提交 8a74e9ff 编写于 作者: G Greg Kroah-Hartman

Revert "tty: serial: OMAP: ensure FIFO levels are set correctly in non-DMA mode"

This reverts commit 0a697b22 as Paul
wants to rework it.

Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Govindraj Raja <govindraj.r@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
上级 af681cad
......@@ -46,18 +46,6 @@
#define DEFAULT_CLK_SPEED 48000000 /* 48Mhz*/
/* SCR register bitmasks */
#define OMAP_UART_SCR_RX_TRIG_GRANU1_MASK (1 << 7)
#define OMAP_UART_SCR_TX_TRIG_GRANU1_MASK (1 << 6)
/* FCR register bitmasks */
#define OMAP_UART_FCR_RX_FIFO_TRIG_SHIFT 6
#define OMAP_UART_FCR_RX_FIFO_TRIG_MASK (0x3 << 6)
#define OMAP_UART_FCR_TX_FIFO_TRIG_SHIFT 4
/* TLR register bitmasks */
#define OMAP_UART_TLR_TX_FIFO_TRIG_DMA_SHIFT 0
static struct uart_omap_port *ui[OMAP_MAX_HSUART_PORTS];
/* Forward declaration of functions */
......@@ -706,7 +694,6 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
unsigned char efr = 0;
unsigned long flags = 0;
unsigned int baud, quot;
u32 tlr;
switch (termios->c_cflag & CSIZE) {
case CS5:
......@@ -824,28 +811,14 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
up->mcr = serial_in(up, UART_MCR);
serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
/* FIFO ENABLE, DMA MODE */
up->scr |= OMAP_UART_SCR_TX_TRIG_GRANU1_MASK;
up->scr |= OMAP_UART_SCR_RX_TRIG_GRANU1_MASK;
serial_out(up, UART_FCR, up->fcr);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
if (up->use_dma) {
tlr = 0;
} else {
up->scr &= ~OMAP_UART_SCR_TX_EMPTY;
/* Set receive FIFO threshold to 1 */
up->fcr &= ~OMAP_UART_FCR_RX_FIFO_TRIG_MASK;
up->fcr |= (0x1 << OMAP_UART_FCR_RX_FIFO_TRIG_SHIFT);
/* Set TX FIFO threshold to "63" (actually 1) */
up->fcr |= (0x3 << OMAP_UART_FCR_TX_FIFO_TRIG_SHIFT);
tlr = (0xf << OMAP_UART_TLR_TX_FIFO_TRIG_DMA_SHIFT);
serial_out(up, UART_TI752_TLR, 0);
up->scr |= (UART_FCR_TRIGGER_4 | UART_FCR_TRIGGER_8);
}
serial_out(up, UART_TI752_TLR, tlr);
serial_out(up, UART_FCR, up->fcr);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(up, UART_OMAP_SCR, up->scr);
serial_out(up, UART_EFR, up->efr);
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册