Staging: rtl8187se: Remove card_type

The vendor-written driver for the RTL8187SE has a private variable
for the card type, even though it only occurs in PCI format.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/staging/rtl8187se/r8180.h

@@ -328,7 +328,6 @@ typedef struct r8180_priv
 
 	short phy_ver; /* meaningful for rtl8225 1:A 2:B 3:C */
 	short enable_gpio0;
-	enum card_type {PCI,MINIPCI,CARDBUS,USB/*rtl8187*/}card_type;
 	short hw_plcp_len;
 	short plcp_preamble_mode; // 0:auto 1:short 2:long
 

drivers/staging/rtl8187se/r8180_core.c

@@ -2911,8 +2911,6 @@ short rtl8180_init(struct net_device *dev)
 	priv->ieee80211->short_slot = 1;
 
 	// just for sync 85
-	priv->card_type = PCI;
-        DMESG("This is a PCI NIC");
 	priv->enable_gpio0 = 0;
 
 	usValue = eprom_read(dev, EEPROM_SW_REVD_OFFSET);
@@ -3233,7 +3231,6 @@ void rtl8185_set_rate(struct net_device *dev)
 void rtl8180_adapter_start(struct net_device *dev)
 {
         struct r8180_priv *priv = ieee80211_priv(dev);
-	u8 config3;
 
 	rtl8180_rtx_disable(dev);
 	rtl8180_reset(dev);
@@ -3247,12 +3244,6 @@ void rtl8180_adapter_start(struct net_device *dev)
 
 	rtl8180_beacon_tx_disable(dev);
 
-	if(priv->card_type == CARDBUS ){
-		config3=read_nic_byte(dev, CONFIG3);
-		write_nic_byte(dev,CONFIG3,config3 | CONFIG3_FuncRegEn);
-		write_nic_word(dev,FEMR, FEMR_INTR | FEMR_WKUP | FEMR_GWAKE |
-			read_nic_word(dev, FEMR));
-	}
 	rtl8180_set_mode(dev, EPROM_CMD_CONFIG);
 	write_nic_dword(dev, MAC0, ((u32*)dev->dev_addr)[0]);
 	write_nic_word(dev, MAC4, ((u32*)dev->dev_addr)[1] & 0xffff );

drivers/staging/rtl8187se/r8180_rtl8225z2.c

@@ -23,7 +23,6 @@ static void write_rtl8225(struct net_device *dev, u8 adr, u16 data)
 	u16 out, select;
 	u8 bit;
 	u32 bangdata = (data << 4) | (adr & 0xf);
-	struct r8180_priv *priv = ieee80211_priv(dev);
 
 	out = read_nic_word(dev, RFPinsOutput) & 0xfff3;
 
@@ -33,7 +32,7 @@ static void write_rtl8225(struct net_device *dev, u8 adr, u16 data)
 	select = read_nic_word(dev, RFPinsSelect);
 
 	write_nic_word(dev, RFPinsSelect, select | 0x7 |
-		((priv->card_type == USB) ? 0 : SW_CONTROL_GPIO));
+		       SW_CONTROL_GPIO);
 
 	force_pci_posting(dev);
 	udelay(10);
@@ -71,16 +70,11 @@ static void write_rtl8225(struct net_device *dev, u8 adr, u16 data)
 	force_pci_posting(dev);
 	udelay(10);
 
-	write_nic_word(dev, RFPinsOutput, out |
-		((priv->card_type == USB) ? 4 : BB_HOST_BANG_EN));
+	write_nic_word(dev, RFPinsOutput, out | BB_HOST_BANG_EN);
 
-	write_nic_word(dev, RFPinsSelect, select |
-		((priv->card_type == USB) ? 0 : SW_CONTROL_GPIO));
+	write_nic_word(dev, RFPinsSelect, select | SW_CONTROL_GPIO);
 
-	if (priv->card_type == USB)
-		mdelay(2);
-	else
-		rtl8185_rf_pins_enable(dev);
+	rtl8185_rf_pins_enable(dev);
 }
 
 static const u16 rtl8225bcd_rxgain[] = {
@@ -174,15 +168,9 @@ static void rtl8225_SetTXPowerLevel(struct net_device *dev, short ch)
 	u8 cck_power_level = 0xff & priv->chtxpwr[ch];
 	u8 ofdm_power_level = 0xff & priv->chtxpwr_ofdm[ch];
 
