus/iio/devices/iio:deviceX/events
 KernelVersion:	2.6.35
 Contact:	linux-iio@vger.kernel.org

Documentation/arm/SPEAr/overview.txt

@@ -60,4 +60,4 @@ Introduction
   Document Author
   ---------------
 
-  Viresh Kumar <viresh.kumar@st.com>, (c) 2010-2012 ST Microelectronics
+  Viresh Kumar <viresh.linux@gmail.com>, (c) 2010-2012 ST Microelectronics

Documentation/hwmon/coretemp

@@ -6,7 +6,9 @@ Supported chips:
     Prefix: 'coretemp'
     CPUID: family 0x6, models 0xe (Pentium M DC), 0xf (Core 2 DC 65nm),
                               0x16 (Core 2 SC 65nm), 0x17 (Penryn 45nm),
-                              0x1a (Nehalem), 0x1c (Atom), 0x1e (Lynnfield)
+                              0x1a (Nehalem), 0x1c (Atom), 0x1e (Lynnfield),
+                              0x26 (Tunnel Creek Atom), 0x27 (Medfield Atom),
+                              0x36 (Cedar Trail Atom)
     Datasheet: Intel 64 and IA-32 Architectures Software Developer's Manual
                Volume 3A: System Programming Guide
                http://softwarecommunity.intel.com/Wiki/Mobility/720.htm
@@ -52,6 +54,17 @@ Some information comes from ark.intel.com
 
 Process		Processor					TjMax(C)
 
+22nm		Core i5/i7 Processors
+		i7 3920XM, 3820QM, 3720QM, 3667U, 3520M		105
+		i5 3427U, 3360M/3320M				105
+		i7 3770/3770K					105
+		i5 3570/3570K, 3550, 3470/3450			105
+		i7 3770S					103
+		i5 3570S/3550S, 3475S/3470S/3450S		103
+		i7 3770T					94
+		i5 3570T					94
+		i5 3470T					91
+
 32nm		Core i3/i5/i7 Processors
 		i7 660UM/640/620, 640LM/620, 620M, 610E		105
 		i5 540UM/520/430, 540M/520/450/430		105
@@ -65,6 +78,11 @@ Process		Processor					TjMax(C)
 		U3400						105
 		P4505/P4500 					90
 
+32nm		Atom Processors
+		Z2460						90
+		D2700/2550/2500					100
+		N2850/2800/2650/2600				100
+
 45nm		Xeon Processors 5400 Quad-Core
 		X5492, X5482, X5472, X5470, X5460, X5450	85
 		E5472, E5462, E5450/40/30/20/10/05		85
@@ -85,6 +103,8 @@ Process		Processor					TjMax(C)
 		N475/470/455/450				100
 		N280/270					90
 		330/230						125
+		E680/660/640/620				90
+		E680T/660T/640T/620T				110
 
 45nm		Core2 Processors
 		Solo ULV SU3500/3300				100

MAINTAINERS

@@ -579,7 +579,7 @@ F:	drivers/net/appletalk/
 F:	net/appletalk/
 
 ARASAN COMPACT FLASH PATA CONTROLLER
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 L:	linux-ide@vger.kernel.org
 S:	Maintained
 F:	include/linux/pata_arasan_cf_data.h
@@ -5296,7 +5296,7 @@ S:	Maintained
 F:	drivers/pinctrl/
 
 PIN CONTROLLER - ST SPEAR
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 W:	http://www.st.com/spear
@@ -5873,7 +5873,7 @@ S:	Maintained
 F:	drivers/tty/serial
 
 SYNOPSYS DESIGNWARE DMAC DRIVER
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 S:	Maintained
 F:	include/linux/dw_dmac.h
 F:	drivers/dma/dw_dmac_regs.h
@@ -6021,7 +6021,7 @@ S:	Maintained
 F:	drivers/mmc/host/sdhci-s3c.c
 
 SECURE DIGITAL HOST CONTROLLER INTERFACE (SDHCI) ST SPEAR DRIVER
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 L:	spear-devel@list.st.com
 L:	linux-mmc@vger.kernel.org
 S:	Maintained
@@ -6377,7 +6377,7 @@ S:	Maintained
 F:	include/linux/compiler.h
 
 SPEAR PLATFORM SUPPORT
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 M:	Shiraz Hashim <shiraz.hashim@st.com>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -6386,7 +6386,7 @@ S:	Maintained
 F:	arch/arm/plat-spear/
 
 SPEAR13XX MACHINE SUPPORT
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 M:	Shiraz Hashim <shiraz.hashim@st.com>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -6395,7 +6395,7 @@ S:	Maintained
 F:	arch/arm/mach-spear13xx/
 
 SPEAR3XX MACHINE SUPPORT
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 M:	Shiraz Hashim <shiraz.hashim@st.com>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -6406,7 +6406,7 @@ F:	arch/arm/mach-spear3xx/
 SPEAR6XX MACHINE SUPPORT
 M:	Rajeev Kumar <rajeev-dlh.kumar@st.com>
 M:	Shiraz Hashim <shiraz.hashim@st.com>
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 W:	http://www.st.com/spear
@@ -6414,7 +6414,7 @@ S:	Maintained
 F:	arch/arm/mach-spear6xx/
 
 SPEAR CLOCK FRAMEWORK SUPPORT
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 W:	http://www.st.com/spear
@@ -7421,7 +7421,7 @@ F:	include/linux/vlynq.h
 
 VME SUBSYSTEM
 M:	Martyn Welch <martyn.welch@ge.com>
-M:	Manohar Vanga <manohar.vanga@cern.ch>
+M:	Manohar Vanga <manohar.vanga@gmail.com>
 M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 L:	devel@driverdev.osuosl.org
 S:	Maintained

Makefile

 VERSION = 3
 PATCHLEVEL = 5
 SUBLEVEL = 0
-EXTRAVERSION = -rc3
+EXTRAVERSION = -rc4
 NAME = Saber-toothed Squirrel
 
 # *DOCUMENTATION*
@@ -561,6 +561,8 @@ else
 KBUILD_CFLAGS	+= -O2
 endif
 
+include $(srctree)/arch/$(SRCARCH)/Makefile
+
 ifdef CONFIG_READABLE_ASM
 # Disable optimizations that make assembler listings hard to read.
 # reorder blocks reorders the control in the function
@@ -571,8 +573,6 @@ KBUILD_CFLAGS += $(call cc-option,-fno-reorder-blocks,) \
                  $(call cc-option,-fno-partial-inlining)
 endif
 
-include $(srctree)/arch/$(SRCARCH)/Makefile
-
 ifneq ($(CONFIG_FRAME_WARN),0)
 KBUILD_CFLAGS += $(call cc-option,-Wframe-larger-than=${CONFIG_FRAME_WARN})
 endif

arch/arm/Kconfig

@@ -293,6 +293,7 @@ config ARCH_VERSATILE
 	select ICST
 	select GENERIC_CLOCKEVENTS
 	select ARCH_WANT_OPTIONAL_GPIOLIB
+	select NEED_MACH_IO_H if PCI
 	select PLAT_VERSATILE
 	select PLAT_VERSATILE_CLCD
 	select PLAT_VERSATILE_FPGA_IRQ
@@ -588,6 +589,7 @@ config ARCH_ORION5X
 	select PCI
 	select ARCH_REQUIRE_GPIOLIB
 	select GENERIC_CLOCKEVENTS
+	select NEED_MACH_IO_H
 	select PLAT_ORION
 	help
 	  Support for the following Marvell Orion 5x series SoCs:

arch/arm/boot/dts/mmp2-brownstone.dts

@@ -11,7 +11,7 @@
 /include/ "mmp2.dtsi"
 
 / {
-	model = "Marvell MMP2 Aspenite Development Board";
+	model = "Marvell MMP2 Brownstone Development Board";
 	compatible = "mrvl,mmp2-brownstone", "mrvl,mmp2";
 
 	chosen {
@@ -19,7 +19,7 @@
 	};
 
 	memory {
-		reg = <0x00000000 0x04000000>;
+		reg = <0x00000000 0x08000000>;
 	};
 
 	soc {

arch/arm/boot/dts/omap2.dtsi

@@ -44,6 +44,8 @@
 			compatible = "ti,omap2-intc";
 			interrupt-controller;
 			#interrupt-cells = <1>;
+			ti,intc-size = <96>;
+			reg = <0x480FE000 0x1000>;
 		};
 
 		uart1: serial@4806a000 {

arch/arm/boot/dts/spear1310-evb.dts

 /*
  * DTS file for SPEAr1310 Evaluation Baord
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear1310.dtsi

 /*
  * DTS file for all SPEAr1310 SoCs
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear1340-evb.dts

 /*
  * DTS file for SPEAr1340 Evaluation Baord
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear1340.dtsi

 /*
  * DTS file for all SPEAr1340 SoCs
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear13xx.dtsi

 /*
  * DTS file for all SPEAr13xx SoCs
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear300-evb.dts

 /*
  * DTS file for SPEAr300 Evaluation Baord
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear300.dtsi

 /*
  * DTS file for SPEAr300 SoC
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear310-evb.dts

 /*
  * DTS file for SPEAr310 Evaluation Baord
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear310.dtsi

 /*
  * DTS file for SPEAr310 SoC
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear320-evb.dts

 /*
  * DTS file for SPEAr320 Evaluation Baord
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear320.dtsi

 /*
  * DTS file for SPEAr320 SoC
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear3xx.dtsi

 /*
  * DTS file for all SPEAr3xx SoCs
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/include/asm/futex.h

@@ -19,6 +19,7 @@
 	"	.long	1b, 4f, 2b, 4f\n"			\
 	"	.popsection\n"					\
 	"	.pushsection .fixup,\"ax\"\n"			\
+	"	.align	2\n"					\
 	"4:	mov	%0, " err_reg "\n"			\
 	"	b	3b\n"					\
 	"	.popsection"

arch/arm/include/asm/hardware/sp810.h

@@ -4,7 +4,7 @@
  * ARM PrimeXsys System Controller SP810 header file
  *
  * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/kernel/entry-armv.S

@@ -495,6 +495,7 @@ ENDPROC(__und_usr)
  * The out of line fixup for the ldrt above.
  */
 	.pushsection .fixup, "ax"
+	.align	2
 4:	mov	pc, r9
 	.popsection
 	.pushsection __ex_table,"a"

arch/arm/kernel/kprobes-thumb.c

@@ -660,7 +660,7 @@ static const union decode_item t32_table_1111_100x[] = {
 	/* LDRSB (literal)	1111 1001 x001 1111 xxxx xxxx xxxx xxxx */
 	/* LDRH (literal)	1111 1000 x011 1111 xxxx xxxx xxxx xxxx */
 	/* LDRSH (literal)	1111 1001 x011 1111 xxxx xxxx xxxx xxxx */
-	DECODE_EMULATEX	(0xfe5f0000, 0xf81f0000, t32_simulate_ldr_literal,
+	DECODE_SIMULATEX(0xfe5f0000, 0xf81f0000, t32_simulate_ldr_literal,
 						 REGS(PC, NOSPPCX, 0, 0, 0)),
 
 	/* STRB (immediate)	1111 1000 0000 xxxx xxxx 1xxx xxxx xxxx */

arch/arm/mach-highbank/Makefile

-obj-y					:= clock.o highbank.o system.o
+obj-y					:= clock.o highbank.o system.o smc.o
+
+plus_sec := $(call as-instr,.arch_extension sec,+sec)
+AFLAGS_smc.o				:=-Wa,-march=armv7-a$(plus_sec)
+
 obj-$(CONFIG_DEBUG_HIGHBANK_UART)	+= lluart.o
 obj-$(CONFIG_SMP)			+= platsmp.o
 obj-$(CONFIG_HOTPLUG_CPU)		+= hotplug.o

arch/arm/mach-highbank/core.h

@@ -8,3 +8,4 @@ extern void highbank_lluart_map_io(void);
 static inline void highbank_lluart_map_io(void) {}
 #endif
 
+extern void highbank_smc1(int fn, int arg);

arch/arm/mach-highbank/highbank.c

@@ -85,10 +85,24 @@ const static struct of_device_id irq_match[] = {
 	{}
 };
 
+#ifdef CONFIG_CACHE_L2X0
+static void highbank_l2x0_disable(void)
+{
+	/* Disable PL310 L2 Cache controller */
+	highbank_smc1(0x102, 0x0);
+}
+#endif
+
 static void __init highbank_init_irq(void)
 {
 	of_irq_init(irq_match);
+
+#ifdef CONFIG_CACHE_L2X0
+	/* Enable PL310 L2 Cache controller */
+	highbank_smc1(0x102, 0x1);
 	l2x0_of_init(0, ~0UL);
+	outer_cache.disable = highbank_l2x0_disable;
+#endif
 }
 
 static void __init highbank_timer_init(void)

arch/arm/mach-highbank/smc.S

+/*
+ * Copied from omap44xx-smc.S Copyright (C) 2010 Texas Instruments, Inc.
+ * Copyright 2012 Calxeda, Inc.
+ *
+ * This program is free software,you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/linkage.h>
+
+/*
+ * This is common routine to manage secure monitor API
+ * used to modify the PL310 secure registers.
+ * 'r0' contains the value to be modified and 'r12' contains
+ * the monitor API number.
+ * Function signature : void highbank_smc1(u32 fn, u32 arg)
+ */
+
+ENTRY(highbank_smc1)
+	stmfd   sp!, {r4-r11, lr}
+	mov	r12, r0
+	mov 	r0, r1
+	dsb
+	smc	#0
+	ldmfd   sp!, {r4-r11, pc}
+ENDPROC(highbank_smc1)

arch/arm/mach-imx/Kconfig

@@ -477,6 +477,7 @@ config MACH_MX31_3DS
 	select IMX_HAVE_PLATFORM_IMX2_WDT
 	select IMX_HAVE_PLATFORM_IMX_I2C
 	select IMX_HAVE_PLATFORM_IMX_KEYPAD
+	select IMX_HAVE_PLATFORM_IMX_SSI
 	select IMX_HAVE_PLATFORM_IMX_UART
 	select IMX_HAVE_PLATFORM_IPU_CORE
 	select IMX_HAVE_PLATFORM_MXC_EHCI

arch/arm/mach-imx/clk-imx1.c

@@ -108,8 +108,7 @@ int __init mx1_clocks_init(unsigned long fref)
 	clk_register_clkdev(clk[clk32], NULL, "mxc_rtc.0");
 	clk_register_clkdev(clk[clko], "clko", NULL);
 
-	mxc_timer_init(NULL, MX1_IO_ADDRESS(MX1_TIM1_BASE_ADDR),
-			MX1_TIM1_INT);
+	mxc_timer_init(MX1_IO_ADDRESS(MX1_TIM1_BASE_ADDR), MX1_TIM1_INT);
 
 	return 0;
 }

arch/arm/mach-imx/clk-imx21.c

@@ -180,7 +180,7 @@ int __init mx21_clocks_init(unsigned long lref, unsigned long href)
 	clk_register_clkdev(clk[sdhc1_ipg_gate], "sdhc1", NULL);
 	clk_register_clkdev(clk[sdhc2_ipg_gate], "sdhc2", NULL);
 
-	mxc_timer_init(NULL, MX21_IO_ADDRESS(MX21_GPT1_BASE_ADDR),
-			MX21_INT_GPT1);
+	mxc_timer_init(MX21_IO_ADDRESS(MX21_GPT1_BASE_ADDR), MX21_INT_GPT1);
+
 	return 0;
 }

arch/arm/mach-imx/clk-imx25.c

@@ -243,6 +243,6 @@ int __init mx25_clocks_init(void)
 	clk_register_clkdev(clk[sdma_ahb], "ahb", "imx35-sdma");
 	clk_register_clkdev(clk[iim_ipg], "iim", NULL);
 
-	mxc_timer_init(NULL, MX25_IO_ADDRESS(MX25_GPT1_BASE_ADDR), 54);
+	mxc_timer_init(MX25_IO_ADDRESS(MX25_GPT1_BASE_ADDR), 54);
 	return 0;
 }

arch/arm/mach-imx/clk-imx27.c

@@ -263,8 +263,7 @@ int __init mx27_clocks_init(unsigned long fref)
 	clk_register_clkdev(clk[ssi1_baud_gate], "bitrate" , "imx-ssi.0");
 	clk_register_clkdev(clk[ssi2_baud_gate], "bitrate" , "imx-ssi.1");
 
-	mxc_timer_init(NULL, MX27_IO_ADDRESS(MX27_GPT1_BASE_ADDR),
-			MX27_INT_GPT1);
+	mxc_timer_init(MX27_IO_ADDRESS(MX27_GPT1_BASE_ADDR), MX27_INT_GPT1);
 
 	clk_prepare_enable(clk[emi_ahb_gate]);
 

arch/arm/mach-imx/clk-imx31.c

@@ -175,8 +175,7 @@ int __init mx31_clocks_init(unsigned long fref)
 	mx31_revision();
 	clk_disable_unprepare(clk[iim_gate]);
 
-	mxc_timer_init(NULL, MX31_IO_ADDRESS(MX31_GPT1_BASE_ADDR),
-			MX31_INT_GPT);
+	mxc_timer_init(MX31_IO_ADDRESS(MX31_GPT1_BASE_ADDR), MX31_INT_GPT);
 
 	return 0;
 }

arch/arm/mach-imx/clk-imx35.c

@@ -267,11 +267,9 @@ int __init mx35_clocks_init()
 	imx_print_silicon_rev("i.MX35", mx35_revision());
 
 #ifdef CONFIG_MXC_USE_EPIT
-	epit_timer_init(&epit1_clk,
-			MX35_IO_ADDRESS(MX35_EPIT1_BASE_ADDR), MX35_INT_EPIT1);
+	epit_timer_init(MX35_IO_ADDRESS(MX35_EPIT1_BASE_ADDR), MX35_INT_EPIT1);
 #else
-	mxc_timer_init(NULL, MX35_IO_ADDRESS(MX35_GPT1_BASE_ADDR),
-			MX35_INT_GPT);
+	mxc_timer_init(MX35_IO_ADDRESS(MX35_GPT1_BASE_ADDR), MX35_INT_GPT);
 #endif
 
 	return 0;