-	if (priv->card_type == USB) {
-		max_cck_power_level = 11;
-		max_ofdm_power_level = 25;
-		min_ofdm_power_level = 10;
-	} else {
-		max_cck_power_level = 35;
-		max_ofdm_power_level = 35;
-		min_ofdm_power_level = 0;
-	}
+	max_cck_power_level = 35;
+	max_ofdm_power_level = 35;
+	min_ofdm_power_level = 0;
 
 	if (cck_power_level > max_cck_power_level)
 		cck_power_level = max_cck_power_level;
@@ -629,8 +617,7 @@ void rtl8225z2_rf_init(struct net_device *dev)
 
 	priv->chan = channel;
 
-	if (priv->card_type != USB)
-		rtl8225_host_pci_init(dev);
+	rtl8225_host_pci_init(dev);
 
 	write_nic_dword(dev, RF_TIMING, 0x000a8008);
 
@@ -653,7 +640,7 @@ void rtl8225z2_rf_init(struct net_device *dev)
 	write_rtl8225(dev, 0x4, 0x8c3); mdelay(1);
 	write_rtl8225(dev, 0x5, 0xc72); mdelay(1);
 	write_rtl8225(dev, 0x6, 0xe6);  mdelay(1);
-	write_rtl8225(dev, 0x7, ((priv->card_type == USB)? 0x82a : rtl8225_chan[channel]));  mdelay(1);
+	write_rtl8225(dev, 0x7, rtl8225_chan[channel]);  mdelay(1);
 	write_rtl8225(dev, 0x8, 0x3f);  mdelay(1);
 	write_rtl8225(dev, 0x9, 0x335); mdelay(1);
 	write_rtl8225(dev, 0xa, 0x9d4); mdelay(1);
@@ -679,13 +666,6 @@ void rtl8225z2_rf_init(struct net_device *dev)
 
 	write_rtl8225(dev, 0x2, 0xc4d);
 
-	if (priv->card_type == USB) {
-		mdelay(200);
-
-		write_rtl8225(dev, 0x2, 0x44d);
-		mdelay(100);
-	}
-
 	/* FIXME!! rtl8187 we have to check if calibrarion
 	 * is successful and eventually cal. again (repeat
 	 * the two write on reg 2)
@@ -705,9 +685,6 @@ void rtl8225z2_rf_init(struct net_device *dev)
 
 	write_rtl8225(dev, 0x0, 0x2bf);
 
-	if (priv->card_type != USB)
-		rtl8185_rf_pins_enable(dev);
-
 	for (i = 0; i < 128; i++) {
 		data = rtl8225_agc[i];
 
@@ -724,7 +701,7 @@ void rtl8225z2_rf_init(struct net_device *dev)
 
 	write_phy_ofdm(dev, 0x00, 0x01); mdelay(1);
 	write_phy_ofdm(dev, 0x01, 0x02); mdelay(1);
-	write_phy_ofdm(dev, 0x02, ((priv->card_type == USB) ? 0x42 : 0x62)); mdelay(1);
+	write_phy_ofdm(dev, 0x02, 0x62); mdelay(1);
 	write_phy_ofdm(dev, 0x03, 0x00); mdelay(1);
 	write_phy_ofdm(dev, 0x04, 0x00); mdelay(1);
 	write_phy_ofdm(dev, 0x05, 0x00); mdelay(1);
@@ -772,7 +749,7 @@ void rtl8225z2_rf_init(struct net_device *dev)
 	write_phy_cck(dev, 0x6, 0xfc); mdelay(1);
 	write_phy_cck(dev, 0x7, 0x78); mdelay(1);
 	write_phy_cck(dev, 0x8, 0x2e); mdelay(1);
-	write_phy_cck(dev, 0x10, ((priv->card_type == USB) ? 0x9b: 0x93)); mdelay(1);
+	write_phy_cck(dev, 0x10, 0x93); mdelay(1);
 	write_phy_cck(dev, 0x11, 0x88); mdelay(1);
 	write_phy_cck(dev, 0x12, 0x47); mdelay(1);
 	write_phy_cck(dev, 0x13, 0xd0);
@@ -806,12 +783,8 @@ void rtl8225z2_rf_init(struct net_device *dev)
 	/* switch to high-speed 3-wire
 	 * last digit. 2 for both cck and ofdm
 	 */
-	if (priv->card_type == USB)
-		write_nic_dword(dev, 0x94, 0x3dc00002);
-	else {
-		write_nic_dword(dev, 0x94, 0x15c00002);
-		rtl8185_rf_pins_enable(dev);
-	}
+	write_nic_dword(dev, 0x94, 0x15c00002);
+	rtl8185_rf_pins_enable(dev);
 
 	rtl8225_rf_set_chan(dev, priv->chan);
 }