arch/arm/mach-imx/clk-imx51-imx53.c

@@ -104,12 +104,12 @@ static void __init mx5_clocks_common_init(unsigned long rate_ckil,
 				periph_apm_sel, ARRAY_SIZE(periph_apm_sel));
 	clk[main_bus] = imx_clk_mux("main_bus", MXC_CCM_CBCDR, 25, 1,
 				main_bus_sel, ARRAY_SIZE(main_bus_sel));
-	clk[per_lp_apm] = imx_clk_mux("per_lp_apm", MXC_CCM_CBCDR, 1, 1,
+	clk[per_lp_apm] = imx_clk_mux("per_lp_apm", MXC_CCM_CBCMR, 1, 1,
 				per_lp_apm_sel, ARRAY_SIZE(per_lp_apm_sel));
 	clk[per_pred1] = imx_clk_divider("per_pred1", "per_lp_apm", MXC_CCM_CBCDR, 6, 2);
 	clk[per_pred2] = imx_clk_divider("per_pred2", "per_pred1", MXC_CCM_CBCDR, 3, 3);
 	clk[per_podf] = imx_clk_divider("per_podf", "per_pred2", MXC_CCM_CBCDR, 0, 3);
-	clk[per_root] = imx_clk_mux("per_root", MXC_CCM_CBCDR, 1, 0,
+	clk[per_root] = imx_clk_mux("per_root", MXC_CCM_CBCMR, 0, 1,
 				per_root_sel, ARRAY_SIZE(per_root_sel));
 	clk[ahb] = imx_clk_divider("ahb", "main_bus", MXC_CCM_CBCDR, 10, 3);
 	clk[ahb_max] = imx_clk_gate2("ahb_max", "ahb", MXC_CCM_CCGR0, 28);
@@ -172,7 +172,7 @@ static void __init mx5_clocks_common_init(unsigned long rate_ckil,
 	clk[pwm1_hf_gate] = imx_clk_gate2("pwm1_hf_gate", "ipg", MXC_CCM_CCGR2, 12);
 	clk[pwm2_ipg_gate] = imx_clk_gate2("pwm2_ipg_gate", "ipg", MXC_CCM_CCGR2, 14);
 	clk[pwm2_hf_gate] = imx_clk_gate2("pwm2_hf_gate", "ipg", MXC_CCM_CCGR2, 16);
-	clk[gpt_gate] = imx_clk_gate2("gpt_gate", "ipg", MXC_CCM_CCGR2, 18);
+	clk[gpt_gate] = imx_clk_gate2("gpt_gate", "per_root", MXC_CCM_CCGR2, 18);
 	clk[fec_gate] = imx_clk_gate2("fec_gate", "ipg", MXC_CCM_CCGR2, 24);
 	clk[usboh3_gate] = imx_clk_gate2("usboh3_gate", "ipg", MXC_CCM_CCGR2, 26);
 	clk[usboh3_per_gate] = imx_clk_gate2("usboh3_per_gate", "usboh3_podf", MXC_CCM_CCGR2, 28);
@@ -366,8 +366,7 @@ int __init mx51_clocks_init(unsigned long rate_ckil, unsigned long rate_osc,
 	clk_set_rate(clk[esdhc_b_podf], 166250000);
 
 	/* System timer */
-	mxc_timer_init(NULL, MX51_IO_ADDRESS(MX51_GPT1_BASE_ADDR),
-		MX51_INT_GPT);
+	mxc_timer_init(MX51_IO_ADDRESS(MX51_GPT1_BASE_ADDR), MX51_INT_GPT);
 
 	clk_prepare_enable(clk[iim_gate]);
 	imx_print_silicon_rev("i.MX51", mx51_revision());
@@ -452,8 +451,7 @@ int __init mx53_clocks_init(unsigned long rate_ckil, unsigned long rate_osc,
 	clk_set_rate(clk[esdhc_b_podf], 200000000);
 
 	/* System timer */
-	mxc_timer_init(NULL, MX53_IO_ADDRESS(MX53_GPT1_BASE_ADDR),
-		MX53_INT_GPT);
+	mxc_timer_init(MX53_IO_ADDRESS(MX53_GPT1_BASE_ADDR), MX53_INT_GPT);
 
 	clk_prepare_enable(clk[iim_gate]);
 	imx_print_silicon_rev("i.MX53", mx53_revision());

arch/arm/mach-imx/clk-imx6q.c

@@ -122,10 +122,6 @@ static const char *cko1_sels[]	= { "pll3_usb_otg", "pll2_bus", "pll1_sys", "pll5
 				    "dummy", "axi", "enfc", "ipu1_di0", "ipu1_di1", "ipu2_di0",
 				    "ipu2_di1", "ahb", "ipg", "ipg_per", "ckil", "pll4_audio", };
 
-static const char * const clks_init_on[] __initconst = {
-	"mmdc_ch0_axi", "mmdc_ch1_axi", "usboh3",
-};
-
 enum mx6q_clks {
 	dummy, ckil, ckih, osc, pll2_pfd0_352m, pll2_pfd1_594m, pll2_pfd2_396m,
 	pll3_pfd0_720m, pll3_pfd1_540m, pll3_pfd2_508m, pll3_pfd3_454m,
@@ -161,11 +157,14 @@ enum mx6q_clks {
 
 static struct clk *clk[clk_max];
 
+static enum mx6q_clks const clks_init_on[] __initconst = {
+	mmdc_ch0_axi, mmdc_ch1_axi,
+};
+
 int __init mx6q_clocks_init(void)
 {
 	struct device_node *np;
 	void __iomem *base;
-	struct clk *c;
 	int i, irq;
 
 	clk[dummy] = imx_clk_fixed("dummy", 0);
@@ -424,21 +423,14 @@ int __init mx6q_clocks_init(void)
 	clk_register_clkdev(clk[ahb], "ahb", NULL);
 	clk_register_clkdev(clk[cko1], "cko1", NULL);
 
-	for (i = 0; i < ARRAY_SIZE(clks_init_on); i++) {
-		c = clk_get_sys(clks_init_on[i], NULL);
-		if (IS_ERR(c)) {
-			pr_err("%s: failed to get clk %s", __func__,
-			       clks_init_on[i]);
-			return PTR_ERR(c);
-		}
-		clk_prepare_enable(c);
-	}
+	for (i = 0; i < ARRAY_SIZE(clks_init_on); i++)
+		clk_prepare_enable(clk[clks_init_on[i]]);
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-gpt");
 	base = of_iomap(np, 0);
 	WARN_ON(!base);
 	irq = irq_of_parse_and_map(np, 0);
-	mxc_timer_init(NULL, base, irq);
+	mxc_timer_init(base, irq);
 
 	return 0;
 }

arch/arm/mach-imx/clk-pllv2.c

@@ -74,30 +74,15 @@ struct clk_pllv2 {
 	void __iomem	*base;
 };
 
-static unsigned long clk_pllv2_recalc_rate(struct clk_hw *hw,
-		unsigned long parent_rate)
+static unsigned long __clk_pllv2_recalc_rate(unsigned long parent_rate,
+		u32 dp_ctl, u32 dp_op, u32 dp_mfd, u32 dp_mfn)
 {
 	long mfi, mfn, mfd, pdf, ref_clk, mfn_abs;
-	unsigned long dp_op, dp_mfd, dp_mfn, dp_ctl, pll_hfsm, dbl;
-	void __iomem *pllbase;
+	unsigned long dbl;
 	s64 temp;
-	struct clk_pllv2 *pll = to_clk_pllv2(hw);
-
-	pllbase = pll->base;
 
-	dp_ctl = __raw_readl(pllbase + MXC_PLL_DP_CTL);
-	pll_hfsm = dp_ctl & MXC_PLL_DP_CTL_HFSM;
 	dbl = dp_ctl & MXC_PLL_DP_CTL_DPDCK0_2_EN;
 
-	if (pll_hfsm == 0) {
-		dp_op = __raw_readl(pllbase + MXC_PLL_DP_OP);
-		dp_mfd = __raw_readl(pllbase + MXC_PLL_DP_MFD);
-		dp_mfn = __raw_readl(pllbase + MXC_PLL_DP_MFN);
-	} else {
-		dp_op = __raw_readl(pllbase + MXC_PLL_DP_HFS_OP);
-		dp_mfd = __raw_readl(pllbase + MXC_PLL_DP_HFS_MFD);
-		dp_mfn = __raw_readl(pllbase + MXC_PLL_DP_HFS_MFN);
-	}
 	pdf = dp_op & MXC_PLL_DP_OP_PDF_MASK;
 	mfi = (dp_op & MXC_PLL_DP_OP_MFI_MASK) >> MXC_PLL_DP_OP_MFI_OFFSET;
 	mfi = (mfi <= 5) ? 5 : mfi;
@@ -123,18 +108,30 @@ static unsigned long clk_pllv2_recalc_rate(struct clk_hw *hw,
 	return temp;
 }
 
-static int clk_pllv2_set_rate(struct clk_hw *hw, unsigned long rate,
+static unsigned long clk_pllv2_recalc_rate(struct clk_hw *hw,
 		unsigned long parent_rate)
 {
+	u32 dp_op, dp_mfd, dp_mfn, dp_ctl;
+	void __iomem *pllbase;
 	struct clk_pllv2 *pll = to_clk_pllv2(hw);
+
+	pllbase = pll->base;
+
+	dp_ctl = __raw_readl(pllbase + MXC_PLL_DP_CTL);
+	dp_op = __raw_readl(pllbase + MXC_PLL_DP_OP);
+	dp_mfd = __raw_readl(pllbase + MXC_PLL_DP_MFD);
+	dp_mfn = __raw_readl(pllbase + MXC_PLL_DP_MFN);
+
+	return __clk_pllv2_recalc_rate(parent_rate, dp_ctl, dp_op, dp_mfd, dp_mfn);
+}
+
+static int __clk_pllv2_set_rate(unsigned long rate, unsigned long parent_rate,
+		u32 *dp_op, u32 *dp_mfd, u32 *dp_mfn)
+{
 	u32 reg;
-	void __iomem *pllbase;
 	long mfi, pdf, mfn, mfd = 999999;
 	s64 temp64;
 	unsigned long quad_parent_rate;
-	unsigned long pll_hfsm, dp_ctl;
-
-	pllbase = pll->base;
 
 	quad_parent_rate = 4 * parent_rate;
 	pdf = mfi = -1;
@@ -144,25 +141,41 @@ static int clk_pllv2_set_rate(struct clk_hw *hw, unsigned long rate,
 		return -EINVAL;
 	pdf--;
 
-	temp64 = rate * (pdf+1) - quad_parent_rate * mfi;
-	do_div(temp64, quad_parent_rate/1000000);
+	temp64 = rate * (pdf + 1) - quad_parent_rate * mfi;
+	do_div(temp64, quad_parent_rate / 1000000);
 	mfn = (long)temp64;
 
+	reg = mfi << 4 | pdf;
+
+	*dp_op = reg;
+	*dp_mfd = mfd;
+	*dp_mfn = mfn;
+
+	return 0;
+}
+
+static int clk_pllv2_set_rate(struct clk_hw *hw, unsigned long rate,
+		unsigned long parent_rate)
+{
+	struct clk_pllv2 *pll = to_clk_pllv2(hw);
+	void __iomem *pllbase;
+	u32 dp_ctl, dp_op, dp_mfd, dp_mfn;
+	int ret;
+
+	pllbase = pll->base;
+
+
+	ret = __clk_pllv2_set_rate(rate, parent_rate, &dp_op, &dp_mfd, &dp_mfn);
+	if (ret)
+		return ret;
+
 	dp_ctl = __raw_readl(pllbase + MXC_PLL_DP_CTL);
 	/* use dpdck0_2 */
 	__raw_writel(dp_ctl | 0x1000L, pllbase + MXC_PLL_DP_CTL);
-	pll_hfsm = dp_ctl & MXC_PLL_DP_CTL_HFSM;
-	if (pll_hfsm == 0) {
-		reg = mfi << 4 | pdf;
-		__raw_writel(reg, pllbase + MXC_PLL_DP_OP);
-		__raw_writel(mfd, pllbase + MXC_PLL_DP_MFD);
-		__raw_writel(mfn, pllbase + MXC_PLL_DP_MFN);
-	} else {
-		reg = mfi << 4 | pdf;
-		__raw_writel(reg, pllbase + MXC_PLL_DP_HFS_OP);
-		__raw_writel(mfd, pllbase + MXC_PLL_DP_HFS_MFD);
-		__raw_writel(mfn, pllbase + MXC_PLL_DP_HFS_MFN);
-	}
+
+	__raw_writel(dp_op, pllbase + MXC_PLL_DP_OP);
+	__raw_writel(dp_mfd, pllbase + MXC_PLL_DP_MFD);
+	__raw_writel(dp_mfn, pllbase + MXC_PLL_DP_MFN);
 
 	return 0;
 }
@@ -170,7 +183,11 @@ static int clk_pllv2_set_rate(struct clk_hw *hw, unsigned long rate,
 static long clk_pllv2_round_rate(struct clk_hw *hw, unsigned long rate,
 		unsigned long *prate)
 {
-	return rate;
+	u32 dp_op, dp_mfd, dp_mfn;
+
+	__clk_pllv2_set_rate(rate, *prate, &dp_op, &dp_mfd, &dp_mfn);
+	return __clk_pllv2_recalc_rate(*prate, MXC_PLL_DP_CTL_DPDCK0_2_EN,
+			dp_op, dp_mfd, dp_mfn);
 }
 
 static int clk_pllv2_prepare(struct clk_hw *hw)

arch/arm/mach-imx/crm-regs-imx5.h

@@ -23,7 +23,7 @@
 #define MX53_DPLL1_BASE		MX53_IO_ADDRESS(MX53_PLL1_BASE_ADDR)
 #define MX53_DPLL2_BASE		MX53_IO_ADDRESS(MX53_PLL2_BASE_ADDR)
 #define MX53_DPLL3_BASE		MX53_IO_ADDRESS(MX53_PLL3_BASE_ADDR)
-#define MX53_DPLL4_BASE		MX53_IO_ADDRESS(MX53_PLL3_BASE_ADDR)
+#define MX53_DPLL4_BASE		MX53_IO_ADDRESS(MX53_PLL4_BASE_ADDR)
 
 /* PLL Register Offsets */
 #define MXC_PLL_DP_CTL			0x00

arch/arm/mach-imx/hotplug.c

@@ -12,6 +12,7 @@
 
 #include <linux/errno.h>
 #include <asm/cacheflush.h>
+#include <asm/cp15.h>
 #include <mach/common.h>
 
 int platform_cpu_kill(unsigned int cpu)
@@ -19,6 +20,44 @@ int platform_cpu_kill(unsigned int cpu)
 	return 1;
 }
 
+static inline void cpu_enter_lowpower(void)
+{
+	unsigned int v;
+
+	flush_cache_all();
+	asm volatile(
+		"mcr	p15, 0, %1, c7, c5, 0\n"
+	"	mcr	p15, 0, %1, c7, c10, 4\n"
+	/*
+	 * Turn off coherency
+	 */
+	"	mrc	p15, 0, %0, c1, c0, 1\n"
+	"	bic	%0, %0, %3\n"
+	"	mcr	p15, 0, %0, c1, c0, 1\n"
+	"	mrc	p15, 0, %0, c1, c0, 0\n"
+	"	bic	%0, %0, %2\n"
+	"	mcr	p15, 0, %0, c1, c0, 0\n"
+	  : "=&r" (v)
+	  : "r" (0), "Ir" (CR_C), "Ir" (0x40)
+	  : "cc");
+}
+
+static inline void cpu_leave_lowpower(void)
+{
+	unsigned int v;
+
+	asm volatile(
+		"mrc	p15, 0, %0, c1, c0, 0\n"
+	"	orr	%0, %0, %1\n"
+	"	mcr	p15, 0, %0, c1, c0, 0\n"
+	"	mrc	p15, 0, %0, c1, c0, 1\n"
+	"	orr	%0, %0, %2\n"
+	"	mcr	p15, 0, %0, c1, c0, 1\n"
+	  : "=&r" (v)
+	  : "Ir" (CR_C), "Ir" (0x40)
+	  : "cc");
+}
+
 /*
  * platform-specific code to shutdown a CPU
  *
@@ -26,9 +65,10 @@ int platform_cpu_kill(unsigned int cpu)
  */
 void platform_cpu_die(unsigned int cpu)
 {
-	flush_cache_all();
+	cpu_enter_lowpower();
 	imx_enable_cpu(cpu, false);
 	cpu_do_idle();
+	cpu_leave_lowpower();
 
 	/* We should never return from idle */
 	panic("cpu %d unexpectedly exit from shutdown\n", cpu);

arch/arm/mach-imx/mach-cpuimx35.c

@@ -70,7 +70,6 @@ static struct i2c_board_info eukrea_cpuimx35_i2c_devices[] = {
 		I2C_BOARD_INFO("pcf8563", 0x51),
 	}, {
 		I2C_BOARD_INFO("tsc2007", 0x48),
-		.type		= "tsc2007",
 		.platform_data	= &tsc2007_info,
 		.irq		= IMX_GPIO_TO_IRQ(TSC2007_IRQGPIO),
 	},

arch/arm/mach-imx/mach-cpuimx51sd.c

@@ -142,7 +142,6 @@ static struct i2c_board_info eukrea_cpuimx51sd_i2c_devices[] = {
 		I2C_BOARD_INFO("pcf8563", 0x51),
 	}, {
 		I2C_BOARD_INFO("tsc2007", 0x49),
-		.type		= "tsc2007",
 		.platform_data	= &tsc2007_info,
 	},
 };

arch/arm/mach-imx/mach-imx27_visstrim_m10.c

@@ -116,6 +116,8 @@ static const int visstrim_m10_pins[] __initconst = {
 	PB23_PF_USB_PWR,
 	PB24_PF_USB_OC,
 	/* CSI */
+	TVP5150_RSTN | GPIO_GPIO | GPIO_OUT,
+	TVP5150_PWDN | GPIO_GPIO | GPIO_OUT,
 	PB10_PF_CSI_D0,
 	PB11_PF_CSI_D1,
 	PB12_PF_CSI_D2,
@@ -147,6 +149,24 @@ static struct gpio visstrim_m10_version_gpios[] = {
 	{ MOTHERBOARD_BIT2, GPIOF_IN, "mother-version-2" },
 };
 
+static const struct gpio visstrim_m10_gpios[] __initconst = {
+	{
+		.gpio = TVP5150_RSTN,
+		.flags = GPIOF_DIR_OUT | GPIOF_INIT_HIGH,
+		.label = "tvp5150_rstn",
+	},
+	{
+		.gpio = TVP5150_PWDN,
+		.flags = GPIOF_DIR_OUT | GPIOF_INIT_LOW,
+		.label = "tvp5150_pwdn",
+	},
+	{
+		.gpio = OTG_PHY_CS_GPIO,
+		.flags = GPIOF_DIR_OUT | GPIOF_INIT_LOW,
+		.label = "usbotg_cs",
+	},
+};
+
 /* Camera */
 static int visstrim_camera_power(struct device *dev, int on)
 {
@@ -190,13 +210,6 @@ static void __init visstrim_camera_init(void)
 	struct platform_device *pdev;
 	int dma;
 
-	/* Initialize tvp5150 gpios */
-	mxc_gpio_mode(TVP5150_RSTN | GPIO_GPIO | GPIO_OUT);
-	mxc_gpio_mode(TVP5150_PWDN | GPIO_GPIO | GPIO_OUT);
-	gpio_set_value(TVP5150_RSTN, 1);
-	gpio_set_value(TVP5150_PWDN, 0);
-	ndelay(1);
-
 	gpio_set_value(TVP5150_PWDN, 1);
 	ndelay(1);
 	gpio_set_value(TVP5150_RSTN, 0);
@@ -377,10 +390,6 @@ static struct i2c_board_info visstrim_m10_i2c_devices[] = {
 /* USB OTG */
 static int otg_phy_init(struct platform_device *pdev)
 {
-	gpio_set_value(OTG_PHY_CS_GPIO, 0);
-
-	mdelay(10);
-
 	return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
 }
 
@@ -435,6 +444,11 @@ static void __init visstrim_m10_board_init(void)
 	if (ret)
 		pr_err("Failed to setup pins (%d)\n", ret);
 
+	ret = gpio_request_array(visstrim_m10_gpios,
+				ARRAY_SIZE(visstrim_m10_gpios));
+	if (ret)
+		pr_err("Failed to request gpios (%d)\n", ret);
+
 	imx27_add_imx_ssi(0, &visstrim_m10_ssi_pdata);
 	imx27_add_imx_uart0(&uart_pdata);
 

arch/arm/mach-imx/mach-mx21ads.c

@@ -32,7 +32,7 @@
  * Memory-mapped I/O on MX21ADS base board
  */
 #define MX21ADS_MMIO_BASE_ADDR   0xf5000000
-#define MX21ADS_MMIO_SIZE        SZ_16M
+#define MX21ADS_MMIO_SIZE        0xc00000
 
 #define MX21ADS_REG_ADDR(offset)    (void __force __iomem *) \
 		(MX21ADS_MMIO_BASE_ADDR + (offset))

arch/arm/mach-imx/mm-imx3.c

@@ -86,6 +86,7 @@ static void __iomem *imx3_ioremap_caller(unsigned long phys_addr, size_t size,
 
 void __init imx3_init_l2x0(void)
 {
+#ifdef CONFIG_CACHE_L2X0
 	void __iomem *l2x0_base;
 	void __iomem *clkctl_base;
 
@@ -115,6 +116,7 @@ void __init imx3_init_l2x0(void)
 	}
 
 	l2x0_init(l2x0_base, 0x00030024, 0x00000000);
+#endif
 }
 
 #ifdef CONFIG_SOC_IMX31
@@ -179,6 +181,8 @@ void __init imx31_soc_init(void)
 	mxc_register_gpio("imx31-gpio", 1, MX31_GPIO2_BASE_ADDR, SZ_16K, MX31_INT_GPIO2, 0);
 	mxc_register_gpio("imx31-gpio", 2, MX31_GPIO3_BASE_ADDR, SZ_16K, MX31_INT_GPIO3, 0);
 
+	pinctrl_provide_dummies();
+
 	if (to_version == 1) {
 		strncpy(imx31_sdma_pdata.fw_name, "sdma-imx31-to1.bin",
 			strlen(imx31_sdma_pdata.fw_name));

arch/arm/mach-imx/mm-imx5.c

@@ -202,6 +202,8 @@ void __init imx51_soc_init(void)
 	mxc_register_gpio("imx31-gpio", 2, MX51_GPIO3_BASE_ADDR, SZ_16K, MX51_INT_GPIO3_LOW, MX51_INT_GPIO3_HIGH);
 	mxc_register_gpio("imx31-gpio", 3, MX51_GPIO4_BASE_ADDR, SZ_16K, MX51_INT_GPIO4_LOW, MX51_INT_GPIO4_HIGH);
 
+	pinctrl_provide_dummies();
+
 	/* i.mx51 has the i.mx35 type sdma */
 	imx_add_imx_sdma("imx35-sdma", MX51_SDMA_BASE_ADDR, MX51_INT_SDMA, &imx51_sdma_pdata);
 

arch/arm/mach-kirkwood/board-iconnect.c

@@ -20,9 +20,6 @@
 #include <linux/mv643xx_eth.h>
 #include <linux/gpio.h>
 #include <linux/leds.h>
-#include <linux/spi/flash.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/orion_spi.h>
 #include <linux/i2c.h>
 #include <linux/input.h>
 #include <linux/gpio_keys.h>

arch/arm/mach-kirkwood/common.c

@@ -159,6 +159,7 @@ static struct clk __init *clk_register_gate_fn(struct device *dev,
 	gate_fn->gate.flags = clk_gate_flags;
 	gate_fn->gate.lock = lock;
 	gate_fn->gate.hw.init = &init;
+	gate_fn->fn = fn;
 
 	/* ops is the gate ops, but with our disable function */
 	if (clk_gate_fn_ops.disable != clk_gate_fn_disable) {
@@ -193,9 +194,11 @@ static struct clk __init *kirkwood_register_gate_fn(const char *name,
 				    bit_idx, 0, &gating_lock, fn);
 }
 
+static struct clk *ge0, *ge1;
+
 void __init kirkwood_clk_init(void)
 {
-	struct clk *runit, *ge0, *ge1, *sata0, *sata1, *usb0, *sdio;
+	struct clk *runit, *sata0, *sata1, *usb0, *sdio;
 	struct clk *crypto, *xor0, *xor1, *pex0, *pex1, *audio;
 
 	tclk = clk_register_fixed_rate(NULL, "tclk", NULL,
@@ -257,6 +260,9 @@ void __init kirkwood_ge00_init(struct mv643xx_eth_platform_data *eth_data)
 	orion_ge00_init(eth_data,
 			GE00_PHYS_BASE, IRQ_KIRKWOOD_GE00_SUM,
 			IRQ_KIRKWOOD_GE00_ERR);
+	/* The interface forgets the MAC address assigned by u-boot if
+	the clock is turned off, so claim the clk now. */
+	clk_prepare_enable(ge0);
 }
 
 
@@ -268,6 +274,7 @@ void __init kirkwood_ge01_init(struct mv643xx_eth_platform_data *eth_data)
 	orion_ge01_init(eth_data,
 			GE01_PHYS_BASE, IRQ_KIRKWOOD_GE01_SUM,
 			IRQ_KIRKWOOD_GE01_ERR);
+	clk_prepare_enable(ge1);
 }
 
 

arch/arm/mach-kirkwood/include/mach/bridge-regs.h

@@ -38,6 +38,7 @@
 #define IRQ_MASK_HIGH_OFF	0x0014
 
 #define TIMER_VIRT_BASE		(BRIDGE_VIRT_BASE | 0x0300)
+#define TIMER_PHYS_BASE		(BRIDGE_PHYS_BASE | 0x0300)
 
 #define L2_CONFIG_REG		(BRIDGE_VIRT_BASE | 0x0128)
 #define L2_WRITETHROUGH		0x00000010

arch/arm/mach-kirkwood/include/mach/kirkwood.h

@@ -80,6 +80,7 @@
 #define  UART1_VIRT_BASE	(DEV_BUS_VIRT_BASE | 0x2100)
 
 #define BRIDGE_VIRT_BASE	(KIRKWOOD_REGS_VIRT_BASE | 0x20000)
+#define BRIDGE_PHYS_BASE	(KIRKWOOD_REGS_PHYS_BASE | 0x20000)
 
 #define CRYPTO_PHYS_BASE	(KIRKWOOD_REGS_PHYS_BASE | 0x30000)
 

arch/arm/mach-mmp/irq.c

@@ -241,6 +241,7 @@ void __init mmp2_init_icu(void)
 	icu_data[1].clr_mfp_irq_base = IRQ_MMP2_PMIC_BASE;
 	icu_data[1].clr_mfp_hwirq = IRQ_MMP2_PMIC - IRQ_MMP2_PMIC_BASE;
 	icu_data[1].nr_irqs = 2;
+	icu_data[1].cascade_irq = 4;
 	icu_data[1].virq_base = IRQ_MMP2_PMIC_BASE;
 	icu_data[1].domain = irq_domain_add_legacy(NULL, icu_data[1].nr_irqs,
 						   icu_data[1].virq_base, 0,
@@ -249,6 +250,7 @@ void __init mmp2_init_icu(void)
 	icu_data[2].reg_status = mmp_icu_base + 0x154;
 	icu_data[2].reg_mask = mmp_icu_base + 0x16c;
 	icu_data[2].nr_irqs = 2;
+	icu_data[2].cascade_irq = 5;
 	icu_data[2].virq_base = IRQ_MMP2_RTC_BASE;
 	icu_data[2].domain = irq_domain_add_legacy(NULL, icu_data[2].nr_irqs,
 						   icu_data[2].virq_base, 0,
@@ -257,6 +259,7 @@ void __init mmp2_init_icu(void)
 	icu_data[3].reg_status = mmp_icu_base + 0x180;
 	icu_data[3].reg_mask = mmp_icu_base + 0x17c;
 	icu_data[3].nr_irqs = 3;
+	icu_data[3].cascade_irq = 9;
 	icu_data[3].virq_base = IRQ_MMP2_KEYPAD_BASE;
 	icu_data[3].domain = irq_domain_add_legacy(NULL, icu_data[3].nr_irqs,
 						   icu_data[3].virq_base, 0,
@@ -265,6 +268,7 @@ void __init mmp2_init_icu(void)
 	icu_data[4].reg_status = mmp_icu_base + 0x158;
 	icu_data[4].reg_mask = mmp_icu_base + 0x170;
 	icu_data[4].nr_irqs = 5;
+	icu_data[4].cascade_irq = 17;
 	icu_data[4].virq_base = IRQ_MMP2_TWSI_BASE;
 	icu_data[4].domain = irq_domain_add_legacy(NULL, icu_data[4].nr_irqs,
 						   icu_data[4].virq_base, 0,
@@ -273,6 +277,7 @@ void __init mmp2_init_icu(void)
 	icu_data[5].reg_status = mmp_icu_base + 0x15c;
 	icu_data[5].reg_mask = mmp_icu_base + 0x174;
 	icu_data[5].nr_irqs = 15;
+	icu_data[5].cascade_irq = 35;
 	icu_data[5].virq_base = IRQ_MMP2_MISC_BASE;
 	icu_data[5].domain = irq_domain_add_legacy(NULL, icu_data[5].nr_irqs,
 						   icu_data[5].virq_base, 0,
@@ -281,6 +286,7 @@ void __init mmp2_init_icu(void)
 	icu_data[6].reg_status = mmp_icu_base + 0x160;
 	icu_data[6].reg_mask = mmp_icu_base + 0x178;
 	icu_data[6].nr_irqs = 2;
+	icu_data[6].cascade_irq = 51;
 	icu_data[6].virq_base = IRQ_MMP2_MIPI_HSI1_BASE;
 	icu_data[6].domain = irq_domain_add_legacy(NULL, icu_data[6].nr_irqs,
 						   icu_data[6].virq_base, 0,
@@ -289,6 +295,7 @@ void __init mmp2_init_icu(void)
 	icu_data[7].reg_status = mmp_icu_base + 0x188;
 	icu_data[7].reg_mask = mmp_icu_base + 0x184;
 	icu_data[7].nr_irqs = 2;
+	icu_data[7].cascade_irq = 55;
 	icu_data[7].virq_base = IRQ_MMP2_MIPI_HSI0_BASE;
 	icu_data[7].domain = irq_domain_add_legacy(NULL, icu_data[7].nr_irqs,
 						   icu_data[7].virq_base, 0,

arch/arm/mach-omap2/board-n8x0.c

@@ -83,11 +83,9 @@ static struct musb_hdrc_config musb_config = {
 };
 
 static struct musb_hdrc_platform_data tusb_data = {
-#if defined(CONFIG_USB_MUSB_OTG)
+#ifdef CONFIG_USB_GADGET_MUSB_HDRC
 	.mode		= MUSB_OTG,
-#elif defined(CONFIG_USB_MUSB_PERIPHERAL)
-	.mode		= MUSB_PERIPHERAL,
-#else /* defined(CONFIG_USB_MUSB_HOST) */
+#else
 	.mode		= MUSB_HOST,
 #endif
 	.set_power	= tusb_set_power,

arch/arm/mach-omap2/board-omap3beagle.c

@@ -81,13 +81,13 @@ static u8 omap3_beagle_version;
 static struct {
 	int mmc1_gpio_wp;
 	int usb_pwr_level;
-	int reset_gpio;
+	int dvi_pd_gpio;
 	int usr_button_gpio;
 	int mmc_caps;
 } beagle_config = {
 	.mmc1_gpio_wp = -EINVAL,
 	.usb_pwr_level = GPIOF_OUT_INIT_LOW,
-	.reset_gpio = 129,
+	.dvi_pd_gpio = -EINVAL,
 	.usr_button_gpio = 4,
 	.mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 };
@@ -126,21 +126,21 @@ static void __init omap3_beagle_init_rev(void)
 		printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
 		beagle_config.mmc1_gpio_wp = 29;
-		beagle_config.reset_gpio = 170;
+		beagle_config.dvi_pd_gpio = 170;
 		beagle_config.usr_button_gpio = 7;
 		break;
 	case 6:
 		printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
 		beagle_config.mmc1_gpio_wp = 23;
-		beagle_config.reset_gpio = 170;
+		beagle_config.dvi_pd_gpio = 170;
 		beagle_config.usr_button_gpio = 7;
 		break;
 	case 5:
 		printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
 		beagle_config.mmc1_gpio_wp = 23;
-		beagle_config.reset_gpio = 170;
+		beagle_config.dvi_pd_gpio = 170;
 		beagle_config.usr_button_gpio = 7;
 		break;
 	case 0:
@@ -274,11 +274,9 @@ static int beagle_twl_gpio_setup(struct device *dev,
 		if (r)
 			pr_err("%s: unable to configure nDVI_PWR_EN\n",
 				__func__);
-		r = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH,
-				     "DVI_LDO_EN");
-		if (r)
-			pr_err("%s: unable to configure DVI_LDO_EN\n",
-				__func__);
+
+		beagle_config.dvi_pd_gpio = gpio + 2;
+
 	} else {
 		/*
 		 * REVISIT: need ehci-omap hooks for external VBUS
@@ -287,7 +285,7 @@ static int beagle_twl_gpio_setup(struct device *dev,
 		if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
 			pr_err("%s: unable to configure EHCI_nOC\n", __func__);
 	}
-	dvi_panel.power_down_gpio = beagle_config.reset_gpio;
+	dvi_panel.power_down_gpio = beagle_config.dvi_pd_gpio;
 
 	gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level,
 			"nEN_USB_PWR");
@@ -499,7 +497,7 @@ static void __init omap3_beagle_init(void)
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
 	omap3_beagle_init_rev();
 
-	if (beagle_config.mmc1_gpio_wp != -EINVAL)
+	if (gpio_is_valid(beagle_config.mmc1_gpio_wp))
 		omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
 	mmc[0].caps = beagle_config.mmc_caps;
 	omap_hsmmc_init(mmc);
@@ -510,15 +508,13 @@ static void __init omap3_beagle_init(void)
 
 	platform_add_devices(omap3_beagle_devices,
 			ARRAY_SIZE(omap3_beagle_devices));
+	if (gpio_is_valid(beagle_config.dvi_pd_gpio))
+		omap_mux_init_gpio(beagle_config.dvi_pd_gpio, OMAP_PIN_OUTPUT);
 	omap_display_init(&beagle_dss_data);
 	omap_serial_init();
 	omap_sdrc_init(mt46h32m32lf6_sdrc_params,
 				  mt46h32m32lf6_sdrc_params);
 
-	omap_mux_init_gpio(170, OMAP_PIN_INPUT);
-	/* REVISIT leave DVI powered down until it's needed ... */
-	gpio_request_one(170, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
-
 	usb_musb_init(NULL);
 	usbhs_init(&usbhs_bdata);
 	omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions,

arch/arm/mach-omap2/board-rx51-peripherals.c

@@ -144,7 +144,6 @@ static struct lis3lv02d_platform_data rx51_lis3lv02d_data = {
 	.release_resources = lis302_release,
 	.st_min_limits = {-32, 3, 3},
 	.st_max_limits = {-3, 32, 32},
-	.irq2 = OMAP_GPIO_IRQ(LIS302_IRQ2_GPIO),
 };
 #endif
 
@@ -1030,7 +1029,6 @@ static struct i2c_board_info __initdata rx51_peripherals_i2c_board_info_3[] = {
 	{
 		I2C_BOARD_INFO("lis3lv02d", 0x1d),
 		.platform_data = &rx51_lis3lv02d_data,
-		.irq = OMAP_GPIO_IRQ(LIS302_IRQ1_GPIO),
 	},
 #endif
 };
@@ -1056,6 +1054,10 @@ static int __init rx51_i2c_init(void)
 	omap_pmic_init(1, 2200, "twl5030", INT_34XX_SYS_NIRQ, &rx51_twldata);
 	omap_register_i2c_bus(2, 100, rx51_peripherals_i2c_board_info_2,
 			      ARRAY_SIZE(rx51_peripherals_i2c_board_info_2));
+#if defined(CONFIG_SENSORS_LIS3_I2C) || defined(CONFIG_SENSORS_LIS3_I2C_MODULE)
+	rx51_lis3lv02d_data.irq2 = gpio_to_irq(LIS302_IRQ2_GPIO);
+	rx51_peripherals_i2c_board_info_3[0].irq = gpio_to_irq(LIS302_IRQ1_GPIO);
+#endif
 	omap_register_i2c_bus(3, 400, rx51_peripherals_i2c_board_info_3,
 			      ARRAY_SIZE(rx51_peripherals_i2c_board_info_3));
 	return 0;

arch/arm/mach-omap2/clock3xxx_data.c

@@ -3514,7 +3514,7 @@ int __init omap3xxx_clk_init(void)
 	struct omap_clk *c;
 	u32 cpu_clkflg = 0;
 
-	if (cpu_is_omap3517()) {
+	if (soc_is_am35xx()) {
 		cpu_mask = RATE_IN_34XX;
 		cpu_clkflg = CK_AM35XX;
 	} else if (cpu_is_omap3630()) {

arch/arm/mach-omap2/clock44xx_data.c

@@ -84,6 +84,7 @@ static struct clk slimbus_clk = {
 
 static struct clk sys_32k_ck = {
 	.name		= "sys_32k_ck",
+	.clkdm_name	= "prm_clkdm",
 	.rate		= 32768,
 	.ops		= &clkops_null,
 };
@@ -512,6 +513,7 @@ static struct clk ddrphy_ck = {
 	.name		= "ddrphy_ck",
 	.parent		= &dpll_core_m2_ck,
 	.ops		= &clkops_null,
+	.clkdm_name	= "l3_emif_clkdm",
 	.fixed_div	= 2,
 	.recalc		= &omap_fixed_divisor_recalc,
 };
@@ -769,6 +771,7 @@ static const struct clksel dpll_mpu_m2_div[] = {
 static struct clk dpll_mpu_m2_ck = {
 	.name		= "dpll_mpu_m2_ck",
 	.parent		= &dpll_mpu_ck,
+	.clkdm_name	= "cm_clkdm",
 	.clksel		= dpll_mpu_m2_div,
 	.clksel_reg	= OMAP4430_CM_DIV_M2_DPLL_MPU,
 	.clksel_mask	= OMAP4430_DPLL_CLKOUT_DIV_MASK,
@@ -1149,6 +1152,7 @@ static const struct clksel l3_div_div[] = {
 static struct clk l3_div_ck = {
 	.name		= "l3_div_ck",
 	.parent		= &div_core_ck,
+	.clkdm_name	= "cm_clkdm",
 	.clksel		= l3_div_div,
 	.clksel_reg	= OMAP4430_CM_CLKSEL_CORE,
 	.clksel_mask	= OMAP4430_CLKSEL_L3_MASK,
@@ -2824,6 +2828,7 @@ static const struct clksel trace_clk_div_div[] = {
 static struct clk trace_clk_div_ck = {
 	.name		= "trace_clk_div_ck",
 	.parent		= &pmd_trace_clk_mux_ck,
+	.clkdm_name	= "emu_sys_clkdm",
 	.clksel		= trace_clk_div_div,
 	.clksel_reg	= OMAP4430_CM_EMU_DEBUGSS_CLKCTRL,
 	.clksel_mask	= OMAP4430_CLKSEL_PMD_TRACE_CLK_MASK,

arch/arm/mach-omap2/cm.h

@@ -22,4 +22,15 @@
  */
 #define MAX_MODULE_READY_TIME		2000
 
+/*
+ * MAX_MODULE_DISABLE_TIME: max duration in microseconds to wait for
+ * the PRCM to request that a module enter the inactive state in the
+ * case of OMAP2 & 3.  In the case of OMAP4 this is the max duration
+ * in microseconds for the module to reach the inactive state from
+ * a functional state.
+ * XXX FSUSB on OMAP4430 takes ~4ms to idle after reset during
+ * kernel init.
+ */
+#define MAX_MODULE_DISABLE_TIME		5000
+
 #endif

arch/arm/mach-omap2/cminst44xx.c

@@ -313,9 +313,9 @@ int omap4_cminst_wait_module_idle(u8 part, u16 inst, s16 cdoffs, u16 clkctrl_off
 
 	omap_test_timeout((_clkctrl_idlest(part, inst, cdoffs, clkctrl_offs) ==
 			   CLKCTRL_IDLEST_DISABLED),
-			  MAX_MODULE_READY_TIME, i);
+			  MAX_MODULE_DISABLE_TIME, i);
 
-	return (i < MAX_MODULE_READY_TIME) ? 0 : -EBUSY;
+	return (i < MAX_MODULE_DISABLE_TIME) ? 0 : -EBUSY;
 }
 
 /**

arch/arm/mach-omap2/dsp.c

@@ -20,6 +20,9 @@
 
 #include <linux/module.h>
 #include <linux/platform_device.h>
+
+#include <asm/memblock.h>
+
 #include "cm2xxx_3xxx.h"
 #include "prm2xxx_3xxx.h"
 #ifdef CONFIG_BRIDGE_DVFS

arch/arm/mach-omap2/id.c

@@ -246,6 +246,17 @@ void __init omap3xxx_check_features(void)
 
 	omap_features |= OMAP3_HAS_SDRC;
 
+	/*
+	 * am35x fixups:
+	 * - The am35x Chip ID register has bits 12, 7:5, and 3:2 marked as
+	 *   reserved and therefore return 0 when read.  Unfortunately,
+	 *   OMAP3_CHECK_FEATURE() will interpret some of those zeroes to
+	 *   mean that a feature is present even though it isn't so clear
+	 *   the incorrectly set feature bits.
+	 */
+	if (soc_is_am35xx())
+		omap_features &= ~(OMAP3_HAS_IVA | OMAP3_HAS_ISP);
+
 	/*
 	 * TODO: Get additional info (where applicable)
 	 *       e.g. Size of L2 cache.

arch/arm/mach-omap2/irq.c

@@ -149,6 +149,7 @@ omap_alloc_gc(void __iomem *base, unsigned int irq_start, unsigned int num)
 	ct->chip.irq_ack = omap_mask_ack_irq;
 	ct->chip.irq_mask = irq_gc_mask_disable_reg;
 	ct->chip.irq_unmask = irq_gc_unmask_enable_reg;
+	ct->chip.flags |= IRQCHIP_SKIP_SET_WAKE;
 
 	ct->regs.enable = INTC_MIR_CLEAR0;
 	ct->regs.disable = INTC_MIR_SET0;

arch/arm/mach-omap2/mux.c

@@ -41,6 +41,7 @@
 #include "control.h"
 #include "mux.h"
 #include "prm.h"
+#include "common.h"
 
 #define OMAP_MUX_BASE_OFFSET		0x30	/* Offset from CTRL_BASE */
 #define OMAP_MUX_BASE_SZ		0x5ca
@@ -217,8 +218,7 @@ static int __init _omap_mux_get_by_name(struct omap_mux_partition *partition,
 	return -ENODEV;
 }
 
-static int __init
-omap_mux_get_by_name(const char *muxname,
+int __init omap_mux_get_by_name(const char *muxname,
 			struct omap_mux_partition **found_partition,
 			struct omap_mux **found_mux)
 {

arch/arm/mach-omap2/mux.h

@@ -59,6 +59,7 @@
 #define OMAP_PIN_OFF_WAKEUPENABLE	OMAP_WAKEUP_EN
 
 #define OMAP_MODE_GPIO(x)	(((x) & OMAP_MUX_MODE7) == OMAP_MUX_MODE4)
+#define OMAP_MODE_UART(x)	(((x) & OMAP_MUX_MODE7) == OMAP_MUX_MODE0)
 
 /* Flags for omapX_mux_init */
 #define OMAP_PACKAGE_MASK		0xffff
@@ -225,8 +226,18 @@ omap_hwmod_mux_init(struct omap_device_pad *bpads, int nr_pads);
  */
 void omap_hwmod_mux(struct omap_hwmod_mux_info *hmux, u8 state);
 
+int omap_mux_get_by_name(const char *muxname,
+		struct omap_mux_partition **found_partition,
+		struct omap_mux **found_mux);
 #else
 
+static inline int omap_mux_get_by_name(const char *muxname,
+		struct omap_mux_partition **found_partition,
+		struct omap_mux **found_mux)
+{
+	return 0;
+}
+
 static inline int omap_mux_init_gpio(int gpio, int val)
 {
 	return 0;

arch/arm/mach-omap2/omap_hwmod.c

@@ -530,7 +530,7 @@ static int _disable_wakeup(struct omap_hwmod *oh, u32 *v)
 	if (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP)
 		_set_slave_idlemode(oh, HWMOD_IDLEMODE_SMART, v);
 	if (oh->class->sysc->idlemodes & MSTANDBY_SMART_WKUP)
-		_set_master_standbymode(oh, HWMOD_IDLEMODE_SMART_WKUP, v);
+		_set_master_standbymode(oh, HWMOD_IDLEMODE_SMART, v);
 
 	/* XXX test pwrdm_get_wken for this hwmod's subsystem */
 

arch/arm/mach-omap2/omap_hwmod_44xx_data.c

@@ -393,8 +393,7 @@ static struct omap_hwmod_class_sysconfig omap44xx_counter_sysc = {
 	.rev_offs	= 0x0000,
 	.sysc_offs	= 0x0004,
 	.sysc_flags	= SYSC_HAS_SIDLEMODE,
-	.idlemodes	= (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
-			   SIDLE_SMART_WKUP),
+	.idlemodes	= (SIDLE_FORCE | SIDLE_NO),
 	.sysc_fields	= &omap_hwmod_sysc_type1,
 };
 
@@ -854,6 +853,11 @@ static struct omap_hwmod omap44xx_dss_hdmi_hwmod = {
 	.name		= "dss_hdmi",
 	.class		= &omap44xx_hdmi_hwmod_class,
 	.clkdm_name	= "l3_dss_clkdm",
+	/*
+	 * HDMI audio requires to use no-idle mode. Hence,
+	 * set idle mode by software.
+	 */
+	.flags		= HWMOD_SWSUP_SIDLE,
 	.mpu_irqs	= omap44xx_dss_hdmi_irqs,
 	.sdma_reqs	= omap44xx_dss_hdmi_sdma_reqs,
 	.main_clk	= "dss_48mhz_clk",

arch/arm/mach-omap2/omap_l3_smx.c

@@ -155,10 +155,11 @@ static irqreturn_t omap3_l3_block_irq(struct omap3_l3 *l3,
 	u8 multi = error & L3_ERROR_LOG_MULTI;
 	u32 address = omap3_l3_decode_addr(error_addr);
 
-	WARN(true, "%s seen by %s %s at address %x\n",
+	pr_err("%s seen by %s %s at address %x\n",
 			omap3_l3_code_string(code),
 			omap3_l3_initiator_string(initid),
 			multi ? "Multiple Errors" : "", address);
+	WARN_ON(1);
 
 	return IRQ_HANDLED;
 }

arch/arm/mach-omap2/omap_phy_internal.c

@@ -239,21 +239,15 @@ void am35x_set_mode(u8 musb_mode)
 
 	devconf2 &= ~CONF2_OTGMODE;
 	switch (musb_mode) {
-#ifdef	CONFIG_USB_MUSB_HDRC_HCD
 	case MUSB_HOST:		/* Force VBUS valid, ID = 0 */
 		devconf2 |= CONF2_FORCE_HOST;
 		break;
-#endif
-#ifdef	CONFIG_USB_GADGET_MUSB_HDRC
 	case MUSB_PERIPHERAL:	/* Force VBUS valid, ID = 1 */
 		devconf2 |= CONF2_FORCE_DEVICE;
 		break;
-#endif
-#ifdef	CONFIG_USB_MUSB_OTG
 	case MUSB_OTG:		/* Don't override the VBUS/ID comparators */
 		devconf2 |= CONF2_NO_OVERRIDE;
 		break;
-#endif
 	default:
 		pr_info(KERN_INFO "Unsupported mode %u\n", musb_mode);
 	}

arch/arm/mach-omap2/pm34xx.c

@@ -724,6 +724,7 @@ int __init omap3_pm_init(void)
 	ret = request_irq(omap_prcm_event_to_irq("io"),
 		_prcm_int_handle_io, IRQF_SHARED | IRQF_NO_SUSPEND, "pm_io",
 		omap3_pm_init);
+	enable_irq(omap_prcm_event_to_irq("io"));
 
 	if (ret) {
 		pr_err("pm: Failed to request pm_io irq\n");

arch/arm/mach-omap2/prm2xxx_3xxx.c

@@ -15,6 +15,7 @@
 #include <linux/errno.h>
 #include <linux/err.h>
 #include <linux/io.h>
+#include <linux/irq.h>
 
 #include "common.h"
 #include <plat/cpu.h>
@@ -303,8 +304,15 @@ void omap3xxx_prm_restore_irqen(u32 *saved_mask)
 
 static int __init omap3xxx_prcm_init(void)
 {
-	if (cpu_is_omap34xx())
-		return omap_prcm_register_chain_handler(&omap3_prcm_irq_setup);
-	return 0;
+	int ret = 0;
+
+	if (cpu_is_omap34xx()) {
+		ret = omap_prcm_register_chain_handler(&omap3_prcm_irq_setup);
+		if (!ret)
+			irq_set_status_flags(omap_prcm_event_to_irq("io"),
+					     IRQ_NOAUTOEN);
+	}
+
+	return ret;
 }
 subsys_initcall(omap3xxx_prcm_init);

arch/arm/mach-omap2/serial.c

@@ -57,6 +57,7 @@ struct omap_uart_state {
 
 	struct list_head node;
 	struct omap_hwmod *oh;
+	struct omap_device_pad default_omap_uart_pads[2];
 };
 
 static LIST_HEAD(uart_list);
@@ -126,11 +127,70 @@ static void omap_uart_set_smartidle(struct platform_device *pdev) {}
 #endif /* CONFIG_PM */
 
 #ifdef CONFIG_OMAP_MUX
-static void omap_serial_fill_default_pads(struct omap_board_data *bdata)
+
+#define OMAP_UART_DEFAULT_PAD_NAME_LEN	28
+static char rx_pad_name[OMAP_UART_DEFAULT_PAD_NAME_LEN],
+		tx_pad_name[OMAP_UART_DEFAULT_PAD_NAME_LEN] __initdata;
+
+static void  __init
+omap_serial_fill_uart_tx_rx_pads(struct omap_board_data *bdata,
+				struct omap_uart_state *uart)
+{
+	uart->default_omap_uart_pads[0].name = rx_pad_name;
+	uart->default_omap_uart_pads[0].flags = OMAP_DEVICE_PAD_REMUX |
+							OMAP_DEVICE_PAD_WAKEUP;
+	uart->default_omap_uart_pads[0].enable = OMAP_PIN_INPUT |
+							OMAP_MUX_MODE0;
+	uart->default_omap_uart_pads[0].idle = OMAP_PIN_INPUT | OMAP_MUX_MODE0;
+	uart->default_omap_uart_pads[1].name = tx_pad_name;
+	uart->default_omap_uart_pads[1].enable = OMAP_PIN_OUTPUT |
+							OMAP_MUX_MODE0;
+	bdata->pads = uart->default_omap_uart_pads;
+	bdata->pads_cnt = ARRAY_SIZE(uart->default_omap_uart_pads);
+}
+
+static void  __init omap_serial_check_wakeup(struct omap_board_data *bdata,
+						struct omap_uart_state *uart)
 {
+	struct omap_mux_partition *tx_partition = NULL, *rx_partition = NULL;
+	struct omap_mux *rx_mux = NULL, *tx_mux = NULL;
+	char *rx_fmt, *tx_fmt;
+	int uart_nr = bdata->id + 1;
+
+	if (bdata->id != 2) {
+		rx_fmt = "uart%d_rx.uart%d_rx";
+		tx_fmt = "uart%d_tx.uart%d_tx";
+	} else {
+		rx_fmt = "uart%d_rx_irrx.uart%d_rx_irrx";
+		tx_fmt = "uart%d_tx_irtx.uart%d_tx_irtx";
+	}
+
+	snprintf(rx_pad_name, OMAP_UART_DEFAULT_PAD_NAME_LEN, rx_fmt,
+			uart_nr, uart_nr);
+	snprintf(tx_pad_name, OMAP_UART_DEFAULT_PAD_NAME_LEN, tx_fmt,
+			uart_nr, uart_nr);
+
+	if (omap_mux_get_by_name(rx_pad_name, &rx_partition, &rx_mux) >= 0 &&
+			omap_mux_get_by_name
+				(tx_pad_name, &tx_partition, &tx_mux) >= 0) {
+		u16 tx_mode, rx_mode;
+
+		tx_mode = omap_mux_read(tx_partition, tx_mux->reg_offset);
+		rx_mode = omap_mux_read(rx_partition, rx_mux->reg_offset);
+
+		/*
+		 * Check if uart is used in default tx/rx mode i.e. in mux mode0
+		 * if yes then configure rx pin for wake up capability
+		 */
+		if (OMAP_MODE_UART(rx_mode) && OMAP_MODE_UART(tx_mode))
+			omap_serial_fill_uart_tx_rx_pads(bdata, uart);
+	}
 }
 #else
-static void omap_serial_fill_default_pads(struct omap_board_data *bdata) {}
+static void __init omap_serial_check_wakeup(struct omap_board_data *bdata,
+		struct omap_uart_state *uart)
+{
+}
 #endif
 
 static char *cmdline_find_option(char *str)
@@ -287,8 +347,7 @@ void __init omap_serial_board_init(struct omap_uart_port_info *info)
 		bdata.pads = NULL;
 		bdata.pads_cnt = 0;
 
-		if (cpu_is_omap44xx() || cpu_is_omap34xx())
-			omap_serial_fill_default_pads(&bdata);
+		omap_serial_check_wakeup(&bdata, uart);
 
 		if (!info)
 			omap_serial_init_port(&bdata, NULL);

arch/arm/mach-omap2/usb-musb.c

@@ -41,12 +41,10 @@ static struct musb_hdrc_config musb_config = {
 };
 
 static struct musb_hdrc_platform_data musb_plat = {
-#ifdef CONFIG_USB_MUSB_OTG
+#ifdef CONFIG_USB_GADGET_MUSB_HDRC
 	.mode		= MUSB_OTG,
-#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
+#else
 	.mode		= MUSB_HOST,
-#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
-	.mode		= MUSB_PERIPHERAL,
 #endif
 	/* .clock is set dynamically */
 	.config		= &musb_config,

arch/arm/mach-omap2/usb-tusb6010.c

@@ -300,7 +300,7 @@ tusb6010_setup_interface(struct musb_hdrc_platform_data *data,
 		printk(error, 3, status);
 		return status;
 	}
-	tusb_resources[2].start = irq + IH_GPIO_BASE;
+	tusb_resources[2].start = gpio_to_irq(irq);
 
 	/* set up memory timings ... can speed them up later */
 	if (!ps_refclk) {

arch/arm/mach-orion5x/include/mach/bridge-regs.h

@@ -35,5 +35,5 @@
 #define MAIN_IRQ_MASK		(ORION5X_BRIDGE_VIRT_BASE | 0x204)
 
 #define TIMER_VIRT_BASE		(ORION5X_BRIDGE_VIRT_BASE | 0x300)
-
+#define TIMER_PHYS_BASE		(ORION5X_BRIDGE_PHYS_BASE | 0x300)
 #endif

arch/arm/mach-orion5x/include/mach/io.h

+/*
+ * arch/arm/mach-orion5x/include/mach/io.h
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __ASM_ARCH_IO_H
+#define __ASM_ARCH_IO_H
+
+#include <mach/orion5x.h>
+#include <asm/sizes.h>
+
+#define IO_SPACE_LIMIT		SZ_2M
+static inline void __iomem *__io(unsigned long addr)
+{
+	return (void __iomem *)(addr + ORION5X_PCIE_IO_VIRT_BASE);
+}
+
+#define __io(a)			 __io(a)
+#endif

arch/arm/mach-orion5x/include/mach/orion5x.h

@@ -82,6 +82,7 @@
 #define  UART1_VIRT_BASE		(ORION5X_DEV_BUS_VIRT_BASE | 0x2100)
 
 #define ORION5X_BRIDGE_VIRT_BASE	(ORION5X_REGS_VIRT_BASE | 0x20000)
+#define ORION5X_BRIDGE_PHYS_BASE	(ORION5X_REGS_PHYS_BASE | 0x20000)
 
 #define ORION5X_PCI_VIRT_BASE		(ORION5X_REGS_VIRT_BASE | 0x30000)
 

arch/arm/mach-spear13xx/include/mach/debug-macro.S

@@ -4,7 +4,7 @@
  * Debugging macro include header spear13xx machine family
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/include/mach/dma.h

@@ -4,7 +4,7 @@
  * DMA information for SPEAr13xx machine family
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/include/mach/generic.h

@@ -4,7 +4,7 @@
  * spear13xx machine family generic header file
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/include/mach/gpio.h

@@ -4,7 +4,7 @@
  * GPIO macros for SPEAr13xx machine family
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/include/mach/irqs.h

@@ -4,7 +4,7 @@
  * IRQ helper macros for spear13xx machine family
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/include/mach/spear.h

@@ -4,7 +4,7 @@
  * spear13xx Machine family specific definition
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/include/mach/timex.h

@@ -4,7 +4,7 @@
  * SPEAr3XX machine family specific timex definitions
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/include/mach/uncompress.h

@@ -4,7 +4,7 @@
  * Serial port stubs for kernel decompress status messages
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/spear1310.c

@@ -4,7 +4,7 @@
  * SPEAr1310 machine source file
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/spear1340.c

@@ -4,7 +4,7 @@
  * SPEAr1340 machine source file
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/spear13xx.c

@@ -4,7 +4,7 @@
  * SPEAr13XX machines common source file
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear3xx/include/mach/debug-macro.S

@@ -4,7 +4,7 @@
  * Debugging macro include header spear3xx machine family
  *
  * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Viresh Kumar<viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear3xx/include/mach/generic.h

@@ -4,7 +4,7 @@
  * SPEAr3XX machine family generic header file
  *
  * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Viresh Kumar<viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear3xx/include/mach/gpio.h

@@ -4,7 +4,7 @@
  * GPIO macros for SPEAr3xx machine family
  *
  * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Viresh Kumar<viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear3xx/include/mach/irqs.h

@@ -4,7 +4,7 @@
  * IRQ helper macros for SPEAr3xx machine family
  *
  * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear3xx/include/mach/misc_regs.h

@@ -4,7 +4,7 @@
  * Miscellaneous registers definitions for SPEAr3xx machine family
  *
  * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear3xx/include/mach/spear.h

@@ -4,7 +4,7 @@
  * SPEAr3xx Machine family specific definition
  *
  * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear3xx/include/mach/timex.h

@@ -4,7 +4,7 @@
  * SPEAr3XX machine family specific timex definitions
  *
  * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear3xx/include/mach/uncompress.h

@@ -4,7 +4,7 @@
  * Serial port stubs for kernel decompress status messages
  *
  * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear3xx/spear300.c

@@ -4,7 +4,7 @@
  * SPEAr300 machine source file
  *
  * Copyright (C) 2009-2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear3xx/spear310.c

@@ -4,7 +4,7 @@
  * SPEAr310 machine source file
  *
  * Copyright (C) 2009-2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear3xx/spear320.c

@@ -4,7 +4,7 @@
  * SPEAr320 machine source file
  *
  * Copyright (C) 2009-2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear3xx/spear3xx.c

@@ -4,7 +4,7 @@
  * SPEAr3XX machines common source file
  *
  * Copyright (C) 2009-2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear6xx/include/mach/gpio.h

@@ -4,7 +4,7 @@
  * GPIO macros for SPEAr6xx machine family
  *
  * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any